n25q512a was rebranded to mt25qu512a after its spin off from STM.
mt25qu512a is different only in terms of operating frequency, the
JEDEC id is the same as in n25q512a.
Dual reads are supported (0x3b, 0x3c), set the SPI_NOR_DUAL_READ flag.
4-byte opcodes are supported, set the SPI_NOR_4B_OPCODES flag.
Tested Single I/O and QUAD I/O mode on LS1046FRWY.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: rename entry to "mt25qu512a (n25q512a)",
reword commit message, order entry by size, drop comment as it looked
redundant]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
We already pass a pointer to nor, we can obtain the sector_size
by dereferencing it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
This patch adds spi_nor_debugfs_init() for the debugfs initialization.
With this patch, we can read the partname and partid through the
debugfs.
The output of new debugfs nodes on my device are:
cat /sys/kernel/debug/mtd/mtd0/partid
spi-nor:ef6017
cat /sys/kernel/debug/mtd/mtd0/partname
w25q64dw
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a break from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put before
the break.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a break from the middle of the loop, there is
no put, thus causing a memory leak. Upon termination of the loop
(whether by break or a natural exit), either ret will have a non-zero
value or child will be NULL. Hence add an of_node_put() that will
execute only when ret has a non-zero value, as calling of_node_put() on
a possible NULL value does not cause any further issues.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Dedicate a function for getting the pointer to the flash_info
const struct. Trim a bit the spi_nor_scan() huge function.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Parsing of flash parameters were interleaved with setting of the
nor addr width. Dedicate a function for setting nor addr width.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
S3AN flashes use a specific opcode to read the status register.
We currently use the SPI_S3AN flag to decide whether this specific
SR read opcode should be used, but SPI_S3AN is about to disappear, so
let's add a new flag.
Note that we use the same bit as SPI_S3AN implies SPI_NOR_XSR_RDY and
vice versa.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
s3an_nor_scan() was overriding the opcode selection done in
spi_nor_default_setup(). Set nor->setup() method in order to
avoid the unnecessary call to spi_nor_default_setup().
Now that the call to spi_nor_default_setup() is skipped, set
mtd.erasesize to nor->info->sector_size, as it was when
spi_nor_select_erase() was called.
No dummy byte is required for the S3AN's Random Read command (0x03),
so no need to set nor->read_dummy.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
nor->params.setup() configures the SPI NOR memory. Useful for SPI NOR
flashes that have peculiarities to the SPI NOR standard, e.g.
different opcodes, specific address calculation, page size, etc.
Right now the only user will be the S3AN chips, but other
manufacturers can implement it if needed.
Move spi_nor_setup() related code in order to avoid a forward
declaration to spi_nor_default_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
In order to separate manufacturer quirks from the core we need to get
rid of all the manufacturer specific flags, like the
SNOR_F_S3AN_ADDR_DEFAULT one.
This can easily be replaced by a ->convert_addr() hook, which when
implemented will provide the core with an easy way to convert an
absolute address into something the flash understands.
Right now the only user are the S3AN chips, but other manufacturers
can implement it if needed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add a spansion_post_sfdp_fixups() function to fix the erase opcode,
erase sector size and set the SNOR_F_4B_OPCODES flag.
This way, all spansion related quirks are placed in the
spansion_post_sfdp_fixups() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
SFDP tables are sometimes wrong and we need a way to override the
config chosen by the SFDP parsing logic without discarding all of it.
Add a new hook called after the SFDP parsing has taken place to deal
with such problems.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add the SNOR_F_HAS_LOCK flag and set it when SPI_NOR_HAS_LOCK is set
in the flash_info entry or when it's a Micron or ST flash.
