Pass wake up source mask and wakeup source polarity to deepsleep and
hibernate.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Otherwise, the compiler may optimize assemble code into 8bit access instruction
when target register is 8 bit width.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Add add deepsleep for bf60x.
1. Call DMC init functions to enter and exit DDR self refresh mode.
2. Wait till CGU PLL is locked after wake up and exit DDR self refresh mode.
3. Make asessembly function enter_deepsleep comply with C funtion ABI in
order to call other C functions.
4. Switch kernel stack by register EX_SCRATCH_REG.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Extend chip select number supported by spi master as well
because we can accept SPISEL1-SPISEL7 and all GPIO.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Pull arch/tile updates from Chris Metcalf:
"These changes provide support for PCIe root complex and USB host mode
for tilegx's on-chip I/Os.
In addition, this pull provides the required underpinning for the
on-chip networking support that was pulled into 3.5. The changes have
all been through LKML (with several rounds for PCIe RC) and on
linux-next."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: updates to pci root complex from community feedback
bounce: allow use of bounce pool via config option
usb: add host support for the tilegx architecture
arch/tile: provide kernel support for the tilegx USB shim
tile pci: enable IOMMU to support DMA for legacy devices
arch/tile: enable ZONE_DMA for tilegx
tilegx pci: support I/O to arbitrarily-cached pages
tile: remove unused header
arch/tile: tilegx PCI root complex support
arch/tile: provide kernel support for the tilegx TRIO shim
arch/tile: break out the "csum a long" function to <asm/checksum.h>
arch/tile: provide kernel support for the tilegx mPIPE shim
arch/tile: common DMA code for the GXIO IORPC subsystem
arch/tile: support MMIO-based readb/writeb etc.
arch/tile: introduce GXIO IORPC framework for tilegx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K7ad
-----END PGP SIGNATURE-----
Merge tag 'please-pull-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull misc Itanium fixes from Tony Luck.
* tag 'please-pull-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
debug: Do not permit CONFIG_DEBUG_STACK_USAGE=y on IA64 or PARISC
[IA64] Port OOM changes to ia64_do_page_fault
- Migration off of old-style dynamic IRQ API.
- irqdomain and generic irq chip propagation.
- div4/6 clock consolidation, another step towards co-existing
with the common struct clk infrastructure.
- Extensive PFC rework
- Decoupling GPIO from pin state.
- Initial pinctrl support to facilitate incremental migration
off of legacy pinmux.
- gpiolib support made optional, and made pinctrl-backed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlAM6oMACgkQGkmNcg7/o7i63gCgru+ZynCrxdH5zq4er46MFoAF
DVsAoLq3P+UCPDZc7pvksr6kgFiYGHG3
=Dd+j
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt:
- Migration off of old-style dynamic IRQ API.
- irqdomain and generic irq chip propagation.
- div4/6 clock consolidation, another step towards co-existing with the
common struct clk infrastructure.
- Extensive PFC rework
- Decoupling GPIO from pin state.
- Initial pinctrl support to facilitate incremental migration off of
legacy pinmux.
- gpiolib support made optional, and made pinctrl-backed.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (38 commits)
sh: pfc: pin config get/set support.
sh: pfc: Prefer DRV_NAME over KBUILD_MODNAME.
sh: pfc: pinctrl legacy group support.
sh: pfc: Ignore pinmux GPIOs with invalid enum IDs.
sh: pfc: Export pinctrl binding init symbol.
sh: pfc: Error out on pinctrl init resolution failure.
sh: pfc: Make pr_fmt consistent across pfc drivers.
sh: pfc: pinctrl legacy function support.
sh: pfc: Rudimentary pinctrl-backed GPIO support.
sh: pfc: Dumb GPIO stringification.
sh: pfc: Shuffle PFC support core.
sh: pfc: Verify pin type encoding size at build time.
sh: pfc: Kill off unused pinmux bias flags.
sh: pfc: Make gpio chip support optional where possible.
sh: pfc: Split out gpio chip support.
sh64: Fix up section mismatch warnings.
sh64: Attempt to make reserved insn trap handler resemble C.
sh: Consolidate die definitions for trap handlers.
sh64: Kill off old exception debugging helpers.
sh64: Use generic unaligned access control/counters.
...
Pull powerpc updates from Benjamin Herrenschmidt:
"Notable highlights:
- iommu improvements from Anton removing the per-iommu global lock in
favor of dividing the DMA space into pools, each with its own lock,
and hashed on the CPU number. Along with making the locking more
fine grained, this gives significant improvements in multiqueue
networking scalability.
- Still from Anton, we know provide a vdso based variant of getcpu
which makes sched_getcpu with the appropriate glibc patch something
like 18 times faster.
- More anton goodness (he's been busy !) in other areas such as a
faster __clear_user and copy_page on P7, various perf fixes to
improve sampling quality, etc...
- One more step toward removing legacy i2c interfaces by using new
device-tree based probing of platform devices for the AOA audio
drivers
- A nice series of patches from Michael Neuling that helps avoiding
confusion between register numbers and litterals in assembly code,
trying to enforce the use of "%rN" register names in gas rather
than plain numbers.
- A pile of FSL updates
- The usual bunch of small fixes, cleanups etc...
You may spot a change to drivers/char/mem. The patch got no comment
or ack from outside, it's a trivial patch to allow the architecture to
skip creating /dev/port, which we use to disable it on ppc64 that
don't have a legacy brige. On those, IO ports 0...64K are not mapped
in kernel space at all, so accesses to /dev/port cause oopses (and
yes, distros -still- ship userspace that bangs hard coded ports such
as kbdrate)."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/mpic: Create a revmap with enough entries for IPIs and timers
Remove stale .rej file
powerpc/iommu: Fix iommu pool initialization
powerpc/eeh: Check handle_eeh_events() return value
powerpc/85xx: Add phy nodes in SGMII mode for MPC8536/44/72DS & P2020DS
powerpc/e500: add paravirt QEMU platform
powerpc/mpc85xx_ds: convert to unified PCI init
powerpc/fsl-pci: get PCI init out of board files
powerpc/85xx: Update corenet64_smp_defconfig
powerpc/85xx: Update corenet32_smp_defconfig
powerpc/85xx: Rename P1021RDB-PC device trees to be consistent
powerpc/watchdog: move booke watchdog param related code to setup-common.c
sound/aoa: Adapt to new i2c probing scheme
i2c/powermac: Improve detection of devices from device-tree
powerpc: Disable /dev/port interface on systems without an ISA bridge
of: Improve prom_update_property() function
powerpc: Add "memory" attribute for mfmsr()
powerpc/ftrace: Fix assembly trampoline register usage
powerpc/hw_breakpoints: Fix incorrect pointer access
powerpc: Put the gpr save/restore functions in their own section
...
