drm-next is forwarded to v4.20-rc1, and we need this to make
a patch series apply.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
It turns out that even new DW HDMI controllers exhibits same magenta
line issues as older versions.
Enable workaround for v2.12a.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-15-jernej.skrabec@siol.net
Allow to also drive a slave dw-mipi-dsi controller in a dual-dsi
setup. This will require additional implementation-specific
code to look up the slave instance and do specific setup.
Also will probably need code in the specific crtcs as dual-dsi
does not equal two separate dsi outputs.
To activate, the implementation-specific code should set the slave
using dw_mipi_dsi_set_slave() before calling __dw_mipi_dsi_bind().
v2:
- expect real interface number of lanes
- keep links to both master and slave
v3:
- remove unneeded separate variables
- remove unneeded second slave settings
- disable slave before master
- lane-sum calculation comments
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-7-heiko@sntech.de
With the regular means of adding the dsi-component in probe it creates
a race condition with the panel probing, as the panel device only gets
created after the dsi-bus got created.
When the panel-driver is build as a module it currently fails hard as the
panel cannot be probed directly:
dw_mipi_dsi_bind()
__dw_mipi_dsi_probe()
creates dsi bus
creates panel device
triggers panel module load
panel not probed (module not loaded or panel probe slow)
drm_bridge_attach
fails with -EINVAL due to empty panel_bridge
Additionally the panel probing can run concurrently with dsi bringup
making it possible that the panel can already be found but dsi-attach
hasn't finished running.
To solve that cleanly we may want to only create the component after
the panel has finished probing, by calling component_add from the
host-attach dsi callback.
As that is specific to glue drivers, add a new struct for host_ops
so that glue drivers can tell the bridge to call specific functions
after the common host-attach and before the common host-detach run.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-4-heiko@sntech.de
__dw_mipi_dsi_probe() does all the grabbing of resources and does it using
devm-helpers. So this is happening on each try of master bringup possibly
slowing down things a lot.
Drivers using the component framework may instead want to call
dw_mipi_dsi_probe separately in their probe function to setup resources
early. That way the dsi bus also gets created earlier and also not
recreated on each bind-try, so that attached panels can load their modules
and be probed way before the bridge-attach in the bind call.
So drop the call to __dw_mipi_dsi_probe and modify the function to take
a struct dw_mipi_dsi instead of the platform-device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-3-heiko@sntech.de
Right now the host is only unregistered when the driver is used via the
bridge api and not via the component api, leading to the host staying
registered in cases like probe deferral.
So move the host unregister to the general remove function, so that it
gets cleaned up in all cases.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-2-heiko@sntech.de
Let's solve the mystery of commit bf1178c989 ("drm/bridge:
ti-sn65dsi86: Add mystery delay to enable()"). Specifically the
reason we needed that mystery delay is that we weren't paying
attention to HPD.
Looking at the datasheet for the same panel that was tested for the
original commit, I see there's a timing "t3" that times from power on
to the aux channel being operational. This time is specced as 0 - 200
ms. The datasheet says that the aux channel is operational at exactly
the same time that HPD is asserted.
Scoping the signals on this board showed that HPD was asserted 84 ms
after power was asserted. That very closely matches the magic 70 ms
delay that we had. ...and actually, in my testing the 70 ms wasn't
quite enough of a delay and some percentage of the time the display
didn't come up until I bumped it to 100 ms (presumably 84 ms would
have worked too).
To solve this, we tried to hook up the HPD signal in the bridge.
...but in doing so we found that that the bridge didn't report that
HPD was asserted until ~280 ms after we powered it (!). This is
explained by looking at the sn65dsi86 datasheet section "8.4.5.1 HPD
(Hot Plug/Unplug Detection)". Reading there we see that the bridge
isn't even intended to report HPD until 100 ms after it's asserted.
...but that would have left us at 184 ms. The extra 100 ms
(presumably) comes from this part in the datasheet:
> The HPD state machine operates off an internal ring oscillator. The
> ring oscillator frequency will vary [ ... ]. The min/max range in
> the HPD State Diagram refers to the possible times based off
> variation in the ring oscillator frequency.
