The CS2 region contains the Assabet board configuration and status
registers, which are 32-bit. Unfortunately, some boot loaders do not
configure this region correctly, leaving it setup as a 16-bit region.
Fix this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SA1100 was implementing its own variants of gpio_get_value()
and gpio_set_value() and only selectively falling back to
gpiolib for extended (EGPIO) handling. However the driver in
gpio/gpio-sa1100.c already handles the same functionality for
these lines, yet remain unused.
The only upside would be things like a timing-critical hotpath
on bit-banged GPIO, but that kind of things does not seem to
happen on these GPIOs, so it is not worth having the extra
complexity.
Tested with some buttons on the Compaq iPAQ H3630.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When removing the complex GPIO interface from the SA1100 machines,
we also removed the implicit #includes for a few header files
that was included by <linux/gpio.h> thru <mach/gpio.h>, causing
a compile warning on the simpad boardfile, as <asm/irq.h> was no
longer #included, as follows:
./../arch/arm/include/asm/irq.h:9:0: warning: "NR_IRQS" redefined
[enabled by default]
#define NR_IRQS NR_IRQS_LEGACY
^
In file included from ../../arch/arm/mach-sa1100/simpad.c:29:0:
../../arch/arm/mach-sa1100/include/mach/irqs.h:87:0: note: this is the
location of the previous definition
#define NR_IRQS (IRQ_BOARD_START + NR_IRQS_LOCOMO)
This resolves the problem by explicitly including <asm/irq.h>
into the simpad boardfile.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the prototype of cpufreq_drivers target routines is:
int target(struct cpufreq_policy *policy, unsigned int target_freq,
unsigned int relation);
And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.
So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.
This patch implements the new light weight prototype for target_index() routine.
It looks like this:
int target_index(struct cpufreq_policy *policy, unsigned int index);
CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.
This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.
It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the sa11x0 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch exposes sa11x0's frequency table to cpufreq core. It always existed
but not as an array frequencies and not in the format cpufreq core wants it to.
Also it was present in the unit of 100kHz earlier which is made consistent with
cpufreq core now, i.e. kHz.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Zaurus collie contains 2 LH28F640BFHE-PTTL90 (64M 4Mx16) and
at the moment cfi will not detect the collie NOR.
In the meanwhile we can revert to the jedec-probe map which has been
fixed with following commit:
mtd: jedec_probe: fix LH28F640BF definition
fe2f4c8e0b
Somehow this is unsatisfactory because the flash is mounted READ ONLY
(as from factory, with a RO cramfs)
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch moves cpufreq driver of ARM based sa11x0 platform to drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cpus contains all online cpus that have single shared clock line. And
their frequencies are always updated together.
Many SMP system's cpufreq drivers take care of this in individual drivers but
the best place for this code is in cpufreq core.
This patch modifies cpufreq_notify_transition() to notify frequency change for
all cpus in policy->cpus and hence updates all users of this API.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9.
This includes a few larger patches for GPIO on the Marvell PXA platform
and a lot of Samsung specific bug fixes, as well as a series from Arnd
to fix older build warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BbV4
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM SoC bug fixes from Arnd Bergmann:
"Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9. This includes
a few larger patches for GPIO on the Marvell PXA platform and a lot of
Samsung specific bug fixes, as well as a series from Arnd to fix older
build warnings."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ
ARM: imx: MACH_MX31ADS_WM1133_EV1 needs REGULATOR_WM8350
scripts/sortextable: silence script output
ARM: s3c: i2c: add platform_device forward declaration
ARM: mvebu: allow selecting mvebu without Armada XP
ARM: pick Versatile by default for !MMU
ARM: integrator: fix build with INTEGRATOR_AP off
ARM: integrator/versatile: fix NOMMU warnings
ARM: sa1100: don't warn about mach/ide.h
ARM: shmobile: fix defconfig warning on CONFIG_USB
ARM: w90x900: fix legacy assembly syntax
ARM: samsung: fix assembly syntax for new gas
ARM: disable virt_to_bus/virt_to_bus almost everywhere
ARM: dts: Correct pin configuration of SD 4 for exynos4x12-pinctrl
ARM: SAMSUNG: Silence empty switch warning in fimc-core.h
ARM: SAMSUNG: Silence empty switch warning in sdhci.h
ARM: msm: proc_comm_boot_wait should not be __init
arm: vt8500: Update MAINTAINERS entry for arch-vt8500
ARM: integrator: ensure ap_syscon_base is initialised when !CONFIG_MMU
ARM: S5PV210: Fix early uart output in fifo mode
...
Patch "16559ae kgdb: remove #include <linux/serial_8250.h> from kgdb.h
caused assabet_defconfig to fail, since assabet.c did not
itself include linux/platform_device.h, although it needs it:
In file included from include/linux/mfd/ucb1x00.h:13:0,
from arch/arm/mach-sa1100/assabet.c:19:
include/linux/mfd/mcp.h:22:16: error: field 'attached_device' has incomplete type
include/linux/mfd/mcp.h:48:23: error: field 'drv' has incomplete type
In file included from arch/arm/mach-sa1100/assabet.c:19:0:
include/linux/mfd/ucb1x00.h:137:16: error: field 'dev' has incomplete type
arch/arm/mach-sa1100/assabet.c: In function 'assabet_init':
arch/arm/mach-sa1100/assabet.c:343:3: error: implicit declaration of function 'platform_device_register_simple' [-Wimplicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This warning has existed since before the start of (git) history.
Apparently nobody has bothered to fix it in a long time, and
this is unlikely to change. Note that the file that the warning
refers to has moved to a different location and was subsequently
deleted in 2008.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ9WSiAAoJEFBXWFqHsHzOkpYH/iHOomqWknjg0YjeUKmoqnk+
UnAiP/OD0pOuqdC3izSq5rAaxeCn2ESYhXWdHH3LQFNnhwDPOItagY3T1dBgJH0G
KvO3wDj0K1jUM6Nzt4hta4pnCc/KClyCcVjYrP5pE+bs3NzOzxvfj2tPc81lI0Iy
rnkMLWw6gVRllhecUezt3TOd/GfI7NwuyjjBOLelOerbImWFqLOCNIZSRQlazbyS
hFh4OkR7yoU6vEvPdmS4B4A5PWBHlxiUS6Wr4v+doGFPiFgR05tJodLnnJ/KGWmG
LFY99MyeBvcgiUlFcUpiVLYpWJh+7IB1LJH+IGNJbWFYC+Yvn/o9IRYO8kvuiYE=
=weNJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/cleanup
From Shawn Guo:
The series cleans up ARCH_HAS_DECOMP_WDOG and arch_decomp_wdog which
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
* tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: samsung: remove unused arch_decomp_wdog() code
ARM: remove unused arch_decomp_wdog()
ARM: decompress: remove unused ARCH_HAS_DECOMP_WDOG
Signed-off-by: Olof Johansson <olof@lixom.net>
Clockevent cleanup series from Shawn Guo.
Resolved move/change conflict in mach-pxa/time.c due to the sys_timer
cleanup.
* clocksource/cleanup:
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
+ sync to Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-pxa/time.c
The clockevent core is able to figure out the best mult and shift,
calculate min_delta_ns and max_delta_ns, with the necessary info passed
into clockevents_config_and_register(). Use this combined configure
and register function where possible to make the codes less error prone
and gain some positive diff stat.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Roland Stigge <stigge@antcom.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brown <davidb@codeaurora.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Barry Song <baohua.song@csr.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
With ARCH_HAS_DECOMP_WDOG removed from arch/arm/boot/compressed/decompress.c,
all the arch_decomp_wdog() definition at platform level is unneeded.
Remmove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Move sa1100's timer suspend/resume functions from struct sys_timer
sa1100_timer into struct clock_event_device ckevt_sa1100_osmr0. This
will allow the sys_timer suspend/resume fields to be removed, and
eventually lead to a complete removal of struct sys_timer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is really driver platform data, so move it to the appropriate
directory.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell fixed this bogus warning before in 2f3eca8b4f "Shut up gcc
warning in assabet.c", but apparently gcc has become smarter (or dumber)
since 2005, and the same warning came up again.
