Make use of for_each_requested_gpio() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615150545.87964-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds the possibility to configure a single pin through the gpiolib (i.e:
to set PULL_UP/PULL_DOWN config).
Mutex behavior is slightly changed to avoid a deadlock when pin_config_set
is called (in this case pctldev->mutex is already taken).
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20200615125951.28008-3-alexandre.torgue@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
".pin_config_set" or ".pin_config_group_set" can be called with a
configuration not supported (i.e. PIN_CONFIG_PERSIST_STATE). In this case,
it is more suitable to return -ENOTSUPP instead of -EINVAL.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20200615125951.28008-2-alexandre.torgue@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Defer probe when pin controller reset is defined in the system resources
but not yet probed.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20200615125407.27632-3-alexandre.torgue@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change STM32 pinctrl driver to not print an error trace when probe is
deferred due to clock resource. Probe defer issue (for clocks) could
occur during bank registering when some banks have already been registered.
In this case banks already registered should be released. To not waste time
in this case, it is better to check first if all clocks are available
before registering banks.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20200615125407.27632-2-alexandre.torgue@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a compatible string to support the GPIO chips on the JZ4725B SoC.
There was already a compatible string for the pinctrl node, but not for
the individual GPIO chip nodes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200612120609.12730-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the correct the function name in the documentation for
"pcs_parse_one_pinctrl_entry()".
"smux_parse_one_pinctrl_entry()" appears to be an artifact from the
development of a prior patch series ("simple pinmux driver") which
transformed into pinctrl-single.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20200612112758.GA3407886@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch adds missing qpic data pins to qpic pingroup. These pins are
necessary for the qpic nand to work.
Fixes: ef1ea54eab ("pinctrl: qcom: Add ipq6018 pinctrl driver")
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1592541089-17700-1-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit ba40324261.
After commit 26d8cde526 ("pinctrl: freescale: imx: add shared
input select reg support"). i.MX7D has two iomux controllers
iomuxc and iomuxc-lpsr which share select_input register for
daisy chain settings.
If use 'devm_of_iomap()', when probe the iomuxc-lpsr, will call
devm_request_mem_region() for the region <0x30330000-0x3033ffff>
for the first time. Then, next time when probe the iomuxc, API
devm_platform_ioremap_resource() will also use the API
devm_request_mem_region() for the share region <0x30330000-0x3033ffff>
again, then cause issue, log like below:
[ 0.179561] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
[ 0.191742] imx7d-pinctrl 30330000.pinctrl: can't request region for resource [mem 0x30330000-0x3033ffff]
[ 0.191842] imx7d-pinctrl: probe of 30330000.pinctrl failed with error -16
Fixes: ba40324261 ("pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1591673223-1680-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no
pinctrl_map is added. The current behavior is to return 0 when
!PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry()
incorrectly assumes that a map was added and sets num_maps = 2.
Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf()
if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf()
returns 0 to indicate there was no error and num_maps is then set to 2:
980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
981 struct device_node *np,
982 struct pinctrl_map **map,
983 unsigned *num_maps,
984 const char **pgnames)
985 {
<snip>
1053 (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054 (*map)->data.mux.group = np->name;
1055 (*map)->data.mux.function = np->name;
1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }
However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or
!nconfs. I believe these conditions should indicate that no map was
added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry()
will set num_maps = 2 even though no maps were successfully added, as
it does not reach "m++" on line 940:
895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;
938 func->nconfs = nconfs;
939 conf = &(func->conf[0]);
940 m++;
This situtation will cause a boot failure [0] on the BeagleBone Black
(AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi
has compatible = "pinconf-single" instead of "pinctrl-single".
The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF
or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no
map was added.
Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish
between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps
is set to 1 as it is valid for pinconf to be enabled and a given pin
group to not any pinconf properties.
[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/
Fixes: 9dddb4df90 ("pinctrl: single: support generic pinconf")
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200608125143.GA2789203@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the FRE/FWE pins for the JZ4740.
These pins must be in function #0 for the NAND to work. The reason it
worked before was because the bootloader did set these pins to the
correct function beforehand.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200607174243.2361664-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/pinctrl/pinctrl-mcp23s08_spi.c:129:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Fixes: 0f04a81784 ("pinctrl: mcp23s08: Split to three parts: core, I²C, SPI")
Signed-off-by: kernel test robot <lkp@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200608010253.GA79576@44f7ab9e8d59
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use noirq suspend/resume callbacks as other drivers which implement
noirq suspend/resume callbacks (Ex:- PCIe) depend on pinctrl driver to
configure the signals used by their respective devices in the noirq phase.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200604174935.26560-1-vidyas@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following warnings caused by reusage of the same irq_chip
instance for all spmi-gpio gpio_irq_chip instances. Instead embed
irq_chip into pmic_gpio_state struct.
gpio gpiochip2: (c440000.qcom,spmi:pmic@2:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip3: (c440000.qcom,spmi:pmic@4:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip4: (c440000.qcom,spmi:pmic@a:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200604002817.667160-1-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211.
-----BEGIN PGP SIGNATURE-----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=3UGk
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.8 kernel cycle.
It's just really boring this time. Zero core changes. Just linear
development, cleanups and misc noncritical fixes. Some new drivers for
very new Qualcomm and Intel chips.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211"
* tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sprd: Fix the incorrect pull-up definition
pinctrl: pxa: pxa2xx: Remove 'pxa2xx_pinctrl_exit()' which is unused and broken
pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'
pinctrl: freescale: imx: Fix an error handling path in 'imx_pinctrl_probe()'
pinctrl: sirf: add missing put_device() call in sirfsoc_gpio_probe()
pinctrl: imxl: Fix an error handling path in 'imx1_pinctrl_core_probe()'
pinctrl: bcm2835: Add support for wake-up interrupts
pinctrl: bcm2835: Match BCM7211 compatible string
dt-bindings: pinctrl: Document optional BCM7211 wake-up interrupts
dt-bindings: pinctrl: Document 7211 compatible for brcm, bcm2835-gpio.txt
dt-bindings: pinctrl: stm32: Add missing interrupts property
pinctrl: at91-pio4: Add COMPILE_TEST support
pinctrl: Fix return value about devm_platform_ioremap_resource()
MAINTAINERS: Renesas Pin Controllers are supported
dt-bindings: pinctrl: ocelot: Add Sparx5 SoC support
pinctrl: ocelot: Fix GPIO interrupt decoding on Jaguar2
pinctrl: ocelot: Remove instance number from pin functions
pinctrl: ocelot: Always register GPIO driver
dt-bindings: pinctrl: rockchip: update example
pinctrl: amd: Add ACPI dependency
...