Clock support is moving to the clk subsystem. These tegra, omap and imx
changes are for code that is still platform specific and not (yet)
part of that subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Cvpa
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clk changes from Arnd Bergmann:
"Clock support is moving to the clk subsystem. These tegra, omap and
imx changes are for code that is still platform specific and not (yet)
part of that subsystem."
Fix up conflicts in arch/arm/mach-{imx/clk-imx51-imx53.c,omap2/Makefile}
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: imx: clk-imx31: Fix clock id for rnga driver
ARM: imx: add missing item to the list of clock event modes
ARM: i.MX5x CSPI: Fixed clock name for CSPI
ARM: i.MX5x clocks: Fix GPT clocks
ARM: i.MX5x clocks: Fix parent for PWM clocks
ARM: i.MX5x clocks: Add EPIT support
ARM: mx27: Reenable silicon version print
ARM: clk-imx27: Fix rtc clock id
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
...
These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap smartreflex
driver to live in the power subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tgT5
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc power management changes from Arnd Bergmann:
"These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap
smartreflex driver to live in the power subsystem."
Fix up conflicts in arch/arm/mach-{imx/mach-imx6q.c,omap2/prm2xxx_3xxx.h}
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP2+: do not allow SmartReflex to be built as a module
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
W1: OMAP HDQ1W: use runtime PM
ARM: OMAP2+: HDQ1W: use omap_device
W1: OMAP HDQ1W: use 32-bit register accesses
W1: OMAP HDQ1W: allow driver to be built on all OMAP2+
...
We are converting platforms to use the pinctrl framework over time,
rather than using platform specific code for the same effect. This
adds the respective driver for the prima2 platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YodD
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc pincontrol drivers update from Arnd Bergmann:
"We are converting platforms to use the pinctrl framework over time,
rather than using platform specific code for the same effect. This
adds the respective driver for the prima2 platform."
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: prima2: enable gpiolib unconditionally
PINCTRL: SiRF: add GPIO and GPIO irq support in CSR SiRFprimaII
The I.MX platform is getting converted to use sparse IRQs. We are doing
this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Y2Sm
-----END PGP SIGNATURE-----
Merge tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc sparse IRQ conversion from Arnd Bergmann:
"The I.MX platform is getting converted to use sparse IRQs. We are
doing this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea."
* tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: select USE_OF
ARM: imx: Fix build error due to missing irqs.h include
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
These changes are all for individual board files. In the long run, those
files will largely go away, and the amount of changes appears to be
continuously decreasing, which is a good sign. This time around, changes
are focused on tegra, omap and samsung.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nKn1
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific updates from Arnd Bergmann:
"These changes are all for individual board files. In the long run,
those files will largely go away, and the amount of changes appears to
be continuously decreasing, which is a good sign. This time around,
changes are focused on tegra, omap and samsung."
Fix conflicts in arch/arm/mach-{omap2/common-board-devices.c,tegra/Makefile.boot}
as per the 'for-linus' branch.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: EXYNOS: Add leds status1 and status2 on Origen board
ARM: S3C64XX: Mark most Cragganmore initdata devinitdata
ARM: EXYNOS: Add missing .reserve field to SMDKC210
ARM: EXYNOS: Add DRM device to SMDK4X12 board
ARM: S3C64XX: Clean up after SPI driver platform data updates
ARM: SAMSUNG: no need to set the value for clk_xusbxti when it is 24Mhz
ARM: EXYNOS: Add framebuffer support for SMDK4X12
ARM: EXYNOS: Add HSOTG support to SMDK4X12
ARM: S5PV210: Add audio platform device in Goni board
ARM: S5PV210: Add audio platform device in Aquila board
ARM: EXYNOS: Add audio platform device in SMDKV310 board
ARM: S3C64XX: Don't specify an irq_base for WM1192-EV1 board
ARM: OMAP3: Fix omap3evm randconfig error introduced by VBUS support
ARM: OMAP: board-omap4panda: MUX configuration for sys_nirq2
ARM: OMAP: board-4430sdp: MUX configuration for sys_nirq2
ARM: OMAP3530evm: set pendown_state and debounce time for ads7846
ARM: omap3evm: enable VBUS switch for EHCI tranceiver
ARM: OMAP3EVM: Adding USB internal LDOs board file
ARM: OMAP3EVM: Add NAND flash definition
ARM: OMAP3: cm-t35: add tvp5150 decoder support
...
These are changes to the default configuration files, to account for
kernel changes and new hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZshZ
-----END PGP SIGNATURE-----
Merge tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc defconfig updates from Arnd Bergmann:
"These are changes to the default configuration files, to account for
kernel changes and new hardware."
* tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos_defconfig: enable more platforms in defconfig
ARM: imx_v4_v5_defconfig: update features
ARM: imx_v6_v7_defconfig: update features
ARM: mxs: defconfig: Enable CONFIG_COMMON_CLK_DEBUG
ARM: mxs_defconfig: Enable RTC driver
ARM: LPC32xx: Defconfig update
ARM: mxs_defconfig: Let AUART driver be built by default
ARM: mxs: Enable MACH_APX4DEVKIT
ARM: mxs: Let GPMI driver be built by default
ARM: tegra: defconfig updates
This adds support for three new SoC types:
* The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
* socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are
expected to get added in the FPGA.
* The OMAP subarchitecture gains support for the latest generation,
the OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=MwdJ
-----END PGP SIGNATURE-----
Merge tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for three new arm SoC types from Arnd Bergmann:
- The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
- socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are expected
to get added in the FPGA.
- The OMAP subarchitecture gains support for the latest generation, the
OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
* tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: socfpga: initial support for Altera's SOCFPGA platform
arm: mvebu: generate DTBs for supported SoCs
ARM: mvebu: MPIC: read number of interrupts from control register
arm: mach-mvebu: add entry to MAINTAINERS
arm: mach-mvebu: add compilation/configuration change
arm: mach-mvebu: add defconfig
arm: mach-mvebu: add documentation for new device tree bindings
arm: mach-mvebu: add support for Armada 370 and Armada XP with DT
arm: mach-mvebu: add source files
arm: mach-mvebu: add header
clocksource: time-armada-370-xp: Marvell Armada 370/XP SoC timer driver
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
...
Conflicts:
Documentation/devicetree/bindings/arm/omap/omap.txt
arch/arm/mach-omap2/Makefile
drivers/clocksource/Kconfig
drivers/clocksource/Makefile
These omap cleanups have dependencies on earlier omap branches that in
turn depend on other cleanups, so they could not go into the same
branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kMNb
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups, part 2, from Arnd Bergmann:
"These omap cleanups have dependencies on earlier omap branches that in
turn depend on other cleanups, so they could not go into the same
branch."
