Custom trampolines can only be enabled if there is only a single ops
attached to it. If there's only a single callback registered to a function,
and the ops has a trampoline registered for it, then we can call the
trampoline directly. This is very useful for improving the performance of
ftrace and livepatch.
If more than one callback is registered to a function, the general
trampoline is used, and the custom trampoline is not restored back to the
direct call even if all the other callbacks were unregistered and we are
back to one callback for the function.
To fix this, set FTRACE_FL_TRAMP flag if rec count is decremented
to one, and the ops that left has a trampoline.
Testing After this patch :
insmod livepatch_unshare_files.ko
cat /sys/kernel/debug/tracing/enabled_functions
unshare_files (1) R I tramp: 0xffffffffc0000000(klp_ftrace_handler+0x0/0xa0) ->ftrace_ops_assist_func+0x0/0xf0
echo unshare_files > /sys/kernel/debug/tracing/set_ftrace_filter
echo function > /sys/kernel/debug/tracing/current_tracer
cat /sys/kernel/debug/tracing/enabled_functions
unshare_files (2) R I ->ftrace_ops_list_func+0x0/0x150
echo nop > /sys/kernel/debug/tracing/current_tracer
cat /sys/kernel/debug/tracing/enabled_functions
unshare_files (1) R I tramp: 0xffffffffc0000000(klp_ftrace_handler+0x0/0xa0) ->ftrace_ops_assist_func+0x0/0xf0
Link: http://lkml.kernel.org/r/1556969979-111047-1-git-send-email-cj.chengjian@huawei.com
Signed-off-by: Cheng Jian <cj.chengjian@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The trace event self tests enable loop through *all* events, enables each
one, one at a time, runs some code to trigger various events (not
necessarily the same events), and checks if anything went wrong. The issue
is that trace events are usually the least likely start up test to cause a
problem, but they take the longest to run (because there are so many
events). When one of the other tests trigger a bug, the trace event start up
tests causes the bisect to take much longer, because it takes 10s of seconds
to get through the trace event tests.
By making them a separate config (even though they are enabled by default if
start up tests are set), it is possible to turn them off and still run the
other tracing start up tests much quicker.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add kprobe_event= boot parameter to define kprobe events
at boot time.
The definition syntax is similar to tracefs/kprobe_events
interface, but use ',' and ';' instead of ' ' and '\n'
respectively. e.g.
kprobe_event=p,vfs_read,$arg1,$arg2
This puts a probe on vfs_read with argument1 and 2, and
enable the new event.
Link: http://lkml.kernel.org/r/155851395498.15728.830529496248543583.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The comment of trace_filter_add_remove_task() refers to the function as
'trace_pid_filter_add_remove_task', use the correct name.
Link: http://lkml.kernel.org/r/20190523192628.134406-1-mka@chromium.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Support user-space dereference syntax for probe event arguments
to dereference the data-structure or array in user-space.
The syntax is just adding 'u' before an offset value.
+|-u<OFFSET>(<FETCHARG>)
e.g. +u8(%ax), +u0(+0(%si))
For example, if you probe do_sched_setscheduler(pid, policy,
param) and record param->sched_priority, you can add new
probe as below;
p do_sched_setscheduler priority=+u0($arg3)
Note that kprobe event provides this and it doesn't change the
dereference method automatically because we do not know whether
the given address is in userspace or kernel on some archs.
So as same as "ustring", this is an option for user, who has to
carefully choose the dereference method.
Link: http://lkml.kernel.org/r/155789872187.26965.4468456816590888687.stgit@devnote2
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add "ustring" type for fetching user-space string from kprobe event.
User can specify ustring type at uprobe event, and it is same as
"string" for uprobe.
Note that probe-event provides this option but it doesn't choose the
correct type automatically since we have not way to decide the address
is in user-space or not on some arch (and on some other arch, you can
fetch the string by "string" type). So user must carefully check the
target code (e.g. if you see __user on the target variable) and
use this new type.
Link: http://lkml.kernel.org/r/155789871009.26965.14167558859557329331.stgit@devnote2
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The code modification functions have "enable" and "update" variables that
are sometimes "int" but used as "bool". Remove the ambiguity and make them
"bool" when they are only used for true or false values.
Link: http://lkml.kernel.org/r/e1429923d9eda92a3cf5ee9e33c7eacce539781d.1558115654.git.naveen.n.rao@linux.vnet.ibm.com
Reported-by: "Naveen N. Rao" <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Starting with GCC 9, -Warray-bounds detects cases when memset is called
starting on a member of a struct but the size to be cleared ends up
writing over further members.
Such a call happens in the trace code to clear, at once, all members
after and including `seq` on struct trace_iterator:
In function 'memset',
inlined from 'ftrace_dump' at kernel/trace/trace.c:8914:3:
./include/linux/string.h:344:9: warning: '__builtin_memset' offset
[8505, 8560] from the object at 'iter' is out of the bounds of
referenced subobject 'seq' with type 'struct trace_seq' at offset
4368 [-Warray-bounds]
344 | return __builtin_memset(p, c, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
In order to avoid GCC complaining about it, we compute the address
ourselves by adding the offsetof distance instead of referring
directly to the member.
Since there are two places doing this clear (trace.c and trace_kdb.c),
take the chance to move the workaround into a single place in
the internal header.
Link: http://lkml.kernel.org/r/20190523124535.GA12931@gmail.com
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
[ Removed unnecessary parenthesis around "iter" ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
code and I forgot to incorporate them.
I also added a small clean up patch that was sent to me a while ago
and I just noticed it.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXOixqRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qlPsAQCmNzno+SJMXLLIojZ80pqs9PqLqIrW
iBopFNihRBAkxgEAle8Pvr53S4R/Hjn6j++kxBm/uWaEfICOzyqcSyqxlQA=
=Sin+
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Tom Zanussi sent me some small fixes and cleanups to the histogram
code and I forgot to incorporate them.
I also added a small clean up patch that was sent to me a while ago
and I just noticed it"
* tag 'trace-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
kernel/trace/trace.h: Remove duplicate header of trace_seq.h
tracing: Add a check_val() check before updating cond_snapshot() track_val
tracing: Check keys for variable references in expressions too
tracing: Prevent hist_field_var_ref() from accessing NULL tracing_map_elts
This patch tries to solve the following specific use case.
Currently, bpf program can already collect stack traces
through kernel function get_perf_callchain()
when certain events happens (e.g., cache miss counter or
cpu clock counter overflows). But such stack traces are
not enough for jitted programs, e.g., hhvm (jited php).
To get real stack trace, jit engine internal data structures
need to be traversed in order to get the real user functions.
bpf program itself may not be the best place to traverse
the jit engine as the traversing logic could be complex and
it is not a stable interface either.
Instead, hhvm implements a signal handler,
e.g. for SIGALARM, and a set of program locations which
it can dump stack traces. When it receives a signal, it will
dump the stack in next such program location.
Such a mechanism can be implemented in the following way:
. a perf ring buffer is created between bpf program
and tracing app.
. once a particular event happens, bpf program writes
to the ring buffer and the tracing app gets notified.
. the tracing app sends a signal SIGALARM to the hhvm.
But this method could have large delays and causing profiling
results skewed.
This patch implements bpf_send_signal() helper to send
a signal to hhvm in real time, resulting in intended stack traces.
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Without this check a snapshot is taken whenever a bucket's max is hit,
rather than only when the global max is hit, as it should be.
Before:
In this example, we do a first run of the workload (cyclictest),
examine the output, note the max ('triggering value') (347), then do
a second run and note the max again.
In this case, the max in the second run (39) is below the max in the
first run, but since we haven't cleared the histogram, the first max
is still in the histogram and is higher than any other max, so it
should still be the max for the snapshot. It isn't however - the
value should still be 347 after the second run.
# echo 'hist:keys=pid:ts0=common_timestamp.usecs if comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_waking/trigger
# echo 'hist:keys=next_pid:wakeup_lat=common_timestamp.usecs-$ts0:onmax($wakeup_lat).save(next_prio,next_comm,prev_pid,prev_prio,prev_comm):onmax($wakeup_lat).snapshot() if next_comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
# cyclictest -p 80 -n -s -t 2 -D 2
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/hist
{ next_pid: 2143 } hitcount: 199
max: 44 next_prio: 120 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/4
{ next_pid: 2145 } hitcount: 1325
max: 38 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/2
{ next_pid: 2144 } hitcount: 1982
max: 347 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/6
Snapshot taken (see tracing/snapshot). Details:
triggering value { onmax($wakeup_lat) }: 347
triggered by event with key: { next_pid: 2144 }
# cyclictest -p 80 -n -s -t 2 -D 2
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/hist
{ next_pid: 2143 } hitcount: 199
max: 44 next_prio: 120 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/4
{ next_pid: 2148 } hitcount: 199
max: 16 next_prio: 120 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/1
{ next_pid: 2145 } hitcount: 1325
max: 38 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/2
{ next_pid: 2150 } hitcount: 1326
max: 39 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/4
{ next_pid: 2144 } hitcount: 1982
max: 347 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/6
{ next_pid: 2149 } hitcount: 1983
max: 130 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/0
Snapshot taken (see tracing/snapshot). Details:
triggering value { onmax($wakeup_lat) }: 39
triggered by event with key: { next_pid: 2150 }
After:
In this example, we do a first run of the workload (cyclictest),
examine the output, note the max ('triggering value') (375), then do
a second run and note the max again.
In this case, the max in the second run is still 375, the highest in
any bucket, as it should be.
# cyclictest -p 80 -n -s -t 2 -D 2
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/hist
{ next_pid: 2072 } hitcount: 200
max: 28 next_prio: 120 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/5
{ next_pid: 2074 } hitcount: 1323
max: 375 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/2
{ next_pid: 2073 } hitcount: 1980
max: 153 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/6
Snapshot taken (see tracing/snapshot). Details:
triggering value { onmax($wakeup_lat) }: 375
triggered by event with key: { next_pid: 2074 }
# cyclictest -p 80 -n -s -t 2 -D 2
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/hist
{ next_pid: 2101 } hitcount: 199
max: 49 next_prio: 120 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/6
{ next_pid: 2072 } hitcount: 200
max: 28 next_prio: 120 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/5
{ next_pid: 2074 } hitcount: 1323
max: 375 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/2
{ next_pid: 2103 } hitcount: 1325
max: 74 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/4
{ next_pid: 2073 } hitcount: 1980
max: 153 next_prio: 19 next_comm: cyclictest
prev_pid: 0 prev_prio: 120 prev_comm: swapper/6
{ next_pid: 2102 } hitcount: 1981
max: 84 next_prio: 19 next_comm: cyclictest
prev_pid: 12 prev_prio: 120 prev_comm: kworker/0:1
Snapshot taken (see tracing/snapshot). Details:
triggering value { onmax($wakeup_lat) }: 375
triggered by event with key: { next_pid: 2074 }
Link: http://lkml.kernel.org/r/95958351329f129c07504b4d1769c47a97b70d65.1555597045.git.tom.zanussi@linux.intel.com
Cc: stable@vger.kernel.org
Fixes: a3785b7eca ("tracing: Add hist trigger snapshot() action")
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
There's an existing check for variable references in keys, but it
doesn't go far enough. It checks whether a key field is a variable
reference but doesn't check whether it's an expression containing
variable references, which can cause the same problems for callers.
Use the existing field_has_hist_vars() function rather than a direct
top-level flag check to catch all possible variable references.
Link: http://lkml.kernel.org/r/e8c3d3d53db5ca90ceea5a46e5413103a6902fc7.1555597045.git.tom.zanussi@linux.intel.com
Cc: stable@vger.kernel.org
Fixes: 067fe038e7 ("tracing: Add variable reference handling to hist triggers")
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
hist_field_var_ref() is an implementation of hist_field_fn_t(), which
can be called with a null tracing_map_elt elt param when assembling a
key in event_hist_trigger().
In the case of hist_field_var_ref() this doesn't make sense, because a
variable can only be resolved by looking it up using an already
assembled key i.e. a variable can't be used to assemble a key since
the key is required in order to access the variable.
Upper layers should prevent the user from constructing a key using a
variable in the first place, but in case one slips through, it
shouldn't cause a NULL pointer dereference. Also if one does slip
through, we want to know about it, so emit a one-time warning in that
case.
Link: http://lkml.kernel.org/r/64ec8dc15c14d305295b64cdfcc6b2b9dd14753f.1555597045.git.tom.zanussi@linux.intel.com
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
2) Fix TCP retransmission timestamps on passive Fast Open, from Yuchung
Cheng.
3) Orphan NFC, we'll take the patches directly into my tree. From
Johannes Berg.
4) We can't recycle cloned TCP skbs, from Eric Dumazet.
5) Some flow dissector bpf test fixes, from Stanislav Fomichev.
6) Fix RCU marking and warnings in rhashtable, from Herbert Xu.
7) Fix some potential fib6 leaks, from Eric Dumazet.
8) Fix a _decode_session4 uninitialized memory read bug fix that got
lost in a merge. From Florian Westphal.
9) Fix ipv6 source address routing wrt. exception route entries, from
Wei Wang.
10) The netdev_xmit_more() conversion was not done %100 properly in mlx5
driver, fix from Tariq Toukan.
11) Clean up botched merge on netfilter kselftest, from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (74 commits)
of_net: fix of_get_mac_address retval if compiled without CONFIG_OF
net: fix kernel-doc warnings for socket.c
net: Treat sock->sk_drops as an unsigned int when printing
kselftests: netfilter: fix leftover net/net-next merge conflict
mlxsw: core: Prevent reading unsupported slave address from SFP EEPROM
mlxsw: core: Prevent QSFP module initialization for old hardware
vsock/virtio: Initialize core virtio vsock before registering the driver
net/mlx5e: Fix possible modify header actions memory leak
net/mlx5e: Fix no rewrite fields with the same match
net/mlx5e: Additional check for flow destination comparison
net/mlx5e: Add missing ethtool driver info for representors
net/mlx5e: Fix number of vports for ingress ACL configuration
net/mlx5e: Fix ethtool rxfh commands when CONFIG_MLX5_EN_RXNFC is disabled
net/mlx5e: Fix wrong xmit_more application
net/mlx5: Fix peer pf disable hca command
net/mlx5: E-Switch, Correct type to u16 for vport_num and int for vport_index
net/mlx5: Add meaningful return codes to status_to_err function
net/mlx5: Imply MLXFW in mlx5_core
Revert "tipc: fix modprobe tipc failed after switch order of device registration"
vsock/virtio: free packets during the socket release
...
Daniel Borkmann says:
====================
pull-request: bpf 2019-05-16
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a use after free in __dev_map_entry_free(), from Eric.
2) Several sockmap related bug fixes: a splat in strparser if
it was never initialized, remove duplicate ingress msg list
purging which can race, fix msg->sg.size accounting upon
skb to msg conversion, and last but not least fix a timeout
bug in tcp_bpf_wait_data(), from John.
3) Fix LRU map to avoid messing with eviction heuristics upon
syscall lookup, e.g. map walks from user space side will
then lead to eviction of just recently created entries on
updates as it would mark all map entries, from Daniel.
4) Don't bail out when libbpf feature probing fails. Also
various smaller fixes to flow_dissector test, from Stanislav.
5) Fix missing brackets for BTF_INT_OFFSET() in UAPI, from Gary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removing of non-DYNAMIC_FTRACE from 32bit x86
- Removing of mcount support from x86
- Emulating a call from int3 on x86_64, fixes live kernel patching
- Consolidated Tracing Error logs file
Minor updates:
- Removal of klp_check_compiler_support()
- kdb ftrace dumping output changes
- Accessing and creating ftrace instances from inside the kernel
- Clean up of #define if macro
- Introduction of TRACE_EVENT_NOP() to disable trace events based on config
options
And other minor fixes and clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXNxMZxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qq4PAP44kP6VbwL8CHyI2A3xuJ6Hwxd+2Z2r
ip66RtzyJ+2iCgEA2QCuWUlEt2bLpF9a8IQ4N9tWenSeW2i7gunPb+tioQw=
=RVQo
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The major changes in this tracing update includes:
- Removal of non-DYNAMIC_FTRACE from 32bit x86
- Removal of mcount support from x86
- Emulating a call from int3 on x86_64, fixes live kernel patching
- Consolidated Tracing Error logs file
Minor updates:
- Removal of klp_check_compiler_support()
- kdb ftrace dumping output changes
- Accessing and creating ftrace instances from inside the kernel
- Clean up of #define if macro
- Introduction of TRACE_EVENT_NOP() to disable trace events based on
config options
And other minor fixes and clean ups"
* tag 'trace-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (44 commits)
x86: Hide the int3_emulate_call/jmp functions from UML
livepatch: Remove klp_check_compiler_support()
ftrace/x86: Remove mcount support
ftrace/x86_32: Remove support for non DYNAMIC_FTRACE
tracing: Simplify "if" macro code
tracing: Fix documentation about disabling options using trace_options
tracing: Replace kzalloc with kcalloc
tracing: Fix partial reading of trace event's id file
tracing: Allow RCU to run between postponed startup tests
tracing: Fix white space issues in parse_pred() function
tracing: Eliminate const char[] auto variables
ring-buffer: Fix mispelling of Calculate
tracing: probeevent: Fix to make the type of $comm string
tracing: probeevent: Do not accumulate on ret variable
tracing: uprobes: Re-enable $comm support for uprobe events
ftrace/x86_64: Emulate call function while updating in breakpoint handler
x86_64: Allow breakpoints to emulate call instructions
x86_64: Add gap to int3 to allow for call emulation
tracing: kdb: Allow ftdump to skip all but the last few entries
tracing: Add trace_total_entries() / trace_total_entries_cpu()
...
Both of them are not declared in the headers and not used outside
of bpf_trace.c file.
Fixes: a38d1107f9 ("bpf: support raw tracepoints in modules")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to
be handled consistently. Unsurprisingly, we enforce the lines to
be either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone
does, so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed.
Such nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs
and outputs at the same time and after improving the MMIO library
we handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM
work as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update.
-----BEGIN PGP SIGNATURE-----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=rhto
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
To disable a tracing option using the trace_options file, the option
name needs to be prefixed with 'no', and not suffixed, as the README
states. Fix it.
Link: http://lkml.kernel.org/r/154872690031.47356.5739053380942044586.stgit@srivatsa-ubuntu
Signed-off-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Replace kzalloc() function with its 2-factor argument form, kcalloc().
This patch replaces cases of:
kzalloc(a * b, gfp)
with:
kcalloc(a, b, gfp)
This code was detected with the help of Coccinelle.
Link: http://lkml.kernel.org/r/20190115043408.GA23456@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When reading only part of the id file, the ppos isn't tracked correctly.
This is taken care by simple_read_from_buffer.
Reading a single byte, and then the next byte would result EOF.
While this seems like not a big deal, this breaks abstractions that
reads information from files unbuffered. See for example
https://github.com/golang/go/issues/29399
This code was mentioned as problematic in
commit cd458ba9d5
("tracing: Do not (ab)use trace_seq in event_id_read()")
An example C code that show this bug is:
#include <stdio.h>
#include <stdint.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
int main(int argc, char **argv) {
if (argc < 2)
return 1;
int fd = open(argv[1], O_RDONLY);
char c;
read(fd, &c, 1);
printf("First %c\n", c);
read(fd, &c, 1);
printf("Second %c\n", c);
}
Then run with, e.g.
sudo ./a.out /sys/kernel/debug/tracing/events/tcp/tcp_set_state/id
You'll notice you're getting the first character twice, instead of the
first two characters in the id file.
Link: http://lkml.kernel.org/r/20181231115837.4932-1-elazar@lightbitslabs.com
Cc: Orit Wasserman <orit.was@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 23725aeeab ("ftrace: provide an id file for each event")
Signed-off-by: Elazar Leibovich <elazar@lightbitslabs.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When building a allmodconfig kernel for arm64 and boot that in qemu,
CONFIG_FTRACE_STARTUP_TEST gets enabled and that takes time so the
watchdog expires and prints out a message like this:
'watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [swapper/0:1]'
Depending on what the what test gets called from init_trace_selftests()
it stays minutes in the loop.
Rework so that function cond_resched() gets called in the
init_trace_selftests loop.
Link: http://lkml.kernel.org/r/20181130145622.26334-1-anders.roxell@linaro.org
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Trivial fix to clean up an indentation issue, a whole chunk of code
has an extra space in the indentation.
Link: http://lkml.kernel.org/r/20181109132312.20994-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Automatic const char[] variables cause unnecessary code
generation. For example, the this_mod variable leads to
3f04: 48 b8 5f 5f 74 68 69 73 5f 6d movabs $0x6d5f736968745f5f,%rax # __this_m
3f0e: 4c 8d 44 24 02 lea 0x2(%rsp),%r8
3f13: 48 8d 7c 24 10 lea 0x10(%rsp),%rdi
3f18: 48 89 44 24 02 mov %rax,0x2(%rsp)
3f1d: 4c 89 e9 mov %r13,%rcx
3f20: b8 65 00 00 00 mov $0x65,%eax # e
3f25: 48 c7 c2 00 00 00 00 mov $0x0,%rdx
3f28: R_X86_64_32S .rodata.str1.1+0x18d
3f2c: be 48 00 00 00 mov $0x48,%esi
3f31: c7 44 24 0a 6f 64 75 6c movl $0x6c75646f,0xa(%rsp) # odul
3f39: 66 89 44 24 0e mov %ax,0xe(%rsp)
i.e., the string gets built on the stack at runtime. Similar code can be
found for the other instances I'm replacing here. Putting the string
in .rodata reduces the combined .text+.rodata size and saves time and
stack space at runtime.
The simplest fix, and what I've done for the this_mod case, is to just
make the variable static.
However, for the "<faulted>" case where the same string is used twice,
that prevents the linker from merging those two literals, so instead use
a macro - that also keeps the two instances automatically in
sync (instead of only the compile-time strlen expression).
Finally, for the two runs of spaces, it turns out that the "build
these strings on the stack" is not the worst part of what gcc does -
it turns print_func_help_header_irq() into "if (tgid) { /*
print_event_info + five seq_printf calls */ } else { /* print
event_info + another five seq_printf */}". Taking inspiration from a
suggestion from Al Viro, use %.*s to make snprintf either stop after
the first two spaces or print the whole string. As a bonus, the
seq_printfs now fit on single lines (at least, they are not longer
than the existing ones in the function just above), making it easier
to see that the ascii art lines up.
x86-64 defconfig + CONFIG_FUNCTION_TRACER:
$ scripts/stackdelta /tmp/stackusage.{0,1}
./kernel/trace/ftrace.c ftrace_mod_callback 152 136 -16
./kernel/trace/trace.c trace_default_header 56 32 -24
./kernel/trace/trace.c tracing_mark_raw_write 96 72 -24
./kernel/trace/trace.c tracing_mark_write 104 80 -24
bloat-o-meter
add/remove: 1/0 grow/shrink: 0/4 up/down: 14/-375 (-361)
Function old new delta
this_mod - 14 +14
ftrace_mod_callback 577 542 -35
tracing_mark_raw_write 444 374 -70
tracing_mark_write 616 540 -76
trace_default_header 600 406 -194
Link: http://lkml.kernel.org/r/20190320081757.6037-1-linux@rasmusvillemoes.dk
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix to make the type of $comm "string". If we set the other type to $comm
argument, it shows meaningless value or wrong data. Currently probe events
allow us to set string array type (e.g. ":string[2]"), or other digit types
like x8 on $comm. But since clearly $comm is just a string data, it should
not be fetched by other types including array.
Link: http://lkml.kernel.org/r/155723736241.9149.14582064184468574539.stgit@devnote2
Cc: Andreas Ziegler <andreas.ziegler@fau.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 533059281e ("tracing: probeevent: Introduce new argument fetching code")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Do not accumulate strlen result on "ret" local variable, because
it is accumulated on "total" local variable for array case.
Link: http://lkml.kernel.org/r/155723735237.9149.3192150444705457531.stgit@devnote2
Fixes: 40b53b7718 ("tracing: probeevent: Add array type support")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Since commit 533059281e ("tracing: probeevent: Introduce new
argument fetching code") dropped the $comm support from uprobe
events, this re-enables it.
For $comm support, uses strlcpy() instead of strncpy_from_user()
to copy current task's comm. Because it is in the kernel space,
strncpy_from_user() always fails to copy the comm.
This also uses strlen() instead of strnlen_user() to measure the
length of the comm.
Note that this uses -ECOMM as a token value to fetch the comm
string. If the user-space pointer points -ECOMM, it will be
translated to task->comm.
Link: http://lkml.kernel.org/r/155723734162.9149.4042756162201097965.stgit@devnote2
Fixes: 533059281e ("tracing: probeevent: Introduce new argument fetching code")
Reported-by: Andreas Ziegler <andreas.ziegler@fau.de>
Acked-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Pull x86 mm updates from Ingo Molnar:
"The changes in here are:
- text_poke() fixes and an extensive set of executability lockdowns,
to (hopefully) eliminate the last residual circumstances under
which we are using W|X mappings even temporarily on x86 kernels.
This required a broad range of surgery in text patching facilities,
module loading, trampoline handling and other bits.
- tweak page fault messages to be more informative and more
structured.
- remove DISCONTIGMEM support on x86-32 and make SPARSEMEM the
default.
- reduce KASLR granularity on 5-level paging kernels from 512 GB to
1 GB.
- misc other changes and updates"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/mm: Initialize PGD cache during mm initialization
x86/alternatives: Add comment about module removal races
x86/kprobes: Use vmalloc special flag
x86/ftrace: Use vmalloc special flag
bpf: Use vmalloc special flag
modules: Use vmalloc special flag
mm/vmalloc: Add flag for freeing of special permsissions
mm/hibernation: Make hibernation handle unmapped pages
x86/mm/cpa: Add set_direct_map_*() functions
x86/alternatives: Remove the return value of text_poke_*()
x86/jump-label: Remove support for custom text poker
x86/modules: Avoid breaking W^X while loading modules
x86/kprobes: Set instruction page as executable
x86/ftrace: Set trampoline pages as executable
x86/kgdb: Avoid redundant comparison of patched code
x86/alternatives: Use temporary mm for text poking
x86/alternatives: Initialize temporary mm for patching
fork: Provide a function for copying init_mm
uprobes: Initialize uprobes earlier
x86/mm: Save debug registers when loading a temporary mm
...
Pull stack trace updates from Ingo Molnar:
"So Thomas looked at the stacktrace code recently and noticed a few
weirdnesses, and we all know how such stories of crummy kernel code
meeting German engineering perfection end: a 45-patch series to clean
it all up! :-)
Here's the changes in Thomas's words:
'Struct stack_trace is a sinkhole for input and output parameters
which is largely pointless for most usage sites. In fact if embedded
into other data structures it creates indirections and extra storage
overhead for no benefit.
Looking at all usage sites makes it clear that they just require an
interface which is based on a storage array. That array is either on
stack, global or embedded into some other data structure.
Some of the stack depot usage sites are outright wrong, but
fortunately the wrongness just causes more stack being used for
nothing and does not have functional impact.
Another oddity is the inconsistent termination of the stack trace
with ULONG_MAX. It's pointless as the number of entries is what
determines the length of the stored trace. In fact quite some call
sites remove the ULONG_MAX marker afterwards with or without nasty
comments about it. Not all architectures do that and those which do,
do it inconsistenly either conditional on nr_entries == 0 or
unconditionally.
The following series cleans that up by:
1) Removing the ULONG_MAX termination in the architecture code
2) Removing the ULONG_MAX fixups at the call sites
3) Providing plain storage array based interfaces for stacktrace
and stackdepot.
4) Cleaning up the mess at the callsites including some related
cleanups.
5) Removing the struct stack_trace based interfaces
This is not changing the struct stack_trace interfaces at the
architecture level, but it removes the exposure to the generic
code'"
* 'core-stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
x86/stacktrace: Use common infrastructure
stacktrace: Provide common infrastructure
lib/stackdepot: Remove obsolete functions
stacktrace: Remove obsolete functions
livepatch: Simplify stack trace retrieval
tracing: Remove the last struct stack_trace usage
tracing: Simplify stack trace retrieval
tracing: Make ftrace_trace_userstack() static and conditional
tracing: Use percpu stack trace buffer more intelligently
tracing: Simplify stacktrace retrieval in histograms
lockdep: Simplify stack trace handling
lockdep: Remove save argument from check_prev_add()
lockdep: Remove unused trace argument from print_circular_bug()
drm: Simplify stacktrace handling
dm persistent data: Simplify stack trace handling
dm bufio: Simplify stack trace retrieval
btrfs: ref-verify: Simplify stack trace retrieval
dma/debug: Simplify stracktrace retrieval
fault-inject: Simplify stacktrace retrieval
mm/page_owner: Simplify stack trace handling
...
Pull objtool updates from Ingo Molnar:
"This is a series from Peter Zijlstra that adds x86 build-time uaccess
validation of SMAP to objtool, which will detect and warn about the
following uaccess API usage bugs and weirdnesses:
- call to %s() with UACCESS enabled
- return with UACCESS enabled
- return with UACCESS disabled from a UACCESS-safe function
- recursive UACCESS enable
- redundant UACCESS disable
- UACCESS-safe disables UACCESS
As it turns out not leaking uaccess permissions outside the intended
uaccess functionality is hard when the interfaces are complex and when
such bugs are mostly dormant.
As a bonus we now also check the DF flag. We had at least one
high-profile bug in that area in the early days of Linux, and the
checking is fairly simple. The checks performed and warnings emitted
are:
- call to %s() with DF set
- return with DF set
- return with modified stack frame
- recursive STD
- redundant CLD
It's all x86-only for now, but later on this can also be used for PAN
on ARM and objtool is fairly cross-platform in principle.
While all warnings emitted by this new checking facility that got
reported to us were fixed, there might be GCC version dependent
warnings that were not reported yet - which we'll address, should they
trigger.
The warnings are non-fatal build warnings"
* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
mm/uaccess: Use 'unsigned long' to placate UBSAN warnings on older GCC versions
x86/uaccess: Dont leak the AC flag into __put_user() argument evaluation
sched/x86_64: Don't save flags on context switch
objtool: Add Direction Flag validation
objtool: Add UACCESS validation
objtool: Fix sibling call detection
objtool: Rewrite alt->skip_orig
objtool: Add --backtrace support
objtool: Rewrite add_ignores()
objtool: Handle function aliases
objtool: Set insn->func for alternatives
x86/uaccess, kcov: Disable stack protector
x86/uaccess, ftrace: Fix ftrace_likely_update() vs. SMAP
x86/uaccess, ubsan: Fix UBSAN vs. SMAP
x86/uaccess, kasan: Fix KASAN vs SMAP
x86/smap: Ditch __stringify()
x86/uaccess: Introduce user_access_{save,restore}()
x86/uaccess, signal: Fix AC=1 bloat
x86/uaccess: Always inline user_access_begin()
x86/uaccess, xen: Suppress SMAP warnings
...
The 'ftdump' command in kdb is currently a bit of a last resort, at
least if you have lots of traces turned on. It's going to print a
whole boatload of data out your serial port which is probably running
at 115200. This could easily take many, many minutes.
Usually you're most interested in what's at the _end_ of the ftrace
buffer, AKA what happened most recently. That means you've got to
wait the full time for the dump. The 'ftdump' command does attempt to
help you a little bit by allowing you to skip a fixed number of
entries. Unfortunately it provides no way for you to know how many
entries you should skip.
Let's do similar to python and allow you to use a negative number to
indicate that you want to skip all entries except the last few. This
allows you to quickly see what you want.
Note that we also change the printout in ftdump to print the
(positive) number of entries actually skipped since that could be
helpful to know when you've specified a negative skip count.
Link: http://lkml.kernel.org/r/20190319171206.97107-3-dianders@chromium.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
These two new exported functions will be used in a future patch by
kdb_ftdump() to quickly skip all but the last few trace entries.
Link: http://lkml.kernel.org/r/20190319171206.97107-2-dianders@chromium.org
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The things skipped by kdb's "ftdump" command when you pass it a
parameter has always been entries, not lines. The difference usually
doesn't matter but when the trace buffer has multi-line entries (like
a stack dump) it can matter.
Let's fix this both in the help text for ftdump and also in the local
variable names.
Link: http://lkml.kernel.org/r/20190319171206.97107-1-dianders@chromium.org
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When using a temporary mm, bpf_probe_write_user() should not be able to
write to user memory, since user memory addresses may be used to map
kernel memory. Detect these cases and fail bpf_probe_write_user() in
such cases.
Suggested-by: Jann Horn <jannh@google.com>
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-24-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It's only used in trace.c and there is absolutely no point in compiling it
in when user space stack traces are not supported.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: linux-mm@kvack.org
Cc: David Rientjes <rientjes@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: kasan-dev@googlegroups.com
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: iommu@lists.linux-foundation.org
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: David Sterba <dsterba@suse.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: linux-btrfs@vger.kernel.org
Cc: dm-devel@redhat.com
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: intel-gfx@lists.freedesktop.org
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: linux-arch@vger.kernel.org
Link: https://lkml.kernel.org/r/20190425094803.162400595@linutronix.de
The per cpu stack trace buffer usage pattern is odd at best. The buffer has
place for 512 stack trace entries on 64-bit and 1024 on 32-bit. When
interrupts or exceptions nest after the per cpu buffer was acquired the
stacktrace length is hardcoded to 8 entries. 512/1024 stack trace entries
in kernel stacks are unrealistic so the buffer is a complete waste.
Split the buffer into 4 nest levels, which are 128/256 entries per
level. This allows nesting contexts (interrupts, exceptions) to utilize the
cpu buffer for stack retrieval and avoids the fixed length allocation along
with the conditional execution pathes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: linux-mm@kvack.org
Cc: David Rientjes <rientjes@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: kasan-dev@googlegroups.com
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: iommu@lists.linux-foundation.org
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: David Sterba <dsterba@suse.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: linux-btrfs@vger.kernel.org
Cc: dm-devel@redhat.com
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: intel-gfx@lists.freedesktop.org
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: linux-arch@vger.kernel.org
Link: https://lkml.kernel.org/r/20190425094803.066064076@linutronix.de
- Remove the extra array member of stack_dump_trace[] along with the
ARRAY_SIZE - 1 initialization for struct stack_trace :: max_entries.
Both are historical leftovers of no value. The stack tracer never exceeds
the array and there is no extra storage requirement either.
- Make variables which are only used in trace_stack.c static.
- Simplify the enable/disable logic.
- Rename stack_trace_print() as it's using the stack_trace_ namespace. Free
the name up for stack trace related functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: linux-mm@kvack.org
Cc: David Rientjes <rientjes@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: kasan-dev@googlegroups.com
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: iommu@lists.linux-foundation.org
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: David Sterba <dsterba@suse.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: linux-btrfs@vger.kernel.org
Cc: dm-devel@redhat.com
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: intel-gfx@lists.freedesktop.org
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: linux-arch@vger.kernel.org
Link: https://lkml.kernel.org/r/20190425094801.230654524@linutronix.de
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-04-28
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Introduce BPF socket local storage map so that BPF programs can store
private data they associate with a socket (instead of e.g. separate hash
table), from Martin.
2) Add support for bpftool to dump BTF types. This is done through a new
`bpftool btf dump` sub-command, from Andrii.
3) Enable BPF-based flow dissector for skb-less eth_get_headlen() calls which
was currently not supported since skb was used to lookup netns, from Stanislav.
4) Add an opt-in interface for tracepoints to expose a writable context
for attached BPF programs, used here for NBD sockets, from Matt.
5) BPF xadd related arm64 JIT fixes and scalability improvements, from Daniel.
6) Change the skb->protocol for bpf_skb_adjust_room() helper in order to
support tunnels such as sit. Add selftests as well, from Willem.
7) Various smaller misc fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an opt-in interface that allows a tracepoint to provide a safe
buffer that can be written from a BPF_PROG_TYPE_RAW_TRACEPOINT program.
The size of the buffer must be a compile-time constant, and is checked
before allowing a BPF program to attach to a tracepoint that uses this
feature.
The pointer to this buffer will be the first argument of tracepoints
that opt in; the pointer is valid and can be bpf_probe_read() by both
BPF_PROG_TYPE_RAW_TRACEPOINT and BPF_PROG_TYPE_RAW_TRACEPOINT_WRITABLE
programs that attach to such a tracepoint, but the buffer to which it
points may only be written by the latter.
Signed-off-by: Matt Mullins <mmullins@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- Use "nosteal" for ring buffer splice pages
- Memory leak fix in error path of trace_pid_write()
- Fix preempt_enable_no_resched() (use preempt_enable()) in ring buffer code
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXMMoghQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qmB1AQDfpVxYxcmxibBBAM6fZyILYpKqDWmy
ut6gHZ+GHhQT4AEAwSRsC6V4yO3d5dJFpkcQXUj1v+Ip9XU+dv//s8O6tAI=
=LsG/
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Three tracing fixes:
- Use "nosteal" for ring buffer splice pages
- Memory leak fix in error path of trace_pid_write()
- Fix preempt_enable_no_resched() (use preempt_enable()) in ring
buffer code"
* tag 'trace-v5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
trace: Fix preempt_enable_no_resched() abuse
tracing: Fix a memory leak by early error exit in trace_pid_write()
tracing: Fix buffer_ref pipe ops
Unless the very next line is schedule(), or implies it, one must not use
preempt_enable_no_resched(). It can cause a preemption to go missing and
thereby cause arbitrary delays, breaking the PREEMPT=y invariant.
Link: http://lkml.kernel.org/r/20190423200318.GY14281@hirez.programming.kicks-ass.net
Cc: Waiman Long <longman@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: the arch/x86 maintainers <x86@kernel.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: huang ying <huang.ying.caritas@gmail.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: stable@vger.kernel.org
Fixes: 2c2d7329d8 ("tracing/ftrace: use preempt_enable_no_resched_notrace in ring_buffer_time_stamp()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
In trace_pid_write(), the buffer for trace parser is allocated through
kmalloc() in trace_parser_get_init(). Later on, after the buffer is used,
it is then freed through kfree() in trace_parser_put(). However, it is
possible that trace_pid_write() is terminated due to unexpected errors,
e.g., ENOMEM. In that case, the allocated buffer will not be freed, which
is a memory leak bug.
To fix this issue, free the allocated buffer when an error is encountered.
Link: http://lkml.kernel.org/r/1555726979-15633-1-git-send-email-wang6495@umn.edu
Fixes: f4d34a87e9 ("tracing: Use pid bitmap instead of a pid array for set_event_pid")
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This fixes multiple issues in buffer_pipe_buf_ops:
- The ->steal() handler must not return zero unless the pipe buffer has
the only reference to the page. But generic_pipe_buf_steal() assumes
that every reference to the pipe is tracked by the page's refcount,
which isn't true for these buffers - buffer_pipe_buf_get(), which
duplicates a buffer, doesn't touch the page's refcount.
Fix it by using generic_pipe_buf_nosteal(), which refuses every
attempted theft. It should be easy to actually support ->steal, but the
only current users of pipe_buf_steal() are the virtio console and FUSE,
and they also only use it as an optimization. So it's probably not worth
the effort.
- The ->get() and ->release() handlers can be invoked concurrently on pipe
buffers backed by the same struct buffer_ref. Make them safe against
concurrency by using refcount_t.
- The pointers stored in ->private were only zeroed out when the last
reference to the buffer_ref was dropped. As far as I know, this
shouldn't be necessary anyway, but if we do it, let's always do it.
Link: http://lkml.kernel.org/r/20190404215925.253531-1-jannh@google.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Fixes: 73a757e631 ("ring-buffer: Return reader page back into existing ring buffer")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-04-22
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) allow stack/queue helpers from more bpf program types, from Alban.
2) allow parallel verification of root bpf programs, from Alexei.
3) introduce bpf sysctl hook for trusted root cases, from Andrey.
4) recognize var/datasec in btf deduplication, from Andrii.
5) cpumap performance optimizations, from Jesper.
6) verifier prep for alu32 optimization, from Jiong.
7) libbpf xsk cleanup, from Magnus.
8) other various fixes and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function_graph boot up self test emulates the tr->init() function in
order to add a wrapper around the function graph tracer entry code to test
for lock ups and such. But it does not emulate the tr->reset(), and just
calls the function_graph tracer tr->reset() function which will use its own
fgraph_ops to unregister function tracing with. As the fgraph_ops is
becoming more meaningful with the register_ftrace_graph() and
unregister_ftrace_graph() functions, the two need to be the same. The
emulated tr->init() uses its own fgraph_ops descriptor, which means the
unregister_ftrace_graph() must use the same ftrace_ops, which the selftest
currently does not do. By emulating the tr->reset() as the selftest does
with the tr->init() it will be able to pass the same fgraph_ops descriptor
to the unregister_ftrace_graph() as it did with the register_ftrace_graph().
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
commit f1a2e44a3a ("bpf: add queue and stack maps") introduced new BPF
helper functions:
- BPF_FUNC_map_push_elem
- BPF_FUNC_map_pop_elem
- BPF_FUNC_map_peek_elem
but they were made available only for network BPF programs. This patch
makes them available for tracepoint, cgroup and lirc programs.
Signed-off-by: Alban Crequy <alban@kinvolk.io>
Cc: Mauricio Vasquez B <mauricio.vasquez@polito.it>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Merge page ref overflow branch.
Jann Horn reported that he can overflow the page ref count with
sufficient memory (and a filesystem that is intentionally extremely
slow).
Admittedly it's not exactly easy. To have more than four billion
references to a page requires a minimum of 32GB of kernel memory just
for the pointers to the pages, much less any metadata to keep track of
those pointers. Jann needed a total of 140GB of memory and a specially
crafted filesystem that leaves all reads pending (in order to not ever
free the page references and just keep adding more).
Still, we have a fairly straightforward way to limit the two obvious
user-controllable sources of page references: direct-IO like page
references gotten through get_user_pages(), and the splice pipe page
duplication. So let's just do that.
* branch page-refs:
fs: prevent page refcount overflow in pipe_buf_get
mm: prevent get_user_pages() from overflowing page refcount
mm: add 'try_get_page()' helper function
mm: make page ref count overflow check tighter and more explicit
No architecture terminates the stack trace with ULONG_MAX anymore. As the
code checks the number of entries stored anyway there is no point in
keeping all that ULONG_MAX magic around.
The histogram code zeroes the storage before saving the stack, so if the
trace is shorter than the maximum number of entries it can terminate the
print loop if a zero entry is detected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Potapenko <glider@google.com>
Link: https://lkml.kernel.org/r/20190410103645.048761764@linutronix.de
Change pipe_buf_get() to return a bool indicating whether it succeeded
in raising the refcount of the page (if the thing in the pipe is a page).
This removes another mechanism for overflowing the page refcount. All
callers converted to handle a failure.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function_graph tracer has a stub function and its ops flag has the
FTRACE_OPS_FL_STUB set. As the function graph does not use the
ftrace_ops->func pointer but instead is called by a separate part of the
ftrace trampoline. The function_graph tracer still requires to pass in a
ftrace_ops that may also hold the hash of the functions to call. But there's
no reason to test that hash in the function tracing portion. Instead of
testing to see if we should call the stub function, just test if the ops has
FTRACE_OPS_FL_STUB set, and just skip it.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The ASSIGN_OPS_HASH() macro was moved to fgraph.c where it was used, but for
some reason it wasn't removed from ftrace.c, as it is no longer referenced
there.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As each instance has their own error_log file, it makes more sense that the
instances show the errors of their own instead of all error_logs having the
same data. Make it that the errors show up in the instance error_log file
that the error happens in. If no instance trace_array is available, then
NULL can be passed in which will create the error in the top level instance
(the one at the top of the tracefs directory).
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Tested-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Have the trace_array that associates the trace instance of the histogram
passed around to functions so that error handling can display the error
message in the proper instance.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Tested-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pass in the trace_array that represents the instance the filter being
changed is in to create_event_filter(). This will allow for error messages
that happen when writing to the filter can be displayed in the proper
instance "error_log" file.
Note, for calls to create_filter() (that was also modified to support
create_event_filter()), that changes filters that do not exist in a instance
(for perf for example), NULL may be passed in, which means that there will
not be any message to log for that filter.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Tested-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
gpio tracing was made configurable in 4.4-rc1 (commit ddd70280bf
("tracing: gpio: Add Kconfig option for enabling/disabling trace
events")). Since then it is the only event type that can be compiled
conditionally. Given that there is only little overhead I don't
understand the reasoning and I was annoyed more than once that gpio
events were not available without recompiling.
So drop the Kconfig symbol and make gpio events available
unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only users that calls syscall_get_arguments() with a variable and not a
hard coded '6' is ftrace_syscall_enter(). syscall_get_arguments() can be
optimized by removing a variable input, and always grabbing 6 arguments
regardless of what the system call actually uses.
Change ftrace_syscall_enter() to pass the 6 args into a local stack array
and copy the necessary arguments into the trace event as needed.
This is needed to remove two parameters from syscall_get_arguments().
Link: http://lkml.kernel.org/r/20161107213233.627583542@goodmis.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
For CONFIG_TRACE_BRANCH_PROFILING=y the likely/unlikely things get
overloaded and generate callouts to this code, and thus also when
AC=1.
Make it safe.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use tracing error_log with probe events for logging error more
precisely. This also makes all parse error returns -EINVAL
(except for -ENOMEM), because user can see better error message
in error_log file now.
Link: http://lkml.kernel.org/r/6a4d90e141d138040ea61f4776b991597077451e.1554072478.git.tom.zanussi@linux.intel.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Use tracing_log_err() from the new tracing error_log mechanism to send
filter parse errors to tracing/error_log.
With this change, users will be able to see filter errors by looking
at tracing/error_log.
The same errors will also be available in the filter file, as
expected.