Commit 6d33ee7a05 ("pinctrl: pxa: Use devm_pinctrl_register() for pinctrl registration")
has turned a 'pinctrl_register()' into 'devm_pinctrl_register()' in
'pxa2xx_pinctrl_init()'.
However, the corresponding 'pinctrl_unregister()' call in
'pxa2xx_pinctrl_exit()' has not been removed.
This is not an issue, because 'pxa2xx_pinctrl_exit()' is unused.
Remove it now to avoid some wondering in the future and save a few LoC.
Fixes: 6d33ee7a05 ("pinctrl: pxa: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/20200531073716.593343-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'pinctrl_unregister()' should not be called to undo
'devm_pinctrl_register_and_init()', it is already handled by the framework.
This simplifies the error handling paths of the probe function.
The 'imx_free_resources()' can be removed as well.
Fixes: a51c158bf0 ("pinctrl: imx: use radix trees for groups and functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20200530204955.588962-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A coccicheck run provided information like the following:
drivers/pinctrl/sirf/pinctrl-sirf.c:798:2-8: ERROR: missing put_device;
call of_find_device_by_node on line 792, but without a corresponding
object release within this function.
Generated by: scripts/coccinelle/free/put_device.cocci
Thus add a jump target to fix the exception handling for this
function implementation.
Fixes: 5130216265 ("PINCTRL: SiRF: add GPIO and GPIO irq support in CSR SiRFprimaII")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20200603013532.755220-1-yukuai3@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When 'pinctrl_register()' has been turned into 'devm_pinctrl_register()',
an error handling path has not been updated.
Axe a now unneeded 'pinctrl_unregister()'.
Fixes: e55e025d16 ("pinctrl: imxl: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200530201952.585798-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Leverage the IRQCHIP_MASK_ON_SUSPEND flag in order to avoid having to
specifically treat the GPIO interrupts during suspend and resume, and
simply implement an irq_set_wake() callback that is responsible for
enabling the parent wake-up interrupt as a wake-up interrupt.
To avoid allocating unnecessary resources for other chips, the wake-up
interrupts are only initialized if we have a brcm,bcm7211-gpio
compatibility string.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200531001101.24945-5-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BCM7211 SoC uses the same pinconf_ops as the ones defined for the
BCM2711 SoC, match the compatible string and use the correct set of
options.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200531001101.24945-4-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: 4b024225c4 ("pinctrl: use devm_platform_ioremap_resource() to simplify code")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1590234326-2194-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for the new RZ/G1H (r8a7742) SoC,
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXsU4BgAKCRCKwlD9ZEnx
cLVzAP9GTdDrxNO4d9JceM3WvhsX/JrpXOOJjgjObAZj7AtN3AEA0iXhBsIOP7lN
oiAYEWBTmaAVBvwaVWdvKT4AhLEv3wQ=
=kdu0
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.8 (take two)
- Add support for the new RZ/G1H (r8a7742) SoC,
- Minor fixes and improvements.
Two fixes for S5Pv210 pinctrl driver: setting proper external interrupt
wakeup mask and restoring external interrupt mask value after system
suspend.
-----BEGIN PGP SIGNATURE-----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=9T4z
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-5.8' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v5.8
Two fixes for S5Pv210 pinctrl driver: setting proper external interrupt
wakeup mask and restoring external interrupt mask value after system
suspend.
This fixes a problem with using the GPIO as an interrupt on Jaguar2
(and similar), as the register layout of the platforms with 64 GPIO's
are pairwise, such that the original offset must be multiplied with
the platform stride.
Fixes: da801ab56a pinctrl: ocelot: add MSCC Jaguar2 support.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-4-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes the instance number from the "miim", "reco_clk" and
"sfp" pin function.
The change needed is to prepare the driver for adding new platforms
with more of these instances. The instance number is also redundant,
as this is implicit for each pin.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-3-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes the situation where the GPIO controller is not
used as an interrupt controller as well.
Previously, the driver would silently fail to register even the
GPIO's. With this change, the driver will only register as an
interrupt controller if a parent interrupt is provided.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-2-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the AMD pin controller driver supports ACPI platform only.
