We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Pramod Kumar <pramodku@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190812132554.18313-1-linus.walleij@linaro.org
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After we switched the two drivers that have .need_valid_mask
set to use the callback for setting up the .valid_mask,
we can just use the presence of the .init_valid_mask()
callback (or the OF reserved ranges, nota bene) to determine
whether to allocate the mask or not and we can drop the
.need_valid_mask field altogether.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819093058.10863-1-linus.walleij@linaro.org
This makes use of the existing callback to populate the
valid mask instead of iteratively setting it up during
probe.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819091140.622-1-linus.walleij@linaro.org
It is more helpful for drivers to have the affected fields
directly available when we use the callback to set up the
valid mask. Change this and switch over the only user
(MSM) to use the passed parameters. If we do this we can
also move the mask out of publicly visible struct fields.
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819084904.30027-1-linus.walleij@linaro.or
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Asus X571GT, GPIO 297 is configured as an interrupt and serves
for the touchpad. The touchpad will report input events much less
than expected after S3 suspend/resume, which results in extremely
slow cursor movement. However, the number of interrupts observed
from /proc/interrupts increases much more than expected even no
touching touchpad.
This is due to the value of PADCFG0 of PIN 225 for the interrupt
has been changed from 0x80800102 to 0x80100102. The GPIROUTIOXAPIC
is toggled on which results in the spurious interrupts. The PADCFG0
of PIN 225 is expected to be saved during suspend, but the 297 is
saved instead because the gpiochip_line_is_irq() expect the GPIO
offset but what's really passed to it is PIN number. In this case,
the /sys/kernel/debug/pinctrl/INT3450:00/gpio-ranges shows
288: INT3450:00 GPIOS [436 - 459] PINS [216 - 239]
So gpiochip_line_is_irq() returns true for GPIO offset 297, the
suspend routine spuriously saves the content for PIN 297 which
we expect to save for PIN 225.
This commit maps the PIN number to GPIO offset first in the
intel_pinctrl_should_save() to make sure the values for the
specific PINs can be correctly saved and then restored.
Fixes: c538b94367 ("pinctrl: intel: Only restore pins that are used by the driver")
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some firmwares would like to protect pads from being modified by OS
and at the same time provide them to OS as a resource. So, the driver
in such circumstances may request pad and may not change its state.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that the GPIO core has support for hierarchical IRQ chips, convert
Qualcomm's spmi-gpio over to use these new helpers to reduce duplicated
code across drivers.
This change was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190808123242.5359-3-linus.walleij@linaro.org
The old commit c58d9c1b26 ("sh-pfc: Implement generic pinconf
support") broke the cfg->type flag to PINMUX_TYPE_FUNCTION because
sh_pfc_pinconf_set() didn't call sh_pfc_reconfig_pin().
Now if we fix the cfg->type condition, it gets worse because:
- Some drivers might be deferred so that .set_mux() will be called
multiple times.
- In such the case, the sh-pfc driver returns -EBUSY even if
the group is the same, and then that driver fails to probe.
Since the pinctrl subsystem already has such conditions according
to @set_mux and @gpio_request_enable, this patch just remove
the incomplete flag from sh-pfc/pinctrl.c.
Fixes: c58d9c1b26 ("sh-pfc: Implement generic pinconf support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To clean/modify the code up later, this patch just adds new flags
"mux_set" and "gpio_enabled" into the struct sh_pfc_pin_config.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Each iteration of for_each_child_of_node() puts the previous node;
however, in the case of a return from the middle of the loop, there is no
put, thus causing a memory leak. Hence put of_node_put() statements as
required before two mid-loop return statements.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190808074720.15754-1-nishkadg.linux@gmail.com
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190808074329.15579-1-nishkadg.linux@gmail.com
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_child_of_node and
for_each_available_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190808075457.16109-1-nishkadg.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Version 1.08 of pin list has some changes in pin names for Intel Denverton.
Update the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
At the time of commit 9a643c9a11 ("sh-pfc: Convert message
printing from pr_* to dev_*"), the dev_*_once() variants didn't exist
yet, so the once behavior was open-coded.
Since commit e135303bd5 ("device: Add dev_<level>_once variants")
they do, so "revert" to the good practice of using a helper.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Replace hard coded constants with self-explanatory names, i.e.
use NSEC_PER_USEC for debounce calculus.
While here, add a unit suffix to debounce period constant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is more generic and simpler validation just against the nregs.
Using it allows to drop customization from the intel_get_padcfg().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20190804154948.4584-1-nishkadg.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
three places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804160420.5309-1-nishkadg.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804155154.4916-1-nishkadg.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804155117.4753-1-nishkadg.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_compatible_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in two
places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804152745.2231-1-nishkadg.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Improve readability and maintainability by replacing a hardcoded string
allocation and formatting by the use of the devm_kasprintf() helper.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190731132917.17607-4-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Improve readability and maintainability by replacing a hardcoded string
allocation and formatting by the use of the kasprintf() helper.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190731132917.17607-3-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Improve readability by replacing a hardcoded number requiring a comment
by strlen().
Gcc is smart enough to evaluate the length of a constant string at
compile-time.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190731132917.17607-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-34-swboyd@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for pinmux settings of aout1b group. This group includes
audio I/O signals derived from xirq pins, and it is equivalent to "aout1"
in functionality.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1564465410-9165-3-git-send-email-hayashi.kunihiko@socionext.com
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It depends on the board implementation whether to have each pins of
CTS/RTS, and others for modem. So it is necessary to divide current
uart_ctsrts group into uart_ctsrts and uart_modem groups.