Link: http://lkml.kernel.org/r/1d942c419941539a11d78a6810fc5740a99b2974.1554072478.git.tom.zanussi@linux.intel.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Replace hist_err() and hist_err_event() with tracing_log_err() from
the new tracing error_log mechanism.
Also add a couple related helper functions and remove most of the old
hist_err()-related code.
With this change, users no longer read the hist files for hist trigger
error information, but instead look at tracing/error_log for the same
information.
Link: http://lkml.kernel.org/r/c98f77a97c9715d18b623eeb5741057b330d5ac0.1554072478.git.tom.zanussi@linux.intel.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
In preparation for making use of the new trace error log, save the
subsystem and event name associated with the last hist command - it
will be passed as the location param in the event_log_err() calls.
Link: http://lkml.kernel.org/r/eb0fd1362be8f39facb86c83eecf441b7a5876f8.1554072478.git.tom.zanussi@linux.intel.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Introduce a new ftrace file, tracing/error_log, for ftrace commands to
log errors. This is useful for allowing more complex commands such as
hist trigger and kprobe_event commands to point out specifically where
something may have gone wrong without forcing them to resort to more
ad hoc methods such as tacking error messages onto existing output
files.
To log a tracing error, call the event_log_err() function, passing it
a location string describing where it came from e.g. kprobe_events or
system:event, the command that caused the error, an array of static
error strings describing errors and an index within that array which
describes the specific error, along with the position to place the
error caret.
Reading the log displays the last (currently) 8 errors logged in the
following format:
[timestamp] <loc>: error: <static error text>
Command: <command that caused the error>
^
Memory for the error log isn't allocated unless there has been a trace
event error, and the error log can be cleared and have its memory
freed by writing the empty string in truncation mode to it:
# echo > tracing/error_log.
Link: http://lkml.kernel.org/r/0c2c82571fd38c5f3a88ca823627edff250e9416.1554072478.git.tom.zanussi@linux.intel.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Improvements-suggested-by: Steve Rostedt <rostedt@goodmis.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Ftrace provides the feature “instances” that provides the capability to
create multiple Ftrace ring buffers. However, currently these buffers
are created/accessed via userspace only. The kernel APIs providing these
features are not exported, hence cannot be used by other kernel
components.
This patch aims to extend this infrastructure to provide the
flexibility to create/log/remove/ enable-disable existing trace events
to these buffers from within the kernel.
Link: http://lkml.kernel.org/r/1553106531-3281-2-git-send-email-divya.indi@oracle.com
Signed-off-by: Divya Indi <divya.indi@oracle.com>
Reviewed-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix compile warning in create_dyn_event(): 'ret' may be used uninitialized
in this function [-Wuninitialized].
Link: http://lkml.kernel.org/r/1553237900-8555-1-git-send-email-frowand.list@gmail.com
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Fixes: 5448d44c38 ("tracing: Add unified dynamic event framework")
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
-----BEGIN PGP SIGNATURE-----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=qBae
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
error checks.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXIukmxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qi+PAQCKf6Yz7LZ3oBtjKy7jJRhkAn3Ie5Ls
n7KOXnOGntO1cgD/RdynJcFtpwgDxuj7L/c3iInel0B/rdU5VLbglXy+2AA=
=y/ft
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes and cleanups from Steven Rostedt:
"This contains a series of last minute clean ups, small fixes and error
checks"
* tag 'trace-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/probe: Verify alloc_trace_*probe() result
tracing/probe: Check event/group naming rule at parsing
tracing/probe: Check the size of argument name and body
tracing/probe: Check event name length correctly
tracing/probe: Check maxactive error cases
tracing: kdb: Fix ftdump to not sleep
trace/probes: Remove kernel doc style from non kernel doc comment
tracing/probes: Make reserved_field_names static
Since alloc_trace_*probe() returns -EINVAL only if !event && !group,
it should not happen in trace_*probe_create(). If we catch that case
there is a bug. So use WARN_ON_ONCE() instead of pr_info().
Link: http://lkml.kernel.org/r/155253785078.14922.16902223633734601469.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Ensure given name of event is not too long when parsing it,
and fix to update event name offset correctly when the group
name is given. For example, this makes probe event to check
the "p:foo/" error case correctly.
Link: http://lkml.kernel.org/r/155253782046.14922.14724124823730168629.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Check maxactive on kprobe error case, because maxactive
is only for kretprobe, not for kprobe. Also, maxactive
should not be 0, it should be at least 1.
Link: http://lkml.kernel.org/r/155253780952.14922.15784129810238750331.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
this place in the code produced a warning (W=1).
This commit remove the following warning:
kernel/trace/blktrace.c:725:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As reported back in 2016-11 [1], the "ftdump" kdb command triggers a
BUG for "sleeping function called from invalid context".
kdb's "ftdump" command wants to call ring_buffer_read_prepare() in
atomic context. A very simple solution for this is to add allocation
flags to ring_buffer_read_prepare() so kdb can call it without
triggering the allocation error. This patch does that.
Note that in the original email thread about this, it was suggested
that perhaps the solution for kdb was to either preallocate the buffer
ahead of time or create our own iterator. I'm hoping that this
alternative of adding allocation flags to ring_buffer_read_prepare()
can be considered since it means I don't need to duplicate more of the
core trace code into "trace_kdb.c" (for either creating my own
iterator or re-preparing a ring allocator whose memory was already
allocated).
NOTE: another option for kdb is to actually figure out how to make it
reuse the existing ftrace_dump() function and totally eliminate the
duplication. This sounds very appealing and actually works (the "sr
z" command can be seen to properly dump the ftrace buffer). The
downside here is that ftrace_dump() fully consumes the trace buffer.
Unless that is changed I'd rather not use it because it means "ftdump
| grep xyz" won't be very useful to search the ftrace buffer since it
will throw away the whole trace on the first grep. A future patch to
dump only the last few lines of the buffer will also be hard to
implement.
[1] https://lkml.kernel.org/r/20161117191605.GA21459@google.com
Link: http://lkml.kernel.org/r/20190308193205.213659-1-dianders@chromium.org
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull misc vfs updates from Al Viro:
"Assorted fixes (really no common topic here)"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: Make __vfs_write() static
vfs: fix preadv64v2 and pwritev64v2 compat syscalls with offset == -1
pipe: stop using ->can_merge
splice: don't merge into linked buffers
fs: move generic stat response attr handling to vfs_getattr_nosec
orangefs: don't reinitialize result_mask in ->getattr
fs/devpts: always delete dcache dentry-s in dput()
CC kernel/trace/trace_kprobe.o
kernel/trace/trace_kprobe.c:41: warning: cannot understand function prototype: 'struct trace_kprobe '
The real problem is that a comment looked like kerneldoc when it shouldn't be...
Link: http://lkml.kernel.org/r/2812.1552381112@turing-police
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
sparse complains:
CHECK kernel/trace/trace_probe.c
kernel/trace/trace_probe.c:16:12: warning: symbol 'reserved_field_names' was not declared. Should it be static?
Yes, it should be static.
Link: http://lkml.kernel.org/r/2478.1552380778@turing-police
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
- Add "onchange(var)" histogram handler that executes a action when $var
changes.
- Add new "snapshot()" action for histogram handlers, that causes a
snapshot of the ring buffer when triggered.
ie. onchange(var).snapshot() will trigger a snapshot if var changes.
- Add alternative for "trace()" action.
Currently, to trigger a synthetic event, the name of that event is used
as the handler name, which is inconsistent with the other actions.
onchange(var).synthetic(param) where it can now be
onchange(var).trace(synthetic, param). The older method will still be
allowed, as long as the synthetic events do not overlap with other
handler names.
- The histogram documentation at testcases were updated for the new
changes.
Added a quicker way to enable set_ftrace_filter files, that will make
it much quicker to bisect tracing a function that shouldn't be traced and
crashes the kernel. (You can echo in numbers to set_ftrace_filter, and it
will select the corresponding function that is in
available_filter_functions).