Move the locking hooks in a separate struct so that we have just
one field to update when we change the locking implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use ->default_init() hook, introduce
spi_nor_late_init_params(), set ops in nor->params]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The procedure used to enable 4 byte addressing mode depends on the NOR
device, so let's provide a hook so that manufacturer specific handling
can be implemented in a sane way.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use nor->params.set_4byte() instead of
nor->set_4byte()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add functions to delimit what the chunks of code do:
static void spi_nor_init_params()
{
spi_nor_info_init_params()
spi_nor_manufacturer_init_params()
spi_nor_sfdp_init_params()
}
Add descriptions to all methods.
spi_nor_init_params() becomes of type void, as all its children
return void.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The goal is to move the quad_enable manufacturer specific init in the
nor->manufacturer->fixups->default_init()
The legacy quad_enable() implementation is spansion_quad_enable(),
select this method by default.
Set specific manufacturer fixups->default_init() hooks to overwrite
the default quad_enable() implementation when needed.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
gd25q256 needs to tweak the ->quad_enable() implementation and the
->default_init() fixup hook is the perfect place to do that. This way,
if we ever need to tweak more things for this flash, we won't have to
add new fields in flash_info.
We can get rid of the flash_info->quad_enable field as gd25q256 was
the only user.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use ->default_init() hook instead of
->post_sfdp()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
As of now, the flash parameters initialization logic is as following:
a/ default flash parameters init in spi_nor_init_params()
b/ manufacturer specific flash parameters updates, split across entire
spi-nor core code
c/ flash parameters updates based on SFDP tables
d/ post BFPT flash parameter updates
In the quest of removing the manufacturer specific code from the spi-nor
core, we want to impose a timeline/priority on how the flash parameters
are updated. The following sequence of calls is pursued:
1/ spi-nor core parameters init based on 'flash_info' struct:
spi_nor_info_init_params()
which can be overwritten by:
2/ MFR-based manufacturer flash parameters init:
nor->manufacturer->fixups->default_init()
which can be overwritten by:
3/ specific flash_info tweeks done when decisions can not be done just on
MFR:
nor->info->fixups->default_init()
which can be overwritten by:
4/ SFDP tables flash parameters init - SFDP knows better:
spi_nor_sfdp_init_params()
which can be overwritten by:
5/ post SFDP tables flash parameters updates - in case manufacturers get
the serial flash tables wrong or incomplete.
nor->info->fixups->post_sfdp()
The later can be extended to nor->manufacturer->fixups->post_sfdp() if
needed.
This patch opens doors for steps 2/ and 3/.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
All flash parameters and settings should reside inside
'struct spi_nor_flash_parameter'. Move the SMPT parsed erase map
from 'struct spi_nor' to 'struct spi_nor_flash_parameter'.
Please note that there is a roll-back mechanism for the flash
parameter and settings, for cases when SFDP parser fails. The SFDP
parser receives a Stack allocated copy of nor->params, called
sfdp_params, and uses it to retrieve the serial flash discoverable
parameters. JESD216 SFDP is a standard and has a higher priority
than the default initialized flash parameters, so will overwrite the
sfdp_params data when needed. All SFDP code uses the local copy of
nor->params, that will overwrite it in the end, if the parser succeds.
Saving and restoring the nor->params.erase_map is no longer needed,
since the SFDP code does not touch it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
All flash parameters and settings should reside inside
'struct spi_nor_flash_parameter'. Drop the local copy of
quad_enable() and use the one from 'struct spi_nor_flash_parameter'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The Flash parameters and settings are now stored in 'struct spi_nor'.
Use this instead of the stack allocated params.
Few functions stop passing pointer to params, as they can get it from
'struct spi_nor'. spi_nor_parse_sfdp() and children will keep passing
pointer to params because of the roll-back mechanism: in case the
parsing of SFDP fails, the legacy flash parameter and settings will be
restored.
Zeroing params is no longer needed because all SPI NOR users kzalloc
'struct spi_nor'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The scope is to move all [FLASH-SPECIFIC] parameters and settings
from 'struct spi_nor' to 'struct spi_nor_flash_parameter'.
'struct spi_nor_flash_parameter' describes the hardware capabilities
and associated settings of the SPI NOR flash memory. It includes
legacy flash parameters and settings that can be overwritten by the
spi_nor_fixups hooks, or dynamically when parsing the JESD216
Serial Flash Discoverable Parameters (SFDP) tables. All SFDP params
and settings will fit inside 'struct spi_nor_flash_parameter'.