Since the number of implemented pins for modem differs depending
on SoC, each uart_modem group also has a different number of pins.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1564465410-9165-2-git-send-email-hayashi.kunihiko@socionext.com
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing pinmux for the pwm_a function on the GPIOE_2 pin.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190729125838.6498-1-narmstrong@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise they look odd in the face of not being listed in the bindings
documents.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190724081313.12934-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2600 pinmux is fairly similar to the previous generations of
ASPEED BMC SoCs in terms of architecture, though differ in some of the
design details. The complexity of the pin expressions is largely reduced
(e.g. there are no-longer signals with multiple expressions muxing them
to the associated pin), and there are now signals and buses with
multiple pin groups.
The driver implements pinmux support for all 244 GPIO-capable pins plus
a further four pins that are not GPIO capable but which expose multiple
signals. pinconf will be implemented in a follow-up patch.
The implementation has been smoke-tested under qemu, and run on hardware
by ASPEED.
Debugged-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190711041942.23202-7-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2400 and AST2500 SoCs only exposed one pin group per function.
Lone pin groups drove some implementation simplifications in the ASPEED
pinmux infrastructure that is now invalid for the AST2600, which
supports multiple groups per function for some functions on the chip
(SMBus Alert pins and UARTs among others).
This patch reworks the macro jungle to enable support for multiple pin
groups. In the process we inflict some collateral damage on the existing
AST2400 and AST2500 drivers, but the rework is mostly a relatively
straight-forward, automated transform of adding the pin name as an
argument to some macro calls and implementing wrappers to paper over
groups in the cases where there aren't multiple.
As previously documented, the macro infrastructure exposes mux
configuration as symbols in the source file which are used to detect
accidental duplication. Previously these symbols were named in terms of
the signal for a given expression. As the AST2600 supports multiple pin
groups for a function, the signal name on its own is no-longer unique,
and we must switch to the (signal, group) tuple. However, this means
that we can no-longer derive the signal expression symbol name from the
signal name alone, which among other cases, impacts the operation of the
PIN_DECL_x() macros.
To fix that and avoid requiring we awkwardly provide the associated
group name for every signal for every PIN_DECL_x() invocation, instead
opportunistically alias the name of the signal expression symbol from
the unique (signal, group) tuple to the also unique (pin, signal) tuple,
then reference the alias symbol in the tables generated by PIN_DECL_x().
This way we do not require extra group parameters for PIN_DECL_x() as
the pin name was already provided as an argument, and instead simply
require that the pin name be provided to the expression declaration
macros in order to generate the alias symbol.
The patch implements the alias strategy and fixes up all the expression
definition macro calls in the AST2400 and AST2500 drivers to account for
pin groups. Given the implementation strategy has the property that
compilation either fails or loudly warns for bad pin descriptions, this
patch is theoretically tested by successfully compiling both affected
drivers. For a more practical test I've inspected the diff of the
content of the pinctrl debugfs entries before and after the patch under
qemu; all pins, functions and groups match.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190729055604.13239-5-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename macros as follows:
* s/SS_PIN_DECL()/PIN_DECL_1()/
* s/MS_PIN_DECL()/PIN_DECL_2()/
* s/MS_PIN_DECL_()/PIN_DECL_()/
This is in preparation for adding PIN_DECL_3(). We could clean this up
with e.g. CPPMAGIC_MAP() from ccan, but that might be a bridge too far
given how much of a macro jungle we already have.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190729055604.13239-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce the GPIO pins that is only available on V3 (not on V3s) to the
V3s pinctrl driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190728031227.49140-2-icenowy@aosc.io
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When fall-through warnings was enabled by default the following warnings
was starting to show up:
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c: In function ‘pmic_gpio_populate’:
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:815:20: warning: this statement may fall
through [-Wimplicit-fallthrough=]
pad->have_buffer = true;
~~~~~~~~~~~~~~~~~^~~~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:816:2: note: here
case PMIC_GPIO_SUBTYPE_GPIOC_4CH:
^~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:820:20: warning: this statement may fall
through [-Wimplicit-fallthrough=]
pad->have_buffer = true;
~~~~~~~~~~~~~~~~~^~~~~~
../drivers/pinctrl/qcom/pinctrl-spmi-gpio.c:821:2: note: here
case PMIC_GPIO_SUBTYPE_GPIOC_8CH:
^~~~
Rework so that the compiler doesn't warn about fall-through.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20190726112816.19723-1-anders.roxell@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When fall-through warnings was enabled by default the following warning
was starting to show up:
../drivers/pinctrl/pinctrl-rockchip.c: In function ‘rockchip_gpio_set_config’:
../drivers/pinctrl/pinctrl-rockchip.c:2783:3: warning: this statement may fall
through [-Wimplicit-fallthrough=]
rockchip_gpio_set_debounce(gc, offset, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/pinctrl/pinctrl-rockchip.c:2795:2: note: here
default:
^~~~~~~
Rework so that the compiler doesn't warn about fall-through. Add
'return -ENOTSUPP;' to match the comment.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20190726112812.19665-1-anders.roxell@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/pinctrl/pinctrl-oxnas.c: In function oxnas_ox810se_pinconf_set:
drivers/pinctrl/pinctrl-oxnas.c:905:6: warning: variable arg set but not used [-Wunused-but-set-variable]
drivers/pinctrl/pinctrl-oxnas.c: In function oxnas_ox820_pinconf_set:
drivers/pinctrl/pinctrl-oxnas.c:944:6: warning: variable arg set but not used [-Wunused-but-set-variable]
It is never used since commit 4b0c0c25fa ("pinctrl:
oxnas: Add support for OX820"), so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190725142419.29892-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the following tab (coming from STMFX datasheet), updates
have to done in stmfx_pinconf_set function:
-"type" has to be set when "bias" is configured as "pull-up or pull-down"
-PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
output. There is so no need to check direction.