This uses the uninitialized_var() macro to convince gcc that the
variable is actually being initialized. 100 times in fact.
Without this patch, building assabet_defconfig results in:
arch/arm/mach-sa1100/assabet.c: In function 'fixup_assabet':
arch/arm/mach-sa1100/assabet.c:397:6: warning: 'scr' may be used uninitialized in this function [-Wuninitialized]
arch/arm/mach-sa1100/assabet.c:389:16: note: 'scr' was declared here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM updates from Russell King:
"This is the first chunk of ARM updates for this merge window.
Conflicts are expected in two files - asm/timex.h and
mach-integrator/integrator_cp.c. Nothing particularly stands out more
than anything else.
Most of the growth is down to the opcodes stuff from Dave Martin,
which is countered by Rob's patches to use more of the asm-generic
headers on ARM."
(A few more conflicts grew since then, but it all looked fairly trivial)
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (44 commits)
ARM: 7548/1: include linux/sched.h in syscall.h
ARM: 7541/1: Add ARM ERRATA 775420 workaround
ARM: ensure vm_struct has its phys_addr member filled in
ARM: 7540/1: kexec: Check segment memory addresses
ARM: 7539/1: kexec: scan for dtb magic in segments
ARM: 7538/1: delay: add registration mechanism for delay timer sources
ARM: 7536/1: smp: Formalize an IPI for wakeup
ARM: 7525/1: ptrace: use updated syscall number for syscall auditing
ARM: 7524/1: support syscall tracing
ARM: 7519/1: integrator: convert platform devices to Device Tree
ARM: 7518/1: integrator: convert AMBA devices to device tree
ARM: 7517/1: integrator: initial device tree support
ARM: 7516/1: plat-versatile: add DT support to FPGA IRQ
ARM: 7515/1: integrator: check PL010 base address from resource
ARM: 7514/1: integrator: call common init function from machine
ARM: 7522/1: arch_timers: register a time/cycle counter
ARM: 7523/1: arch_timers: enable the use of the virtual timer
ARM: 7531/1: mark kernelmode mem{cpy,set} non-experimental
ARM: 7520/1: Build dtb files in all target
ARM: Fix build warning in arch/arm/mm/alignment.c
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the sa1100 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jochen Friedrich <jochen@scram.de>
From Bryan Wu <bryan.wu@canonical.com>:
Based on Linus Walleij's ARM LED consolidation work, this patchset introduce a
new generic led trigger for CPU not only for ARM but also for others.
For enabling CPU idle event, CPU arch code should call ledtrig_cpu() stub to
trigger idle start or idle end event.
These patches convert old style LED driver in arch/arm to gpio_led or new led
driver interface. Against 3.5 release and build successfully for all the machines.
Test ledtrig-cpu driver on OMAP4 Panda board.
v9 --> v10
* fix compiling issue on versatile_defconfig reported by Russell King
* rebase to 3.5 kernel and move patches to new git tree
v8 --> v9:
* use mutex to replace rw_sema pointed out by Tim Gardner
* add a new struct led_trigger_cpu
* add lock_is_inited to record mutex lock initialization
v6 --> v7:
* add a patch to unify the led-trigger name
* fix some typo pointed
* use BUG_ON to detect CPU numbers during building stage
v5 --> v6:
* replace __get_cpu_var() to per_cpu()
* remove smp_processor_id() which is wrong with for_each_possible_cpu()
* test on real OMAP4 Panda board
* add comments about CPU hotplug in the CPU LED trigger driver
v4 --> v5:
* rebase all the patches on top of latest linux-next
* replace on_each_cpu() with for_each_possible_cpu()
* add some description of ledtrig_cpu() API
* remove old leds code from driver nwflash.c, which should use a new led trigger then
* this trigger driver can be built as module now
v3 --> v4:
* fix a typo pointed by Jochen Friedrich
* fix some building errors
* add Reviewed-by and Tested-by into patch log
v2 --> v3:
* almost rewrote the whole ledtrig-cpu driver, which is more simple
