These helper functions get and set a 64-bit control's value from within
a driver. They are similar to v4l2_ctrl_[gs]_ctrl() but operate on
64-bit integer controls instead of 32-bit controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial version of this driver.
The full datasheets are available from the Analog Devices website:
http://ez.analog.com/docs/DOC-1741
Not all features of the receiver are supported by this driver for various
reasons. Most notably:
- No CEC support (the CEC API needs a lot more discussion)
- No HDCP repeater support (we don't use that either)
I'm sure that there are more things missing, but this driver does work
well for our hardware.
Note that I am using the register addresses instead of register names: the
datasheet containing the register descriptions is organized by register
address. Using names would make the datasheet lookup very hard. An attempt
was made to try and document what is being done when registers are used
instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial version of this driver.
The full datasheets are available from the Analog Devices website:
http://ez.analog.com/docs/DOC-1545
Not all features of the receiver are supported by this driver for various
reasons. Most notably:
- No CEC support (the CEC API needs a lot more discussion)
- Only port A of the four HDMI input ports is implemented (our hardware only
uses that port)
- No HDCP repeater support (we don't use that either)
And since there are some 600-odd pages of datasheet for this single device,
I'm sure that there are many more things missing, but this driver does work
well for our hardware.
Note that I am using the register addresses instead of register names: the
datasheet containing the register descriptions is organized by register
address. Using names would make the datasheet lookup very hard. An attempt
was made to try and document what is being done when registers are used
instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These two helper functions detect whether the analog video timings detected
by the video receiver match the VESA CVT or GTF standards.
They basically do the inverse of the CVT and GTF modeline calculations.
This patch also adds a helper function that will determine the aspect ratio
based on the provided EDID values. This aspect ratio can be given to the GTF
helper function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the v4l_match_dv_timings function that can be used to compare two
v4l2_dv_timings structs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add .get_selection() and .set_selection() soc-camera host driver
operations. Additionally check, that the user is not trying to change the
output sizes during a running capture.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of forcing all soc-camera drivers to go through the mid-layer to
handle power management, create soc_camera_power_[on|off]() functions
that can be called from the subdev .s_power() operation to manage
regulators and platform-specific power handling. This allows non
soc-camera hosts to use soc-camera-aware clients.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[g.liakhovetski@gmx.de: fix compile breakage]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the driver for the IR transmitter diode found on the Nokia
N900 (also known as RX51) device. The driver is mostly the same as
found in the original 2.6.28 based kernel that comes with the device.
The following modifications have been made compared to the original
driver version:
- Adopt to the changes that has happen in the kernel during the past
five years, such as the change in the include paths
- The OMAP DM-timers require much more care nowadays. The timers need
to be enabled and disabled or otherwise many actions fail. Timers
must not be freed without first stopping them or otherwise the timer
cannot be requested again.
The code has been tested with sending IR codes with N900 device
running Debian userland. The device receiving the codes was Anysee
DVB-C USB receiver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This callback were meant to allow overriding a FE callback, before its
call, but it is not really needed, as the callback can be intercepted
after tuner attachment.
Worse than that, only DVBv3 calls are intercepted this way, so a DVBv5
application will produce different effects than a DVBv3 one.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
[mchehab@redhat.com: fix a merge conflict at Documentation/video4linux/v4l2-framework.txt]
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the bridge automatically when the input format is YUYV8 or UYVY8.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The structure is only used to store configuration data and pass it to
CCDC configuration functions. Access the data directly from the
locations that need it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that needed V4L2_FL_LOCK_ALL_FOPS have been converted,
so remove this flag altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
I also removed some dead code in the form of the saa7146_devices list and
saa7146_devices_lock mutex: these were used once but that was a long time
ago.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the usual core support code for this new ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
add hardware clipping support for VPIF output data. This
is needed as it is possible that the external encoder
might get confused between the FF or 00 which are a part
of the data and that of the SAV or EAV codes.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's better to give platform code a chance to specify the allowed
protocols to use.
[mchehab@redhat.com: fix merge conflict with a patch that made
half of this change]
Signed-off-by: Du, Changbin <changbin.du@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add helper functions to make it easier to adapt drivers to vb2.
These helpers take care of core locking and check if the filehandle is the
owner of the queue.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prepares struct video_device for easier integration with vb2.
It also introduces a new lock that protects the vb2_queue. It is up
to the driver to use it or not. And the driver can associate an owner
filehandle with the queue to check whether queuing requests are
permitted for the calling filehandle.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l_i2c_print_ioctl wasn't used and v4l_print_ioctl could be replaced by
v4l_printk_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ADV7393 I²C-based video encoder driver. This driver has been tested on
custom hardware. It has been tested for composite output. It is derived from the
ADV7343 driver.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the input fields got removed from the userspace API,
there's no sense to keep there at the VB struct. Remove it.
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it possible for gpio-ir-recv users to choose a map name.
Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It should be a mistake due to copy & paste in header file
Correct it in videobuf2-dma-config.h for avoiding duplicate include it
Change-Id: I1f71fcec2889c033c7db380c58d9a1369c5afb35
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pixel rate control is required by the OMAP3 ISP driver and should be
implemented by all media controller-compatible sensor drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of providing a function in platform data, allow also providing the
name of the external clock and use it through the clock framework.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add another Medion X10 remote keymap. This is for the Medion OR2x
remotes with the Windows MCE button.
The receiver shipped with this remote has the same USB ID as the other
Medion receivers, but the name is different and is therefore used to
detect this variant.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is getting more entities to manage within single video pipeline
in newer SoCs. To simplify code put subdevs' pointer into an array
rather than adding new member in struct fimc_pipeline for each subdev.
This allows to easier handle subdev operations in proper order.
Additionally walk graph in one direction only in fimc_pipeline_prepare()
function to make sure we properly gather only media entities that below
to single data pipeline. This avoids wrong initialization in case where,
for example there are multiple active links from s5p-mipi-csis subdev
output pad.
struct fimc_pipeline declaration is moved to the driver's public header
to allow other drivers to reuse the fimc-lite driver added in subsequent
patches.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a capabilities field to the soc_camera_host structure to flag hosts
that support user-configurable line strides. soc_camera_try_fmt() then
passes the user-provided bytesperline and sizeimage format fields to
such hosts, and expects the host to check (and fix if needed) the
values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[g.liakhovetski@gmx.de: fix a typo in mx2_camera.c]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function returns the minimum size of an image for a given number of
bytes per line (as per the V4L2 specification), width and format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To compute the value of the v4l2_pix_format::bytesperline field, we need
information about planes layout for planar formats. The new enum
soc_mbus_layout conveys that information.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use "enum_framesizes" instead of "enum_fsizes" to more precisely follow
the name of the respective ioctl().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Sergio Aguirre <sergio.a.aguirre@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the V4L2_EVENT_SUB_FL_SEND_INITIAL was set, then the application expects
to receive an initial event of the initial value of the control.
However, commit c53c254933 that added the new
v4l2_subscribed_event_ops introduced a regression: while the code still queued
that initial event the __v4l2_event_queue_fh() function was modified to ignore
such requests if sev->elems was 0 (meaning that the event subscription wasn't
finished yet).
And sev->elems was only set to a non-zero value after the add operation
returned.
This patch fixes this by passing the elems value to the add function. Then the
add function can set it before queuing the initial event.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus/master: (805 commits)
tty: Fix LED error return
openvswitch: checking wrong variable in queue_userspace_packet()
bonding: Fix LACPDU rx_dropped commit.
Linux 3.4-rc7
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
MAINTAINERS: Add myself as the cpufreq maintainer
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
ks8851: Update link status during link change interrupt
...
Conflicts:
drivers/media/common/tuners/xc5000.c
drivers/media/common/tuners/xc5000.h
drivers/usb/gadget/uvc_queue.c
Pull media fixes from Mauro Carvalho Chehab:
"For a some fix patches for v3.4, including a regression fix at DVB core"
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca - sonixj: Fix a zero divide in isoc interrupt
[media] media: videobuf2-dma-contig: include header for exported symbols
[media] media: videobuf2-dma-contig: quiet sparse noise about plain integer as NULL pointer
[media] media: vb2-memops: Export vb2_get_vma symbol
[media] s5p-fimc: Correct memory allocation for VIDIOC_CREATE_BUFS
[media] s5p-fimc: Fix locking in subdev set_crop op
[media] dvb_frontend: fix a regression with DVB-S zig-zag
[media] fintek-cir: change || to &&
[media] V4L: Schedule V4L2_CID_HCENTER, V4L2_CID_VCENTER controls for removal
[media] rc: Postpone ISR registration
[media] marvell-cam: fix an ARM build error
[media] V4L: soc-camera: protect hosts during probing from overzealous user-space
Rename the function v4l2_dont_use_lock to v4l2_disable_ioctl_locking,
and rename v4l2_dont_use_cmd to v4l2_disable_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This flag is for legacy drivers only and will go away in the future.
A note regarding commit 5126f2590b
(v4l2-dev: add flag to have the core lock all file operations):
That commit message suggests that by not taking the core lock for fops
other than unlocked_ioctl all problems relating to AB-BA locking and
mm->mmap_sem are solved. This is not the case.
More work needs to be done by moving the core lock further down into
video_ioctl2. It should only be taken after the copy_from/to_user calls
are done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The querycap ioctl returned an incorrect version number and incorrect
capabilities (mixing up vbi and video caps).
The reason for that was that video nodes could do vbi activities: that
should be separated between the vbi and video nodes.
There were also a few minor problems with dbg_g/s_register that have
been resolved. The mxb/saa7146 driver now passes the v4l2_compliance tests.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_fh which gives you control events and priority handling for free.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was also a vbi_q and video_q in saa7146_fh, so that was confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This information can also be retrieved from struct video_device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fields are global and don't belong in a fh struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a global structure and does not belong to saa7146_fh.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is global information, not per-filehandle information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart