To be future-proof and for better readability the time comparisons are modified
to use time_before() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is otherwise a risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of raw math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function mlx4_en_set_channels() stops running ports before performing the
requested action. In that case local variable 'port_up' is set so that the
port is restarted at the end of the function, however, in case the port was
not stopped, variable 'port_up' is left uninitialized and the behaviour is
undetermined. Detected by Coverity - CID 751497.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the introduction of of_phy_register_fixed_link(), this patch
introduces fixed link support in the mvneta driver, for Marvell Armada
370/XP SOCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pch_gbe driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When umac_enable_set() is used to disable the UniMAC receiver or
transmitter, we need to make sure that we wait for a full-sized packet
to be processed because the UniMAC hardware stops on a packet boundary,
not immediately.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_unmap_single() was called with dma_unmap_len(cb, dma_len),
unfortunately we failed to assign this length field in
bcm_sysport_rx_refill() or bcm_sysport_alloc_rx_bufs() using
dma_unmap_len_set().
This causes packet contents corruption because are we not invoking the
cache invalidation routines with the proper length. Fix this by using
the full RX buffer size (RX_BUF_LENGTH) because the mappings for the RX
bufers are created with that size.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdev_priv is an accessor function, and has no purpose if its result is
not used.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@ local idexpression x; @@
-x = netdev_priv(...);
... when != x
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets need to be at least 64 bytes to enter the switch port logic,
including the FCS, otherwise they will be discarded as RUNT packets.
With packets having Broadcom tags, the 4-bytes tag is first stripped
off the packet, and the packet length is then checked, so we need to
make sure that the packet length with FCS is at least 64 bytes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link adjustment callback can be called as frequently as desired by
the PHY library, as such, let's avoid doing a Read/Modify/Write sequence
if nothing changed, which is more than likely since we are interfaced
with a switch device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These should not have trailing semicolons so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the behaviour with other network device drivers and
allows for a matching of the PCI device path in UDEV rules.
Signed-off-by: Markus Lottmann <markus.lottmann1986@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert kzalloc() to devm_kzalloc().
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the lone pr_err() to dev_err() call.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all pr_*() calls to dev_*() calls.
No functional changes.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse was reporting quite a few warnings for the driver.
Those get fixed by this patch.
Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the "info: why not propagate 'ret' from parse_trans_rule()..."
suggestion made by the smatch semantic checker on:
drivers/net/ethernet/mellanox/mlx4/mcg.c:867 mlx4_flow_attach()
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a positive value for error: MLX4_NET_TRANS_RULE_NUM instead
of -EPROTONOSUPPORT, to remove compilation warning.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Patches solves an issue that could raise when modifying the
device's MAC. It occurs due to a simultaneous access to priv->mac_hash
from two contexts. The buggy scenario described below:
Context 1: copy the new mac address to the dev->dev_addr field.
Context 2: mlx4_en_do_uc_filter removes prev_mac entry from the mac_hash
db since it is not in dev->uc and not equal to dev->dev_addr.
Context 1: mlx4_en_do_set_mac() calls mlx4_en_replace_mac() to replace
prev_mac with dev_addr but it fails to update the mac_hash db
since it no longer contains prev_mac, therefore it returns
with an error.
The fix is to prevent mlx4_en_do_uc_filter from being executed by both
of the context 1 calls described above, This is done by putting them
both under the mdev->state_lock lock, it will solve this issue since
mlx4_en_do_uc_filter is already protected by the mdev->state_lock.
Reviewed-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the "warn: suspicious bitop condition" made by the smatch semantic
checker on:
drivers/net/ethernet/mellanox/mlx4/main.c:509 mlx4_slave_cap()
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the "error: we previously assumed 'out_param' could be null" found
by smatch semantic checker on:
drivers/net/ethernet/mellanox/mlx4/cmd.c:506 mlx4_cmd_poll()
drivers/net/ethernet/mellanox/mlx4/cmd.c:578 mlx4_cmd_wait()
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix an issue that happen when changing the MAC address when
the port is down, described as follows:
1. Set the port down.
2. Change the MAC address - mlx4_en_set_mac() will change dev->dev_addr.
3. Set the port up - will result in mlx4_en_do_uc_filter that will
remove the prev_mac entry from the mac_hash db.