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: sdrc: Fix the build break for OMAP4 only builds
ARM: OMAP2+: dmtimer: cleanup fclk usage
ARM: OMAP2+: Fix mismerge for omap_hwmod_get_main_clk() API
ARM: OMAP2+: Remove unnecessary ifdef around __omap2_set_globals
ARM: OMAP2+: am33xx: Change cpu_is_am33xx to soc_is_am33xx
ARM: OMAP2+: am33xx: Make am33xx as a separate class
ARM: OMAP2+: Move omap3 dpll ops to dpll3xxx.c
ARM: OMAP2+: All OMAP2PLUS uses omap-device.o target so add one entry
ARM: OMAP: dmtimer: use devm_ API and do some cleanup in probe()
ARM: OMAP2+: hwmod code: add support to set dmadisable in hwmod framework
ARM: OMAP2+: PRM/CM: Move the stubbed prm and cm functions to prcm.c file and make them __weak
ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API
ARM: OMAP3+: dpll: optimize noncore dpll locking logic
ARM: OMAP3: control: add definition for CONTROL_CAMERA_PHY_CTRL
ARM: OMAP2+: powerdomain code: Fix Wake-up power domain power status
ARM: OMAP4: clockdomain/CM code: Update supported transition modes
ARM: OMAP3/4: omap_hwmod: Add rstst_offs field to struct omap_hwmod_omap4_prcm
ARM: OMAP2+: hwmod: Add new sysc_type3 into omap_hwmod required for am33xx
This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2bZ2
-----END PGP SIGNATURE-----
Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc timer updates from Arnd Bergmann:
"This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver."
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
This branch contains two kinds of updates: Some platforms in the process
of getting converted to device tree based booting, and the platform
specific patches necessary for that are included here. Other platforms
are already converted, so we just need to update the actual device
tree source files and the binding documents to add support for new board
and new drivers.
In the future we will probably separate those into two branches, and
in the long run, the plan is to move the device tree source files out
of the kernel repository, but that has to wait until we have completed
a much larger portion of the binding documents.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUAUA2dbmCrR//JCVInAQJl0hAA3U3AnfBBXbKEJhUi47z6QU2kRPVfyjAj
ct+FsZMWFihEHC5/YkB/bQ/i7Hf/AKBZRG6eAUfsyevuhQ0Li+wsRM4eU3FaF6kw
HNqqB6GQWM+2rR8//Y6AAZymTLfe5nbuWFhRXiIggIlQne5jJ1kSidmSzG+OJEuN
sAKXX7Ud5goVsby9Uwp4Gc0fpDsjFmIarhHfMDizFozNZIFzZIhKKdl1VOf+Kv+o
PFRfCGB2KQrrDy0oB62y3iNUiK84LA0xWX4KkI9rD4OHWeiDQpbUITchf//Wa20X
vgZdI8T16sxbmAHi1zerIl8y/CLgLyerp1L3KSMGTwirC+92vZg+jOGYGgNqu973
NOl0IBQFpbAlNzmf52naNgcQ2OxxFQ3ogrlpvE2bItLL7J3vpmn1JwWMTtSrcs3Z
xgbovAq2ivNOiKpzXexvMsWDCU3PxzXaP+2hEUhglJcdXkx5Iwiwi6un2FuF2qWT
l5rSAWkg2kT/OkgYHLBI5JW7e7ugWhUAuCsrIH9eW7xstm4hIlN950vefs2FrZkP
FeE7pn6s6mr98+j9isJKusETXIoEXDLX61vxA8PQP7GYN+/O/g2qB0qztBwarMBL
wAdHCjavOYNwPkxYaGLjv9qKt3X575O/6aFa/NoKGhIECanjLl02Tqg02BdHecST
8HENXCvwQns=
=K3WL
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree description updates from Arnd Bergmann:
"This branch contains two kinds of updates: Some platforms in the
process of getting converted to device tree based booting, and the
platform specific patches necessary for that are included here.
Other platforms are already converted, so we just need to update the
actual device tree source files and the binding documents to add
support for new board and new drivers.
In the future we will probably separate those into two branches, and
in the long run, the plan is to move the device tree source files out
of the kernel repository, but that has to wait until we have completed
a much larger portion of the binding documents."
Fix up trivial conflicts in arch/arm/mach-imx/clk-imx6q.c due to newly
added clkdev registers next to a few removed unnecessary ones.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: LPC32xx: Add PWM to base dts file
ARM: EXYNOS: mark the DMA channel binding for SPI as preliminary
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
ARM: EXYNOS: Add spi clock support for EXYNOS5
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
ARM: ux500: Remove PMU platform registration when booting with DT
ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
ARM: ux500: Ensure vendor specific properties have the vendor's identifier
pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
...
Some platforms are not yet converted to use the dmaengine framework,
including some of the samsung SoCs. In the meantime, we treat this
as platform code and merge the patches through the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUAUA2da2CrR//JCVInAQIwehAA3GPguLehDaYaySrPWJYWlE1IKBrQJA+u
MIsUBo8wEzd6Hz5XiKG8s6HvplZn6bhEjVESFTuIwaDWaBSAw1npLYZ4gHE3wVvZ
msHLkeqwwCbBnnUkRUDoF/S2nONjgItgsndpNu9ejXaUNZ3Cw2lHsECptd/v+LEN
hggF9WebKSaQ6XP2nDLy0R2VH/6EgJnF3Ubq/kP9LvtOpW/LH8s8PcCZHbnlKzNN
nTnA6VMt2wwAyLGLn7O9n9OCOWwcOOcaJEBTJ3g7o0DnAFtWm9UV0vKF4yKu+THV
h+eaY8f29PFPrY6zs/qcaBxXm7nSNZP1R+ZPtymRyHe+7Mas7DVAhCz5M0hcftae
I8bM8zVpQkNiVn1TBY+8XBA0vsJg6AIS20XfMgEO93RtyZKCI94ZFoGq+N+6akPi
vMU8GIoMKiAyTlCS4EdEQbYvPlAyiwJxUz//nc+HWf3qp87gYDKkSC1NmLDiRRCg
GtDjPX+WRtjHC0esqFMGfcXkN60X/daIA1RWESH6z51H8qw26yapeEs5oTaG9HSo
dtkn/lUGn8aax1obRamb8mlTOaPZOAjyhIWRx2ubMMZ8XFyZB5NxkszNo/jdlVQk
3tIwT+p34zmEEe+iTiGrsFUDAFNIXn5rPixJVBjBZzaxRgrL065cdG+gmbEjfgQ+
ThKU/fbxmM4=
=/JNK
-----END PGP SIGNATURE-----
Merge tag 'dma' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull samsung arm-soc dma changes from Arnd Bergmann:
"Some platforms are not yet converted to use the dmaengine framework,
including some of the samsung SoCs. In the meantime, we treat this as
platform code and merge the patches through the arm-soc tree."