DIR | TYPE | PUPD | MFX GPIO configuration
----|------|------|---------------------------------------------------
1 | 1 | 1 | OUTPUT open drain with internal pull-up resistor
----|------|------|---------------------------------------------------
1 | 1 | 0 | OUTPUT open drain with internal pull-down resistor
----|------|------|---------------------------------------------------
1 | 0 | 0/1 | OUTPUT push pull no pull
----|------|------|---------------------------------------------------
0 | 1 | 1 | INPUT with internal pull-up resistor
----|------|------|---------------------------------------------------
0 | 1 | 0 | INPUT with internal pull-down resistor
----|------|------|---------------------------------------------------
0 | 0 | 1 | INPUT floating
----|------|------|---------------------------------------------------
0 | 0 | 0 | analog (GPIO not used, default setting)
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/1564053416-32192-1-git-send-email-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the follow-up pin design on Spreadtrum platform has some changes,
some configuration of MISC_PIN moved to COMMON_PIN. To support current
pin design and keep backward compatibility, we should combine the
condition of MISC_PIN and COMMON_PIN to configure an individual pin.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/17af5e761e0515d288a7ea4078ac9aa4a82a7a4e.1564048446.git.baolin.wang@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the pinctrl configuration for the CS47L15 codec to
the madera pinctrl driver.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190722091015.20884-2-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BCM2711 has a new way of selecting the pull-up/pull-down setting
for a GPIO pin. The registers used for the BCM2835, GP_PUD and
GP_PUDCLKn0, are no longer connected. A new set of registers,
GP_GPIO_PUP_PDN_CNTRL_REGx must be used. This commit will add
a new compatible string "brcm,bcm2711-gpio" and the kernel
driver will use it to select which method is used to select
pull-up/pull-down.
This patch based on a patch by Al Cooper which was intended for the
BCM7211. This is a bugfixed and improved version.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/1563776607-8368-3-git-send-email-wahrenst@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for Tegra pinctrl driver suspend and resume.
During suspend, context of all pinctrl registers are stored and
on resume they are all restored to have all the pinmux and pad
configuration for normal operation.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1564607463-28802-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
three places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190719032414.85369-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix sparse warning:
drivers/pinctrl/aspeed/pinmux-aspeed.c:8:12: warning:
symbol 'aspeed_pinmux_ips' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190711142457.37028-1-yuehaibing@huawei.com
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TSIF is the Transport Stream Interface.
First, rename tsif1 to tsif0, and tsif2 to tsif1.
Then squash all 5 tsif0 pins into a single function.
Same for tsif1.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Link: https://lore.kernel.org/r/503b2ae8-ead6-70cd-7b21-ce5f5166a23a@free.fr
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While sorting out some devicetree issues I found that the pinctrl driver
was failing to acquire its GFX regmap even though the phandle was
present in the devicetree:
[ 0.124190] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: No GFX phandle found, some mux configurations may fail
Without access to the GFX regmap we fail to configure the mux for the
VPO function:
[ 1.548866] pinctrl core: add 1 pinctrl maps
[ 1.549826] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: found group selector 164 for VPO
[ 1.550638] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 144 (V20) for 1e6e6000.display
[ 1.551346] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 145 (U19) for 1e6e6000.display
...
[ 1.562057] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 218 (T22) for 1e6e6000.display
[ 1.562541] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 219 (R20) for 1e6e6000.display
[ 1.563113] Muxing pin 144 for VPO
[ 1.563456] Want SCU8C[0x00000001]=0x1, got 0x0 from 0x00000000
[ 1.564624] aspeed_gfx 1e6e6000.display: Error applying setting, reverse things back
This turned out to be a simple problem of timing: The ASPEED pinctrl
driver is probed during arch_initcall(), while GFX is processed much
later. As such the GFX syscon is not yet registered during the pinctrl
probe() and we get an -EPROBE_DEFER when we try to look it up, however
we must not defer probing the pinctrl driver for the inability to mux
some GFX-related functions.
Switch to lazily grabbing the regmaps when they're first required by the
mux configuration. This generates a bit of noise in the patch as we have
to drop the `const` qualifier on arguments for several function
prototypes, but has the benefit of working.
I've smoke tested this for the ast2500-evb under qemu with a dummy
graphics device. We now succeed in our attempts to configure the SoC's
VPO pinmux function.
Fixes: 7d29ed88ac ("pinctrl: aspeed: Read and write bits in LPC and GFX controllers")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190724080155.12209-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Lina Iyer <ilina@codeaurora.org>
Link: https://lore.kernel.org/r/20190724083828.7496-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to duplicate the check which is done in the common
intel_pinctrl_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Further cleanup from the SPDX fixup fallout for the recent ASPEED
series. aspeed_g4_defconfig, aspeed_g5_defconfig and multi_v5_defconfig
now compile. Smoke tested the g4 and g5 kernels under QEMU's
palmetto-bmc and romulus-bmc machines respectively.
Fixes: 35d8510ea3ad ("pinctrl: aspeed: Fix missed include")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190710032216.4088-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SPDX churn made my fixes drop an important include
from the Aspeed pinctrl header. Fix it up.
