cpuidle stop state implementation has minor optimizations for P10
where hardware preserves more SPR registers compared to P9. The
current P9 driver works for P10, although does few extra
save-restores. P9 driver can provide the required power management
features like SMT thread folding and core level power savings on a P10
platform.
Until the P10 stop driver is available, revert the commit which allows
for only P9 systems to utilize cpuidle and blocks all idle stop states
for P10. CPU idle states are enabled and tested on the P10 platform
with this fix.
This reverts commit 8747bf36f3.
Fixes: 8747bf36f3 ("powerpc/powernv/idle: Replace CPU feature check with PVR check")
Signed-off-by: Pratik Rajesh Sampat <psampat@linux.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200826082918.89306-1-psampat@linux.ibm.com
Fix a typo introduced during recent code cleanup, which could lead to
silently not freeing resources or an oops message (on PCI hotplug or
CAPI reset).
Only impacts ioda2, the code path for ioda1 is correct.
Fixes: 01e12629af ("powerpc/powernv/pci: Add explicit tracking of the DMA setup state")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200819130741.16769-1-fbarrat@linux.ibm.com
Initialising the value before using it is generally regarded as a good
idea so do that.
Fixes: 4c51f3e1e8 ("powerpc/powernv/sriov: Make single PE mode a per-BAR setting")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200803075408.132601-1-oohall@gmail.com
Gcc report warning as follows:
arch/powerpc/platforms/powernv/pci-sriov.c:602:25: warning:
variable 'phb' set but not used [-Wunused-but-set-variable]
602 | struct pnv_phb *phb;
| ^~~
This variable is not used, so this commit removing it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200727171112.2781-1-weiyongjun1@huawei.com
Previously iov->vfs_expanded was used for two purposes.
1) To work out how much we need to multiple the per-VF BAR size to figure
out the total space required for the IOV BAR.
2) To indicate that IOV is not usable with this device (vfs_expanded == 0).
We don't really need the field for either since the multiple in 1) is
always the number PEs supported by the PHB. Similarly, we don't really need
it in 2) either since the IOV data field will be NULL if we can't use IOV
with the device.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-16-oohall@gmail.com
Using single PE BARs to map an SR-IOV BAR is really a choice about what
strategy to use when mapping a BAR. It doesn't make much sense for this to
be a global setting since a device might have one large BAR which needs to
be mapped with single PE windows and another smaller BAR that can be mapped
with a regular segmented window. Make the segmented vs single decision a
per-BAR setting and clean up the logic that decides which mode to use.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-15-oohall@gmail.com
Split up the logic so that we have one branch that handles setting up a
segmented window and another that handles setting up single PE windows for
each VF.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-14-oohall@gmail.com
I want to refactor the loop this code is currently inside of. Hoist it on
out.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-13-oohall@gmail.com
Remove the IODA2 PHB checks. We already assume IODA2 in several places so
there's not much point in wrapping most of the setup and teardown process
in an if block.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-12-oohall@gmail.com
Currently the iov->pe_num_map[] does one of two things depending on
whether single PE mode is being used or not. When it is, this contains an
array which maps a vf_index to the corresponding PE number. When single PE
mode is not being used this contains a scalar which is the base PE for the
set of enabled VFs (for for VFn is base + n).
The array was necessary because when calling pnv_ioda_alloc_pe() there is
no guarantee that the allocated PEs would be contigious. We can now
allocate contigious blocks of PEs so this is no longer an issue. This
allows us to drop the if (single_mode) {} .. else {} block scattered
through the SR-IOV code which is a nice clean up.
This also fixes a bug in pnv_pci_sriov_disable() which is the non-atomic
bitmap_clear() to manipulate the PE allocation map. Other users of the map
assume it will be accessed with atomic ops.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-11-oohall@gmail.com
Rework the PE allocation logic to allow allocating blocks of PEs rather
than individually. We'll use this to allocate contigious blocks of PEs for
the SR-IOVs.