Given that the 280 ms we'll end up delaying if we hook up HPD is
_slower_ than the 200 ms we could just hardcode, for now we'll solve
the problem by just hardcoding a 200 ms delay in the panel driver
using the patch in this series ("drm/panel: simple: Support panels
with HPD where HPD isn't connected").
If we later find a panel that needs to use this bridge where we need
HPD then we'll have to come up with some new code to handle it. Given
the silly debouncing in the bridge chip, though, it seems unlikely.
One last note is that I tried to solve this through another way: In
ti_sn_bridge_enable() I tried to use various combinations of
dp_dpcd_writeb() and dp_dpcd_readb() to detect when the aux channel
was up. In theory that would let me detect _exactly_ when I could
continue and do link training. Unfortunately even if I did an aux
transfer w/out waiting I couldn't see any errors. Possibly I could
keep looping over link training until it came back with success, but
that seemed a little overly hacky to me.
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-4-dianders@chromium.org
This patch avoids that building the bridge/analogix source code with
smatch triggers complaints about inconsistent indenting. It also fixes
a typo in DRM_ERROR message, attch is replaced for attach.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016095336.15656-1-enric.balletbo@collabora.com
It's the default. The exported version was kinda a transition state,
before we made this the default.
To stop new atomic drivers from using it (instead of just relying on
the default) let's unexport it.
v2: rename the default implementation to a more fitting name and add a
comment (Laurent)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Pierre-Hugues Husson <phh@phh.me>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004202446.22905-3-daniel.vetter@ffwll.ch
In some IP implementations the reading of the phy-type may be broken.
One example are the Rockchip rk3228 and rk3328 socs that use a separate
vendor-type phy from Innosilicon but still report the HDMI20_TX type.
So allow the glue driver to force the vendor-phy for these cases.
In the future it may be necessary to allow forcing other types, but
for now we'll keep it simply to the case actually seen in the wild.
changes in v3:
- only allow forcing vendor type, as suggested by Laurent
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Zheng Yang <zhengyang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-2-heiko@sntech.de
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-3-heiko@sntech.de
The THC63LVD1024 is restricted to a pixel clock frequency in the range
of 8 to 135 MHz. Implement the bridge .mode_valid() operation
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
The Analogix DP bridge driver is pretty verbose, and outputs
things like
[ 619.414067] rockchip-dp ff970000.edp: Link Training Clock Recovery success
[ 619.429233] rockchip-dp ff970000.edp: Link Training success!
each time the display gets unblanked. While it is good to know
that the device is behaving correctly, users already know that
because they can see some video output.
Let's keep these messages for cases where we need to actually
debug the driver (we have dynamic debug to enable them at runtime
if need be), and let's keep the kernel quiet otherwise.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180805172857.2517-1-marc.zyngier@arm.com
This patch adds a 70ms mystery delay to the bridge driver in enable.
By experimentation, it seems like it can go anywhere up until we
initiate semi-auto link training. If we don't have the delay, link
training fails.
I tried to root cause this as best I could, but neither the datasheet
for the panel nor the bridge mention a delay of this magnitude in their
timing requirements. So for now, add the mystery delay until someone
figures out a better fix.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-8-sean@poorly.run
0day reports:
>> drivers/gpu/drm/bridge/ti-sn65dsi86.o: In function
mipi_dsi_detach'
>> drivers/gpu/drm/bridge/ti-sn65dsi86.c:630: undefined reference to
ti_sn_bridge_attach':
>> drivers/gpu/drm/bridge/ti-sn65dsi86.c:249: undefined reference to
mipi_dsi_device_register_full'
>> drivers/gpu/drm/bridge/ti-sn65dsi86.c:276: undefined reference to
mipi_dsi_device_unregister'
Quite obviously the driver depends on DRM_MIPI_DSI.
We can not use depends since the driver configuration uses select,
so we'll have to select the missing dependency instead.