Cc: Andrew Jeffery <andrew@aj.id.au>
Reported-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190703151554.30454-1-andriy.shevchenko@linux.intel.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190703003018.75186-2-andriy.shevchenko@linux.intel.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the fact byt_get_gpio_mux() returns a value of mux settings as
it is represented in hardware. Use defined macro instead of magic numbers
to clarify this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190703003018.75186-1-andriy.shevchenko@linux.intel.com
Reviewed-By: Enrico Weigelt <info@metux.net>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration with
pinctrl framework for SM8150
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org>
[vkoul: modify to use upstream tile support
use upstream code style
order the functions and squash functions]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190702105045.27646-4-vkoul@kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some subsystems, such as pinctrl, allow continuing to defer probe
indefinitely. This is useful for devices that depend on resources
provided by devices that are only probed after the init stage.
One example of this can be seen on Tegra, where the DPAUX hardware
contains pinmuxing controls for pins that it shares with an I2C
controller. The I2C controller is typically used for communication
with a monitor over HDMI (DDC). However, other instances of the I2C
controller are used to access system critical components, such as a
PMIC. The I2C controller driver will therefore usually be a builtin
driver, whereas the DPAUX driver is part of the display driver that
is loaded from a module to avoid bloating the kernel image with all
of the DRM/KMS subsystem.
In this particular case the pins used by this I2C/DDC controller
become accessible very late in the boot process. However, since the
controller is only used in conjunction with display, that's not an
issue.
Unfortunately the driver core currently outputs a warning message
when a device fails to get the pinctrl before the end of the init
stage. That can be confusing for the user because it may sound like
an unwanted error occurred, whereas it's really an expected and
harmless situation.
In order to eliminate this warning, this patch allows callers of the
driver_deferred_probe_check_state() helper to specify that they want
to continue deferring probe, regardless of whether we're past the
init stage or not. All of the callers of that function are updated
for the new signature, but only the pinctrl subsystem passes a true
value in the new persist parameter if appropriate.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190621151725.20414-1-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ASPEED pinctrl driver implementations make heavy use of macros to
minimise tedium of implementation and maximise the chance that the
compiler will catch errors in defining signal and pin configurations.
While the goal of minimising errors is achieved, it is at the cost of
the complexity of the macros.
Document examples of the expanded form of pin declarations to
demonstrate the operation of the macros.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-9-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ASPEED have completely rearranged the System Control Unit register
layout with the AST2600. The existing code took advantage of the fact
that the AST2400 and AST2500 had layouts that were similar enough to
have little impact on the pinmux infrastructure (though there is a wart
with read-modify-write vs write-1-clear semantics of the hardware
strapping registers between the two).
Given that any similarity has been thrown out with the AST2600, separate
out the function applying an expression state to be driver-specific.
With it, extract out the pinmux macro jungle to its own header and
implementation so the pieces can be composed without dependency cycles.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-8-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Writes of 1 to SCU7C clear set bits in SCU70, the hardware strapping
register. The information was correct if you squinted while reading, but
hopefully switching the order of the registers as listed conveys it
better.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-7-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have handled the GFX register case for quite some time now.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-6-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce the irq_enable callback which will be same as irq_unmask
except that it will also clear the status bit before unmask.
This will help in clearing any erroneous interrupts that would
have got latched when the interrupt is not in use.
There may be devices like UART which can use the same gpio line
for data rx as well as a wakeup gpio when in suspend. The data that
was flowing on the line may latch the interrupt and when we enable
the interrupt before going to suspend, this would trigger the
unexpected interrupt. This change helps clearing the interrupt
so that these unexpected interrupts gets cleared.
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Link: https://lore.kernel.org/r/1561472086-23360-1-git-send-email-neeraju@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fix IRQ setup in the MCP23s08.
- Fix pin setup on pins > 31 in the Ocelot driver.
- Fix IRQs in the Mediatek driver.
-----BEGIN PGP SIGNATURE-----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=/GFO
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Sorry to bomb in fixes this late. Maybe I can comfort you by saying it
is only driver fixes, and mostly IRQ handling which is something GPIO
and pin control drivers never get right. You think it works and then
it doesn't.
Summary:
- Fix IRQ setup in the MCP23s08.
- Fix pin setup on pins > 31 in the Ocelot driver.
- Fix IRQs in the Mediatek driver"
* tag 'pinctrl-v5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: Update cur_mask in mask/mask ops
pinctrl: mediatek: Ignore interrupts that are wake only during resume
pinctrl: ocelot: fix pinmuxing for pins after 31
pinctrl: ocelot: fix gpio direction for pins after 31
pinctrl: mcp23s08: Fix add_data and irqchip_add_nested call order
During suspend/resume, mtk_eint_mask may be called while
wake_mask is active. For example, this happens if a wake-source
with an active interrupt handler wakes the system:
irq/pm.c:irq_pm_check_wakeup would disable the interrupt, so
that it can be handled later on in the resume flow.
However, this may happen before mtk_eint_do_resume is called:
in this case, wake_mask is loaded, and cur_mask is restored
from an older copy, re-enabling the interrupt, and causing
an interrupt storm (especially for level interrupts).
Step by step, for a line that has both wake and interrupt enabled:
1. cur_mask[irq] = 1; wake_mask[irq] = 1; EINT_EN[irq] = 1 (interrupt
enabled at hardware level)
2. System suspends, resumes due to that line (at this stage EINT_EN
== wake_mask)
3. irq_pm_check_wakeup is called, and disables the interrupt =>
EINT_EN[irq] = 0, but we still have cur_mask[irq] = 1
4. mtk_eint_do_resume is called, and restores EINT_EN = cur_mask, so
it reenables EINT_EN[irq] = 1 => interrupt storm as the driver
is not yet ready to handle the interrupt.
This patch fixes the issue in step 3, by recording all mask/unmask
changes in cur_mask. This also avoids the need to read the current
mask in eint_do_suspend, and we can remove mtk_eint_chip_read_mask
function.