Some better displaying of the tracing data (and more information was added).
The rest are small fixes and more clean ups to the code.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXIXXjRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qrSJAQCbGXAvZE+shfKRhbU1cu1C1nwRMHhH
eeRecJs1RChGFgD/TwatD4FzARQPjfk7snQD5KWPpoRc9grUACC2cZcaWwQ=
=LVBI
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The biggest change for this release is in the histogram code:
- Add "onchange(var)" histogram handler that executes a action when
$var changes.
- Add new "snapshot()" action for histogram handlers, that causes a
snapshot of the ring buffer when triggered. ie.
onchange(var).snapshot() will trigger a snapshot if var changes.
- Add alternative for "trace()" action. Currently, to trigger a
synthetic event, the name of that event is used as the handler
name, which is inconsistent with the other actions.
onchange(var).synthetic(param) where it can now be
onchange(var).trace(synthetic, param). The older method will still
be allowed, as long as the synthetic events do not overlap with
other handler names.
- The histogram documentation at testcases were updated for the new
changes.
Outside of the histogram code, we have:
- Added a quicker way to enable set_ftrace_filter files, that will
make it much quicker to bisect tracing a function that shouldn't be
traced and crashes the kernel. (You can echo in numbers to
set_ftrace_filter, and it will select the corresponding function
that is in available_filter_functions).
- Some better displaying of the tracing data (and more information
was added).
The rest are small fixes and more clean ups to the code"
* tag 'trace-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (37 commits)
tracing: Use strncpy instead of memcpy when copying comm in trace.c
tracing: Use strncpy instead of memcpy when copying comm for hist triggers
tracing: Use strncpy instead of memcpy for string keys in hist triggers
tracing: Use str_has_prefix() in synth_event_create()
x86/ftrace: Fix warning and considate ftrace_jmp_replace() and ftrace_call_replace()
tracing/perf: Use strndup_user() instead of buggy open-coded version
doc: trace: Fix documentation for uprobe_profile
tracing: Fix spelling mistake: "analagous" -> "analogous"
tracing: Comment why cond_snapshot is checked outside of max_lock protection
tracing: Add hist trigger action 'expected fail' test case
tracing: Add alternative synthetic event trace action test case
tracing: Add hist trigger onchange() handler test case
tracing: Add hist trigger snapshot() action test case
tracing: Add SPDX license GPL-2.0 license identifier to inter-event testcases
tracing: Add alternative synthetic event trace action syntax
tracing: Add hist trigger onchange() handler Documentation
tracing: Add hist trigger onchange() handler
tracing: Add hist trigger snapshot() action Documentation
tracing: Add hist trigger snapshot() action
tracing: Add conditional snapshot
...
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module build
- allow to add optional flags to dpkg-buildpackage when building deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y9YG
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module
build
- allow to add optional flags to dpkg-buildpackage when building
deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
* tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (40 commits)
kbuild: remove scripts/basic/% build target
kbuild: use -Werror=implicit-... instead of -Werror-implicit-...
kbuild: clean up scripts/gcc-version.sh
kbuild: remove cc-version macro
kbuild: update comment block of scripts/clang-version.sh
kbuild: remove commented-out INITRD_COMPRESS
kbuild: move -gsplit-dwarf, -gdwarf-4 option tests to Kconfig
kbuild: [bin]deb-pkg: add DPKG_FLAGS variable
kbuild: move ".config not found!" message from Kconfig to Makefile
kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing
kbuild: simplify single target rules
kbuild: remove empty rules for makefiles
kbuild: make -r/-R effective in top Makefile for old Make versions
kbuild: move tools_silent to a more relevant place
kbuild: compute false-positive -Wmaybe-uninitialized cases in Kconfig
kbuild: refactor cc-cross-prefix implementation
kbuild: hardcode genksyms path and remove GENKSYMS variable
scripts/gdb: refactor rules for symlink creation
kbuild: create symlink to vmlinux-gdb.py in scripts_gdb target
scripts/gdb: do not descend into scripts/gdb from scripts
...
A small fix Pavel sent me back in august was accidentally lost due to it
being placed with some other patches that failed some tests, and was rebased
out of my local tree. Which was a regression that caused event filters
not to handle negative numbers.
The clean up is from Masami that realized that the code in kprobes that
calls probe_mem_read() wrapper, which is to be used in code used by both
kprobes and uprobes, was only in code for kprobes. It should not use the
wrapper there, but instead call probe_kernel_read() directly.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXH2gZRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qrTyAQC+dfxfyS32BWpGOwZbUIHGYYHtnpEB
7bIQzXy2q8r4YQD/UGJ0qoHur1gSMEIVjhIM0Qow4VepqqhthIAV/1iVbgU=
=F9yc
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.0-pre' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix/cleanup from Steven Rostedt:
"This is a "pre-pull". It's only one small fix and one small clean up.
I'm testing a few small patches for my real pull request which will
come at a later time. The second patch depends on your tree anyway so
I included it along with the urgent fix.
A small fix Pavel sent me back in august was accidentally lost due to
it being placed with some other patches that failed some tests, and
was rebased out of my local tree. Which was a regression that caused
event filters not to handle negative numbers.
The clean up is from Masami that realized that the code in kprobes
that calls probe_mem_read() wrapper, which is to be used in code used
by both kprobes and uprobes, was only in code for kprobes. It should
not use the wrapper there, but instead call probe_kernel_read()
directly"
* tag 'trace-v5.0-pre' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Use probe_kernel_read instead of probe_mem_read
tracing: Fix event filters and triggers to handle negative numbers
Because there may be random garbage beyond a string's null terminator,
code that might use the entire comm array e.g. histogram keys, can
give unexpected results if that garbage is copied in too, so avoid
that possibility by using strncpy instead of memcpy.
Link: http://lkml.kernel.org/r/1d6ebac26570c2a29ce9fb575379f17ef5c8b81b.1551802084.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Suggested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Because there may be random garbage beyond a string's null terminator,
code that might use the entire comm array e.g. histogram keys, can
give unexpected results if that garbage is copied in too, so avoid
that possibility by using strncpy instead of memcpy.
Link: http://lkml.kernel.org/r/1eb9f096a8086c3c82c7fc087c900005143cec54.1551802084.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Because there may be random garbage beyond a string's null terminator,
it's not correct to copy the the complete character array for use as a
hist trigger key. This results in multiple histogram entries for the
'same' string key.
So, in the case of a string key, use strncpy instead of memcpy to
avoid copying in the extra bytes.
Before, using the gdbus entries in the following hist trigger as an
example:
# echo 'hist:key=comm' > /sys/kernel/debug/tracing/events/sched/sched_waking/trigger
# cat /sys/kernel/debug/tracing/events/sched/sched_waking/hist
...
{ comm: ImgDecoder #4 } hitcount: 203
{ comm: gmain } hitcount: 213
{ comm: gmain } hitcount: 216
{ comm: StreamTrans #73 } hitcount: 221
{ comm: mozStorage #3 } hitcount: 230
{ comm: gdbus } hitcount: 233
{ comm: StyleThread#5 } hitcount: 253
{ comm: gdbus } hitcount: 256
{ comm: gdbus } hitcount: 260
{ comm: StyleThread#4 } hitcount: 271
...
# cat /sys/kernel/debug/tracing/events/sched/sched_waking/hist | egrep gdbus | wc -l
51
After:
# cat /sys/kernel/debug/tracing/events/sched/sched_waking/hist | egrep gdbus | wc -l
1
Link: http://lkml.kernel.org/r/50c35ae1267d64eee975b8125e151e600071d4dc.1549309756.git.tom.zanussi@linux.intel.com
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 79e577cbce ("tracing: Support string type key properly")
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cheng Jian