4. Changing the MAC address again will eventually trigger the call to
mlx4_en_replace_mac() in order to replace prev_mac with dev_addr but
the prev_mac entry is already not exist in the mac_hash db therefore
the operation fails.
The fix is to set the prev_mac with the new MAC address so in step 3
above, after setting the port up mlx4_en_get_qp() is updating the
mac_hash with the entry of dev_addr which is equal to prev_mac.
Therefore in step 4, when calling mlx4_en_replace_mac, the entry related
to prev_mac exist in mac_hash and the replace operation succeed.
Reviewed-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using ethtool set_channels, mlx4_en_setup_tc is always called, even
when it was not configured. Fixed code to call mlx4_en_setup_tc() only
if needed.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During heavy traffic, napi is constatntly polling the complition queue
and no interrupt is fired. Because of that, changes to irq affinity are
ignored until traffic is stopped and resumed.
By registering to the irq notifier mechanism, and forcing interrupt when
affinity is changed, irq affinity changes will be immediatly enforced.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I was converting the driver to the managed device API, only devm_kzalloc()
was available for memory allocation, so I had to use it, despite zeroing out the
PHY IRQ array right before initializing all its entries to PHY_POLL was quite
stupid. Now that devm_kmalloc_array() has become available, we can avoid the
needless zeroing out...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any TSO fragment hits hardware bug conditions (e.g. 4G boundary), the
driver will workaround by calling skb_copy() to copy to a linear SKB. Users
have reported page allocation failures as the TSO packet can be up to 64K.
Copying such a large packet is also very inefficient. We fix this by using
existing tg3_tso_bug() to transmit the packet using GSO.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 uses GSO as workaround if the hardware cannot perform TSO on certain
packets. We should not modify the ip header fields if we do GSO on the
packet. It happens to work by accident because GSO recalculates the IP
checksum and IP total length.
Also fix the tg3_start_xmit comment to reflect that this is the only
xmit function for all devices.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the set_rx_mode function to enable/disable
promiscuous or all-multicast modes and to update the multicast
filtering list of the device.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build when BNX2X_SRIOV is not enabled.
Change one parameter struct from bnx2 to bnx2x and don't return a value
from a void function.
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: 'struct bnx2' declared inside parameter list [enabled by default]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:60: warning: 'return' with a value, in function returning void [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM43xx phy mode selection is similar to AM33xx platform, so adding only
the compatibility string to the driver
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dra7xx support for selecting the phy mode which is present in control
module of dra7xx SoC
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv->dev is uninitialized, initializing with pdev->dev
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the cas_lock_tx function we acquire multiple locks in a loop and
need to use nested lock annotation to prevent lockdep warnings.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91ebb928b "bnx2x: Add support for Multi-Function UNDI" contains a bug
which prevent the emptying of the device's Rx buffers before reset.
As a result, on new boards it is likely HW will reach some fatal assertion
once its interfaces load after UNDI was previously loaded.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).
Cc: stable <stable@vger.kernel.org> # v3.8
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f8d56d8f89 ("net:
eth: cpsw: Correctly attach to GPIO bitbang MDIO driver").
Fix potential null-pointer dereference at probe if the mdio-gpio device
has not been successfully probed yet.
The offending commit is plain wrong for a number of reasons. First of
all it accesses internal driver data of an unrelated device. Neither
does it check that the data is non-null (which it is in case the device
has not been probed yet).
Furthermore, the decision on whether to treat any driver data according
to the mdio-gpio driver's internals is made based on the node name. But
the name is not compared against "mdio" which is the normal name for the
node, but rather against "gpio" which the node does not have to be named
(and shouldn't be according to the binding documentation). [ If this
hack is to be kept out-of-tree it should at least be matching against
the compatible property. ]
Cc: Stefan Roese <sr@denx.de>
Cc: stable <stable@vger.kernel.org> # v3.14
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_cmd_rss_config() is called after the MCCQ is created; so this cmd is
now modified to use the MCCQ instead of MBOX. Also fixed some indentation
problem in this routine.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For putting interface into vlan promiscuous mode, we use be_cmd_rx_filter()
and not be_cmd_vlan_config(). So remove the "promiscuous" argument from
be_cmd_vlan_config().
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manuel Schölling