* tag 'dma' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SAMSUNG: Fix compiler warning in dma-ops.c file
ASoC: follow the updated samsung DMA common operations
spi/s3c64xx: Add the use of DMA config operation
ARM: SAMSUNG: Add config() function in DMA common operations
This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part
in here is extending the am33xx support in the omap platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Qclg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific updates from Arnd Bergmann:
"This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part in
here is extending the am33xx support in the omap platform."
Fix up trivial conflicts in arch/arm/mach-{imx/mach-mx35_3ds.c, tegra/Makefile}
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: LPC32xx: Add PWM support
ARM: LPC32xx: Add PWM clock
ARM: LPC32xx: Set system serial based on cpu unique id
ARM: vexpress: Config option for early printk console
ARM: vexpress: Add Device Tree for V2P-CA15_CA7 core tile
ARM: vexpress: Convert V2P-CA15 Device Tree to 64 bit addresses
ARM: vexpress: Add fixed regulator for SMSC
ARM: vexpress: Add missing SP804 interrupt in motherboard's DTS files
ARM: vexpress: Initial common clock support
ARM: SAMSUNG: Introduce Kconfig variable for Samsung custom clk API
ARM: EXYNOS: Add missing static storage class specifier in pmu.c file
ARM: EXYNOS: Make combiner_init function static
ARM: EXYNOS: Update HSOTG PHY clock setting for EXYNOS4X12
ARM: versatile: Make plat-versatile clock optional
ARM: vexpress: Check master site in daughterboard's sysctl operations
ARM: vexpress: remove automatic errata workaround selection
ARM: LPC32xx: Adjust to pl08x DMA interface changes
ARM: EXYNOS: Clear SYS_WDTRESET bit to use watchdog reset
ARM: imx: fix mx51 ehci setup errors
ARM: imx: make ehci power/oc polarities configurable
...
These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should
not be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4zvd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull general arm-soc cleanups from Arnd Bergmann:
"These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should not
be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra."
Resolve trivial conflict in arch/arm/mach-omap2/clockdomains3xxx_data.c
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
ARM: S3C24XX: Remove unused GPIO definitions for Openmoko GTA02 board
ARM: S3C24XX: Remove unused GPIO definitions for port J
ARM: S3C24XX: Remove unused GPA, GPE, GPH bank GPIO aliases
ARM: S3C24XX: Convert the touchscreen setup code to common GPIO API
ARM: S3C24XX: Convert the PM code to gpiolib API
ARM: S3C24XX: Convert QT2410 board file to the gpiolib API
ARM: S3C24XX: Convert SMDK board file to the gpiolib API
ARM: S3C24XX: Free the backlight gpio requested in Mini2440 board code
ARM: imx: remove unused pdata from device macros
ARM: imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX_SSI from MACH_MX25_3DS
ARM: at91: fix new build errors
ARM: at91: add AIC5 support
ARM: at91: remove mach/irqs.h
ARM: at91: sparse irq support
ARM: at91: at91 based machines specify their own irq handler at run time
ARM: at91: remove static irq priorities for sam9x5
ARM: at91: add of irq priorities support
...
These were submitted as bug fixes before v3.5 but not considered
important enough to be included in it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=5gW4
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical arm-soc bug fixes from Arnd Bergmann:
"These were submitted as bug fixes before v3.5 but not considered
important enough to be included in it."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM:vt8500: Convert to use .restart and remove arch_reset()
ARM: davinci: da8xx: fix interrupt handling
ARM: OMAP2+: fix CONFIG_CPU_IDLE dependency on CONFIG_PM
ARM: mxs/tx28: fix odd include
ARM: OMAP: remove unused cpu detection macros
ARM: OMAP: fix typos related to OMAP330
ARM: OMAP7XX: Remove omap730.h and omap850.h
ARM: OMAP2+: fix naming collision of variable nr_irqs
ARM: OMAP: omap2plus_defconfig: Enable EXT4 support
ARM: OMAP depends on MMU
arm: omap3: am35x: Set proper powerdomain states
ARM: OMAP AM35x: clockdomain data: Fix clockdomain dependencies
ARM: OMAP AM35x: EMAC/MDIO integration: Add Davinci EMAC/MDIO hwmod support
ARM: OMAP: AM35xx: fix UART4 softreset
ARM: OMAP AM35xx: clock and hwmod data: fix UART4 data
ARM: OMAP AM35xx: clock and hwmod data: fix AM35xx HSOTGUSB hwmod
ARM: OMAP: Fix dts files w/ status property: "disable" -> "disabled"
ARM: OMAP: beagle: Set USB Host Port 1 to OMAP_USBHS_PORT_MODE_UNUSED
ARM: OMAP2: twl-common: Fix compiler warning
ARM: OMAP: fix the ads7846 init code
...
Pull the big VFS changes from Al Viro:
"This one is *big* and changes quite a few things around VFS. What's in there:
- the first of two really major architecture changes - death to open
intents.
The former is finally there; it was very long in making, but with
Miklos getting through really hard and messy final push in
fs/namei.c, we finally have it. Unlike his variant, this one
doesn't introduce struct opendata; what we have instead is
->atomic_open() taking preallocated struct file * and passing
everything via its fields.
Instead of returning struct file *, it returns -E... on error, 0
on success and 1 in "deal with it yourself" case (e.g. symlink
found on server, etc.).
See comments before fs/namei.c:atomic_open(). That made a lot of
goodies finally possible and quite a few are in that pile:
->lookup(), ->d_revalidate() and ->create() do not get struct
nameidata * anymore; ->lookup() and ->d_revalidate() get lookup
flags instead, ->create() gets "do we want it exclusive" flag.
With the introduction of new helper (kern_path_locked()) we are rid
of all struct nameidata instances outside of fs/namei.c; it's still
visible in namei.h, but not for long. Come the next cycle,
declaration will move either to fs/internal.h or to fs/namei.c
itself. [me, miklos, hch]
- The second major change: behaviour of final fput(). Now we have
__fput() done without any locks held by caller *and* not from deep
in call stack.
That obviously lifts a lot of constraints on the locking in there.
