The user tool modinfo is used to get information on kernel modules, including a
description where it is available.
This patch adds a brief MODULE_DESCRIPTION to netfilter kernel modules
(descriptions taken from Kconfig file or code comments)
Signed-off-by: Rob Gill <rrobgill@protonmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When using ip_set with counters and comment, traffic causes the kernel
to panic on 32-bit ARM:
Alignment trap: not handling instruction e1b82f9f at [<bf01b0dc>]
Unhandled fault: alignment exception (0x221) at 0xea08133c
PC is at ip_set_match_extensions+0xe0/0x224 [ip_set]
The problem occurs when we try to update the 64-bit counters - the
faulting address above is not 64-bit aligned. The problem occurs
due to the way elements are allocated, for example:
set->dsize = ip_set_elem_len(set, tb, 0, 0);
map = ip_set_alloc(sizeof(*map) + elements * set->dsize);
If the element has a requirement for a member to be 64-bit aligned,
and set->dsize is not a multiple of 8, but is a multiple of four,
then every odd numbered elements will be misaligned - and hitting
an atomic64_add() on that element will cause the kernel to panic.
ip_set_elem_len() must return a size that is rounded to the maximum
alignment of any extension field stored in the element. This change
ensures that is the case.
Fixes: 95ad1f4a93 ("netfilter: ipset: Fix extension alignment")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The error DBG_STATUS_NO_MATCHING_FRAMING_MODE was added to the enum
enum dbg_status however there is a missing corresponding entry for
this in the array s_status_str. This causes an out-of-bounds read when
indexing into the last entry of s_status_str. Fix this by adding in
the missing entry.
Addresses-Coverity: ("Out-of-bounds read").
Fixes: 2d22bc8354 ("qed: FW 8.42.2.0 debug features")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang says:
====================
net: phy: call phy_disable_interrupts() in phy_init_hw()
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
patch1 makes phy_disable_interrupts() non-static so that it could be used
in phy_init_hw() to have a defined init state.
patch2 calls phy_disable_interrupts() in phy_init_hw() to have a
defined init state.
Since v3:
- call phy_disable_interrupts() have interrupts disabled first then
config_init, thank Florian
Since v2:
- Don't export phy_disable_interrupts() but just make it non-static
Since v1:
- EXPORT the correct symbol
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call phy_disable_interrupts() in phy_init_hw() to "have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state." as pointed
out by Heiner.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
Make phy_disable_interrupts() non-static so that it could be used in
phy_init_hw() to have a defined init state.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When writing the serdes configuration register was moved to
mvneta_config_interface() the whole code block was removed from
mvneta_port_power_up() in the assumption that its only purpose was to
write the serdes configuration register. As mentioned by Russell King
its purpose was also to check for valid interface modes early so that
later in the driver we do not have to care for unexpected interface
modes.
Add back the test to let the driver bail out early on unhandled
interface modes.
Fixes: b4748553f5 ("net: ethernet: mvneta: Fix Serdes configuration for SoCs without comphy")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mvneta_config_interface() the RGMII modes are catched by the default
case which is an error return. The RGMII modes are valid modes for the
driver, so instead of returning an error add a break statement to return
successfully.
This avoids this warning for non comphy SoCs which use RGMII, like
SolidRun Clearfog:
WARNING: CPU: 0 PID: 268 at drivers/net/ethernet/marvell/mvneta.c:3512 mvneta_start_dev+0x220/0x23c
Fixes: b4748553f5 ("net: ethernet: mvneta: Fix Serdes configuration for SoCs without comphy")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver for Marvell switches puts all ports in IGMP snooping mode
which results in all IGMP/MLD frames that ingress on the ports to be
forwarded to the CPU only.
The bridge code in the kernel can then interpret these frames and act
upon them, for instance by updating the mdb in the switch to reflect
multicast memberships of stations connected to the ports. However,
the IGMP/MLD frames must then also be forwarded to other ports of the
bridge so external IGMP queriers can track membership reports, and
external multicast clients can receive query reports from foreign IGMP
queriers.
Currently, this is impossible as the EDSA tagger sets offload_fwd_mark
on the skb when it unwraps the tagged frames, and that will make the
switchdev layer prevent the skb from egressing on any other port of
the same switch.
To fix that, look at the To_CPU code in the DSA header and make
forwarding of the frame possible for trapped IGMP packets.
