If CONFIG_PM is not set the PU power domain needs to be enabled always,
otherwise there are two failure scenarios which will hang the system if
one of the devices in the PU domain is accessed.
1. New DTs (4.1+) drop the "always-on" property from the PU regulator, so
if it isn't properly enabled by the GPC code it will be disabled at the
end of boot.
2. If the bootloader already disabled the PU domain the GPC explicitly
needs to enable it again, even if the kernel doesn't do any power
management. This is a bit hypothetical, as it requires to boot a
mainline kernel on a downstream bootloader, as no mainline bootloader
disables the PM domains.
Cc: <stable@vger.kernel.org> # 4.1
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVi4RMAAoJEFk3GJrT+8Zl6/kP/1Rv9O++1Kxua6R54Og6AF1J
0miFr2fnUrUWUYg/NVbseRH5bBe6N6ir3SQMfde8W2/QibEjOoEwSwrle+mC/eiq
CE0x0gtyRvXMrMU/FWkOvbmmw9uv5oz1z3IHZV6AiecNuSMLUBPfamryikQ8C+d1
O/QZtX543tJQJDOBihO5cuhoVVM37UX0unNmqGsyswlyqTPF8FxcIJAYVNtnxjmj
AFaOB0nDJKLKFTiX2Ype2wOxxJX1lrLatNo4W4T+YaaK+i1uCOhgTdSN+n49K7YA
KNDFEgZFQqT8VMJyG+eJVeYF+cI7yWQ7lBzIftPUjPk/7+dIHBjWPz2QdjVz3U38
kxncf4S9xGAF5G2rcKe4mFrfT3Y8QLWQpA/jFs06yLwW1O3Hlfq3DzMdGNcF7hth
17LOP8namn9+NepZEp/vAlFzRRypxWWtbkPNBIItkImC6zn0IiGjBy50DE1io27W
hmQcnMb7d+0wWl2Y8OmR2lZSB97JiRZkRYMCVHVt+0zGJzp4prLvl9wbjh1VXkPv
ERCDJ9nCmZsl7ZVmIXMI7KNXYuPNp7R/QAzCvuSUueswF0qxTAQ0VSSBwRMqvQsQ
UUNC6p63VnjUeMUdn2EBsUQZ0Uqw3t2U5TtvooHNt9FkiGsSpwjWrvVD+LItaPoJ
GPeeJrJaYQsDvTrO8wjU
=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0zof
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
If the devicetree is too old and does not provide the regulator and clocks
for the power domain, we need to avoid registering the power domain.
Otherwise runtime PM will try to control the domain, which will lead to
machine hangs without the proper DT configuration data.
This restores functionality to the kernel 4.0 level if an old DT is
detected, where the power domain is constantly powered on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The GPC rewrite to IRQ domains has been on the premise that it may break
suspend/resume for new kernels on old DT, but otherwise keep things working
from a user perspective. This was an accepted compromise to be able to move
the GIC cleanup forward.
What actually happened was that booting a new kernel on an old DT crashes
before even the console is up, so the user does not even see the warning
that the DT is too old. The warning message suggests that this has been
known before, which is clearly unacceptable.
Fix the early crash by mapping the GPC memory space if the IRQ controller
doesn't claim it. This keeps at least CPUidle and the needed CPU wakeup
workarounds working. With this fixed the system is able to boot up
properly minus the expected suspend/resume breakage.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This platform_driver does not need to set an owner as it will be
populated by the driver core.
The semantic patch that makes this change is available
in scripts/coccinelle/api/platform_no_drv_owner.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that the GPC has been converted to be a full blown irqchip
(and not a mole on the side of the GIC), booting a new kernel
with an old DT is likely to result in a rough ride for the user.
This patch makes sure such a situation is promptly detected and
the user made aware that a DT update is in order.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
While converting the GPC code to a stacked irqchip, we lost the
possibility to change the CPU affinity of an interrupt routed
through the GPC.
This patch restore the expected behaviour by forwarding the
affinity setup to the underlying irqchip (GIC).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
IMX6 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the fact that the GPC block is actually the first
interrupt controller in the chain, kernels with this patch
applied wont have any suspend-resume facility when booted
with old DTs, and old kernels with updated DTs won't even boot.
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
When generic pm domain support is enabled, the PGC can be used
to completely gate power to the PU power domain containing GPU3D,
GPU2D, and VPU cores.
This code triggers the PGC powerdown sequence to disable the GPU/VPU
isolation cells and gate power and then disables the PU regulator.
To reenable, the reverse powerup sequence is triggered after the PU
regulator is enabled again.
The GPU and VPU devices in the PU power domain temporarily need
to be clocked during powerup, so that the reset machinery can work.
[Avoid explicit regulator enabling in probe, unless !PM]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch introduces an independent cpuidle driver for
i.MX6SX, and supports arm power off in idle, totally
3 levels of cpuidle are supported as below:
1. ARM WFI;
2. SOC in WAIT mode;
3. SOC in WAIT mode + ARM power off.
ARM power off can save at least 5mW power.