Moreover, it's legal now to call fput() from atomic contexts (which
has immediately simplified life for aio.c). We also don't need
anti-recursion logics in __scm_destroy() anymore.
There is a price, though - the damn thing has become partially
asynchronous. For fput() from normal process we are guaranteed
that pending __fput() will be done before the caller returns to
userland, exits or gets stopped for ptrace.
For kernel threads and atomic contexts it's done via
schedule_work(), so theoretically we might need a way to make sure
it's finished; so far only one such place had been found, but there
might be more.
There's flush_delayed_fput() (do all pending __fput()) and there's
__fput_sync() (fput() analog doing __fput() immediately). I hope
we won't need them often; see warnings in fs/file_table.c for
details. [me, based on task_work series from Oleg merged last
cycle]
- sync series from Jan
- large part of "death to sync_supers()" work from Artem; the only
bits missing here are exofs and ext4 ones. As far as I understand,
those are going via the exofs and ext4 trees resp.; once they are
in, we can put ->write_super() to the rest, along with the thread
calling it.
- preparatory bits from unionmount series (from dhowells).
- assorted cleanups and fixes all over the place, as usual.
This is not the last pile for this cycle; there's at least jlayton's
ESTALE work and fsfreeze series (the latter - in dire need of fixes,
so I'm not sure it'll make the cut this cycle). I'll probably throw
symlink/hardlink restrictions stuff from Kees into the next pile, too.
Plus there's a lot of misc patches I hadn't thrown into that one -
it's large enough as it is..."
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (127 commits)
ext4: switch EXT4_IOC_RESIZE_FS to mnt_want_write_file()
btrfs: switch btrfs_ioctl_balance() to mnt_want_write_file()
switch dentry_open() to struct path, make it grab references itself
spufs: shift dget/mntget towards dentry_open()
zoran: don't bother with struct file * in zoran_map
ecryptfs: don't reinvent the wheels, please - use struct completion
don't expose I_NEW inodes via dentry->d_inode
tidy up namei.c a bit
unobfuscate follow_up() a bit
ext3: pass custom EOF to generic_file_llseek_size()
ext4: use core vfs llseek code for dir seeks
vfs: allow custom EOF in generic_file_llseek code
vfs: Avoid unnecessary WB_SYNC_NONE writeback during sys_sync and reorder sync passes
vfs: Remove unnecessary flushing of block devices
vfs: Make sys_sync writeout also block device inodes
vfs: Create function for iterating over block devices
vfs: Reorder operations during sys_sync
quota: Move quota syncing to ->sync_fs method
quota: Split dquot_quota_sync() to writeback and cache flushing part
vfs: Move noop_backing_dev_info check from sync into writeback
...
The current mpic code creates a linear revmap just big enough for all
the sources, which happens to miss the IPIs and timers on some machines.
This will in turn break when the irqdomain code loses the fallback of
doing a linear search when the revmap fails (and really slows down IPIs
otherwise).
This happens for example on the U4 based Apple machines such as the
dual core PowerMac G5s.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull x86/mce changes from Ingo Molnar:
"This tree improves the AMD thresholding bank code and includes a
memory fault signal handling fixlet."
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix siginfo_t->si_addr value for non-recoverable memory faults
x86, MCE, AMD: Update copyrights and boilerplate
x86, MCE, AMD: Give proper names to the thresholding banks
x86, MCE, AMD: Make error_count read only
x86, MCE, AMD: Cleanup reading of error_count
x86, MCE, AMD: Print decimal thresholding values
x86, MCE, AMD: Move shared bank to node descriptor
x86, MCE, AMD: Remove local_allocate_... wrapper
x86, MCE, AMD: Remove shared banks sysfs linking
x86, amd_nb: Export model 0x10 and later PCI id
* ACPI conversion to PM handling based on struct dev_pm_ops.
* Conversion of a number of platform drivers to PM handling based on struct
dev_pm_ops and removal of empty legacy PM callbacks from a couple of PCI
drivers.
* Suspend-to-both for in-kernel hibernation from Bojan Smojver.
* cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti U Murthy.
* cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
* Suspend and hibernate fixes from Srivatsa S. Bhat and Colin Cross.
* Generic PM domains framework updates.
* RTC CMOS wakeup signaling update from Paul Fox.
* sparse warnings fixes from Sachin Kamat.
* Build warnings fixes for the generic PM domains framework and PM sysfs code.
* sysfs switch for printing device suspend times from Sameer Nanda.
* Documentation fix from Oskar Schirmer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=vC4/
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
- ACPI conversion to PM handling based on struct dev_pm_ops.
- Conversion of a number of platform drivers to PM handling based on
struct dev_pm_ops and removal of empty legacy PM callbacks from a
couple of PCI drivers.
- Suspend-to-both for in-kernel hibernation from Bojan Smojver.
- cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti
Murthy.
- cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
- Suspend and hibernate fixes from Srivatsa Bhat and Colin Cross.
- Generic PM domains framework updates.
- RTC CMOS wakeup signaling update from Paul Fox.
- sparse warnings fixes from Sachin Kamat.
- Build warnings fixes for the generic PM domains framework and PM
sysfs code.
- sysfs switch for printing device suspend times from Sameer Nanda.
- Documentation fix from Oskar Schirmer.
* tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (70 commits)
cpufreq: Fix sysfs deadlock with concurrent hotplug/frequency switch
EXYNOS: bugfix on retrieving old_index from freqs.old
PM / Sleep: call early resume handlers when suspend_noirq fails
PM / QoS: Use NULL pointer instead of plain integer in qos.c
PM / QoS: Use NULL pointer instead of plain integer in pm_qos.h
PM / Sleep: Require CAP_BLOCK_SUSPEND to use wake_lock/wake_unlock
PM / Sleep: Add missing static storage class specifiers in main.c
cpuilde / ACPI: remove time from acpi_processor_cx structure
cpuidle / ACPI: remove usage from acpi_processor_cx structure
cpuidle / ACPI : remove latency_ticks from acpi_processor_cx structure
rtc-cmos: report wakeups from interrupt handler
PM / Sleep: Fix build warning in sysfs.c for CONFIG_PM_SLEEP unset
PM / Domains: Fix build warning for CONFIG_PM_RUNTIME unset
olpc-xo15-sci: Use struct dev_pm_ops for power management
PM / Domains: Replace plain integer with NULL pointer in domain.c file
PM / Domains: Add missing static storage class specifier in domain.c file
PM / crypto / ux500: Use struct dev_pm_ops for power management
PM / IPMI: Remove empty legacy PCI PM callbacks
tpm_nsc: Use struct dev_pm_ops for power management
tpm_tis: Use struct dev_pm_ops for power management
...