Introduce some #defines for the frame types to make the code a bit more
comprehensive.
This was tested on a Marvell 88E6352 variant.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ovs connection tracking module performs de-fragmentation on incoming
fragmented traffic. Take info account if traffic has been de-fragmented
in execute_check_pkt_len action otherwise we will perform the wrong
nested action considering the original packet size. This issue typically
occurs if ovs-vswitchd adds a rule in the pipeline that requires connection
tracking (e.g. OVN stateful ACLs) before execute_check_pkt_len action.
Moreover take into account GSO fragment size for GSO packet in
execute_check_pkt_len routine
Fixes: 4d5ec89fc8 ("net: openvswitch: Add a new action check_pkt_len")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes all over the place.
This includes a couple of tests that I would normally defer,
but since they have already been helpful in catching some bugs,
don't build for any users at all, and having them
upstream makes life easier for everyone, I think it's
ok even at this late stage.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl7w3hcPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpJ6UH/jVFVzILp3M5eVCewNsS2/j5HvRHxKb4DTwh
eoNTYMSLMy5UnwOdNZ3RjmNHxc8hS04fQsHZpI6mAIPSLWdswjmRwQPN03/fvP9M
nVdy3SxyU2ZzHbX/hRi3eTwhOkOY4RcyvkOjw49LLokIX6/DzsAO5ql3NAZW9vbL
LqZQKzAb7BeltH5RWbPPdF2UCZKia/x9QYHIXh0gJZj5YaAzlvJywNDQcxuiIODb
ZmHZZBaqZ66n99hWnSKfHtqX/fqRDqrdyameIVaSwgewho2AMj9V1FvvVMJWm669
PjQuHDf03TBBDNP9UwJRjdko7qA6aqX5Tef9aGMyBy2LJUD12A8=
=Z/dQ
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Fixes all over the place.
This includes a couple of tests that I would normally defer, but since
they have already been helpful in catching some bugs, don't build for
any users at all, and having them upstream makes life easier for
everyone, I think it's ok even at this late stage"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: Use tools/include/list.h instead of stubs
tools/virtio: Reset index in virtio_test --reset.
tools/virtio: Extract virtqueue initialization in vq_reset
tools/virtio: Use __vring_new_virtqueue in virtio_test.c
tools/virtio: Add --reset
tools/virtio: Add --batch=random option
tools/virtio: Add --batch option
virtio-mem: add memory via add_memory_driver_managed()
virtio-mem: silence a static checker warning
vhost_vdpa: Fix potential underflow in vhost_vdpa_mmap()
vdpa: fix typos in the comments for __vdpa_alloc_device()
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXvNBJgAKCRCRxhvAZXjc
oulGAPoCPfCguA8TPcy4tq4byGPoThyO4XnWR6XcUDOEzhbzzAEA+s5S7iRV8W92
p2gzbI4Kncq4dQNEtUvfPHQZDAEwTA0=
=eZDz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2020-06-24' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull thread fix from Christian Brauner:
"This fixes a regression introduced with 303cc571d1 ("nsproxy: attach
to namespaces via pidfds").
The LTP testsuite reported a regression where users would now see
EBADF returned instead of EINVAL when an fd was passed that referred
to an open file but the file was not a namespace file.
Fix this by continuing to report EINVAL and add a regression test"
* tag 'for-linus-2020-06-24' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
tests: test for setns() EINVAL regression
nsproxy: restore EINVAL for non-namespace file descriptor
When running iperf in a two host configuration the following trace can
occur:
[ 319.728730] NETDEV WATCHDOG: ib0 (hfi1): transmit queue 0 timed out
The issue happens because the current implementation relies on the netif
txq being stopped to control the flushing of the tx list.
There are two resources that the transmit logic can wait on and stop the
txq:
- SDMA descriptors
- Ring space to hold completions
The ring space is tested on the sending side and relieved when the ring is
consumed in the napi tx reaping.
Unfortunately, that reaping can run conncurrently with the workqueue
flushing of the txlist. If the txq is started just before the workitem
executes, the txlist will never be flushed, leading to the txq being
stuck.
Fix by:
- Adding sleep/wakeup wrappers
* Use an atomic to control the call to the netif routines inside the
wrappers
- Use another atomic to record ring space exhaustion
* Only wakeup when the a ring space exhaustion has happened and it
relieved
Add additional wrappers to clarify the ring space resource handling.