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Dylan Reid <dgreid@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180815194923.3258-1-sean@poorly.run
-----BEGIN PGP SIGNATURE-----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=g9rD
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
Instead of just waiting 20ms for training to complete, actually poll the
status to ensure training is finished.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-7-sean@poorly.run
Instead of just waiting and hoping, actually poll for the pll lock to be
acquired. As a bonus, this should be significantly faster than the
sleep.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-6-sean@poorly.run
prepare() is the old-timey way to say pre_enable(). It should be called
before modeset. This fixes an issue where the panel on cheza must have
the regulator always-on/boot-on for it to work.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-5-sean@poorly.run
This was hand-rolled in the first version, and will surely be useful as
we expand the driver to support more varied use cases.
Changes in v2:
- Change subject prefix s/panel/bridge/
- Downgrade warning in poll function to error message
- Fix DP_EDP_CONFIGURATION_SET write value (Sandeep)
- Mask upper 8 bits of msg->address (Sandeep)
- Check aux cmd status for errors after completing the send (Sandeep)
- Remove length check since it's covered in the aux status
- Flip the READ check in transfer to WRITE check + early exit
Changes in v3:
- Added to the set
- Wrapped (x) in WDATA/RDATA #defines
- Replace readx_poll* with regmap_read_poll*
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-4-sean@poorly.run
Order registers by offset and rename bits & masks to match the
datasheet. This makes the driver a bit easier to grok and
cross-reference with the datasheet.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-3-sean@poorly.run
This function name was changed to drm_connector_attach_encoder().
Unfortunately this driver was posted on the list before that change, and
applied after
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge
driver")
Cc: Sandeep Panda <spanda@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730174225.257255-1-seanpaul@chromium.org
Recently drm_mode_connector_attach_encoder changed it's name. The change
was not noticed by bridge author, as a result gcc reports compile error
on next branch.
Fixes: f38b7cca6d ("drm/bridge: tc358764: Add DSI to LVDS bridge driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727094859.27727-1-a.hajda@samsung.com
Add support for TI's sn65dsi86 dsi2edp bridge chip.
The chip converts DSI transmitted signal to eDP signal,
which is fed to the connected eDP panel.
This chip can be controlled via either i2c interface or
dsi interface. Currently in driver all the control registers
are being accessed through i2c interface only.
Also as of now HPD support has not been added to bridge
chip driver.
Changes in v1:
- Split the dt-bindings and the driver support into separate patches
(Andrzej Hajda).
- Use of gpiod APIs to parse and configure gpios instead of obsolete ones
(Andrzej Hajda).
- Use macros to define the register offsets (Andrzej Hajda).
Changes in v2:
- Separate out edp panel specific HW resource handling from bridge
driver and create a separate edp panel drivers to handle panel
specific mode information and HW resources (Sean Paul).
- Replace pr_* APIs to DRM_* APIs to log error or debug information
(Sean Paul).
- Remove some of the unnecessary structure/variable from driver (Sean
Paul).
- Rename the function and structure prefix "sn65dsi86" to "ti_sn_bridge"
(Sean Paul / Rob Herring).
- Remove most of the hard-coding and modified the bridge init sequence
based on current mode (Sean Paul).
- Remove the existing function to retrieve the EDID data and
implemented this as an i2c_adapter and use drm_get_edid() (Sean Paul).
- Remove the dummy irq handler implementation, will add back the
proper irq handling later (Sean Paul).
- Capture the required enable gpios in a single array based on dt entry
instead of having individual descriptor for each gpio (Sean Paul).
Changes in v3:
- Remove usage of irq_gpio and replace it as "interrupts" property (Rob
Herring).
- Remove the unnecessary header file inclusions (Sean Paul).
- Rearrange the header files in alphabetical order (Sean Paul).
- Use regmap interface to perform i2c transactions.
- Update Copyright/License field and address other review comments
(Jordan Crouse).
Changes in v4:
- Update License/Copyright (Sean Paul).
- Add Kconfig and Makefile changes (Sean Paul).
- Drop i2c gpio handling from this bridge driver, since i2c sda/scl gpios
will be handled by i2c master.
- Update required supplies names.
- Remove unnecessary goto statements (Sean Paul).
- Add mutex lock to power_ctrl API to avoid race conditions (Sean
Paul).
- Add support to parse reference clk frequency from dt(optional).
- Update the bridge chip enable/disable sequence.
