On some hardware it can take some time to add a unit. If
some remove this unit during this process the remove will
fail.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The remote port remains in error state even if the connection
is re-established. A wrong precondition check was performed on
the port status leading to a cancellation of the port reopen.
Remove the pre-req check because it's not required and better
handled within the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ERP thread is performing a task before it is executing the
corresponding down on the semaphore. The response handler of the
just started exchange config should wait for the completion by
performing a down on this semaphore. Since this semaphore is still
positive from the ERP enqueue the handler won't wait and therefore
the exchange config will always fail leaving the adapter in error.
The problem can be solved by performing the down on the semaphore
before starting an ERP task. This is the logically correct order.
Only walk the ERP loop if there is a task to perform.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The nameserver port might be in state online when the adapter is
offlined. On adapter reactivation the nameserver port is not
re-opened due to the PORT_ONLINE status. This results in an
unsuccessful recovery. In forcing the nameserver port status
to offline on all adapter offline events this issue is prevented.
Waiting for the reference count to drop to zero in
zfcp_wka_port_offline is not required, so remove it.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When running the scsi_scan from the zfcp workqueue and the target
device does not respond, the zfcp workqueue can block until the
scsi_scan hits a timeout. Move the work to the scsi host workqueue,
since this one is also used for the scan from the SCSI midlayer.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix problem that zfcp_fsf_exchange_config_data_sync and
zfcp_fsf_exchange_config_data_sync could try to call zfcp_fsf_req_free
with a NULL pointer.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since we're setting the host port type now to FC_PORTTYPE_NPIV
for adapters running in NPIV mode we should allow this port type
for auto-port scanning as well.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Avoid referencing a fsf request after sending it in fcp_fsf_req_send,
it might have already completed and deallocated.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
tape_3590_offline and tape_34xx_offline are removed and tape_generic_offline
is called directly instead.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A ccw command that reads or writes several records at once will
usually transfer more data then fits into one page and needs to
address memory areas using a list of indirect data address words
(idaw). All but the first of these areas must start on a 4KB or 2KB
block boundary (depending on the idaw format).
A check for this restriction was missing and has been added with
this patch.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd driver can automatically online detected dasds, which
especially important for finding the root device. Currently,
it will wait for each online operation to finish individually,
which may take long if many dasds need to be onlined. When using
the new async framework, these onlining operations can run in
parallel and presence of the root device is ensured by the fact
that prepare_namespace() waits for all async threads to finish.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The QDIO ccw devices are started by ccw_device_start so no timeout
can occur for the interrupt handler. Remove the dead code.
In case of an I/O error set the device state to error and wake up
a possibly running qdio_shutdown waiter.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 64ef895798 ("qeth: remove EDDP")
removed the qeth_core_offl.[hc] files, but ended up doing so by just
patching them to zero size, rather than removing them properly.
Actually remove the files.
Reported-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start a new device recognition if someone writes to sysfs online attribute
of a boxed ccw device. The current test will fail, since cu_type != 0
for devices which were recognized before.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Return -EAGAIN on writes to sysfs online attribute if the corresponding
ccw device is in transient state.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a ccw device did not respond in time during internal io, we set it
into boxed state. With this patch we have the following behaviour:
* the ccw driver will get a notification if the device was online and
goes into the boxed state
* if the device was disconnected and got boxed nothing special is to be
done (it will be handled in reprobing later)
* if the device got boxed while initial sensing it will be unregistered
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce ccw_device_schedule_sch_unregister as a wrapper for queuing
ccw_device_call_sch_unregister on the slow_path_wq. This wrapper
will be used in the next patch.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Wake up even on failed device recognition, since this may be triggered
from a user trying to force a device online. With this patch a write
to the online sysfs attribute will not block for ever but return with
-EAGAIN in this case.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (81 commits)
[S390] remove duplicated #includes
[S390] cpumask: use mm_cpumask() wrapper
[S390] cpumask: Use accessors code.
[S390] cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.
[S390] cpumask: remove cpu_coregroup_map
[S390] fix clock comparator save area usage
[S390] Add hwcap flag for the etf3 enhancement facility
[S390] Ensure that ipl panic notifier is called late.