This patch also adds code to pnv_ioda_alloc_pe() and pnv_ioda_reserve_pe() to
use the existing, but unused, phb->pe_alloc_mutex. Currently these functions
use atomic bit ops to release a currently allocated PE number. However,
the pnv_ioda_alloc_pe() wants to have exclusive access to the bit map while
scanning for hole large enough to accomodate the allocation size.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-10-oohall@gmail.com
The sequence required to use the single PE BAR mode is kinda janky and
requires a little explanation. The API was designed with P7-IOC style
windows where the setup process is something like:
1. Configure the window start / end address
2. Enable the window
3. Map the segments of each window to the PE
For Single PE BARs the process is:
1. Set the PE for segment zero on a disabled window
2. Set the range
3. Enable the window
Move the OPAL calls into their own helper functions where the quirks can be
contained.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-9-oohall@gmail.com
No need for the multi-dimensional arrays, just use a bitmap.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-8-oohall@gmail.com
This prevents SR-IOV being used by making the SR-IOV BAR resources
unallocatable. Rename it to reflect what it actually does.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-7-oohall@gmail.com
SR-IOV support on PowerNV is a byzantine maze of hooks. I have no idea
how anyone is supposed to know how it works except through a lot of
stuffering. Write up some docs about the overall story to help out
the next sucker^Wperson who needs to tinker with it.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-6-oohall@gmail.com
pci-ioda.c is getting a bit unwieldly due to the amount of stuff jammed in
there. The SR-IOV support can be extracted easily enough and is mostly
standalone, so move it into a separate file.
This patch also moves the PowerNV SR-IOV specific fields from pci_dn and
moves them into a platform specific structure. I'm not sure how they ended
up in there in the first place, but leaking platform specifics into common
code has proven to be a terrible idea so far so lets stop doing that.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-5-oohall@gmail.com
We pre-configure the m64 window for IODA1 as a 1-1 segment-PE mapping,
similar to PHB3. Currently the actual mapping of segments occurs in
pnv_ioda_pick_m64_pe(), but we can move it into pnv_ioda1_init_m64() and
drop the IODA1 specific code paths in the PE setup / teardown.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-4-oohall@gmail.com
There's an optimisation in the PE setup which skips performing DMA
setup for a PE if we only have bridges in a PE. The assumption being
that only "real" devices will DMA to system memory, which is probably
fair. However, if we start off with only bridge devices in a PE then
add a non-bridge device the new device won't be able to use DMA because
we never configured it.
Fix this (admittedly pretty weird) edge case by tracking whether we've done
the DMA setup for the PE or not. If a non-bridge device is added to the PE
(via rescan or hotplug, or whatever) we can set up DMA on demand.
This also means the only remaining user of the old "DMA Weight" code is
the IODA1 DMA setup code that it was originally added for, which is good.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-3-oohall@gmail.com
Currently we have these two functions:
pnv_pci_ioda2_release_dma_pe(), and
pnv_pci_ioda2_release_pe_dma()
The first is used when tearing down VF PEs and the other is used for normal
devices. There's very little difference between the two though. The latter
(non-VF) will skip a call to pnv_pci_ioda2_unset_window() unless
CONFIG_IOMMU_API=y is set. There's no real point in doing this so fold the
two together.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-2-oohall@gmail.com
Add a helper to go from a pci_bus structure to the pnv_phb that hosts
that bus. There's a lot of instances of the following pattern:
struct pci_controller *hose = pci_bus_to_host(pdev->bus);
struct pnv_phb *phb = hose->private_data;
Without any other uses of the pci_controller inside the function. This
is hard to read since it requires you to memorise the contents of the
private data fields and kind of error prone since it involves blindly
assigning a void pointer. Add a helper to make it more concise and
explicit.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200722065715.1432738-1-oohall@gmail.com
The EEH core has a concept of a "PE tree" to support PowerNV. The PE tree
follows the PCI bus structures because a reset asserted on an upstream
bridge will be propagated to the downstream bridges. On pseries there's a
1-1 correspondence between what the guest sees are a PHB and a PE so the
"tree" is really just a single node.
Current the EEH core is reponsible for setting up this PE tree which it
does by traversing the pci_dn tree. The structure of the pci_dn tree
matches the bus tree on PowerNV which leads to the PE tree being "correct"
this setup method doesn't make a whole lot of sense and it's actively
confusing for the pseries case where it doesn't really do anything.
We want to remove the dependence on pci_dn anyway so this patch move
choosing where to insert a new PE into the platform code rather than
being part of the generic EEH code. For PowerNV this simplifies the
tree building logic and removes the use of pci_dn. For pseries we
keep the existing logic. I'm not really convinced it does anything
due to the 1-1 PE-to-PHB correspondence so every device under that
PHB should be in the same PE, but I'd rather not remove it entirely
until we've had a chance to look at it more deeply.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-14-oohall@gmail.com
The naming of eeh_{add_to|remove_from}_parent_pe() doesn't really reflect
what they actually do. If the PE referred to be edev->pe_config_addr
already exists under that PHB then the edev is added to that PE. However,
if the PE doesn't exist the a new one is created for the edev.