Changes in v5:
- Fixed Kbuild test service reported warnings.
Changes in v6:
- Use PM runtime based ref-counting instead of local ref_count mechanism
(Stephen Boyd).
- Clean up some debug logs and indentations (Sean Paul).
- Simplify dp rate calculation (Sean Paul).
- Add support to configure refclk based on input REFCLK pin or DACP/N
pin (Stephen Boyd).
Changes in v7:
- Use static supply entries instead of dynamic allocation (Andrzej
Hajda).
- Defer bridge driver probe if panel is not probed (Andrzej Hajda).
- Update of_graph APIs for correct node reference management. (Andrzej
Hajda).
- Remove local display_mode object (Andrzej Hajda).
- Remove version id check function from driver.
Changes in v8:
- Move dsi register/attach function to bridge driver probe (Andrzej
Hajda).
- Introduce a new helper function to write 16bit words into consecutive
registers (Andrzej Hajda).
- Remove unnecessary macros (Andrzej Hajda).
Changes in v9:
- Remove dsi register/attach from bridge probe, since dsi dev register
completion also waits for any panel or bridge to get added. This creates
deadlock situation when bridge driver calls dsi dev register and
attach before bridge add, in its probe function.
- Fix issues faced during testing of bridge driver on actual HW.
- Remove unnecessary initializations (Stephen Boyd).
- Use local refclk lut size instead of global macro (Sean Paul).
Changes in v10:
- Use refclk to determine if continuous dsi clock is needed or not.
Changes in v11:
- Read DPPLL_SRC register to determine continuous clock instead of
using refclk handle (Stephen Boyd).
Changes in v12:
- Explain in comment as in why dsi dev registration is done in
bridge_attach (Andrzej Hajda).
- Move HPD disable to bridge_pre_enable (Andrzej Hajda).
- Make panel/DDC exclusive until HPD support is added (Andrzej Hajda).
Changes in v13:
- eDP panels report EDID via DP-AUX channel, so remove support for
dedicated DDC line (Andrzej Hajda).
Changes in v14:
- Remove unnecessary drm_panel checks (Andrzej Hajda).
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532069642-21392-1-git-send-email-spanda@codeaurora.org
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
The bridge loses its hw state when the cable is unplugged. If we detect
this case in the hpd handler, reset its state.
Reported-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703165648.120401-1-seanpaul@chromium.org
Current implementation does not guarantee packed pixel modes working
with every dongle. There are some dongles, which require selecting
the output mode explicitly.
Write proper values to registers in packed_pixel mode, based on how it
is done in vendor's code. Select output color space: RGB
(no packed pixel) or YCBCR422 (packed pixel).
This reverts commit e8b92efa62
("drm/bridge/sii8620: fix display of packed pixel modes in MHL2").
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530204243-6370-3-git-send-email-m.purski@samsung.com
Currently AVI infoframe is sent only in MHL3. However, some MHL2 dongles
need AVI infoframe to work correctly in either packed pixel mode or
non-packed pixel mode.
Send AVI infoframe in set_infoframes() in every case. Create an
infoframe using drm_hdmi_infoframe_from_display_mode() instead of
manually filling each infoframe structure's field.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530204243-6370-2-git-send-email-m.purski@samsung.com
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
-----BEGIN PGP SIGNATURE-----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=ngPr
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc2:
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
Currently packed pixel modes in MHL2 can't be displayed. The device
automatically recognizes output format, so setting format other than
RGB causes failure. Fix it by writing proper values to registers.
Tested on MHL1 and MHL2 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516706239-9104-1-git-send-email-m.purski@samsung.com
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
This patch makes RC_CORE to be selected with this driver.
sil_sii8620 driver calls remote controller interfaces directly
so RC_CORE should be enabled mandatorily.
And some boards not using remote controller device don't really
need to know that RC_CORE config should be enabled to use sil_sii8620
driver only for HDMI.
Changelog v2:
- select INPUT because compiling will fail without INPUT.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1527154379-31886-1-git-send-email-inki.dae@samsung.com
MHL bridge is usually connected to TV via MHL dongle. Currently plugging
HDMI cable to dongle is handled improperly.