Make the PINCTRL_AMD config symbol depend on ACPI, to avoid asking the
user about it when configuring a kernel without ACPI support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200507113751.24213-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Equilibrium pin controller is only present on Intel Lightning
Mountain SoCs. Add an architecture dependency to the
PINCTRL_EQUILIBRIUM config symbol, to avoid asking the user about it
when configuring a kernel for a non-x86 architecture.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200507113626.24026-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Introduce GPIO driver for Jasper Lake
* Fix long standing bug in Sunrisepoint-H PAD locking code
* Enable pin configuration setting for GPIO chip for Baytrail
* Work around race condition in Cherriview hardware when handle IRQ
* Clean up Cherryview code to be closer to other drivers
The following is an automated git shortlog grouped by driver:
baytrail:
- Use platform_get_irq_optional() explicitly
- Enable pin configuration setting for GPIO chip
cannonlake:
- Use generic flag for special GPIO base treatment
cherryview:
- Add missing spinlock usage in chv_gpio_irq_handler
- Use GENMASK() consistently
- Re-use data structures from pinctrl-intel.h (part 2)
icelake:
- Use generic flag for special GPIO base treatment
intel:
- Move npins closer to pin_base in struct intel_community
- Update description in struct intel_community
- Add Intel Jasper Lake pin controller support
- Introduce new flag to force GPIO base to be 0
- Introduce common flags for GPIO mapping scheme
lynxpoint:
- Use platform_get_irq_optional() explicitly
sunrisepoint:
- Fix PAD lock register offset for SPT-H
tigerlake:
- Use generic flag for special GPIO base treatment
-----BEGIN PGP SIGNATURE-----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=e+Dg
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.8-1
* Introduce GPIO driver for Jasper Lake
* Fix long standing bug in Sunrisepoint-H PAD locking code
* Enable pin configuration setting for GPIO chip for Baytrail
* Work around race condition in Cherriview hardware when handle IRQ
* Clean up Cherryview code to be closer to other drivers
The following is an automated git shortlog grouped by driver:
baytrail:
- Use platform_get_irq_optional() explicitly
- Enable pin configuration setting for GPIO chip
cannonlake:
- Use generic flag for special GPIO base treatment
cherryview:
- Add missing spinlock usage in chv_gpio_irq_handler
- Use GENMASK() consistently
- Re-use data structures from pinctrl-intel.h (part 2)
icelake:
- Use generic flag for special GPIO base treatment
intel:
- Move npins closer to pin_base in struct intel_community
- Update description in struct intel_community
- Add Intel Jasper Lake pin controller support
- Introduce new flag to force GPIO base to be 0
- Introduce common flags for GPIO mapping scheme
lynxpoint:
- Use platform_get_irq_optional() explicitly
sunrisepoint:
- Fix PAD lock register offset for SPT-H
tigerlake:
- Use generic flag for special GPIO base treatment
Renesas RZ/G1H (R8A7742) is pin compatible with R-Car H2 (R8A7790),
however it doesn't have several automotive specific peripherals. Add
automotive-specific pin groups/functions along with common pin
groups/functions for supporting both r8a7790 and r8a7742 SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1588542414-14826-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In function rockchip_dt_node_to_map, a new_map variable is
allocated by:
new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map),
GFP_KERNEL);
This uses devres and attaches new_map to the pinctrl driver.
This cause a leak since new_map is not released when the probed
driver is removed. Fix it by using kcalloc to allocate new_map
and free it in `rockchip_dt_free_map`
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200506100903.15420-1-dafna.hirschfeld@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kbuild warns when this file is built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.o
see include/linux/module.h for more information
Add the missing license/author/description tags.
Fixes: 8174a8512e ("pinctrl: mediatek: make MediaTek pinctrl v2 driver ready for buidling loadable module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200505140848.554957-1-arnd@arndb.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are called when a GPIO is to be used as IRQ.
Without these custom callbacks, when an interrupt is requested directly
and not through gpiod_to_irq(), the request fails because the GPIO is
not necesarily in input mode. These callbacks simply enforce that the
requested GPIO is in input mode.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200503164549.163884-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wakeup capable GPIO IRQs routed via PDC are not being migrated when a CPU
is hotplugged. Add affinity callbacks to msmgpio IRQ chip to update the
affinity of wakeup capable IRQs.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
[mkshah: updated commit text and minor code fixes]
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1588314617-4556-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Hulk robot reports these build warnings:
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:899:20: warning:
‘sbag_groups’ defined but not used [-Wunused-const-variable=]
DB8500_FUNC_GROUPS(sbag, "sbag_oc2_1", "sbag_oc4_1");
^
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:570:23: warning:
‘ipgpio6_c_2_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned ipgpio6_c_2_pins[] = { DB8500_PIN_G3 };
^~~~~~~~~~~~~~~~
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:472:23: warning:
‘mc1dir_a_1_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned mc1dir_a_1_pins[] = { DB8500_PIN_AH13,
DB8500_PIN_AG12,
^~~~~~~~~~~~~~~
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:453:23: warning:
‘modem_a_1_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned modem_a_1_pins[] = { DB8500_PIN_D22,
DB8500_PIN_C23,
^~~~~~~~~~~~~~
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:430:23: warning:
‘kpskaskb_a_1_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned kpskaskb_a_1_pins[] = { DB8500_PIN_D17,
DB8500_PIN_D16 };
^~~~~~~~~~~~~~~~~
They are just very old bugs in seldomly used pin groups.
Fix the problem by using the pins and referencing the
function.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Hulk robot reports an usused varible:
drivers/pinctrl/nomadik/pinctrl-ab8505.c:137:23: warning:
‘gpio50_a_1_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned gpio50_a_1_pins[] = { AB8505_PIN_L4 };
^~~~~~~~~~~~~~~
This variable actually should be used. Probably an oversight
by the driver author.
Cc: Patrice Chotard <patrice.chotard@st.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'pwm37' is not added to bm1880_pctrl_groups, which triggers a gcc
build warning:
drivers/pinctrl/pinctrl-bm1880.c:263:27: warning: ‘pwm37_pins’ defined
but not used [-Wunused-const-variable=]
static const unsigned int pwm37_pins[] = { 110 };
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200428115543.33379-1-yanaijie@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use gpiochip_generic_config for the gpio_chip's set_config callback so
GPIO flags like GPIO_PULL_UP or GPIO_PULL_DOWN can be used in the board
.dts descriptions.
This is required for some Meson8m2 boards where GPIO_BSD_EN provides the
"MUTE" signal and requires enabling the internal pull-up resistor.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200417183349.1283092-3-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the get_direction callback so we read the direction from the
actual GPIO controller register. This is recommended by the gpio_chip
kernel doc.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200417183349.1283092-2-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers
are saved and restored over a suspend/resume cycle. However, the
EINT_MASK registers are not.
On S5PV210 at the very least, these registers are not retained over
suspend, leading to the interrupts remaining masked upon resume and
therefore no interrupts being triggered for the device. There should
be no effect on any SoCs that do retain these registers as theoretically
we would just be re-writing what was already there.
Fixes: 7ccbc60cd9 ("pinctrl: exynos: Handle suspend/resume of GPIO EINT registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
It's common across the drivers to use the (pin_base, npins) pair to describe
community characteristics. Thus, move them in the struct intel_community
to be closer to each other.