This patch also replaces imx6q_enable_rbc with imx6_enable_rbc.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6 PM code seems to be quite creative in its use of irq_data,
using something that is very much a hardware interrupt number where
we expect a virtual one. Yes, it worked so far, but that's only
luck, and it will definitely explode in 3.19.
Fix it by using a pair of helper functions that deal with the
actual hardware.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
mach-imx directly references to the irq field in
struct irq_data, and uses this to directly poke hardware register.
But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different.
Just replacing all instances of irq with hwirq fixes the issue.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add standby mode support for suspend, to enter standby mode:
echo standby > /sys/power/state;
Use UART or RTC alarm to wake up system, when system enters
standby mode, SOC will enter STOP mode with ARM core kept
power on and 24M XTAL on.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
There is a defect in imx6 LPM design. When SW tries to enter low power
mode with following sequence, the chip will enter low power mode before
A9 CPU execute WFI instruction:
1. Set CCM_CLPCR[1:0] to 2'b00;
2. ARM CPU enters WFI;
3. ARM CPU wakeup from an interrupt event, which is masked by GPC or not
visible to GPC, such as interrupt from local timer;
4. Set CCM_CLPCR[1:0] to 2'b01 or 2'b10;
5. ARM CPU execute WFI.
Before the last step, the chip will enter WAIT mode if CCM_CLPCR[1:0] is
set to 2'b01, or enter STOP mode if CCM_CLPCR[1:0] is set to 2'b10.
The patch implements a recommended workaround for this issue.
1. SW triggers irq #32(IOMUX) to be always pending manually by setting
IOMUX_GPR1_GINT bit;
2. SW should then unmask it in GPC before setting CCM LPM;
3. SW should mask it right after CCM LPM is set (bit0-1 of CCM_CLPCR).
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
RBC is to control whether some ANATOP sub modules
can enter lpm mode when SOC is into STOP mode, if
RBC is enabled and PMIC_VSTBY_REQ is set, ANATOP
will have below behaviors:
1. Digital LDOs(CORE, SOC and PU) are bypassed;
2. Analog LDOs(1P1, 2P5, 3P0) are disabled;
As the 2P5 is necessary for DRAM IO pre-drive in
STOP mode, so we need to enable weak 2P5 in STOP
mode when 2P5 LDO is disabled.
For RBC settings, there are some rules as below
due to hardware design:
1. All interrupts must be masked during operating
RBC registers;
2. At least 2 CKIL(32K) cycles is needed after the
RBC setting is changed.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix the following sparse warnings:
arch/arm/mach-imx/gpc.c:29:6: warning: symbol 'imx_gpc_pre_suspend' was not declared. Should it be static?
arch/arm/mach-imx/gpc.c:43:6: warning: symbol 'imx_gpc_post_resume' was not declared. Should it be static?
arch/arm/mach-imx/gpc.c:71:6: warning: symbol 'imx_gpc_mask_all' was not declared. Should it be static?
arch/arm/mach-imx/gpc.c:83:6: warning: symbol 'imx_gpc_restore_all' was not declared. Should it be static?
arch/arm/mach-imx/gpc.c:122:13: warning: symbol 'imx_gpc_init' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- It's based on imx-cleanup-3.9 to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCRzjAAoJEFBXWFqHsHzOOTYH/2YiAhCXDoovJ++leTTBKoFO
kRx2gvV0oxQYAjvRX4IiiwcuWjbCQI8ugiKxeH9Vn+jwHD8jKqzTINEUVQfKUud6
s8AI1/EqKwKnEFYFs/Fg6WxZHuHpoL/clpRB/5wZw1KoChmte2OnVU7d9vOt67iN
l0P4nPR18iwU5LFoDCnqMX50Dp9C56KEF2JhzBCQKW9TtRclwpcBNy6AsHb/TNOe
/nHN+Ku6/3xQEz2MPQ9QdmgFxnp9Pr8R6leJNg1Vg6UGRYrKxy0zVo+oFEXAZuUw
v6gnhdlvO6Ki/IKHcWkw7Q7pUDTuB6SttirQE9mBlPdc0V3kTU82SVtX9WAQhSs=
=rVol
-----END PGP SIGNATURE-----
Merge tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx6q cpuidle support for 3.9
- It's based on imx-cleanup-3.9 to avoid conflicts.
* tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: support WAIT mode using cpuidle
ARM: imx: move imx6q_cpuidle_driver into a separate file
ARM: imx: mask gpc interrupts initially
ARM: imx: return zero in case next event gets a large increment
ARM: imx: Remove mx508 support
ARM: imx: Remove mach-mx51_3ds board
ARM: imx: use debug_ll_io_init() for imx6q
ARM: imx: remove unused imx6q_clock_map_io()
ARM: mach-imx: Kconfig: Do not select Babbage for MACH_IMX51_DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Still, two delete/change conflicts caused by imx/cleanup:
arch/arm/mach-imx/mach-mx50_rdp.c
arch/arm/mach-imx/mach-mx51_3ds.c
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
It adds a number of core drivers support for imx6q, including clock,
General Power Controller (gpc), Multi Mode DDR Controller(mmdc) and
System Reset Controller (src).
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Lucas Stach