[S390] fix dfp elf hwcap/facility bit detection
[S390] smp: perform initial cpu reset before starting a cpu
[S390] smp: fix memory leak on __cpu_up
[S390] ipl: Improve checking logic and remove switch defaults.
[S390] s390dbf: Remove needless check for NULL pointer.
[S390] s390dbf: Remove redundant initilizations.
[S390] use kzfree()
[S390] BUG to BUG_ON changes
[S390] zfcpdump: Prevent zcore from beeing built as a kernel module.
[S390] Use csum_partial in checksum.h
[S390] cleanup lowcore.h
[S390] eliminate ipl_device from lowcore
...
Use kzfree() instead of memset() + kfree().
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cksm function in system.h is duplicate to csum_partial in checksum.h.
Remove cksm and use csum_partial instead.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Trivial cleanup, list_del(); list_add{,_tail}() is equivalent
to list_move{,_tail}(). Semantic patch for coccinelle can be
found at www.cccmz.de/~snakebyte/list_move_tail.spatch
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is a cleanup of all the messages this driver prints. It uses the
dev_message macros now.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The inbound and outbound handlers are nearly identical if the outbound
handler uses first_to_check as end index instead of last_move. Since both
values are identical at that point the handlers can be merged.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Errors from SIGA instructions are stored in the per queue qdio_error
and reported back when the queue handler is called. That opens a race
when multiple error conditions occur simultanously.
Report SIGA errors immediately in the return value of do_QDIO so the
upper layer can react and SIGA errors no longer interfere with other
errors.
Move the SIGA error handling in qeth from the outbound handler to
qeth_flush_buffers.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
If the qdio module is unloaded the tiqdio tasklet must be terminated
by tasklet_kill. Move the tasklet_kill after the unregistration of
the adapter interrupt so the tiqdio tasklet will not be scheduled
anymore before calling tasklet_kill.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The index value that indicated that the input queue moved was also used to
store the index of the first acknowledged buffer. For non-qebsm only the
newest buffer is acknowledged which may be different from the last move index
so two seperate values are needed to track the input queue.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ACKnowledgement state should be set on the newest SBAL so an
adapter interrupt surpression check needs to scan fewer SBALs.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qdio_cleanup is a wrapper function that should call qdio_shutdown and
qdio_free. qdio_free was not called if an error occured in qdio_shutdown
resulting in a missing free of allocated resources.
Call qdio_free regardless of the return value of qdio_shutdown.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The queue tasklets were stopped with tasklet_disable. Although tasklet_disable
prevents the tasklet from beeing executed it is still possible that a tasklet
is scheduled on a CPU at that point. A following qdio_establish calls
tasklet_init which clears the tasklet count and the tasklet state leading to
the following Oops:
<2>kernel BUG at kernel/softirq.c:392!