Move spi_nor_hwcaps related code to avoid forward declarations.
Add a forward declaration that we can't avoid: 'struct spi_nor' will
be used in 'struct spi_nor_flash_parameter'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl1i2wkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGcDQIAJINYON5WdDSFDpp
htva213hSIxYLix8Dc4cTMk8qT/P2MAj9pPYERuLwIxWZlfbduW6Fxy8bJANZ7k3
4cJ/IbmA5M5ZIaOJTTL45w8H0CMR/4mdPl5rb5k/Wkh449Cj101gZLlh0FEtR5zG
uDJecKSuHjH1ikySk6+zmRG5X+lq6wNY8NkuBtfwAwLffFc0ljQHwPUMJ8ojgqt/
p3ChNgtb/I6U6ExITlyktKdP59bAoHAoBiKKFZWw5yJWgXE2q4Sv9nT4Btkr5KdJ
9mnWnSaSLwptNCOtU4tKLwFIZP2WoVXGPNxxq4XLoTEuieXCqmikhc9tSSTwk+Tp
CKHN6wU=
=JkJ4
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl1mS78ACgkQS1VPR6WN
FOnqOwgAqerjkyzyleXrzvLVaUUhT4MrykMljakHFX6zt+ipi74bdOQRF+uG2A4v
DnhYXGfEiIRNco/4NkXEKWsOBKoWUIUISpxuBBRmEJEL9Y23WJ1czy8rPEWoVff3
BUY6sJ0kmltikRh0hBZhABa0lkbimV3WGiVB5ATpsO2whdJz3tN+k4GjWq12Sbls
V+ioN7eeJSRuufwVSFT3YcGT7uRX6/Fq21fX4XkWJp3IaftD8eo5pkO+XQFIeBKw
xB7g2zkkDG//jnzodjSc2RcpXda1i4a8Yx+6J2KJw7x1F5JVQN4VgmsARPFWsCID
Q7uhWqCVdW6cSBebwkHC1xf4fZSRmw==
=x4If
-----END PGP SIGNATURE-----
Merge tag 'v5.3-rc6' into spi-nor/next
Linux 5.3-rc6
Merge back latest release candidate, to include a fix that
we depend on for new development:
834de5c1aa ("mtd: spi-nor: Fix the disabling of write protection at init")
spi-nor.c issues 4B commands for some Flash chips bigger than 16Mbytes.
Xeon(R) D-1500 documentation mentions its Integrated PCH Logic supports
Flash chips up to 64Mbytes.
D-1500 Integrated PCH documenation however has inconsistencies regarding
FADDR register width and says nothing about particular commands issued
to support 64Mbytes of Flash.
Nevetheless the tests on Xeon(R) CPU D-1548 with 512Mbit Flash chips
Macronix MX25L51245G and Micron MT25QL512A showed that erase, write and
read operations work just fine after SPINOR_OP_READ_4B and
SPINOR_OP_READ_FAST_4B are white-listed (currently only
SPINOR_OP_READ_FAST_4B is used and only for Macronix).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
In spi_nor_parse_4bait(), 'dwords' is allocated through kmalloc(). However,
it is not deallocated in the following execution if spi_nor_read_sfdp()
fails, leading to a memory leak. To fix this issue, free 'dwords' before
returning the error.
Fixes: 816873eaee ("mtd: spi-nor: parse SFDP 4-byte Address Instruction Table")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The problem is that if "ret" is negative then when we check if
"ret > len", that condition is going to be true because of type
promotion. So this patch re-orders the code to check for negatives
first and preserve those error codes.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The current Cadence QSPI driver sometimes caused a
"rcu_sched self-detected stall" while writing large files.