While at it, add a blank line to cut driver usable fields from what core
reserves for itself.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It appears that most of the drivers, that are using struct intel_community,
utilize gpps rather than gpp_size. Update comment accordingly.
While here, correct the description of gpp_size, i.e. remove double space
and drop redundant 'etc.' part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The rza1l_swio_entries referred to the wrong array rza1h_swio_pins,
which was intended to be rza1l_swio_pins. So let's fix it.
This is detected by the following gcc warning:
drivers/pinctrl/pinctrl-rza1.c:401:35: warning: ‘rza1l_swio_pins’
defined but not used [-Wunused-const-variable=]
static const struct rza1_swio_pin rza1l_swio_pins[] = {
^~~~~~~~~~~~~~~
Fixes: 039bc58e73 ("pinctrl: rza1: Add support for RZ/A1L")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200417111604.19143-1-yanaijie@huawei.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
* Enable pin configuration setting for Baytrail
* Fix interrupt handling due to hardware sighting for Cherryview
* Fix PAD lock offset for Sunrisepoint-H
The following is an automated git shortlog grouped by driver:
baytrail:
- Enable pin configuration setting for GPIO chip
cherryview:
- Add missing spinlock usage in chv_gpio_irq_handler
sunrisepoint:
- Fix PAD lock register offset for SPT-H
-----BEGIN PGP SIGNATURE-----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=SMBA
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.7-2
* Enable pin configuration setting for Baytrail
* Fix interrupt handling due to hardware sighting for Cherryview
* Fix PAD lock offset for Sunrisepoint-H
The following is an automated git shortlog grouped by driver:
baytrail:
- Enable pin configuration setting for GPIO chip
cherryview:
- Add missing spinlock usage in chv_gpio_irq_handler
sunrisepoint:
- Fix PAD lock register offset for SPT-H
According to Braswell NDA Specification Update (#557593),
concurrent read accesses may result in returning 0xffffffff and write
instructions may be dropped. We have an established format for the
commit references, i.e.
cdca06e4e8 ("pinctrl: baytrail: Add missing spinlock usage in
byt_gpio_irq_handler")
Fixes: 0bd50d719b ("pinctrl: cherryview: prevent concurrent access to GPIO controllers")
Signed-off-by: Grace Kao <grace.kao@intel.com>
Reported-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
According to Braswell NDA Specification Update (#557593),
concurrent read accesses may result in returning 0xffffffff and write
instructions may be dropped. We have an established format for the
commit references, i.e.
cdca06e4e8 ("pinctrl: baytrail: Add missing spinlock usage in
byt_gpio_irq_handler")
Fixes: 0bd50d719b ("pinctrl: cherryview: prevent concurrent access to GPIO controllers")
Signed-off-by: Grace Kao <grace.kao@intel.com>
Reported-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fix the following build warning:
WARNING: modpost: missing MODULE_LICENSE() in
drivers/pinctrl/pinctrl-mcp23s08.o
see include/linux/module.h for more information
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200417092125.12513-1-yanaijie@huawei.com
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to repeat functionality of platform_get_irq_optional()
in the driver. Replace it with explicit call to the helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200407173849.43628-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Return error code from device_property_read_u32() as is in mcp23s08_probe().
While here, drop status variable in mcp23s08_irq_set_type() which always 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200407173849.43628-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a lot of duplication for one small helper function.
Refactor mcp23s08_spi_regmap_init() to prepare everything first
and then register regmap at the end.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200407173849.43628-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are three parts of each, SPI and I²C, driver spread over the code under
ifdeffery. Consolidate them so it will be only one for SPI and one for I²C.
The code has been cosmetically changed to avoid intrusive change.
Clean up is considered in the nearest future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200407173849.43628-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In both cases, SPI and I²C, IRQ chip is filled in the same way.
Deduplicate this by moving common part to mcp23s08_probe_one().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200407173849.43628-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Platform data is a legacy interface to supply device properties
to the driver. In this case we even don't have in-kernel users
for it. Just remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200407173849.43628-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i.MX8DXL contains a system controller that is responsible for controlling
the pad setting of the IPs that are present. Communication between the
host processor running an OS and the system controller happens through
a SCU protocol, add support for the SCU based i.MX8DXL pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1585306559-13973-2-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix a typo in the readl/writel accessor conversion where val is used
instead of pol changing the behavior of the original code.
Cc: stable@vger.kernel.org
Fixes: 6c73698904 pinctrl: qcom: Introduce readl/writel accessors
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200414003726.25347-1-ansuelsmth@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 6f87359e8b ("pinctrl: actions: Fix functions groups names
for S700 SoC") following error has been observed while booting Linux on
Cubieboard7-lite(based on S700 SoC).
[ 1.206245] pinctrl-s700 e01b0000.pinctrl: invalid group "i2c0_mfp" for function "i2c0"
This commit fixes it by using correct name for i2c0_group.
Fixes: 6f87359e8b ("pinctrl: actions: Fix functions groups names for S700 SoC")
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Link: https://lore.kernel.org/r/1586757913-5438-1-git-send-email-amittomer25@gmail.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When checking the logs on my sun8i-a33-olinuxino I saw:
sun8i-a23-r-pinctrl 1f02c00.pinctrl: Reset controller missing
but this driver was working after.
This message is just here because the reset controller was still not probed.
So don't say anything if the return code say to wait.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1585818532-23051-1-git-send-email-clabbe@baylibre.com
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the future we want to be able to build the MediaTek pinctrl driver,
based on paris, as kernel module. This patch allows pinctrl-paris.c, the
external interrupt controller mtk-eint.c, and pinctrl-mtk-common-v2.c to
be loadable as module.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/9feeb04805e5a406fe22a92e3f280abda39ddda4.1586289920.git.sean.wang@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to repeat functionality of platform_get_irq_optional()
in the driver. Replace it with explicit call to the helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This driver adds pinctrl/GPIO support for Intel Jasper Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases not the first group would like to have GPIO base to be 0.