Fix it by splitting connecting of a dongle and a HDMI cable. The driver
should now handle unplugging a sink from a dongle and plugging a
different sink with new edid.
Tested on MHL1, MHL2 and MHL3 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516705996-8928-1-git-send-email-m.purski@samsung.com
HSIC initialization was taken from the vendor code. HSIC in MHL circuit
is not connected, so it is not possible to test it. Tests prove that
without HSIC the device works well. Therefore it can be removed.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511968368-30884-1-git-send-email-m.purski@samsung.com
The vendor code waits for infoframe to detect video mode set by source.
We do not need to follow this pattern, because video mode information is
provided by drm core. As a result most of the infoframe handling
code can be removed.
Start transmission immediately after detecting stream on HDMI lines
in irq_scdt() function without waiting for infoframe interrupt.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511956130-24482-1-git-send-email-m.purski@samsung.com
Buffer overflow error should not occur, as mode_fixup() callback
filters pixel clock value and it should never exceed 600000. However,
current implementation is not obviously safe and relies on
implementation of mode_fixup().
Make 'i' variable never reach unsafe value in order to avoid buffer
overflow error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: bf1722ca ("drm/bridge/sii8620: rewrite hdmi start sequence")
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511341718-6974-1-git-send-email-m.purski@samsung.com
There is no need to flip reset pin twice. Also delays can be changed to
values present in vendor's code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Maciej Purski <m.purski@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608060457.18357-1-a.hajda@samsung.com
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbFzauAAoJEAx081l5xIa+jzwP/AwfTreH3XBmlLeMO8kwkAMW
AiH1u3KHrlitN1U85x90dC8hVuuV2Kv9pEXQo1me/TAL/QCb9VZYCSf2dHHkkMwD
1UdwxAQW7soBbTRo9k0zuVJpRGSYIiYfqDh3L6KmTC3UF0tUJm53VOWCLG/DNrtn
XhEnGnlCUNbABZMMpavEvlwxPtvaYFlp6M+MmwRPIx32SrPJ3vSaBzxwWxOaFmjU
xiRdK+GpAbCV8yGeCCSkDgEe/TdWGUhZxoC9dLb0H9ex7ip8uZ0W4D+VTHPFrhQX
6nCpqUbp7BQTsbVSd1pAVsAv45scmSgWbKcqfC0NKSVcsHcJZBR0tQOF9OvnGZcf
o1Hv/beTqJ++IcG2rEIwyJTGxAGfZ0YSb0evTC9VcszaYo+b3+G283bdztIjzDeS
0QCTeLHYbZRHPITWVULNpMWy3TkJv32IdFhQfYSnD8/OGQIxLNhh4FFOtHnOmxSF
N8dnzOLKXhXMo/NgOL+UMNnbgLqIyOtEXCPDLuOQJNv/SOp8662m/A0yRjQNR6M2
gsPmR7dxQIwwJMyqrkLDOF411ABZohulquYgwLgG938MRPmTpPWOR72PtpGF4hAW
HLg+3HHBd1N/A1mlJUMAbUn2eMUACZBUIycE9u+U/geRgve/OQnzJH/FKGP2EJ4R
pf6CruEva+6GRR5GVzuM
=twst
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This starts to support NVIDIA volta hardware with nouveau, and adds
amdgpu support for the GPU in the Kabylake-G (the intel + radeon
single package chip), along with some initial Intel icelake enabling.
Summary:
New Drivers:
- v3d - driver for broadcom V3D V3.x+ hardware
- xen-front - XEN PV display frontend
core:
- handle zpos normalization in the core
- stop looking at legacy pointers in atomic paths
- improved scheduler documentation
- improved aspect ratio validation
- aspect ratio support for 64:27 and 256:135
- drop unused control node code.