Stall Report:
'# mtd_debug write /dev/mtd1 0 48816464 blob.img
[ 1815.454227] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1815.459789] rcu: 0-....: (2099 ticks this GP) idle=8c6/1/0x40000002
softirq=6492/6492 fqs=935
[ 1815.468442] rcu: (t=2100 jiffies g=8749 q=247)
<snip> (abbreviated backtrace)
[ 1815.772086] [<c05a3ea0>] (cqspi_exec_flash_cmd) (cqspi_read_reg)
[ 1815.786203] [<c05a5488>] (cqspi_read_reg) from (read_sr)
[ 1815.803790] [<c05a0330>] (read_sr) from
(spi_nor_wait_till_ready_with_timeout)
[ 1815.816610] [<c05a182c>] (spi_nor_wait_till_ready_with_timeout) from
(spi_nor_write+0x104/0x1d0)
[ 1815.836791] [<c05a1a44>] (spi_nor_write) from (part_write+0x50/0x58)
<snip>
[ 1815.997961] cadence-qspi ff809000.spi: Flash command execution timed out.
[ 1816.004733] error -110 reading SR
file_to_flash: write, size 0x2e8e150, n 0x2e8e150
write(): Connection timed out
This was caused by a tight loop in cqspi_wait_for_bit(). Fix by using
readl_relaxed_poll_timeout() which sleeps 10us while polling a register.
Fit onto 80 character line by truncating the bool clear parameter
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Currently, the Top/Bottom protection function (SPI_NOR_HAS_TB) is
implemented to fit some flashes with TB bit on SR.
s25fl512s has TBPROT bit on CR1, so the TB protection is not working on it.
Fix the wrong flag on s25fl512s.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Tiger Lake has the same SPI serial flash controller as Ice Lake.
Add Tiger Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This commit adds support for the SST sst26wf016b flash memory IC.
This IC was tested with "snps,dw-apb-ssi" SPI controller.
We don't test dual/quad reads however sst26wf016b flash's datasheet
advertises both dual and quad reads (and support of corresponding
commands)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Similar to w25q256 (besides not supporting QPI mode) but with different ID.
The "JVM" suffix is in the datasheet.
The datasheet indicates DUAL and QUAD are supported.
https://www.winbond.com/resource-files/w25q256jv%20spi%20revi%2010232018%20plus.pdf
Signed-off-by: Avi Fishman <avifishman70@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_spansion_clear_sr_bp() depends on spansion_quad_enable().
While spansion_quad_enable() is selected as default when
initializing the flash parameters, the nor->quad_enable() method
can be overwritten later on when parsing BFPT.
Select the write protection disable mechanism at spi_nor_init() time,
when the nor->quad_enable() method is already known.
Fixes: 191f5c2ed4 ("mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The spi-mem layer provides a spi_mem_supports_op() function to check
whether a specific operation is supported by the controller or not.
This is much more accurate than the hwcaps selection logic based on
SPI_{RX,TX}_ flags.
Rework the hwcaps selection logic to use spi_mem_supports_op() when
nor->spimem != NULL.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The m25p80 driver is actually a generic wrapper around the spi-mem
layer. Not only the driver name is misleading, but we'd expect such a
common logic to be directly available in the core. Another reason for
moving this code is that SPI NOR controller drivers should
progressively be replaced by SPI controller drivers implementing the
spi_mem_ops interface, and when the conversion is done, we should have
a single spi-nor driver directly interfacing with the spi-mem layer.