It's not possible right now due to 0 has special meaning already. Thus,
introduce a new flag to allow drivers to force GPIO base to be 0 on
a certain group. It's assumed that it can be only one group per device
with such flag enabled.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Few drivers are using the same flag to tell Intel pin control core
how to interpret GPIO base.
Provide a generic flags so all drivers can use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Baytrail.
Fixes: c501d0b149 ("pinctrl: baytrail: Add pin control operations")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It appears that SPT-H variant has different offset for PAD locking registers.
Fix it here.
Fixes: 551fa5801e ("pinctrl: intel: sunrisepoint: Add Intel Sunrisepoint-H support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit a8be2af021 ("pinctrl: samsung: Write external wakeup interrupt
mask") started writing the eint wakeup mask from the pinctrl driver.
Unfortunately, it made the assumption that the private retention data
was always a regmap while in the case of s5pv210 it is a raw pointer
to the clock base (as the eint wakeup mask not in the PMU as with newer
Exynos platforms).
Fixes: a8be2af021 ("pinctrl: samsung: Write external wakeup interrupt mask")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Core and userspace API:
- The userspace API KFIFOs have been imoproved with locks that
do not block interrupts. This makes us better at getting
events to userspace without blocking or disturbing new events
arriving in the same time. This was reviewed by the KFIFO
maintainer Stefani. This is a generic improvement which
paves the road for similar improvements in other subsystems.
- We provide a new ioctl() for monitoring changes in the line
information, such as when multiple clients are taking lines
and giving them back, possibly reconfiguring them in the
process: we can now monitor that and not get stuck with stale
static information.
- An example tool 'gpio-watch' is provided to showcase this
functionality.
- Timestamps for events are switched to ktime_get_ns() which is
monotonic. We previously had a 'realtime' stamp which could
move forward and *backward* in time, which probably would just
cause silent bugs and weird behaviour. In the long run we
see two relevant timestamps: ktime_get_ns() or the timestamp
sometimes provided by the GPIO hardware itself, if that
exists.
- Device Tree overlay support for GPIO hogs. On systems that
load overlays, these overlays can now contain hogs, and will
then be respected.
- Handle pin control interaction with nonexisting pin ranges
in the GPIO library core instead of in the individual
drivers.
New drivers:
- New driver for the Mellanox BlueField 2 GPIO controller.
Driver improvements:
- Introduce the BGPIOF_NO_SET_ON_INPUT flag to the generic
MMIO GPIO library and use this flag in the MT7621 driver.
- Texas Instruments OMAP CPU power management improvements,
such as blocking of idle on pending GPIO interrupts.
-----BEGIN PGP SIGNATURE-----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=EFm/
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO development for the v5.7 kernel cycle.
Core and userspace API:
- The userspace API KFIFOs have been imoproved with locks that do not
block interrupts. This makes us better at getting events to
userspace without blocking or disturbing new events arriving in the
same time. This was reviewed by the KFIFO maintainer Stefani. This
is a generic improvement which paves the road for similar
improvements in other subsystems.
- We provide a new ioctl() for monitoring changes in the line
information, such as when multiple clients are taking lines and
giving them back, possibly reconfiguring them in the process: we
can now monitor that and not get stuck with stale static
information.
- An example tool 'gpio-watch' is provided to showcase this
functionality.
- Timestamps for events are switched to ktime_get_ns() which is
monotonic. We previously had a 'realtime' stamp which could move
forward and *backward* in time, which probably would just cause
silent bugs and weird behaviour. In the long run we see two
relevant timestamps: ktime_get_ns() or the timestamp sometimes
provided by the GPIO hardware itself, if that exists.
- Device Tree overlay support for GPIO hogs. On systems that load
overlays, these overlays can now contain hogs, and will then be
respected.
- Handle pin control interaction with nonexisting pin ranges in the
GPIO library core instead of in the individual drivers.
New drivers:
- New driver for the Mellanox BlueField 2 GPIO controller.
Driver improvements:
- Introduce the BGPIOF_NO_SET_ON_INPUT flag to the generic MMIO GPIO
library and use this flag in the MT7621 driver.
- Texas Instruments OMAP CPU power management improvements, such as
blocking of idle on pending GPIO interrupts"
* tag 'gpio-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (59 commits)
Revert "gpio: eic-sprd: Use devm_platform_ioremap_resource()"
pinctrl: Unconditionally assign .request()/.free()
gpio: Unconditionally assign .request()/.free()
gpio: export of_pinctrl_get to modules
pinctrl: Define of_pinctrl_get() dummy for !PINCTRL
gpio: Rename variable in core APIs
gpio: Avoid using pin ranges with !PINCTRL
gpiolib: Remove unused gpio_chip parameter from gpio_set_bias()
gpiolib: Pass gpio_desc to gpio_set_config()
gpiolib: Introduce gpiod_set_config()
tools: gpio: Fix out-of-tree build regression
gpio: gpiolib: fix a doc warning
gpio: tegra186: Add Tegra194 pin ranges for GG.0 and GG.1
gpio: tegra186: Add support for pin ranges
gpio: Support GPIO controllers without pin-ranges
ARM: integrator: impd1: Use GPIO_LOOKUP() helper macro
gpio: brcmstb: support gpio-line-names property
tools: gpio: Fix typo in gpio-utils
tools: gpio-hammer: Apply scripts/Lindent and retain good changes
gpiolib: gpio_name_to_desc: factor out !name check
...
There are no core changes this time, only driver developments.
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and
register checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek
driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs
that exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the
new and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194
SoC driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver.
-----BEGIN PGP SIGNATURE-----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=1ZKq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.7 kernel cycle.