* every CPU will have a per-CPU trigger
* cpu trigger can be assigned to any leds
* fix a lockdep issue in led-trigger common code
* other fix according to review
v1 --> v2:
* remove select operations in Kconfig of every machines
* add back supporting of led in core module of mach-integrator
* solidate name scheme in ledtrig-cpu.c
* add comments of CPU_LED_* cpu led events
* fold patches of RealView and Versatile together
* add machine_is_ check during assabet led driver init
* add some Acked-by in patch logs
* remove code for simpad machine in machine-sa11000, since Jochen Friedrich
introduced gpiolib and gpio-led driver for simpad
* on Assabet and Netwinder machine, LED operations is reversed like:
setting bit means turn off leds
clearing bit means turn on leds
* add a new function to read CM_CTRL register for led driver
* 'for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
ARM: use new LEDS CPU trigger stub to replace old one
ARM: mach-sa1100: retire custom LED code
ARM: mach-omap1: retire custom LED code
ARM: mach-pnx4008: remove including old leds event API header file
ARM: plat-samsung: remove including old leds event API header file
ARM: mach-pxa: retire custom LED code
char: nwflash: remove old led event code
ARM: mach-footbridge: retire custom LED code
ARM: mach-ebsa110: retire custom LED code
ARM: mach-clps711x: retire custom LED code of P720T machine
ARM: mach-integrator: retire custom LED code
ARM: mach-integrator: move CM_CTRL to header file for accessing by other functions
ARM: mach-orion5x: convert custom LED code to gpio_led and LED CPU trigger
ARM: mach-shark: retire custom LED code
ARM: mach-ks8695: remove leds driver, since nobody use it
ARM: mach-realview and mach-versatile: retire custom LED code
ARM: at91: convert old leds drivers to gpio_led and led_trigger drivers
led-triggers: create a trigger for CPU activity
Conflicts:
arch/arm/mach-clps711x/p720t.c
arch/arm/mach-sa1100/leds-cerf.c
arch/arm/mach-sa1100/leds-lart.c
Let's hope this is the last time we pull this and it doesn't cause
more trouble. I have verified that version 10 causes no build
warnings or errors any more, and the patches still look good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The sa1100 definition of the io_p2v macro has changed in v3.6, and this one
file stopped working because of that.
Without this patch, building hackkit_defconfig results in:
arch/arm/mach-sa1100/leds-hackkit.c: In function 'hackkit_leds_event':
arch/arm/mach-sa1100/leds-hackkit.c:39:4: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
This patch allows a timer-based delay implementation to be selected by
switching the delay routines over to use get_cycles, which is
implemented in terms of read_current_timer. This further allows us to
skip the loop calibration and have a consistent delay function in the
face of core frequency scaling.
To avoid the pain of dealing with memory-mapped counters, this
implementation uses the co-processor interface to the architected timers
when they are available. The previous loop-based implementation is
kept around for CPUs without the architected timers and we retain both
the maximum delay (2ms) and the corresponding conversion factors for
determining the number of loops required for a given interval. Since the
indirection of the timer routines will only work when called from C,
the sa1100 sleep routines are modified to branch to the loop-based delay
functions directly.
Tested-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the OS timer registers have IOMEM like properities so they can
be passed to readl_relaxed/writel_relaxed() et.al. rather than being
straight volatile dereferences. Add linux/io.h includes where
required.
linux/io.h includes added to arch/arm/mach-sa1100/cpu-sa1100.c,
arch/arm/mach-sa1100/jornada720_ssp.c, arch/arm/mach-sa1100/leds-lart.c
drivers/input/touchscreen/jornada720_ts.c, drivers/pcmcia/sa1100_shannon.c
from Arnd.