The bulk of the implementation of eeh_add_to_parent_pe() covers that
second case. Similarly, most of eeh_remove_from_parent_pe() is
determining when it's safe to delete a PE.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-12-oohall@gmail.com
The edev->class_code field is never referenced anywhere except for the
platform specific probe functions. The same information is available in
the pci_dev for PowerNV and in the pci_dn on pseries so we can remove
the field.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-11-oohall@gmail.com
Mechanical conversion of the eeh_ops interfaces to use eeh_dev to reference
a specific device rather than pci_dn. No functional changes.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-9-oohall@gmail.com
Mechanical conversion of the eeh_ops interfaces to use eeh_dev to reference
a specific device rather than pci_dn. No functional changes.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-7-oohall@gmail.com
There's a bunch of strange things about this code. First up is that none of
the fields being written to are functional for a VF. The SR-IOV
specification lists then as "Reserved, but OS should preserve" so writing
new values to them doesn't do anything and is clearly wrong from a
correctness perspective.
However, since VFs are designed to be managed by the OS there is an
argument to be made that we should be saving and restoring some parts of
config space. We already sort of do that by saving the first 64 bytes of
config space in the eeh_dev (see eeh_dev->config_space[]). This is
inadequate since it doesn't even consider saving and restoring the PCI
capability structures. However, this is a problem with EEH in general and
that needs to be fixed for non-VF devices too.
There's no real reason to keep around this around so delete it.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-6-oohall@gmail.com
This is used in precisely one place which is in pseries specific platform
code. There's no need to have the callback in eeh_ops since the platform
chooses the EEH PE addresses anyway. The PowerNV implementation has always
been a stub too so remove it.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-5-oohall@gmail.com
POWER9 onwards the support for the registers HID1, HID4, HID5 has been
receded.
Although mfspr on the above registers worked in Power9, In Power10
simulator is unrecognized. Moving their assignment under the
check for machines lower than Power9
Signed-off-by: Pratik Rajesh Sampat <psampat@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200721153708.89057-4-psampat@linux.ibm.com
Replace the variable name from using "pnv_first_spr_loss_level" to
"deep_spr_loss_state".
pnv_first_spr_loss_level is supposed to be the earliest state that
has OPAL_PM_LOSE_FULL_CONTEXT set, in other places the kernel uses the
"deep" states as terminology. Hence renaming the variable to be coherent
to its semantics.
Signed-off-by: Pratik Rajesh Sampat <psampat@linux.ibm.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200721153708.89057-3-psampat@linux.ibm.com
The POWER9 idle driver contains implementation-specific details that
means it is not suitable to run on any processor that implements ISA
v3.0 (e.g., POWER10), so only init the driver when running on a
POWER9.
Signed-off-by: Pratik Rajesh Sampat <psampat@linux.ibm.com>
[mpe: Use updated change log from Nick]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200721153708.89057-2-psampat@linux.ibm.com
PowerISA v3.1 has few updates for the Branch History Rolling
Buffer(BHRB).
BHRB disable is controlled via Monitor Mode Control Register A (MMCRA)
bit, namely "BHRB Recording Disable (BHRBRD)". This field controls
whether BHRB entries are written when BHRB recording is enabled by
other bits. This patch implements support for this BHRB disable bit.
By setting 0b1 to this bit will disable the BHRB and by setting 0b0 to
this bit will have BHRB enabled. This addresses backward
compatibility (for older OS), since this bit will be cleared and
hardware will be writing to BHRB by default.
This patch addresses changes to set MMCRA (BHRBRD) at boot for
power10 (there by the core will run faster) and enable this feature
only on runtime ie, on explicit need from user. Also save/restore
MMCRA in the restore path of state-loss idle state to make sure we
keep BHRB disabled if it was not enabled on request at runtime.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1594996707-3727-12-git-send-email-atrajeev@linux.vnet.ibm.com
To enable memory unplug without splitting kernel page table
mapping, we force the max mapping size to the LMB size. LMB
size is the unit in which hypervisor will do memory add/remove
operation.
Pseries systems supports max LMB size of 256MB. Hence on pseries,
we now end up mapping memory with 2M page size instead of 1G. To improve
that we want hypervisor to hint the kernel about the hotplug
memory range. That was added that as part of
commit b6eca183e2 ("powerpc/kernel: Enables memory
hot-remove after reboot on pseries guests")
But PowerVM doesn't provide that hint yet. Once we get PowerVM
updated, we can then force the 2M mapping only to hot-pluggable
memory region using memblock_is_hotpluggable(). Till then
let's depend on LMB size for finding the mapping page size
for linear range.
With this change KVM guest will also be doing linear mapping with
2M page size.