There are no core changes this time, only driver developments:
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and register
checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs that
exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the new
and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194 SoC
driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver"
* tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (64 commits)
pinctrl: qcom: fix compilation error
pinctrl: qcom: use scm_call to route GPIO irq to Apps
pinctrl: sprd: Add pin high impedance mode support
pinctrl: sprd: Use the correct pin output configuration
pinctrl: tegra: Add SFIO/GPIO programming on Tegra194
pinctrl: tegra: Renumber the GG.0 and GG.1 pins
pinctrl: tegra: Do not add default pin range on Tegra194
pinctrl: tegra: Pass struct tegra_pmx for pin range check
pinctrl: tegra: Fix "Scmitt" -> "Schmitt" typo
pinctrl: tegra: Fix whitespace issues for improved readability
pinctrl: mediatek: Use scnprintf() for avoiding potential buffer overflow
pinctrl: freescale: drop the dependency on ARM64 for i.MX8M
Revert "pinctrl: mvebu: armada-37xx: use use platform api"
dt-bindings: pinctrl: at91: Fix a typo ("descibe")
pinctrl: meson: add tsin pinctrl for meson gxbb/gxl/gxm
pinctrl: sprd: Fix the kconfig warning
pinctrl: ingenic: add hdmi-ddc pin control group
pinctrl: sirf/atlas7: Replace zero-length array with flexible-array member
pinctrl: sprd: Allow the SPRD pinctrl driver building into a module
pinctrl: Export some needed symbols at module load time
...
The gpiochip_generic_request() and gpiochip_generic_free() functions can
now deal properly with chips that don't have any pin-ranges defined, so
they can be assigned unconditionally.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200401200527.2982450-2-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: qcom: use scm_call to route GPIO irq to Apps has a typo in the
patch and introduced a compilation error.
Fixes: 13bec8d4 pinctrl: qcom: use scm_call to route GPIO irq to Apps
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20200331134603.13513-1-ansuelsmth@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early. Most cleanup changes come
through the various maintainer trees, so the final removal of
setup_irq() is postponed towards the end of the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and unsafe
interrupt injection including a fixup of the offending PCI/AER error
injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside of
an actual interrupt, can cause inconsistent state on the fragile
x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=DZ/G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early.
Most cleanup changes come through the various maintainer trees, so
the final removal of setup_irq() is postponed towards the end of
the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and
unsafe interrupt injection including a fixup of the offending
PCI/AER error injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside
of an actual interrupt, can cause inconsistent state on the
fragile x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place"
* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
unicore32: Replace setup_irq() by request_irq()
sh: Replace setup_irq() by request_irq()
hexagon: Replace setup_irq() by request_irq()
c6x: Replace setup_irq() by request_irq()
alpha: Replace setup_irq() by request_irq()
irqchip/gic-v4.1: Eagerly vmap vPEs
irqchip/gic-v4.1: Add VSGI property setup
irqchip/gic-v4.1: Add VSGI allocation/teardown
irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
irqchip/gic-v4.1: Add initial SGI configuration
irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
irqchip/stm32: Retrigger both in eoi and unmask callbacks
irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
irqchip/xilinx: Do not call irq_set_default_host()
irqchip/xilinx: Enable generic irq multi handler
irqchip/xilinx: Fill error code when irq domain registration fails
irqchip/xilinx: Add support for multiple instances
...
Here is the "big" set of driver core changes for 5.7-rc1.
Nothing huge in here, just lots of little firmware core changes and use
of new apis, a libfs fix, a debugfs api change, and some driver core
deferred probe rework.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHLIg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yle2ACgjJJzRJl9Ckae3ms+9CS4OSFFZPsAoKSrXmFc
Z7goYQdZo1zz8c0RYDrJ
=Y91m
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core changes for 5.7-rc1.
Nothing huge in here, just lots of little firmware core changes and
use of new apis, a libfs fix, a debugfs api change, and some driver
core deferred probe rework.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (44 commits)
Revert "driver core: Set fw_devlink to "permissive" behavior by default"
driver core: Set fw_devlink to "permissive" behavior by default
driver core: Replace open-coded list_last_entry()
driver core: Read atomic counter once in driver_probe_done()
libfs: fix infoleak in simple_attr_read()
driver core: Add device links from fwnode only for the primary device
platform/x86: touchscreen_dmi: Add info for the Chuwi Vi8 Plus tablet
platform/x86: touchscreen_dmi: Add EFI embedded firmware info support
Input: icn8505 - Switch to firmware_request_platform for retreiving the fw
Input: silead - Switch to firmware_request_platform for retreiving the fw
selftests: firmware: Add firmware_request_platform tests
test_firmware: add support for firmware_request_platform
firmware: Add new platform fallback mechanism and firmware_request_platform()
Revert "drivers: base: power: wakeup.c: Use built-in RCU list checking"
drivers: base: power: wakeup.c: Use built-in RCU list checking
component: allow missing unbind callback
debugfs: remove return value of debugfs_create_file_size()
debugfs: Check module state before warning in {full/open}_proxy_open()
firmware: fix a double abort case with fw_load_sysfs_fallback
arch_topology: Fix putting invalid cpu clk
...
For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.
Signed-off-by: Ajay Kishore <akisho@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20200327223209.20409-1-ansuelsmth@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For Spreadtrum pin controller, it will be the high impedance
mode if disable input and output mode for a pin. Thus add
PIN_CONFIG_BIAS_HIGH_IMPEDANCE configuration to support it.
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/3bdac4c2673b54c940e511f3fa569ee33b87b8d5.1585124562.git.baolin.wang7@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Spreadtrum pin controller did not supply registers to set high level
or low level for output mode, instead we should let the pin controller
current configuration drive values on the line. So we should use the
PIN_CONFIG_OUTPUT_ENABLE configuration to enable or disable the output
mode.