The interrupt will be re-enabled properly later on, sometimes after
mtk_eint_do_resume, when the driver is ready to handle it.
Fixes: 58a5e1b64b ("pinctrl: mediatek: Implement wake handler and suspend resume")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before suspending, mtk-eint would set the interrupt mask to the
one in wake_mask. However, some of these interrupts may not have a
corresponding interrupt handler, or the interrupt may be disabled.
On resume, the eint irq handler would trigger nevertheless,
and irq/pm.c:irq_pm_check_wakeup would be called, which would
try to call irq_disable. However, if the interrupt is not enabled
(irqd_irq_disabled(&desc->irq_data) is true), the call does nothing,
and the interrupt is left enabled in the eint driver.
Especially for level-sensitive interrupts, this will lead to an
interrupt storm on resume.
If we detect that an interrupt is only in wake_mask, but not in
cur_mask, we can just mask it out immediately (as mtk_eint_resume
would do anyway at a later stage in the resume sequence, when
restoring cur_mask).
Fixes: bf22ff45be ("genirq: Avoid unnecessary low level irq function calls")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPL-2.0-only is the preferred way of expressing v2 of the GPL, so switch
to that. Remove some redundant copyright notices and correct some
instances where the wrong comment type has been used in header files.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when CONFIG_ACPI is unset:
drivers/pinctrl/qcom/pinctrl-sdm845.c:1320:5: warning: 'CONFIG_ACPI' is
not defined, evaluates to 0 [-Wundef]
#if CONFIG_ACPI
^
1 warning generated.
Use ifdef instead of if to resolve this.
Fixes: a229105d7a ("pinctrl: qcom: sdm845: Provide ACPI support")
Link: https://github.com/ClangBuiltLinux/linux/issues/569
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The actual layout for OCELOT_GPIO_ALT[01] when there are more than 32 pins
is interleaved, i.e. OCELOT_GPIO_ALT0[0], OCELOT_GPIO_ALT1[0],
OCELOT_GPIO_ALT0[1], OCELOT_GPIO_ALT1[1]. Introduce a new REG_ALT macro to
facilitate the register offset calculation and use it where necessary.
Fixes: da801ab56a pinctrl: ocelot: add MSCC Jaguar2 support
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The third argument passed to REG is not the correct one and
ocelot_gpio_set_direction is not working for pins after 31. Fix that by
passing the pin number instead of the modulo 32 value.
Fixes: da801ab56a pinctrl: ocelot: add MSCC Jaguar2 support
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pin groups have park bits for multiple pins in one register.
Support this by turning the parked bit field into a parked bitmask
field. If no parked bits are supported, the bitmask can be 0.
Update the pingroup table on Tegra210, which is the only generation
where this is supported, with the parked bitmask.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rather than reuse the nvidia,tegra30-gpio compatible string
to find the GPIO controller on Tegra30, Tegra114, Tegra124 and
Tegra210, use the most specific compatible string for each
SoC generation for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 98DX1135 is a switch chip with an integrated CPU. This is similar to
the 98DX4122 except the MPP assignments differ.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently probing of the mcp23s08 results in an error message
"detected irqchip that is shared with multiple gpiochips:
please fix the driver"
This is due to the following:
Call to mcp23s08_irqchip_setup() with call hierarchy:
mcp23s08_irqchip_setup()
gpiochip_irqchip_add_nested()
gpiochip_irqchip_add_key()
gpiochip_set_irq_hooks()
Call to devm_gpiochip_add_data() with call hierarchy:
devm_gpiochip_add_data()
gpiochip_add_data_with_key()
gpiochip_add_irqchip()
gpiochip_set_irq_hooks()
The gpiochip_add_irqchip() returns immediately if there isn't a irqchip
but we added a irqchip due to the previous mcp23s08_irqchip_setup()
call. So it calls gpiochip_set_irq_hooks() a second time.
Fix this by moving the call to devm_gpiochip_add_data before
the call to mcp23s08_irqchip_setup
Fixes: 02e389e63e ("pinctrl: mcp23s08: fix irq setup order")
Suggested-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OK so some automatic scripts were fixing the SPDX tags in
the mainline branch while we were patching other stuff,
and yeah it is more correct to have "GPL-2.0-only" rather
than "GPL-2.0" so let's conform to what is already upstream
so we don't end up getting the wrong license on the merged
result later.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides basic support for booting with ACPI instead
of the currently supported Device Tree. When doing so there are a
couple of differences which we need to taken into consideration.
Firstly, the SDM850 ACPI tables omit information pertaining to the
4 reserved GPIOs on the platform. If Linux attempts to touch/
initialise any of these lines, the firmware will restart the
platform.
Secondly, when booting with ACPI, it is expected that the firmware
will set-up things like; Regulators, Clocks, Pin Functions, etc in
their ideal configuration. Thus, the possible Pin Functions
available to this platform are not advertised when providing the
higher GPIOD/Pinctrl APIs with pin information.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When booting MSM based platforms with Device Tree or some ACPI
implementations, it is possible to provide a list of reserved pins
via the 'gpio-reserved-ranges' and 'gpios' properties respectively.
However some ACPI tables are not populated with this information,
thus it has to come from a knowledgable device driver instead.
Here we provide the MSM common driver with additional support to
parse this informtion and correctly populate the widely used
'valid_mask'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function was used by pin_request() to pointlessly double-check
the pin validity, and it was the only user ever.