Lots and lots of fixes from Axel and some others here, plus some framework
enhancements which continue the theme of factoring code out of the drivers
and into the core.
- Initial framework support for GPIO controlled enable signals, saving a
bunch of code in drivers.
- Move fixed regulator enable time and voltage mapping table
specifications to data.
- Used some of the recent framework enhancements to make voltage change
notifications more useful, passing the voltage in as an argument to the
notification.
- Fixed the pattern used for finding individual regulators on a device
to not rely on the node name, supporting the use of multiple PMICs of
the same type in the system.
- New drivers for Maxim MAX77686, TI LP872x and LP8788, Samsung S2MPS11,
and Wolfson Arizona microphone supplies and LDOs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Nv8m
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Lots and lots of fixes from Axel and some others here, plus some
framework enhancements which continue the theme of factoring code out
of the drivers and into the core.
- Initial framework support for GPIO controlled enable signals,
saving a bunch of code in drivers.
- Move fixed regulator enable time and voltage mapping table
specifications to data.
- Used some of the recent framework enhancements to make voltage
change notifications more useful, passing the voltage in as an
argument to the notification.
- Fixed the pattern used for finding individual regulators on a
device to not rely on the node name, supporting the use of multiple
PMICs of the same type in the system.
- New drivers for Maxim MAX77686, TI LP872x and LP8788, Samsung
S2MPS11, and Wolfson Arizona microphone supplies and LDOs."
* tag 'regulator-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (176 commits)
regulator: add new lp8788 regulator driver
regulator: mc13xxx: Remove extern function declaration for mc13xxx_sw_regulator
regulator: tps65910: set input_supply on desc unconditionally
regulator: palmas: Fix calcuating selector in palmas_map_voltage_smps
regulator: lp872x: Simplify implementation of lp872x_find_regulator_init_data()
regulator: twl: Fix list_voltate for twl6030ldo_ops
regulator: twl: Convert twl6030ldo_ops to [get|set]_voltage_sel
regulator: twl: Fix the formula to calculate vsel and voltage for twl6030ldo
regulator: s5m8767: Properly handle gpio_request failure
regulator: max8997: Properly handle gpio_request failure
regulator: tps62360: use devm_* for gpio request
regulator: tps6586x: add support for input supply
regulator: tps65217: Add device tree support
regulator: aat2870: Remove unused min_uV and max_uV from struct aat2870_regulator
regulator: aat2870: Convert to regulator_list_voltage_table
regulator: da9052: initialize of_node param for regulator register
regulator: Add REGULATOR_STATUS_UNDEFINED.
regulator: Fix a typo in regulator_mode_to_status() core function.
regulator: s2mps11: Use sec_reg_write rather than sec_reg_update when mask is 0xff
regulator: s2mps11: Fix wrong setting for config.dev
...
Pull a x86/build change from Ingo Molnar.
This makes the default stack alignment on x86-64 be just 8, allowing for
improved code generation (it can avoid some unnecessary extra alignment
logic and use just pure push/pop sequences) and smaller stack frames.
We can't generally do SSE with 16-byte alignment issues in the kernel anyway.
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, gcc: Use -mpreferred-stack-boundary=3 if supported
Pull x86/uv changes from Ingo Molnar:
"UV2 BAU productization fixes.
The BAU (Broadcast Assist Unit) is SGI's fancy out of line way on UV
hardware to do TLB flushes, instead of the normal APIC IPI methods.
The commits here fix / work around hangs in their latest hardware
iteration (UV2).
My understanding is that the main purpose of the out of line
signalling channel is to improve scalability: the UV APIC hardware
glue does not handle broadcasting to many CPUs very well, and this
matters most for TLB shootdowns.
[ I don't agree with all aspects of the current approach: in hindsight
it would have been better to link the BAU at the IPI/APIC driver
level instead of the TLB shootdown level, where TLB flushes are
really just one of the uses of broadcast SMP messages. Doing that
would improve scalability in some other ways and it would also
remove a few uglies from the TLB path. It would also be nice to
push more is_uv_system() tests into proper x86_init or x86_platform
callbacks. Cliff? ]"
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/uv: Work around UV2 BAU hangs
x86/uv: Implement UV BAU runtime enable and disable control via /proc/sgi_uv/
x86/uv: Fix the UV BAU destination timeout period
Pull x86/reboot changes from Ingo Molnar:
"Now that the revampted x86 real-mode trampoline code is upstream and
seems to be working well, we can extend the 64-bit reboot code to be
as capable as the 32-bit one."
* 'x86-reboot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, reboot: Be more paranoid in 64-bit reboot=bios
x86, reboot: Drop redundant write of reboot_mode
x86-64, reboot: Allow reboot=bios and reboot-cpu override on x86-64
Pull x86 platform changes from Ingo Molnar:
"This tree mostly involves various APIC driver cleanups/robustization,
and vSMP motivated platform callback improvements/cleanups"
Fix up trivial conflict due to printk cleanup right next to return value
change.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
Revert "x86/early_printk: Replace obsolete simple_strtoul() usage with kstrtoint()"
x86/apic/x2apic: Use multiple cluster members for the irq destination only with the explicit affinity
x86/apic/x2apic: Limit the vector reservation to the user specified mask
x86/apic: Optimize cpu traversal in __assign_irq_vector() using domain membership
x86/vsmp: Fix vector_allocation_domain's return value
irq/apic: Use config_enabled(CONFIG_SMP) checks to clean up irq_set_affinity() for UP
x86/vsmp: Fix linker error when CONFIG_PROC_FS is not set
x86/apic/es7000: Make apicid of a cluster (not CPU) from a cpumask
x86/apic/es7000+summit: Always make valid apicid from a cpumask
x86/apic/es7000+summit: Fix compile warning in cpu_mask_to_apicid()
x86/apic: Fix ugly casting and branching in cpu_mask_to_apicid_and()
x86/apic: Eliminate cpu_mask_to_apicid() operation
x86/x2apic/cluster: Vector_allocation_domain() should return a value
x86/apic/irq_remap: Silence a bogus pr_err()
x86/vsmp: Ignore IOAPIC IRQ affinity if possible
x86/apic: Make cpu_mask_to_apicid() operations check cpu_online_mask
x86/apic: Make cpu_mask_to_apicid() operations return error code
x86/apic: Avoid useless scanning thru a cpumask in assign_irq_vector()
x86/apic: Try to spread IRQ vectors to different priority levels
x86/apic: Factor out default vector_allocation_domain() operation
...
Pull debug-for-linus git tree from Ingo Molnar.
Fix up trivial conflict in arch/x86/kernel/cpu/perf_event_intel.c due to
a printk() having changed to a pr_info() differently in the two branches.