[Baolin Wang changes the commit message]
Fixes: 41d32cfce1 ("pinctrl: sprd: Add Spreadtrum pin control driver")
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/8a6f91b49c17beb218e46b23084f59a7c7260f86.1585124562.git.baolin.wang7@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Prior to Tegra186, the selection of SFIO vs. GPIO modes was done as part
of the GPIO controller's register programming. Starting with Tegra186, a
pin is configured as GPIO or SFIO with a bit in a configuration register
of the pin controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-10-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to define these at a specific offset since they are the
only pins defined for this SoC generation. Begin numbering them at 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-9-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Tegra194, almost all of the pin control programming happens in early
boot firmware, so there is no use in having a pin range defined for all
the pins.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-8-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pass the struct tegra_pmx when checking for the pin range in device
tree. This makes the call site a bit easier to read and will help keep
that readability in a subsequent patch.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-7-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix a few whitespace inconsistencies to make the code easier to read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-5-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311090644.20287-1-tiwai@suse.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Moving to support aarch32 mode on aarch64 hardware, need to drop
the dependency on ARM64 to make the driver could be selected for
ARM32.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1584070036-26447-2-git-send-email-peng.fan@nxp.com
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sampling the IRQ line state in EOI and retriggering the interrupt to
work around missing level-triggered interrupt support only works for
non-threaded interrupts. Threaded interrupts must be retriggered the
same way in unmask callback.
Signed-off-by: Marek Vasut <marex@denx.de>
[maz: fixed missing static attribute]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200323235132.530550-1-marex@denx.de
The hierarchical parts of MSM pinctrl/GPIO is only
used when the device tree has a "wakeup-parent" as
a phandle, but the .irq_eoi is anyway assigned leading
to semantic problems on elder Qualcomm chipsets.
When the drivers/mfd/qcom-pm8xxx.c driver calls
chained_irq_exit() that call will in turn call chip->irq_eoi()
which is set to irq_chip_eoi_parent() by default on a
hierachical IRQ chip, and the parent is pinctrl-msm.c
so that will in turn unconditionally call
irq_chip_eoi_parent() again, but its parent is invalid
so we get the following crash:
Unnable to handle kernel NULL pointer dereference at
virtual address 00000010
pgd = (ptrval)
[00000010] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(...)
PC is at irq_chip_eoi_parent+0x4/0x10
LR is at pm8xxx_irq_handler+0x1b4/0x2d8
If we solve this crash by avoiding to call up to
irq_chip_eoi_parent(), the machine will hang and get
reset by the watchdog, because of semantic issues,
probably inside irq_chip.
As a solution, just assign the .irq_eoi conditionally if
we are actually using a wakeup parent.
Cc: David Heidelberg <david@ixit.cz>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: stable@vger.kernel.org
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Link: https://lore.kernel.org/r/20200306121221.1231296-1-linus.walleij@linaro.org
Link: https://lore.kernel.org/r/20200309125207.571840-1-linus.walleij@linaro.org
Link: https://lore.kernel.org/r/20200309152604.585112-1-linus.walleij@linaro.org
Tested-by: David Heidelberg <david@ixit.cz>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are parsing SSBI gpios as fourcell fwspecs but they are
twocell. Probably a simple copy-and-paste bug.
Tested on the APQ8060 DragonBoard and after this ethernet
and MMC card detection works again.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org
Reviewed-by: Brian Masney <masneyb@onstation.org>
Fixes: ae436fe810 ("pinctrl: ssbi-gpio: convert to hierarchical IRQ helpers in gpio core")
Link: https://lore.kernel.org/r/20200306143416.1476250-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO hardware block is directly linked to EXTI block but EXTI handles
external interrupts only on edge. To be able to handle GPIO interrupt on
level a "hack" is done in gpio irq chip: parent interrupt (exti irq chip)
is retriggered following interrupt type and gpio line value.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200219143229.18084-3-alexandre.torgue@st.com
With the earlier sanity fixes to
driver_deferred_probe_check_state() it should be usable for the
pinctrl logic here.
So tweak the logic to use driver_deferred_probe_check_state()
instead of driver_deferred_probe_check_state_continue()
Cc: linux-pm@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200225050828.56458-4-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On X86 plaform, if the CONFIG_OF is not selected, and set the
CONFIG_SPRD_SC9860 as 'm', that will cause below waring:
WARNING: unmet direct dependencies detected for PINCTRL_SPRD
Depends on [n]: PINCTRL [=y] && OF [=n] && (ARCH_SPRD || COMPILE_TEST [=y])
Selected by [m]:
- PINCTRL_SPRD_SC9860 [=m] && PINCTRL [=y]
Thus move the configuration dependency under CONFIG_PINCTRL_SPRD_SC9860
to fix the warning.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/eeb12d7843fb06f80e19f98eb25711231c3b610f.1583205650.git.baolin.wang7@gmail.com
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register_mappings is called in the pdata case, however a call to
pinctrl_unregister_mappings is missing causing the mappings to be leaked
on driver unbind. Add the missing call to correct this issue.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154214.13916-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kref_init starts with the reference count at 1, which will be balanced
by the pinctrl_put in pinctrl_unregister. The additional kref_get in
pinctrl_claim_hogs will increase this count to 2 and cause the hogs to
not get freed when pinctrl_unregister is called.
Fixes: 6118714275 ("pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154142.13860-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200227185837.GA4469@embeddedor
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These comparisons should be >= instead of > to prevent accessing one
element beyond the end of the hw->soc->pins[] array.
Fixes: 3de7deefce ("pinctrl: mediatek: Check gpio pin number and use binary search in mtk_hw_pin_field_lookup()")
Fixes: 184d8e13f9 ("pinctrl: mediatek: Add support for pin configuration dump via debugfs.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200218055247.74s2xa7veqx2do34@kili.mountain
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: b96eea718b ("pinctrl: fsl: add scu based pinctrl support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/bd7ad5fd755739a6d8d5f4f65e03b3ca4f457bd2.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the second loop of ingenic_pinconf_set(), it annotates the switch
default case as unreachable(). The annotation is technically correct,
because that same case would have resulted in an early function return
in the previous loop.
However, the compiled code is suboptimal. GCC seems to work extra hard
to ensure that the unreachable code path triggers undefined behavior.
The function would fall through to start executing whatever function
happens to be next in the compilation unit.
This is problematic because:
a) it adds unnecessary 'ensure undefined behavior' logic, and
corresponding i-cache footprint; and
b) it's less robust -- if a bug were to be introduced, falling through
to the next function would be catastrophic.
Yet another issue is that, while objtool normally understands
unreachable() annotations, there's one special case where it doesn't:
when the annotation occurs immediately after a 'ret' instruction. That
happens to be the case here because unreachable() is immediately before
the return.
Remove the unreachable() annotation and replace it with a comment. This
simplifies the code generation and changes the unreachable error path to
just silently return instead of corrupting execution.
This fixes the following objtool warning:
drivers/pinctrl/pinctrl-ingenic.o: warning: objtool: ingenic_pinconf_set() falls through to next function ingenic_pinconf_group_set()
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/bc20fdbcb826512cf76b7dfd0972740875931b19.1582212881.git.jpoimboe@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the gxl driver, the sdio cmd and clk pins are inverted. It has not caused
any issue so far because devices using these pins always take both pins
so the resulting configuration is OK.
Fixes: 0f15f500ff ("pinctrl: meson: Add GXL pinctrl definitions")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Link: https://lore.kernel.org/r/1582204512-7582-1-git-send-email-nbelin@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200217185437.GA20901@embeddedor
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0.
Main benefit is to make it easier to see which values mean IN and which
OUT. As a side effect this helps GPIO framework to change the direction
defines to something else if ever needed.
Please note that return value from get_direction call on
pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have
returned value 2 for direction INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controller hardware does not distinguish IRQs intended for
wakeup from other IRQs, so we must mask non-wakeup IRQs in software to
prevent inadvertent wakeups. This is accomplished at the irqchip level
via the IRQCHIP_MASK_ON_SUSPEND flag.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200117213340.47714-2-samuel@sholland.org
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl irqchip may be connected to an irqchip that implements the
.irq_set_wake callback, such as the R_INTC on A31 and newer sunxi SoCs.
In order for GPIOs to be able to trigger wakeup, the IRQ from the
pinctrl to the upper irqchip must also be enabled for wakeup. Since the
kernel's IRQ core already manages the "wake_depth" of each IRQ, no
additional accounting is needed in the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200117213340.47714-1-samuel@sholland.org
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_ARCH_R8A7795 was split in CONFIG_ARCH_R8A77950 and
CONFIG_ARCH_R8A77951 in commit b925adfceb ("soc: renesas: Add
ARCH_R8A7795[01] for existing R-Car H3"), so its users can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218112557.5924-1-geert+renesas@glider.be
As of commit 4adeabd042 ("pinctrl: sh-pfc: Remove hardcoded IRQ
numbers"), only a single operation needs to be performed after finding
the wanted pin. Hence decrease the needed attention span of the casual
reader by replacing the goto by a direct return.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200212090200.11106-1-geert+renesas@glider.be
Add checks for legacy function GPIO descriptors:
1. Function GPIOs must have a name,
2. Names must be unique,
3. Enum ID values must be unique.
This exposes bugs like those fixed in
- commit 884caadad1 ("pinctrl: sh-pfc: sh7734: Fix duplicate
TCLK1_B"),
- commit 55b1cb1f03 ("pinctrl: sh-pfc: sh7264: Fix CAN function
GPIOs"),
- commit 02aeb2f215 ("pinctrl: sh-pfc: sh7269: Fix CAN function
GPIOs"),
- commit db9c07272c ("sh: sh7264: Remove bogus SSU GPIO function
definitions"),
- commit b4fba344a2 ("sh: sh7269: Remove bogus SSU GPIO function
definitions").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-14-geert+renesas@glider.be
Add checks for data register descriptors:
1. Register addresses must be unique.
2. Enum ID values must be unique.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-13-geert+renesas@glider.be
Add checks for drive strength register descriptors:
1. Register addresses must be unique,
2. Register fields must be non-overlapping,
3. Referred pins must exist.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-10-geert+renesas@glider.be
Improve the checks for pin group descriptors:
1. Introduce a local variable for the current group, to make the
checks easier to read,
2. Pin group names must be unique.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-9-geert+renesas@glider.be
Improve the checks for pin function descriptors:
1. Merge declaration and assignment of the local variable for the
current pin function,
2. Pin function names must be unique.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-8-geert+renesas@glider.be
Improve the checks for pin descriptors:
1. Introduce local variables for the current pin, to make the checks
easier to read,
2. Pins must have a name,
3. Fix double printing of identical pin names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-7-geert+renesas@glider.be
Add a helper to verify that enum IDs are unique, and use it to validate
the enum ID arrays in config register descriptors.
This exposes bugs like those fixed in:
- commit 805f635703 ("pinctrl: sh-pfc: r8a7778: Fix duplicate
SDSELF_B and SD1_CLK_B"),
- commit 884caadad1 ("pinctrl: sh-pfc: sh7734: Fix duplicate
TCLK1_B"),
- commit 2a069a9281 ("pinctrl: sh-pfc: sh7264: Fix Port K I/O
Register 0 definition").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-6-geert+renesas@glider.be
Add a helper to verify that register addresses are unique, and use it to
validate config register descriptors.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-5-geert+renesas@glider.be
Add a helper to check if two strings are identical, skipping NULL
pointers. This simplifies callers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-4-geert+renesas@glider.be
Add helpers to report errors and warnings, and to increase the
corresponding counters. This simplifies callers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200110131927.1029-3-geert+renesas@glider.be
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c: In function mtk_hw_pin_field_lookup:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:70:39: warning:
variable e set but not used [-Wunused-but-set-variable]
Since commit 3de7deefce ("pinctrl: mediatek: Check gpio pin
number and use binary search in mtk_hw_pin_field_lookup()"),
it is not used any more, so remove it, also remove redundant
assignment to variable c, it will be assigned a new value later
before used.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200218023625.14324-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DA9062 is a mfd pmic device which supports 5 GPIOs. The GPIOs can
be used as input, output or have a special use-case.
The patch adds the support for the normal input/output use-case.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200108104746.1765-4-m.felsch@pengutronix.de
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andy Shevchenko