Since commit d2f6a1c6fb ("pinctrl: remove double pin validity
check."), no one has ever used it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The iterator is initialized in list_for_each_entry().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add more checks for pinctrl table validation,
- Add TPU (Timer Pulse Unit / PWM) pin groups on R-Car H3, M3-W, and
M3-N,
- Rework description of pins without GPIO functionality,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXPoQPgAKCRCKwlD9ZEnx
cJ+eAP9iGeeArK/xRIort1N8dqdM60LB1p+CJGujASLLPgjAQQD/fiaeX+Wk15Oh
dd65Xr/LLN9itRdXBmNyumRf9Z3J5QM=
=t9qM
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.3-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.3
- Add more checks for pinctrl table validation,
- Add TPU (Timer Pulse Unit / PWM) pin groups on R-Car H3, M3-W, and
M3-N,
- Rework description of pins without GPIO functionality,
- Small fixes and cleanups.
Update the code to use a flexible array member instead of a pointer in
structure tb10x_pinctrl and use the struct_size() helper:
struct tb10x_pinctrl {
...
struct tb10x_of_pinfunc pinfuncs[];
};
Also, make use of the struct_size() helper instead of an open-coded
version in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(struct tb10x_pinctrl) + of_get_child_count(of_node) * sizeof(struct tb10x_of_pinfunc)
with:
struct_size(state, pinfuncs, of_get_child_count(of_node))
This code was detected with the help of Coccinelle.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SGPM pinmux to ast2500-pinctrl function and group, to prepare for
supporting SGPIO in AST2500 SoC.
Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ufs_reset pin is expected to be wired to the reset pin of the
primary UFS memory but is pretty much just a general purpose output pinr
Reorder the pins and expose it as gpio 150, so that the UFS driver can
toggle it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can distribute it and or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope it will be useful but without any warranty
without even the implied warranty of merchantability or fitness for
a particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 24 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.872212424@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
under gplv2 only
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.847550565@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
publishhed by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 48 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.292339952@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now all Renesas pin control drivers have been converted to use the new
non-GPIO helper macros, SH_PFC_PIN_NAMED() and SH_PFC_PIN_NAMED_CFG()
are no longer used. Remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the SH-Mobile AG5 pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the SH-Mobile AG5 SoC (in 34x34 BGA package) by
symbolic enum values, referring to signal names.
Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car E3 pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car E3 SoC (in 25x25 FCBGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car M3-N pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car M3-N SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car M3-W pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car M3-W SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car H3 ES2.0 and later pin control driver to use the new
macros for describing pins without GPIO functionality. This replaces
the use of physical pin numbers on the R-Car H3 ES2.0 SiP (in 39x39
BGA package) by symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car H3 ES1.x pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car H3 ES1.x SiP (in 39x39 BGA package) by
symbolic enum values, referring to signal names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car H2 pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car H2 SoC (in 31x31 FCBGA package) by
symbolic enum values, referring to signal names.
Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the R-Car M1A pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the R-Car M1A SoC (in 25x25 FCBGA package) by
symbolic enum values, referring to signal names.
Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Update the EMMA Mobile EV2 pin control driver to use the new macros for
describing pins without GPIO functionality. This replaces the use of
physical pin numbers on the EMMA Mobile EV2 SoC (in 23x23 BGA package)
by symbolic enum values, referring to signal names.
Note that the user-visible names of these pins are still based on pin
numbers instead of signal names, to preserve DT backwards compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Add new macros for describing pins without GPIO functionality:
- NOGP_ALL() expands to a list of PIN_id values, to be used for
generating symbolic enum values,
- PINMUX_NOGP_ALL() expands to a list of sh_pfc_pin entries, to
list all pins and their capabilities.
Both macros depend on an SoC-specific CPU_ALL_NOGP() macro, to be
provided by each individual SoC pin control driver.
The new macros offer two advantages over the existing SH_PFC_PIN_NAMED()
and SH_PFC_PIN_NAMED_CFG() macros:
1. They do not rely on PIN_NUMBER() macros and physical pin numbering,
hence do not suffer from pin numbering confusion among different
SoC/SiP packages.
2. They are similar in spirit to the existing scheme for handling pins
with GPIO functionality.
Note that internal to the driver, non-GPIO pins use a sequential
numbering scheme which starts after the highest GPIO pin number in use.
This value is calculated automatically, using two new helper macros, for
systems with either 32-port bank (GP port style) or linear (PORT style)
pin space. Sample expansion:
GP_LAST = sizeof(union {
char dummy[0] __attribute__((deprecated, deprecated));
char GP_0_0[(0 * 32) + 0] __attribute__((deprecated, deprecated));
char GP_0_1[(0 * 32) + 1] __attribute__((deprecated, deprecated));
...
char GP_7_3[(7 * 32) + 3] __attribute__((deprecated, deprecated));
})
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
drivers/pinctrl/bcm/pinctrl-bcm2835.c: In function bcm2835_pctl_dt_node_to_map:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:720:8: error: implicit declaration of function pinconf_generic_dt_node_to_map_all;
drivers/pinctrl/bcm/pinctrl-bcm2835.c: In function bcm2835_pinctrl_probe:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:1022:15: error: struct gpio_chip has no member named of_node
pc->gpio_chip.of_node = np;
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0de704955e ("pinctrl: bcm2835: Add support for generic pinctrl binding")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using STM32 as guinea pig after Alex's initial positive
test to see if this is something we should encourage
in general and make default behaviour.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting this up will configure wake from suspend properly,
and wake only for the interrupts that are setup in wake_mask,
not all interrupts.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl variants that include pinctrl-paris.h (and not
pinctrl-mtk-common.h) also need to use pm_ops to setup
wake mask properly, so copy over the pm_ops from common
to paris variant.