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Move call to print_modules() out of show_regs()
x86/mm: Mark free_initrd_mem() as __init
x86/microcode: Mark microcode_id[] as __initconst
x86/nmi: Clean up register_nmi_handler() usage
x86: Save cr2 in NMI in case NMIs take a page fault (for i386)
x86: Remove cmpxchg from i386 NMI nesting code
x86: Save cr2 in NMI in case NMIs take a page fault
x86/debug: Add KERN_<LEVEL> to bare printks, convert printks to pr_<level>
Pull x86/asm changes from Ingo Molnar:
"Assorted single-commit improvements, as usual"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/mtrr: Slightly simplify print_mtrr_state()
x86/mm/mtrr: Fix alignment determination in range_to_mtrr()
x86/copy_user_generic: Optimize copy_user_generic with CPU erms feature
x86/alternatives: Use atomic_xchg() instead atomic_dec_and_test() for stop_machine_text_poke()
Pull perf events changes from Ingo Molnar:
"- kernel side:
- Intel uncore PMU support for Nehalem and Sandy Bridge CPUs, we
support both the events available via the MSR and via the PCI
access space.
- various uprobes cleanups and restructurings
- PMU driver quirks by microcode version and required x86 microcode
loader cleanups/robustization
- various tracing robustness updates
- static keys: remove obsolete static_branch()
- tooling side:
- GTK browser improvements
- perf report browser: support screenshots to file
- more automated tests
- perf kvm improvements
- perf bench refinements
- build environment improvements
- pipe mode improvements
- libtraceevent updates, we have now hopefully merged most bits with
the out of tree forked code base
... and many other goodies."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (138 commits)
tracing: Check for allocation failure in __tracing_open()
perf/x86: Fix intel_perfmon_event_mapformatting
jump label: Remove static_branch()
tracepoint: Use static_key_false(), since static_branch() is deprecated
perf/x86: Uncore filter support for SandyBridge-EP
perf/x86: Detect number of instances of uncore CBox
perf/x86: Fix event constraint for SandyBridge-EP C-Box
perf/x86: Use 0xff as pseudo code for fixed uncore event
perf/x86: Save a few bytes in 'struct x86_pmu'
perf/x86: Add a microcode revision check for SNB-PEBS
perf/x86: Improve debug output in check_hw_exists()
perf/x86/amd: Unify AMD's generic and family 15h pmus
perf/x86: Move Intel specific code to intel_pmu_init()
perf/x86: Rename Intel specific macros
perf/x86: Fix USER/KERNEL tagging of samples
perf tools: Split event symbols arrays to hw and sw parts
perf tools: Split out PE_VALUE_SYM parsing token to SW and HW tokens
perf tools: Add empty rule for new line in event syntax parsing
perf test: Use ARRAY_SIZE in parse events tests
tools lib traceevent: Cleanup realloc use
...
This reverts commit fbd24153c4.
This commit is subtly buggy: kstrto*int() can return an error but
it's not checked in every path. simple_strtoul() on the other hand
could not fail, so this patch subtly intruduces new failure modes.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Link: http://lkml.kernel.org/r/1338424803.3569.5.camel@lorien2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
From Kukjin Kim <kgene.kim@samsung.com>:
It is including new exynos_defconfig for DT configuration of exynos4
and exynos5 together. The old exynos4_defconfig will be used for non-DT
for a while and we will try to move on using exynos_defconfig for only DT.
* samsung/defconfig:
ARM: exynos_defconfig: enable more platforms in defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the new EXYNOS5 platforms in the defconfig, and enables DT
support on EXYNOS4.
Other options enabled: USB host, EXT3/4, regulators and tps65090,
networking and a few of the common usb ethernet adapters as well as the
smsc911x controller used on some boards.
I enabled EFI_PARTITION, since it's used on some filesystem images I'm
using. I didn't see a need to keep Solaris and BSD partition format
still enabled.
Finally, framebuffer console, logo and fonts were enabled.
Note that enabling some of these options introduces build coverage
previously missing, thus introducing a few build errors and warnings
for which fixes have been sent out already.
Signed-off-by: Olof Johansson <olof@lixom.net>
[kgene.kim@samsung.com: restored exynos4_defconfig from original]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Kukjin Kim <kgene.kim@samsung.com>:
It is including several changes for samsung boards.
* 'next/board-samsung-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add leds status1 and status2 on Origen board
ARM: S3C64XX: Mark most Cragganmore initdata devinitdata
ARM: EXYNOS: Add missing .reserve field to SMDKC210
ARM: EXYNOS: Add DRM device to SMDK4X12 board
ARM: S3C64XX: Clean up after SPI driver platform data updates
ARM: SAMSUNG: no need to set the value for clk_xusbxti when it is 24Mhz
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CONFIG_EARLY_PRINTK is the only feature that might use command line
parsing in the decompression stage. If it is disabled then we can
exclude the related code to save space. This can result in an estimated
space savings of 2240 bytes from the compressed kernel image.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-8-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Removes early_serial_console.c code if we don't have the config option that
enables it (EARLY_PRINTK). When disabling this code, make early_serial_base a
constant 0 to allow the compiler to optimize away the code that checks for
early_serial_base.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-7-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
As we're no longer using the flag we don't need to extract the value from the
command line and store it. This is a step towards removing command line
parameter code.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-6-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Changed putstr flagging from parameter to conditional compilation for puts,
debug_putstr, and error_putstr. This allows for space savings since most
configurations won't use this feature.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-5-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For consistency we changed the error output path to match the new debug path.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-4-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Change all instances of if (debug) putstr(...) to a new debug_putstr(...).
This allows a future change to conditionally stub out debug_putstr to save
space.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-3-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There are only 3 uses of the quiet flag and they all protect output that
is only useful for debugging the stub, therefore we switched to using the
debug flag for all extra output.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-2-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
As things currently stand, traditional EFI boot loaders and the EFI
boot stub are carrying essentially the same initialisation code
required to setup an EFI machine for booting a kernel. There's really
no need to have this code in two places and the hope is that, with
this new protocol, initialisation and booting of the kernel can be
left solely to the kernel's EFI boot stub. The responsibilities of the
boot loader then become,
o Loading the kernel image from boot media
File system code still needs to be carried by boot loaders for the
scenario where the kernel and initrd files reside on a file system
that the EFI firmware doesn't natively understand, such as ext4, etc.
o Providing a user interface
Boot loaders still need to display any menus/interfaces, for example
to allow the user to select from a list of kernels.