The actual TLB benefit of mapping guest page table entries with
hugepage size can only be materialized if the partition scoped
entries are also using the same or higher page size. A guest using
1G hugetlbfs backing guest memory can have a performance impact with
the above change.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Fold in fix from Aneesh spotted by lkp@intel.com]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200709131925.922266-5-aneesh.kumar@linux.ibm.com
P9 DD2 NX workbook (Table 4-36) says DMA controller uses CC=5
internally for translation fault handling. NX reserves CC=250 for
OS to notify user space when NX encounters address translation
failure on the request buffer. Not an issue in earlier releases
as NX does not get faults on kernel addresses.
This patch defines CSB_CC_FAULT_ADDRESS(250) and updates CSB.CC with
this proper error code for user space.
Fixes: c96c4436ab ("powerpc/vas: Update CSB and notify process for fault CRBs")
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
[mpe: Added Fixes tag and fix typo in comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/019fd53e7538c6f8f332d175df74b1815ef5aa8c.camel@linux.ibm.com
pnv_ioda_setup_bus_dma() is only used when a passed through PE is
returned to the host. If the kernel is built without IOMMU support
this is dead code. Move it under the #ifdef with the rest of the
IOMMU API support.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200705133557.443607-2-oohall@gmail.com
The kernel test robot noticed these are non-static which causes Clang to
print some warnings. These are called via ppc_md function pointers so
there's no need for them to be non-static.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200705133557.443607-1-oohall@gmail.com
The iommu_table_ops::xchg_no_kill() callback updates TCE. It is quite
possible that not entire table is allocated if it is huge and multilevel
so xchg may also allocate subtables. If failed, it returns H_HARDWARE
for failed allocation and H_TOO_HARD if it needs it but cannot do because
the alloc parameter is "false" (set when called with MMU=off to force
retry with MMU=on).
The problem is that having separate errors only matters in real mode
(MMU=off) but the only caller with alloc="false" does not check the exact
error code and simply returns H_TOO_HARD; and for every other mode
alloc is "true". Also, the function is also called from the ioctl()
handler of the VFIO SPAPR TCE IOMMU subdriver which does not expect
hypervisor error codes (H_xxx) and will expose them to the userspace.
This converts wrong error codes to -ENOMEM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200617003835.48831-1-aik@ozlabs.ru
Switch the function documentation to kerneldoc comments, and add
WARN_ON_ONCE asserts that the calling thread is a kernel thread and does
not have ->mm set (or has ->mm set in the case of unuse_mm).
Also give the functions a kthread_ prefix to better document the use case.
[hch@lst.de: fix a comment typo, cover the newly merged use_mm/unuse_mm caller in vfio]
Link: http://lkml.kernel.org/r/20200416053158.586887-3-hch@lst.de
[sfr@canb.auug.org.au: powerpc/vas: fix up for {un}use_mm() rename]
Link: http://lkml.kernel.org/r/20200422163935.5aa93ba5@canb.auug.org.au
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [usb]
Acked-by: Haren Myneni <haren@linux.ibm.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Link: http://lkml.kernel.org/r/20200404094101.672954-6-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to make it
safe against parallel page table manipulations without relying on an IPI for
serialisation.
- A series of fixes & enhancements to make our machine check handling more
robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions on
Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan, Andrey Abramov,
Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent Abali, Cédric Le
Goater, Chen Zhou, Christian Zigotzky, Christophe JAILLET, Christophe Leroy,
Dmitry Torokhov, Emmanuel Nicolet, Erhard F., Gautham R. Shenoy, Geoff Levand,
George Spelvin, Greg Kurz, Gustavo A. R. Silva, Gustavo Walbon, Haren Myneni,
Hari Bathini, Joel Stanley, Jordan Niethe, Kajol Jain, Kees Cook, Leonardo
Bras, Madhavan Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Michal Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram
Pai, Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler, Wolfram
Sang, Xiongfeng Wang.
-----BEGIN PGP SIGNATURE-----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=o0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to
make it safe against parallel page table manipulations without
relying on an IPI for serialisation.
- A series of fixes & enhancements to make our machine check handling
more robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions
on Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound
driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Andrey Abramov, Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent
Abali, Cédric Le Goater, Chen Zhou, Christian Zigotzky, Christophe
JAILLET, Christophe Leroy, Dmitry Torokhov, Emmanuel Nicolet, Erhard F.,
Gautham R. Shenoy, Geoff Levand, George Spelvin, Greg Kurz, Gustavo A.