i915:
- Icelake (ICL) enabling
- GuC/HuC refactoring
- PSR/PSR2 enabling and fixes
- DPLL management refactoring
- DP MST fixes
- NV12 enabling
- HDCP improvements
- GEM/Execlist/reset improvements
- GVT improvements
- stolen memory first 4k fix
amdgpu:
- Vega 20 support
- VEGAM support (Kabylake-G)
- preOS scanout buffer reservation
- power management gfxoff support for raven
- SR-IOV fixes
- Vega10 power profiles and clock voltage control
- scatter/gather display support on CZ/ST
amdkfd:
- GFX9 dGPU support
- userptr memory mapping
nouveau:
- major refactoring for Volta GV100 support
tda998x:
- HDMI i2c CEC support
etnaviv:
- removed unused logging code
- license text cleanups
- MMU handling improvements
- timeout fence fix for 50 days uptime
tegra:
- IOMMU support in gr2d/gr3d drivers
- zpos support
vc4:
- syncobj support
- CTM, plane alpha and async cursor support
analogix_dp:
- HPD and aux chan fixes
sun4i:
- MIPI DSI support
tilcdc:
- clock divider fixes for OMAP-l138 LCDK board
rcar-du:
- R8A77965 support
- dma-buf fences fixes
- hardware indexed crtc/du group handling
- generic zplane property support
atmel-hclcdc:
- generic zplane property support
mediatek:
- use generic video mode function
exynos:
- S5PV210 FIMD variant support
- IPP v2 framework
- more HW overlays support"
* tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm: (1286 commits)
drm/amdgpu: fix 32-bit build warning
drm/exynos: fimc: signedness bug in fimc_setup_clocks()
drm/exynos: scaler: fix static checker warning
drm/amdgpu: Use dev_info() to report amdkfd is not supported for this ASIC
drm/amd/display: Remove use of division operator for long longs
drm/amdgpu: Update GFX info structure to match what vega20 used
drm/amdgpu/pp: remove duplicate assignment
drm/sched: add rcu_barrier after entity fini
drm/amdgpu: move VM BOs on LRU again
drm/amdgpu: consistenly use VM moved flag
drm/amdgpu: kmap PDs/PTs in amdgpu_vm_update_directories
drm/amdgpu: further optimize amdgpu_vm_handle_moved
drm/amdgpu: cleanup amdgpu_vm_validate_pt_bos v2
drm/amdgpu: rework VM state machine lock handling v2
drm/amdgpu: Add runtime VCN PG support
drm/amdgpu: Enable VCN static PG by default on RV
drm/amdgpu: Add VCN static PG support on RV
drm/amdgpu: Enable VCN CG by default on RV
drm/amdgpu: Add static CG control for VCN on RV
drm/exynos: Fix default value for zpos plane property
...
The dw_hdmi_setup_rx_sense exported function should not use struct device
to recover the dw-hdmi context using drvdata, but take struct dw_hdmi
directly like other exported functions.
This caused a regression using Meson DRM on S905X since v4.17-rc1 :
Internal error: Oops: 96000007 [#1] PREEMPT SMP
[...]
CPU: 0 PID: 124 Comm: irq/32-dw_hdmi_ Not tainted 4.17.0-rc7 #2
Hardware name: Libre Technology CC (DT)
[...]
pc : osq_lock+0x54/0x188
lr : __mutex_lock.isra.0+0x74/0x530
[...]
Process irq/32-dw_hdmi_ (pid: 124, stack limit = 0x00000000adf418cb)
Call trace:
osq_lock+0x54/0x188
__mutex_lock_slowpath+0x10/0x18
mutex_lock+0x30/0x38
__dw_hdmi_setup_rx_sense+0x28/0x98
dw_hdmi_setup_rx_sense+0x10/0x18
dw_hdmi_top_thread_irq+0x2c/0x50
irq_thread_fn+0x28/0x68
irq_thread+0x10c/0x1a0
kthread+0x128/0x130
ret_from_fork+0x10/0x18
Code: 34000964 d00050a2 51000484 9135c042 (f864d844)
---[ end trace 945641e1fbbc07da ]---
note: irq/32-dw_hdmi_[124] exited with preempt_count 1
genirq: exiting task "irq/32-dw_hdmi_" (124) is an active IRQ thread (irq 32)
Fixes: eea034af90 ("drm/bridge/synopsys: dw-hdmi: don't clobber drvdata")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1527673438-20643-1-git-send-email-narmstrong@baylibre.com
Maarten Lankhorst