This fixes these warnings:
arch/arm/mach-sa1100/time.c: In function 'sa1100_timer_init':
arch/arm/mach-sa1100/time.c:104: warning: passing argument 1 of 'clocksource_mmio_init' discards qualifiers from pointer target type
arch/arm/mach-pxa/time.c: In function 'pxa_timer_init':
arch/arm/mach-pxa/time.c:126: warning: passing argument 1 of 'clocksource_mmio_init' discards qualifiers from pointer target type
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No file includes this header. It has never been included since at least
v2.6.12-rc2. It can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All (in tree) users of old mach/SA-1111.h were already updated to
include asm/hardware/sa1111.h in v2.6.12-rc2. The old header can safely
be removed now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull arm updates from Russell King:
"This contains both some fixes found when trying to get the
Assabet+neponset setup as a replacement firewall with a 3c589 PCMCIA
card, and a bunch of changes from Al to fix up the ARM signal
handling, particularly some of the restart behaviour."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: neponset: make sure neponset_ncr_frob() is exported
ARM: fix out[bwl]()
arm: don't open-code ptrace_report_syscall()
arm: bury unused _TIF_RESTORE_SIGMASK
arm: remove unused restart trampoline
arm: new way of handling ERESTART_RESTARTBLOCK
arm: if we get into work_pending while returning to kernel mode, just go away
arm: don't call try_to_freeze() from do_signal()
arm: if there's no handler we need to restore sigmask, syscall or no syscall
arm: trim _TIF_WORK_MASK, get rid of useless test and branch...
arm: missing checks of __get_user()/__put_user() return values
This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=21h6
-----END PGP SIGNATURE-----
Merge tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
This function is used by modules (such as the SA1111 PCMCIA driver)
so it needs to be exported.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most PCI implementations perform simple root bus scanning. Rather than
having each group of platforms provide a duplicated bus scan function,
provide the PCI configuration ops structure via the hw_pci structure,
and call the root bus scanning function from core ARM PCI code.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By Shawn Guo
via Shawn Guo
* 'clean/late_initcall_v2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
DEFINE_RES_MEM() takes the size of resource as a second argument,
not the end address. Passing end address leads to following error
in runtime during device registration:
sa1100-rtc: failed to claim resource 0
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Commit 086ada54ab
"FB: sa1100: remove global sa1100fb_.*_power function pointers"
got rid of all instances but one in locomolcd.c -- which was
conditional on CONFIG_SA1100_COLLIE. The associated .power
field which replaces the global is populated in mach-sa1100/collie.c
so move the assignment there, but make it conditional on the
locomolcd support, so use CONFIG_BACKLIGHT_LOCOMO in that file.
Cc: arm@kernel.org
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
In preparation to convert SA1100 to sparse irq, set .nr_irqs for each machine
and explicitly include mach/irqs.h as needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the new unused DMA controller definitions from mach/SA-1100.h.
These are now private to the SA-11x0 DMA engine driver and contained
within the driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that all users are converted over to using the DMA engine API,
we can get rid of the old platform dependent DMA driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sa1111 support will ioremap() the device; there is no need for
platforms to setup a static mapping for this. Remove the static
mapping for this device from badge4, jornada720 and neponset.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms don't want certain devices to be registered, because,
eg, the interface is not wired. Provide a way for platforms to
prevent various devices from being registered via a devid bitmask in
the platform data.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull #3 ARM updates from Russell King:
"This adds gpio support to soc_common, allowing an amount of code to be
deleted from each PCMCIA socket driver for the PXA/SA11x0 SoCs."
* 'pcmcia' of git://git.linaro.org/people/rmk/linux-arm:
PCMCIA: sa1111: rename sa1111 socket drivers to have sa1111_ prefix.
PCMCIA: make lubbock socket driver part of sa1111_cs
PCMCIA: add Kconfig control for building sa11xx_base.c
PCMCIA: sa1111: jornada720: no need to disable IRQs around sa1111_set_io
PCMCIA: sa1111: pass along sa1111_pcmcia_configure_socket() failure code
PCMCIA: soc_common: remove explicit wrprot initialization in socket drivers
PCMCIA: soc_common: remove soc_pcmcia_*_irqs functions
PCMCIA: sa11x0: h3600: convert to use new irq/gpio management
PCMCIA: sa11x0: simpad: convert to use new irq/gpio management
PCMCIA: sa11x0: shannon: convert to use new irq/gpio management
PCMCIA: sa11x0: nanoengine: convert reset handling to use GPIO subsystem
PCMCIA: sa11x0: nanoengine: convert to use new irq/gpio management
PCMCIA: sa11x0: cerf: convert reset handling to use GPIO subsystem
PCMCIA: sa11x0: cerf: convert to use new irq/gpio management
PCMCIA: sa11x0: assabet: convert to use new irq/gpio management
PCMCIA: sa1111: use new per-socket irq/gpio infrastructure
PCMCIA: pxa: convert PXA socket drivers to use new irq/gpio management
PCMCIA: soc_common: add GPIO support for card status signals
PCMCIA: soc_common: move common initialization into soc_common
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
Add sa11x0 DMA platform device and resources to the list of
generic platform devices for SA11x0 machines.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add rtc clock support and clean clock support for gpio.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to hard coded irq in rtc-sa1100 driver since we could share
it among arch-sa1100/arch-pxa/arch-mmp.