Fixes: d99dc602e2 ("IB/hfi1: Add functions to transmit datagram ipoib packets")
Link: https://lore.kernel.org/r/20200623204327.108092.4024.stgit@awfm-01.aw.intel.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The current code mishandles -EBUSY in two ways:
- The flow change doesn't test the return from the flush and runs on to
process the current packet racing with the wakeup processing
- The -EBUSY handling for a single packet inserts the tx into the txlist
after the submit call, racing with the same wakeup processing
Fix the first by dropping the skb and returning NETDEV_TX_OK.
Fix the second by insuring the the list entry within the txreq is inited
when allocated. This enables the sleep routine to detect that the txreq
has used the non-list api and queue the packet to the txlist.
Both flaws can lead to having the flushing thread executing in causing two
threads to manipulate the txlist.
Fixes: d99dc602e2 ("IB/hfi1: Add functions to transmit datagram ipoib packets")
Link: https://lore.kernel.org/r/20200623204321.108092.83898.stgit@awfm-01.aw.intel.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When the try_module_get calls were removed from opening and closing of the
i2c debugfs file, the corresponding module_put calls were missed. This
results in an inaccurate module use count that requires a power cycle to
fix.
Fixes: 09fbca8e62 ("IB/hfi1: No need to use try_module_get for debugfs")
Link: https://lore.kernel.org/r/20200623203230.106975.76240.stgit@awfm-01.aw.intel.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The USB-audio mixer code holds a linked list of usb_mixer_elem_list,
and several operations are performed for each mixer element. A few of
them (snd_usb_mixer_notify_id() and snd_usb_mixer_interrupt_v2())
assume each mixer element being a usb_mixer_elem_info object that is a
subclass of usb_mixer_elem_list, cast via container_of() and access it
members. This may result in an out-of-bound access when a
non-standard list element has been added, as spotted by syzkaller
recently.
This patch adds a new field, is_std_info, in usb_mixer_elem_list to
indicate that the element is the usb_mixer_elem_info type or not, and
skip the access to such an element if needed.
Reported-by: syzbot+fb14314433463ad51625@syzkaller.appspotmail.com
Reported-by: syzbot+2405ca3401e943c538b5@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200624122340.9615-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Russell King says:
====================
Two phylink pause fixes
While testing, I discovered two issues with ethtool -A with phylink.
First, if there is a PHY bound to the network device, we hit a
deadlock when phylib tries to notify us of the link changing as a
result of triggering a renegotiation.
Second, when we are manually forcing the pause settings, and there
is no renegotiation triggered, we do not update the MAC via the new
mac_link_up approach.
These two patches solve both problems, and will need to be backported
to v5.7; they do not apply cleanly there due to the introduction of
PCS in the v5.8 merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been relying on link events and mac_config() when the manual
pause modes are changed. With recent developments, such as moving
the programming of link state to mac_link_up(), this no longer works.
To ensure that we update the MAC, we must generate a link-down followed
by a link-up event; we can do that by setting mac_link_dropped and
triggering a resolve.
Fixes: 91a208f218 ("net: phylink: propagate resolved link config via mac_link_up()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a phylink's ethtool set_pauseparam support deadlock caused by phylib
interacting with phylink: we must not hold the state lock while calling
phylib functions that may call into phylink_phy_change().
Fixes: f904f15ea9 ("net: phylink: allow ethtool -A to change flow control advertisement")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the sock TX queue in sk_set_socket() might cause unexpected
out-of-order transmit when called from sock_orphan(), as outstanding
packets can pick a different TX queue and bypass the ones already queued.
This is undesired in general. More specifically, it breaks the in-order
scheduling property guarantee for device-offloaded TLS sockets.
Remove the call to sk_tx_queue_clear() in sk_set_socket(), and add it
explicitly only where needed.
Fixes: e022f0b4a0 ("net: Introduce sk_tx_queue_mapping")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A last minute change put the TDR cable test parameters into a nest.
The validation is not sufficient, resulting in an oops if the nest is
missing. Set default values first, then update them if the nest is
provided.
Fixes: f2bc8ad31a ("net: ethtool: Allow PHY cable test TDR data to configured")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Bug fixes.
The first patch stores the firmware version code which is needed by the
next 2 patches to determine some worarounds based on the firmware version.
The workarounds are to disable legacy TX push mode and to clear the
hardware statistics during ifdown. The last patch checks that it is
a PF before reading the VPD.