While moving the code we also fix a longstanding issue when
non-DMA-able buffers are passed by the MTD layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi-mem layer expects all buffers passed to it to be DMA'able. But
spi-nor layer mostly allocates buffers on stack for reading/writing to
registers and therefore are not DMA'able. Introduce bounce buffer to be
used to read/write to registers. This ensures that buffer passed to
spi-mem layer during register read/writes is DMA'able. With this change
nor->cmd-buf is no longer used, so drop it.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0qLr4ACgkQJWrqGEe9
VoQVCwf/ZCG5CldS3cs6B68kMJoZ/rJyJxBnxtIhffda2vw1KG/12o6XaDO9xA/R
EwYrOTzlYZxzCZsNvWyHepG3Kj3d38CJ52ZqhavjpihwMlKKOgW/K39xuKWCrfxS
sVMLz/UdrcsQfcPGAy7DSyqhzRAtupNxngCdEkIIMGFZWsv4uZfOFEGMrzUJ5RYN
/okIyUE7Iz0dRq1/KXSl365V1MS8QP2eHFuHrUd38+kJ8TJnQjXX3Bmdul4aNTx+
HIIpykovoAn5BZ0YA4lJL90zVoDOWysARwHIAMDvJa8zS0wDTU16Tj2M6AQK+a4x
hbIOOkeX0hTKpJvy7/khli5y1bn2mw==
=L+tV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl0V1XYACgkQS1VPR6WN
FOkBbQf+Iv2+vmoDGDCVGO4LZh+N/l0Sh/C31hJj5y7GVkCdwMJCvdOrGEhDkseu
Dc0gchT6uy52pAp4N0B88avC8fSJY0UwFRbnqUUA546R9Uf6h+gbGIZCX/rzZuIi
IDDNHc06qbpxpesfC5CowhY49QVGG+O0scgUOE2gKHOfd04kXu6gqIV0BvQZg80R
EpSgifHLUk/b2015FyqB5YFuc2K3HMmcWc6uJx4kSHPCXiCOx8aaEqjKvK9vL0h5
XOxXim5HhuzFqQ8vSPqvnKDokkuV3pcSUcaQyjQjrebTlectaDjGZlLF17Udm9Q9
I0zI+7deXK9L4roatEryzOdW0Ql3Hw==
=J5Uw
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.3-v2' of gitolite.kernel.org:pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
Get the reset control properties for the QSPI controller and bring them
out of reset. Most will have just one reset bit, but there is an additional
OCP reset bit that is used ECC. The OCP reset bit will also need to get
de-asserted as well. [1]
The reason this patch is needed is in the case where a bootloader leaves
the QSPI controller in a reset state, or a state where init cannot occur
successfully, the patch will put the QSPI controller into a clean state.
[1] https://www.intel.com/content/www/us/en/programmable/hps/arria-10/hps.html#reg_soc_top/sfo1429890575955.html
Suggested-by: Tien-Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: declare rstc and rstc_ocp on the same line]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
IS25LP256 gets BFPT_DWORD1_ADDRESS_BYTES_3_ONLY from BFPT table for
address width. But in actual fact the flash can support 4-byte address.
Use a post bfpt fixup hook to overwrite the address width advertised by
the BFPT.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0Pwk0ACgkQJWrqGEe9
VoS8nwf7B76jN39/g32Hfp4JT/B7cntrHzTGxfUT9NAhKa4MaI7FOU2eeTryaVdO
32OJlttV+r0Fu6p+In1VXCk4j1YlkcOaxqB1VXsMEaQ+Vt8ONVTbJX/cqyGC/ogq
MZlO8Rys4MGmq7vRiZ+1SD8lOV4qXgmX3D38NjUQ1oCAMCCgJgkWYFV2tv9Eie09
2CCT3IBFj+D34qaBiM+qocGtnzWfB9477A6ZeI4BwjUe1ZtoEYeIOrCXWiywabjM
msHRN1tNt5kfINnx0TkQFcnpbdDo5tMyTHCkEQt5Ewdae4vyCv7xTHTCZEttC7Ic
Rx2yONzrZGQVP4c27y22K954C1jGcg==
=ZiPm
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Set the raw NAND number of targets to the right value
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes
* tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes
mtd: rawnand: initialize ntargets with maxchips
This gets rid of the license boilerplate duplicated in each file.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Elkhart Lake has the same SPI serial flash controller as Ice Lake.
Add Elkhart Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Testing done on Mikrotik Routerboard RB450Gx4 board under
4.14.119 and 4.19.43 kernels. The test board does not support
Dual or Quad modes.
Datasheet at:
https://www.winbond.com/resource-files/w25q16jv%20spi%20revg%2003222018%20plus.pdf
Signed-off-by: Robert Marko <robimarko@gmail.com>
[tudor.ambarus@microchip.com: w25q16jv-im/jm and w25q16jv-iq/jq
have different jedec ids, fix flash name.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>