We still keep hard coded register address since the requirement is
enabling both rtc-sa1100 and rtc-pxa driver. The register addresses
are conflict since they're only two wrappers on the same rtc device.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Convert the sa11x0 framebuffer driver to obtain the base address of its
hardware registers from the platform resources, and ioremap this rather
than relying on the static mappings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Convert Simpad socket driver to use the new irq/gpio management.
This is slightly more involved because we have to touch the private
platform header file to modify the GPIO bitmasks to be GPIO numbers.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert Shannon socket driver to use the new irq/gpio management.
This is slightly more involved because we have to touch the private
platform header file to modify the GPIO bitmasks to be GPIO numbers.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than accessing GPSR and GPCR directly, use the GPIO subsystem
instead.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we have platform data contained within the individual board
code, we can get rid of the global function pointers, placing them
inside the platform data instead.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform data out of the sa1100fb driver into the various
platform files themselves.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the assabet specific reset handling out of mcp-sa11x0.c, into its
board file. This leaves the mcp code free from all board specific
details.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ucb1x00 platform data to enable GPIO support on the UCB1300 device.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch taken from 5dd7bf59e0 (ARM: sa11x0: Implement autoloading of codec
and codec pdata for mcp bus.) by Jochen Friedrich <jochen@scram.de>.
This adds just the codec data part of the patch.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the handling of the 5v supply into badge4.c, removing this board
specific detail from the sa1111 ohci driver.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we ioremap() the neponset register space, there's no need
to static map the neponset registers. Get rid of this static mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the board specific neponset register definitions to the board
file, rather than mach/neponset.h. However, as the NCR_0 register
definitions are used by some drivers, leave these behind.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The neponset board is a daughter board for the Assabet. Create the
neponset platform device in assabet.c, where we don't have to wrap
it with machine_is_assabet() stuff. We also create this device
dynamically rather than keeping it as a static device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suspend and resume in the _noirq state, so that we're saving the
state of the modem control signals as late as possible, and restoring
them as early as possible. There's nothing to do in thaw/poweroff
methods as we've already saved the necessary state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Complete the neponset device resources by covering the children's
memory resources in the parent neponset device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Obtain the parent IRQ from the neponset device resource rather than
hard-coding it into the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the necessary allocation/freeing functionality to support
sparse IRQs with the Neponset device. On non-sparse IRQ platforms,
this allows us to dynamically allocate from within the available IRQ
number space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use platform_device_register_full() to dynamically create the various
neponset child platform devices, and place them below the neponset
device itself to ensure proper PM ordering and device structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Save and restore the modem output control register across a suspend/
resume, as well as the NCR register. Place these in a locally
allocated data structure rather than needing a new static variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having direct register accesses to NCR_0 scattered amongst
the code, provide a function instead. This contains the necessary
race protection for this platform, ensuring that updates to this
register are safe.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since ARM was converted to genirq, the neponset IRQ implementation has
gradually broken as a result of various subtle changes being introduced
into genirq.
It used to be that simple IRQs did not need an IRQ chip. This is no
longer the case, and genirq barfs in irq_set_handler(). Fix this by
introducing a dummy no-op chip, and registering it along with the flow
handler.
Neponset IRQs really don't have any masking ability - all we have is a
status register to allow us to decode the source, and a three input OR
gate inside a CPLD.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GPIO27 is just connected to a CPLD input without any pull-ups or pull-
downs. If GPIO27 is left as an input, it will float around mid-supply,
which for CMOS inputs is the worst place for a pin to be. Ensure that
this pin is driven.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King