Please also queue these for -stable. Thanks.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual functions does not have VPD information. This patch modifies
calling bnxt_read_vpd_info() only for PFs and avoids an unnecessary
error log.
Fixes: a0d0fd70fe ("bnxt_en: Read partno and serialno of the board from VPD")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On older firmware, the hardware statistics are not cleared when the
driver frees the hardware stats contexts during ifdown. The driver
expects these stats to be cleared and saves a copy before freeing
the stats contexts. During the next ifup, the driver will likely
allocate the same hardware stats contexts and this will cause a big
increase in the counters as the old counters are added back to the
saved counters.
We fix it by making an additional firmware call to clear the counters
before freeing the hw stats contexts when the firmware is the older
20.x firmware.
Fixes: b8875ca356 ("bnxt_en: Save ring statistics before reset.")
Reported-by: Jakub Kicinski <kicinski@fb.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Jakub Kicinski <kicinski@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older firmware may not support legacy TX push properly and may not
be disabling it. So we check certain firmware versions that may
have this problem and disable legacy TX push unconditionally.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only store the firmware version as a string for ethtool
and devlink info. Store it also as a version code. The next 2
patches will need to check the firmware major version to determine
some workarounds.
We also use the 16-bit firmware version fields if the firmware is newer
and provides the 16-bit fields.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix boottime kprobe events to report and abort after each failure when
adding probes.
As an example, when we try to set multiprobe kprobe events in
bootconfig like this:
ftrace.event.kprobes.vfsevents {
probes = "vfs_read $arg1 $arg2,,
!error! not reported;?", // leads to error
"vfs_write $arg1 $arg2"
}
This will not work as expected. After
commit da0f1f4167 ("tracing/boottime: Fix kprobe event API usage"),
the function trace_boot_add_kprobe_event will not produce any error
message when adding a probe fails at kprobe_event_gen_cmd_start.
Furthermore, we continue to add probes when kprobe_event_gen_cmd_end fails
(and kprobe_event_gen_cmd_start did not fail). In this case the function
even returns successfully when the last call to kprobe_event_gen_cmd_end
is successful.
The behaviour of reporting and aborting after failures is not
consistent.
The function trace_boot_add_kprobe_event now reports each failure and
stops adding probes immediately.
Link: https://lkml.kernel.org/r/20200618163301.25854-1-sascha.ortmann@stud.uni-hannover.de
Cc: stable@vger.kernel.org
Cc: linux-kernel@i4.cs.fau.de
Co-developed-by: Maximilian Werner <maximilian.werner96@gmail.com>
Fixes: da0f1f4167 ("tracing/boottime: Fix kprobe event API usage")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Maximilian Werner <maximilian.werner96@gmail.com>
Signed-off-by: Sascha Ortmann <sascha.ortmann@stud.uni-hannover.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix the event trigger to accept redundant spaces in
the trigger input.
For example, these return -EINVAL
echo " traceon" > events/ftrace/print/trigger
echo "traceon if common_pid == 0" > events/ftrace/print/trigger
echo "disable_event:kmem:kmalloc " > events/ftrace/print/trigger
But these are hard to find what is wrong.
To fix this issue, use skip_spaces() to remove spaces
in front of actual tokens, and set NULL if there is no
token.
Link: http://lkml.kernel.org/r/159262476352.185015.5261566783045364186.stgit@devnote2
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 85f2b08268 ("tracing: Add basic event trigger framework")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Since commit 726721a518 ("tracing: Move synthetic events to
a separate file") decoupled synthetic event from histogram,
boot-time tracing also has to check CONFIG_SYNTH_EVENT instead
of CONFIG_HIST_TRIGGERS.
Link: http://lkml.kernel.org/r/159262475441.185015.5300725180746017555.stgit@devnote2
Fixes: 726721a518 ("tracing: Move synthetic events to a separate file")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Hongyu reported "id != index" in z_erofs_onlinepage_fixup() with
specific aarch64 environment easily, which wasn't shown before.
After digging into that, I found that high 32 bits of page->private
was set to 0xaaaaaaaa rather than 0 (due to z_erofs_onlinepage_init
behavior with specific compiler options). Actually we only use low
32 bits to keep the page information since page->private is only 4
bytes on most 32-bit platforms. However z_erofs_onlinepage_fixup()
uses the upper 32 bits by mistake.
Let's fix it now.