It is not easy to merge the 2 copies (or move
mtk_eint_suspend/resume to mtk-eint.c), as we need to
dereference pctrl->eint, and struct mtk_pinctrl *pctl has a
different structure definition for v1 and v2 (which is
what paris variant uses).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra194 has PCIE L5 rst and clkreq pins which need to be controlled
dynamically at runtime. This driver supports change pinmux for these
pins. Pinmux for rest of the pins is set statically by bootloader and
will not be changed by this driver
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Suresh Mangipudi <smangipudi@nvidia.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra194 chip has 32 bit pinctrl registers. Existing register defines in
header are only 16 bit.
Modified common pinctrl-tegra driver to support 32 bit registers of
Tegra 194 and later chips.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Prior to the adoption of SPDX, it was difficult for tools to determine
the correct license due to incomplete or badly formatted license text.
The SPDX solves this issue, assuming people can correctly spell
"SPDX-License-Identifier" although this assumption is broken in some
places.
Since scripts/spdxcheck.py parses only lines that exactly matches to
the correct tag, it cannot (should not) detect this kind of error.
If the correct tag is missing, scripts/checkpatch.pl warns like this:
WARNING: Missing or malformed SPDX-License-Identifier tag in line *
So, people should notice it before the patch submission, but in reality
broken tags sometimes slip in. The checkpatch warning is not useful for
checking the committed files globally since large number of files still
have no SPDX tag.
Also, I am not sure about the legal effect when the SPDX tag is broken.
Anyway, these typos are absolutely worth fixing. It is pretty easy to
find suspicious lines by grep.
$ git grep --not -e SPDX-License-Identifier --and -e SPDX- -- \
:^LICENSES :^scripts/spdxcheck.py :^*/license-rules.rst
arch/arm/kernel/bugs.c:// SPDX-Identifier: GPL-2.0
drivers/phy/st/phy-stm32-usbphyc.c:// SPDX-Licence-Identifier: GPL-2.0
drivers/pinctrl/sh-pfc/pfc-r8a77980.c:// SPDX-Lincense-Identifier: GPL 2.0
lib/test_stackinit.c:// SPDX-Licenses: GPLv2
sound/soc/codecs/max9759.c:// SPDX-Licence-Identifier: GPL-2.0
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Interrupt clearing fix for the Intel pin controllers affecting
touchpads on some laptops.
- Compile Kconfig fix for the STMFX expander pin controller.
-----BEGIN PGP SIGNATURE-----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=XtxG
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"The commits that stand out are the Intel fixes that arrived during the
merge window and I got relayed by pull request from Andy.
Apart from that a minor Kconfig noise.
- Interrupt clearing fix for the Intel pin controllers affecting
touchpads on some laptops.
- Compile Kconfig fix for the STMFX expander pin controller"
* tag 'pinctrl-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: stmfx: Fix compile issue when CONFIG_OF_GPIO is not defined
pinctrl: intel: Clear interrupt status in mask/unmask callback
pinctrl: intel: Use GENMASK() consistently
Fix a laggish ELAN touchpad responsiveness due to an odd interrupt masking.
The following is an automated git shortlog grouped by driver:
intel:
- Clear interrupt status in mask/unmask callback
- Use GENMASK() consistently
-----BEGIN PGP SIGNATURE-----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=8RfE
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.2-2
Fix a laggish ELAN touchpad responsiveness due to an odd interrupt masking.
The following is an automated git shortlog grouped by driver:
intel:
- Clear interrupt status in mask/unmask callback
- Use GENMASK() consistently
Add pinconf support for Bitmain BM1880 SoC. Pinconf support includes
pin bias, slew rate and schmitt trigger. Drive strength support will
be added later.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rework the BM1880 SoC pinmux handling by removing the
BM1880_PINMUX_FUNCTION_MUX define and merging it with the
BM1880_PINMUX_FUNCTION definition. Since the PWM muxing is handled by
generic pin controller in the SoC itself, there is no need to have a
dedicated code to do the muxing in PWM registers. So, lets club all
pinmux handling in the same per pin mux handling code.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinconf support for PIN_CONFIG_OUTPUT_ENABLE and PIN_CONFIG_OUTPUT
in the meson pinctrl driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs are split between several banks (A, B, ...) and each bank can have
up to 16 lines. Those GPIOs could be used as interrupt lines thanks to
exti lines. As there are only 16 exti lines, a mux is used to select which
gpio line is connected to which exti line. Mapping is done as follow:
-A0, B0, C0.. -->exti_line_0 (X0 selected by mux_0)
-A1, B1, C1.. -->exti_line_1 (X1 selected by mux_1)
...
This patch adds a protection to avoid overriding on mux_n for exti_line_n.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During power sequence, GPIO hardware registers could be lost if the power
supply is switched off. Each device using pinctrl API is in charge of
managing pins during suspend/resume sequences. But for pins used as gpio or
irq stm32 pinctrl driver has to save the hardware configuration.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When CONFIG_GPIO_OF is not defined, struct gpio_chip 'of_node' member does
not exist:
drivers/pinctrl/pinctrl-stmfx.c: In function 'stmfx_pinctrl_probe':
drivers/pinctrl/pinctrl-stmfx.c:652:17: error: 'struct gpio_chip' has no member named 'of_node'
pctl->gpio_chip.of_node = np;
Fixes: 1490d9f841 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hogs would create circular device links, so do not link
the device to itself.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set create_link to inform pinctrl core that stmfx wants to create
link with its consumers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A pin controller may want to create a link between itself
and its clients to be sure of suspend/resume call ordering.
Introduce link_consumers field in pinctrl_desc structure to let
pinctrl core knows that controller expect to create a link.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
[Renamed create_link to link_consumers]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARCH_BRCMSTB needs to use the BCM2835 pin controller for chips
like BCM7211 which adopted that pin controller for GPIO. This
commit makes the option menu configurable with default enabled
for ARCH_BRCMSTB and ARCH_BCM2835.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
rework bias enable/disable part to prepare drive-strength integration
no functional changes
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add drive-strength-microamp property support to allow drive strength in uA
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-rockchip.c:3221:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-rockchip.c:3223:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of the custom PORT_GP_PUP_27() macro by using the common
PORT_GP_CFG_27() macro instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This follows the style of the existing PORT_GP_X macros, and will be
used by a follow-up patch for the r8a7778 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on the R-Car M3-N SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on the R-Car M3-W and RZ/G2M SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on revisions ES2.x and later of the R-Car H3 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on revision ES1.x of the R-Car H3 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Hardware Manual Errata for rev. 1.50 of March 26, 2019 removed the bit
definitions for MMC_CD and MMC_WP in the documentation for the IPSR6 and
IPSR7 registers, as these pin functionalities do not exist on R-Car
V3M.
Remove the definitions, and the corrresponding pins and groups.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Several drivers have identical definitions for PIN_NONE.
Provide a definition with a SH_PFC_ prefix for general use in sh_pfc.h,
and convert all drivers over to use it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
It is very common for a pin to support both pull-up and pull-down
functionality. Hence add a shorthand SH_PFC_PIN_CFG_PULL_UP_DOWN.
This not only reduces typing, but also avoids the need for several line
breaks, and makes many overly long lines shorter, improving
readability.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
There are two variants of the CPU_ALL_PORT() macro in use:
1. A three-parameter variant, to be provided for SoCs with a linear
GPIO pin space ("PORT style"),
2. A two-parameter variant, to be provided for SoCs with 32-port GPIO
banks ("GP port style").
Rename the 2-parameter variant to CPU_ALL_GP(), to avoid confusion, and
to increase naming consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Extend the run-time debug code with checks to ensure there are no
conflicting pin names, numbers, or enumeration values.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The pinmux groups and functions arrays may contain two parts, to ease
supporting SoCs that expose pin subsets of other related SoCs. Both
parts need to be declared with explicit sizes, which thus need to be
updated when adding support for more groups and functions.
If a size is too small, the compiler will detect this at build time
("excess elements in array initializer").
If a size is too large, this may go undetected (for pin groups), lead to
pin controller registration failures (for pin functions: "pinmux ops has
no name for functionN"), or crash the optional run-time debug code (for
pin groups).
Extend the run-time debug code with checks to detect this, to help
catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
All run-time debug code is called from sh_pfc_init(), which is __init.
Fixes: 6161b39a14 ("pinctrl: sh-pfc: Validate pinmux tables at runtime when debugging")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Improve wording while at it.
Fixes: 6161b39a14 ("pinctrl: sh-pfc: Validate pinmux tables at runtime when debugging")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a939bb57cd ("pinctrl: intel: implement gpio_irq_enable") was
added because clearing interrupt status bit is required to avoid
unexpected behavior.
Turns out the unmask callback also needs the fix, which can solve weird
IRQ triggering issues on I2C touchpad ELAN1200.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- Document (kerneldoc) core mfd_add_devices() API
- New Drivers
- Add support for Altera SOCFPGA System Manager
- Add support for Maxim MAX77650/77651 PMIC
- Add support for Maxim MAX77663 PMIC
- Add support for ST Multi-Function eXpander (STMFX)
- New Device Support
- Add support for LEDs to Intel Cherry Trail Whiskey Cove PMIC
- Add support for RTC to SAMSUNG Electronics S2MPA01 PMIC
- Add support for SAM9X60 to Atmel HLCDC (High-end LCD Controller)
- Add support for USB X-Powers AXP 8xx PMICs
- Add support for Integrated Sensor Hub (ISH) to ChromeOS EC
- Add support for USB PD Logger to ChromeOS EC
- Add support for AXP223 to X-Powers AXP series PMICs
- Add support for Power Supply to X-Powers AXP 803 PMICs
- Add support for Comet Lake to Intel Low Power Subsystem
- Add support for Fingerprint MCU to ChromeOS EC
- Add support for Touchpad MCU to ChromeOS EC
- Move TI LM3532 support to LED
- New Functionality
- Add/extend DT support; max77650, max77620
- Add support for power-off; max77620
- Add support for clocking; syscon
- Add support for host sleep event; cros_ec
- Fix-ups
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
- Bug Fixes
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio
-----BEGIN PGP SIGNATURE-----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=dTSD
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
drivers/pinctrl/pinctrl-stmfx.c:441 stmfx_pinctrl_irq_set_type() warn: bitwise AND condition is false here
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
smatch warnings:
drivers/pinctrl/pinctrl-stmfx.c:225 stmfx_pinconf_get() warn: unsigned 'dir' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:228 stmfx_pinconf_get() warn: unsigned 'type' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:231 stmfx_pinconf_get() warn: unsigned 'pupd' is never less than zero.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to
be handled consistently. Unsurprisingly, we enforce the lines to
be either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone
does, so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed.
Such nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs
and outputs at the same time and after improving the MMIO library
we handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM
work as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update.
-----BEGIN PGP SIGNATURE-----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=rhto
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
module_i2c_driver and pinconf_generic_dt_node_to_map_pin are undeclared
if CONFIG_I2C and CONFIG_OF are not enabled.
Fixes: 1490d9f841 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Linus Walleij