Bump the boot protocol number because we added the 'handover_offset'
field to indicate the location of the handover protocol entry point.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-and-Tested-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1342689828-16815-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
From Roland Stigge <stigge@antcom.de>:
this LPC32xx core update (branch lpc32xx/core2) builds upon the
previously provided lpc32xx/core-fixes. Basically including PWM support
(for the PWM driver from Alexandre already in the pwm tree), and
CPU ID.
* 'lpc32xx/core2' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Add PWM support
ARM: LPC32xx: Add PWM clock
ARM: LPC32xx: Set system serial based on cpu unique id
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Roland Stigge <stigge@antcom.de>:
this is a late addition to LPC32xx DTS files for v3.6.
* 'lpc32xx/dts2' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Add PWM to base dts file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The incompatible parameter of flush_tlb_mm_range cause build warning.
Fix it by correct parameter.
Ingo Molnar found that this could also cause a user space crash.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1342747103-19765-1-git-send-email-alex.shi@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add the RDSEED and ADX features documented in section 9.1 of the Intel
Architecture Instruction Set Extensions Programming Reference,
document 319433, version 013b, available from
http://software.intel.com/en-us/avx/
The PREFETCHW bit is already supported in Linux under the name
3DNOWPREFETCH.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-lgr6482ufk1bvxzvc2hr8qbp@git.kernel.org
When more than 1 source id is in use for the same GSI, we have the
following race related to handling irq_states race:
CPU 0 clears bit 0. CPU 0 read irq_state as 0. CPU 1 sets level to 1.
CPU 1 calls kvm_ioapic_set_irq(1). CPU 0 calls kvm_ioapic_set_irq(0).
Now ioapic thinks the level is 0 but irq_state is not 0.
Fix by performing all irq_states bitmap handling under pic/ioapic lock.
This also removes the need for atomics with irq_states handling.
Reported-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Pull late MIPS fixes from Ralf Baechle:
"This fixes a number of lose ends in the MIPS code and various bug
fixes.
Aside of dropping some patch that should not be in this pull request
everything has sat in -next for quite a while and there are no known
issues.
The biggest patch in this patch set moves the allocation of an array
that is aliased to a function (for runtime generated code) to
assembler code. This avoids an issue with certain toolchains when
building for microMIPS."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (35 commits)
MIPS: PCI: Move fixups from __init to __devinit.
MIPS: Fix bug.h MIPS build regression
MIPS: sync-r4k: remove redundant irq operation
MIPS: smp: Warn on too early irq enable
MIPS: call set_cpu_online() on cpu being brought up with irq disabled
MIPS: call ->smp_finish() a little late
MIPS: Yosemite: delay irq enable to ->smp_finish()
MIPS: SMTC: delay irq enable to ->smp_finish()
MIPS: BMIPS: delay irq enable to ->smp_finish()
MIPS: Octeon: delay enable irq to ->smp_finish()
MIPS: Oprofile: Fix build as a module.
MIPS: BCM63XX: Fix BCM6368 IPSec clock bit
MIPS: perf: Fix build error caused by unused counters_per_cpu_to_total()
MIPS: Fix Magic SysRq L kernel crash.
MIPS: BMIPS: Fix duplicate header inclusion.
mips: mark const init data with __initconst instead of __initdata
MIPS: cmpxchg.h: Add missing include
MIPS: Malta may also be equipped with MIPS64 R2 processors.
MIPS: Fix typo multipy -> multiply
MIPS: Cavium: Fix duplicate ARCH_SPARSEMEM_ENABLE in kconfig.
...
LPC32xx SoC has a 128 bits unique id that can be used as a system
serial number, if none has been provided by atags or dt.
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
The current virtual timer interface is inherently per-cpu and hard to
use. The sole user of the interface is appldata which uses it to execute
a function after a specific amount of cputime has been used over all cpus.
Rework the virtual timer interface to hook into the cputime accounting.
This makes the interface independent from the CPU timer interrupts, and
makes the virtual timers global as opposed to per-cpu.
Overall the code is greatly simplified. The downside is that the accuracy
is not as good as the original implementation, but it is still good enough
for appldata.
Reviewed-by: Jan Glauber <jang@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
If lgr has not been initialized, the lgr_info_log() function currently
crashes because 'lgr_page' is not allocated. To fix this 'lgr_page'
is allocated statically now.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The SIU ALSA driver is not using the DMA device pointer for DMA channel
filtering any more, it can be now removed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Currently kexec in a PVonHVM guest fails with a triple fault because the
new kernel overwrites the shared info page. The exact failure depends on
the size of the kernel image. This patch moves the pfn from RAM into
MMIO space before the kexec boot.
The pfn containing the shared_info is located somewhere in RAM. This
will cause trouble if the current kernel is doing a kexec boot into a
new kernel. The new kernel (and its startup code) can not know where the
pfn is, so it can not reserve the page. The hypervisor will continue to
update the pfn, and as a result memory corruption occours in the new
kernel.
One way to work around this issue is to allocate a page in the
xen-platform pci device's BAR memory range. But pci init is done very
late and the shared_info page is already in use very early to read the
pvclock. So moving the pfn from RAM to MMIO is racy because some code
paths on other vcpus could access the pfn during the small window when
the old pfn is moved to the new pfn. There is even a small window were
the old pfn is not backed by a mfn, and during that time all reads
return -1.
Because it is not known upfront where the MMIO region is located it can
not be used right from the start in xen_hvm_init_shared_info.
To minimise trouble the move of the pfn is done shortly before kexec.
This does not eliminate the race because all vcpus are still online when
the syscore_ops will be called. But hopefully there is no work pending
at this point in time. Also the syscore_op is run last which reduces the
risk further.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
init_hvm_pv_info is called only in PVonHVM context, move it into ifdef.
init_hvm_pv_info does not fail, make it a void function.
remove arguments from init_hvm_pv_info because they are not used by the
caller.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Both have type struct shared_info so no cast is needed.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When switching tasks in a Xen PV guest, avoid updating the TLS
descriptors if they haven't changed. This improves the speed of
context switches by almost 10% as much of the time the descriptors are
the same or only one is different.
The descriptors written into the GDT by Xen are modified from the
values passed in the update_descriptor hypercall so we keep shadow
copies of the three TLS descriptors to compare against.
lmbench3 test Before After Improvement
--------------------------------------------
lat_ctx -s 32 24 7.19 6.52 9%
lat_pipe 12.56 11.66 7%
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When constructing the initial page tables, if the MFN for a usable PFN
is missing in the p2m then that frame is initially ballooned out. In
this case, zero the PTE (as in decrease_reservation() in
drivers/xen/balloon.c).
This is obviously safe instead of having an valid PTE with an MFN of
INVALID_P2M_ENTRY (~0).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Scott Jiang