Reported-and-tested-by: Hongyu Jin <hongyu.jin@unisoc.com>
Fixes: 3883a79abd ("staging: erofs: introduce VLE decompression support")
Cc: <stable@vger.kernel.org> # 4.19+
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Link: https://lore.kernel.org/r/20200618234349.22553-1-hsiangkao@aol.com
Signed-off-by: Gao Xiang <hsiangkao@redhat.com>
When producing the bpf-helpers.7 man page from the documentation from
the BPF user space header file, rst2man complains:
<stdin>:2636: (ERROR/3) Unexpected indentation.
<stdin>:2640: (WARNING/2) Block quote ends without a blank line; unexpected unindent.
Let's fix formatting for the relevant chunk (item list in
bpf_ringbuf_query()'s description), and for a couple other functions.
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200623153935.6215-1-quentin@isovalent.com
This is a fix for a regression in commit 2c78ee898d ("bpf: Implement CAP_BPF").
Before the above commit it was possible to load network bpf programs
with just the CAP_SYS_ADMIN privilege.
The Android bpfloader happens to run in such a configuration (it has
SYS_ADMIN but not NET_ADMIN) and creates maps and loads bpf programs
for later use by Android's netd (which has NET_ADMIN but not SYS_ADMIN).
Fixes: 2c78ee898d ("bpf: Implement CAP_BPF")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/bpf/20200620212616.93894-1-zenczykowski@gmail.com
Currently, if a bpf program has more than one subprograms, each program will be
jitted separately. For programs with bpf-to-bpf calls the
prog->aux->num_exentries is not setup properly. For example, with
bpf_iter_netlink.c modified to force one function to be not inlined and with
CONFIG_BPF_JIT_ALWAYS_ON the following error is seen:
$ ./test_progs -n 3/3
...
libbpf: failed to load program 'iter/netlink'
libbpf: failed to load object 'bpf_iter_netlink'
libbpf: failed to load BPF skeleton 'bpf_iter_netlink': -4007
test_netlink:FAIL:bpf_iter_netlink__open_and_load skeleton open_and_load failed
#3/3 netlink:FAIL
The dmesg shows the following errors:
ex gen bug
which is triggered by the following code in arch/x86/net/bpf_jit_comp.c:
if (excnt >= bpf_prog->aux->num_exentries) {
pr_err("ex gen bug\n");
return -EFAULT;
}
This patch fixes the issue by computing proper num_exentries for each
subprogram before calling JIT.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
bpf_object__find_program_by_title(), used by CO-RE relocation code, doesn't
return .text "BPF program", if it is a function storage for sub-programs.
Because of that, any CO-RE relocation in helper non-inlined functions will
fail. Fix this by searching for .text-corresponding BPF program manually.
Adjust one of bpf_iter selftest to exhibit this pattern.
Fixes: ddc7c30426 ("libbpf: implement BPF CO-RE offset relocation algorithm")
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200619230423.691274-1-andriin@fb.com
Rahul Lakkireddy says:
====================
cxgb4/cxgb4vf: fix warnings reported by sparse
This series of patches fix various warnings reported by the sparse
tool.
Patches 1 and 2 fix lock context imbalance warnings.
Patch 3 fixes cast to restricted __be64 warning when fetching
timestamp in PTP path.
Patch 4 fixes several cast to restricted __be32 warnings in TC-U32
offload parser.
Patch 5 fixes several cast from restricted __be16 warnings in parsing
L4 ports for filters.
Patch 6 fixes several restricted __be32 degrades to integer warnings
when comparing IP address masks for exact-match filters.
Patch 7 fixes cast to restricted __be64 warning when fetching SGE
queue contexts in device dump collection.
Patch 8 fixes cast from restricted __sum16 warning when saving IPv4
partial checksum.
Patch 9 fixes issue with string array scope in DCB path.
Patch 10 fixes a set but unused variable warning when DCB is disabled.
Patch 11 fixes several kernel-doc comment warnings in cxgb4 driver.
Patch 12 fixes several kernel-doc comment warnings in cxgb4vf driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update several kernel-doc line comments to fix warnings reported by
make W=1.
Fixes following class of warnings reported by make W=1 in several
places:
cxgb4vf_main.c:275: warning: Function parameter or member 'persistent'
not described in 'cxgb4vf_change_mac'
cxgb4vf_main.c:275: warning: Excess function parameter 'persist'
description in 'cxgb4vf_change_mac'
Fixes: 16f8bd4be7 ("cxgb4vf: Add core T4 PCI-E SR-IOV Virtual Function hardware definitions and device communication code")
Fixes: c6e0d91464 ("cxgb4vf: Add T4 Virtual Function Scatter-Gather Engine DMA code")
Fixes: e0a8b34a9c ("cxgb4vf: Add and initialize some sge params for VF driver")
Fixes: c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Fixes: 0e23daeb64 ("drivers/net: chelsio/cxgb*: Convert timers to use timer_setup()")
Fixes: 3f8cfd0d95 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update several kernel-doc line comments to fix warnings reported by
make W=1.
Fixes following class of warnings reported by make W=1 in several
places:
l2t.c:616: warning: Cannot understand * @dev: net_device pointer
t4_hw.c:3175: warning: Function parameter or member 'adap' not
described in 't4_get_exprom_version'
t4_hw.c:3175: warning: Excess function parameter 'adapter' description
in 't4_get_exprom_version'
Fixes: 56d36be4dd ("cxgb4: Add HW and FW support code")
Fixes: fd3a47900b ("cxgb4: Add packet queues and packet DMA code")
Fixes: 26f7cbc0a5 ("cxgb4: Don't attempt to upgrade T4 firmware when cxgb4 will end up as a slave")
Fixes: 793dad94e7 ("RDMA/cxgb4: Fix bug for active and passive LE hash collision path")
Fixes: ba3f8cd55f ("cxgb4: Add support in cxgb4 to get expansion rom version via ethtool")
Fixes: f7502659ce ("cxgb4: Add API to alloc l2t entry; also update existing ones")
Fixes: ddc7740d9a ("cxgb4: Decode link down reason code obtained from firmware")
Fixes: 193c4c2845 ("cxgb4: Update T6 Buffer Group and Channel Mappings")
Fixes: 8f46d46715 ("cxgb4: Use Firmware params to get buffer-group map")
Fixes: a456950445 ("cxgb4: time stamping interface for PTP")
Fixes: 9c33e4208b ("cxgb4: Add PTP Hardware Clock (PHC) support")
Fixes: c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Fixes: 5ccf9d0496 ("cxgb4: update API for TP indirect register access")
Fixes: 3bdb376e69 ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support")
Fixes: 736c3b9447 ("cxgb4: collect egress and ingress SGE queue contexts")
Fixes: f56ec6766d ("cxgb4: Add support for ethtool i2c dump")
Fixes: 9d5fd927d2 ("cxgb4/cxgb4vf: add support for ndo_set_vf_vlan")
Fixes: 98f3697f8d ("cxgb4: add tc flower match support for tunnel VNI")
Fixes: 02d805dc5f ("cxgb4: use new fw interface to get the VIN and smt index")
Fixes: 3f8cfd0d95 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the set but unused variable when DCB is disabled. Instead,
do the calculation directly inline.
Fixes following warning in make W=1:
cxgb4_main.c: In function 'cfg_queues':
cxgb4_main.c:5380:29: warning: variable 'n1g' set but not used
[-Wunused-but-set-variable]
u32 i, n10g = 0, qidx = 0, n1g = 0;
^
Fixes: 116ca924ae ("cxgb4: fix checks for max queues to allocate")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DCB version string array extern to header file.
Fixes following sparse warning:
cxgb4_dcb.c:13:12: warning: symbol 'dcb_ver_array' was not declared.
Should it be static?
Fixes: ebddd97afb ("cxgb4: add support to display DCB info")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checksum field in IPv4 header is in __sum16 and ip_fast_csum()
also returns __sum16. So, no need to cast it to u16.
Fixes following sparse warning:
sge.c:1539:47: warning: cast from restricted __sum16
sge.c:1539:44: warning: incorrect type in assignment (different base types)
sge.c:1539:44: expected restricted __sum16 [usertype] check
sge.c:1539:44: got unsigned short [usertype]
Fixes: d0a1299c6b ("cxgb4: add support for vxlan segmentation offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data in destination buffer is expected to be be parsed in big
endian. So, use the right context.
Fixes following sparse warning:
cudbg_lib.c:2041:44: warning: incorrect type in assignment (different
base types)
cudbg_lib.c:2041:44: expected unsigned long long [usertype]
cudbg_lib.c:2041:44: got restricted __be64 [usertype]
Fixes: 736c3b9447 ("cxgb4: collect egress and ingress SGE queue contexts")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct type to check for all-mask exact match IP addresses.
Fixes following sparse warnings due to big endian value checks
against 0xffffffff in is_addr_all_mask():
cxgb4_filter.c:977:25: warning: restricted __be32 degrades to integer
cxgb4_filter.c:983:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:984:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:985:37: warning: restricted __be32 degrades to integer
cxgb4_filter.c:986:37: warning: restricted __be32 degrades to integer
Fixes: 3eb8b62d5a ("cxgb4: add support to create hash-filters via tc-flower offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The source and destination L4 ports in filter offload need to be
in CPU endian. They will finally be converted to Big Endian after
all operations are done and before giving them to hardware. The
L4 ports for NAT are expected to be passed as a byte stream TCB.
So, treat them as such.
Fixes following sparse warnings in several places:
cxgb4_tc_flower.c:159:33: warning: cast from restricted __be16
cxgb4_tc_flower.c:159:33: warning: incorrect type in argument 1 (different
base types)
cxgb4_tc_flower.c:159:33: expected unsigned short [usertype] val
cxgb4_tc_flower.c:159:33: got restricted __be16 [usertype] dst
Fixes: dca4faeb81 ("cxgb4: Add LE hash collision bug fix path in LLD driver")
Fixes: 62488e4b53 ("cxgb4: add basic tc flower offload support")
Fixes: 557ccbf9df ("cxgb4: add tc flower support for L3/L4 rewrite")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC-U32 passes all keys values and masks in __be32 format. The parser
already expects this and hence pass the value and masks in __be32
natively to the parser.
Fixes following sparse warnings in several places:
cxgb4_tc_u32.c:57:21: warning: incorrect type in assignment (different base
types)
cxgb4_tc_u32.c:57:21: expected unsigned int [usertype] val
cxgb4_tc_u32.c:57:21: got restricted __be32 [usertype] val
cxgb4_tc_u32_parse.h:48:24: warning: cast to restricted __be32
Fixes: 2e8aad7bf2 ("cxgb4: add parser to translate u32 filters to internal spec")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use get_unaligned_be64() to fetch the timestamp needed for ns_to_ktime()
conversion.
Fixes following sparse warning:
sge.c:3282:43: warning: cast to restricted __be64
Fixes: a456950445 ("cxgb4: time stamping interface for PTP")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for whether PTP is enabled or not at the caller and perform
locking/unlocking at the caller.
Fixes following sparse warning:
sge.c:1641:26: warning: context imbalance in 'cxgb4_eth_xmit' -
different lock contexts for basic block
Fixes: a456950445 ("cxgb4: time stamping interface for PTP")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move code handling L2T ARP failures to the only caller.
Fixes following sparse warning:
skbuff.h:2091:29: warning: context imbalance in
'handle_failed_resolution' - unexpected unlock
Fixes: 749cb5fe48 ("cxgb4: Replace arpq_head/arpq_tail with SKB double link-list code")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Lobakin says:
====================
net: qed/qede: various stability fixes
This set addresses several near-critical issues that were observed
and reproduced on different test and production configurations.
v2:
- don't split the "Fixes:" tag across several lines in patch 9;
- no functional changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'abs_ppfid' in qed_dev.c:qed_llh_add_mac_filter() always gets
printed, but is initialized only under 'ref_cnt == 1' condition. This
results in:
In file included from ./include/linux/kernel.h:15:0,
from ./include/asm-generic/bug.h:19,
from ./arch/x86/include/asm/bug.h:86,
from ./include/linux/bug.h:5,
from ./include/linux/io.h:11,
from drivers/net/ethernet/qlogic/qed/qed_dev.c:35:
drivers/net/ethernet/qlogic/qed/qed_dev.c: In function 'qed_llh_add_mac_filter':
./include/linux/printk.h:358:2: warning: 'abs_ppfid' may be used uninitialized
in this function [-Wmaybe-uninitialized]
printk(KERN_NOTICE pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~
drivers/net/ethernet/qlogic/qed/qed_dev.c:983:17: note: 'abs_ppfid' was declared
here
u8 filter_idx, abs_ppfid;
^~~~~~~~~
...under W=1+.
Fix this by initializing it with zero.
Fixes: 79284adeb9 ("qed: Add llh ppfid interface and 100g support for offload protocols")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gill