R. Silva, Gustavo Walbon, Haren Myneni, Hari Bathini, Joel Stanley,
Jordan Niethe, Kajol Jain, Kees Cook, Leonardo Bras, Madhavan
Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Michal
Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin,
Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram Pai,
Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler,
Wolfram Sang, Xiongfeng Wang.
* tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (299 commits)
powerpc/pseries: Make vio and ibmebus initcalls pseries specific
cxl: Remove dead Kconfig options
powerpc: Add POWER10 architected mode
powerpc/dt_cpu_ftrs: Add MMA feature
powerpc/dt_cpu_ftrs: Enable Prefixed Instructions
powerpc/dt_cpu_ftrs: Advertise support for ISA v3.1 if selected
powerpc: Add support for ISA v3.1
powerpc: Add new HWCAP bits
powerpc/64s: Don't set FSCR bits in INIT_THREAD
powerpc/64s: Save FSCR to init_task.thread.fscr after feature init
powerpc/64s: Don't let DT CPU features set FSCR_DSCR
powerpc/64s: Don't init FSCR_DSCR in __init_FSCR()
powerpc/32s: Fix another build failure with CONFIG_PPC_KUAP_DEBUG
powerpc/module_64: Use special stub for _mcount() with -mprofile-kernel
powerpc/module_64: Simplify check for -mprofile-kernel ftrace relocations
powerpc/module_64: Consolidate ftrace code
powerpc/32: Disable KASAN with pages bigger than 16k
powerpc/uaccess: Don't set KUEP by default on book3s/32
powerpc/uaccess: Don't set KUAP by default on book3s/32
powerpc/8xx: Reduce time spent in allow_user_access() and friends
...
pnv_pci_ioda_configure_bus() should now only ever be called when a device is
added to the bus so add a WARN_ON() to the empty bus check. Similarly,
pnv_pci_ioda_setup_bus_PE() should only ever be called for an unconfigured PE,
so add a WARN_ON() for that case too.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200417073508.30356-5-oohall@gmail.com
Doing it once during boot rather than doing it on the fly and drop the janky
populated logic.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200417073508.30356-4-oohall@gmail.com
For normal PHBs IODA PEs are handled on a per-bus basis so all the devices
on that bus will share a PE. Which PE specificly is determined by the location
of the MMIO BARs for the devices on the bus so we can't actually configure the
bus PEs until after MMIO resources are allocated. As a result PEs are currently
configured by pcibios_setup_bridge(), which is called just before the bridge
windows are programmed into the bus' parent bridge. Configuring the bus PE here
causes a few problems:
1. The root bus doesn't have a parent bridge so setting up the PE for the root
bus requires some hacks.
2. The PELT-V isn't setup correctly because pnv_ioda_set_peltv() assumes that
PEs will be configured in root-to-leaf order. This assumption is broken
because resource assignment is performed depth-first so the leaf bridges
are setup before their parents are. The hack mentioned in 1) results in
the "correct" PELT-V for busses immediately below the root port, but not
for devices below a switch.
3. It's possible to break the sysfs PCI rescan feature by removing all
the devices on a bus. When the last device is removed from a PE its
will be de-configured. Rescanning the devices on a bus does not cause
the bridge to be reconfigured rendering the devices on that bus
unusable.
We can address most of these problems by moving the PE setup out of
pcibios_setup_bridge() and into pcibios_bus_add_device(). This fixes 1)
and 2) because pcibios_bus_add_device() is called on each device in
root-to-leaf order so PEs for parent buses will always be configured
before their children. It also fixes 3) by ensuring the PE is
configured before initialising DMA for the device. In the event the PE
was de-configured due to removing all the devices in that PE it will
now be reconfigured when a new device is added since there's no
dependecy on the bridge_setup() hook being called.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200417073508.30356-3-oohall@gmail.com
For each PHB we maintain a reverse-map that can be used to find the
PE that a BDFN is currently mapped to. Add a helper for doing this
lookup so we can check if a PE has been configured without looking
at pdn->pe_number.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200417073508.30356-2-oohall@gmail.com
It's pretty obsecure and confused me for a long time so I figured it's
worth documenting properly.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200414233502.758-1-oohall@gmail.com
Quite useful to know in some cases.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200408112213.5549-1-oohall@gmail.com
The NVlink IOMMU group setup is only relevant to NVLink devices so move
it into the NPU containment zone. This let us remove some prototypes in
pci.h and staticfy some function definitions.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200406030745.24595-8-oohall@gmail.com
Move it in with the rest of the TCE wrangling rather than carting around
a static prototype in pci-ioda.c
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200406030745.24595-7-oohall@gmail.com
Pratik Rajesh Sampat