<4>illegal operation: 0001 [#1] SMP
<4>Modules linked in: iptable_filter ip_tables x_tables dm_round_robin dm_multipath scsi_dh sg sd_mod crc_t10dif nfs lockd nfs
_acl sunrpc fuse loop dm_mod qeth_l3 ipv6 zfcp qeth scsi_transport_fc qdio scsi_tgt scsi_mod chsc_sch ccwgroup dasd_eckd_mod dasdm
od ext3 mbcache jbd
<4>Supported: Yes
<4>CPU: 0 Not tainted 2.6.27.13-1.1.mz13-default #1
<4>Process blast.LzS_64 (pid: 16445, task: 000000006cc02538, ksp: 000000006cb67998)
<4>Krnl PSW : 0704c00180000000 00000000001399f4 (tasklet_action+0xc8/0x1d4)
<4> R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 EA:3
<4>Krnl GPRS: ffffffff00000030 0000000000000002 0000000000000002 fffffffffffffffe
<4> 000000000013aabe 00000000003b6a18 fffffffffffffffd 0000000000000000
<4> 00000000006705a8 000000007d0914a8 000000007d0914b0 000000007fecfd30
<4> 0000000000000000 00000000003b63e8 000000007fecfd90 000000007fecfd30
<4>Krnl Code: 00000000001399e8: b9200021 cgr %r2,%r1
<4> 00000000001399ec: a7740004 brc 7,1399f4
<4> 00000000001399f0: a7f40001 brc 15,1399f2
<4> >00000000001399f4: c0100027e8ee larl %r1,636bd0
<4> 00000000001399fa: bf1f1008 icm %r1,15,8(%r1)
<4> 00000000001399fe: a7840019 brc 8,139a30
<4> 0000000000139a02: c0300027e8ef larl %r3,636be0
<4> 0000000000139a08: e3c030000004 lg %r12,0(%r3)
<4>Call Trace:
<4>([<0000000000139c12>] tasklet_hi_action+0x112/0x1d4)
<4> [<000000000013aabe>] __do_softirq+0xde/0x1c4
<4> [<000000000010fa2e>] do_softirq+0x96/0xb0
<4> [<000000000013a8d8>] irq_exit+0x70/0xcc
<4> [<000000000010d1d8>] do_extint+0xf0/0x110
<4> [<0000000000113b10>] ext_no_vtime+0x16/0x1a
<4> [<000003e0000a3662>] ext3_dirty_inode+0xe6/0xe8 [ext3]
<4>([<00000000001f6cf2>] __mark_inode_dirty+0x52/0x1d4)
<4> [<000003e0000a44f0>] ext3_ordered_write_end+0x138/0x190 [ext3]
<4> [<000000000018d5ec>] generic_perform_write+0x174/0x230
<4> [<0000000000190144>] generic_file_buffered_write+0xb4/0x194
<4> [<0000000000190864>] __generic_file_aio_write_nolock+0x418/0x454
<4> [<0000000000190ee2>] generic_file_aio_write+0x76/0xe4
<4> [<000003e0000a05c2>] ext3_file_write+0x3e/0xc8 [ext3]
<4> [<00000000001cc2fe>] do_sync_write+0xd6/0x120
<4> [<00000000001ccfc8>] vfs_write+0xac/0x184
<4> [<00000000001cd218>] SyS_write+0x68/0xe0
<4> [<0000000000113402>] sysc_noemu+0x10/0x16
<4> [<0000020000043188>] 0x20000043188
<4>Last Breaking-Event-Address:
<4> [<00000000001399f0>] tasklet_action+0xc4/0x1d4
<6>qdio: 0.0.c61b ZFCP on SC f67 using AI:1 QEBSM:0 PCI:1 TDD:1 SIGA: W AOP
<4> <0>Kernel panic - not syncing: Fatal exception in interrupt
Use tasklet_kill instead of tasklet_disbale. Since tasklet_schedule must not be
called after tasklet_kill use the QDIO_IRQ_STATE_STOPPED to inidicate that a
queue is going down and prevent further tasklet schedules in that case.
Remove superflous tasklet_schedule from input queue setup, at that time
the queues are not ready so the schedule results in a NOP.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the call to qdio_shutdown from qdio_activate since the upper-layer
drivers are responsible to call qdio_shutdown when qdio_activate returns
with an error.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a mutex to protect the tiq_list. Although reading the list is done
using RCU adding and removing elements from the list must still
happen locked since multiple qdio devices may change the list in parallel
otherwise.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Subchannel reprobing can block the kslowcrw workqueue indefinitely
while waiting for device recognition to finish which is also scheduled
to run on kslowcrw. Prevent this deadlock by moving the waiting
portion of subchannel reprobing to the cio workqueue.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove unused subchannel pointer in io_subchannel_recog_done.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix incorrect check for active I/O in interrogate function.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In some situations a rc in __chsc_do_secm will be overwritten
by another one. This shouldn't do harm since todays callers
don't check for _specific_ errors but fix it for the sake of
correctness.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Writing only spaces to /proc/cio_ignore will cause a buffer overflow
since the size_t value i will not become negative and so buf[-1UL] is
accessed. Change the value of i to ssize_t.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a ccw group device unbinding it from its driver should do the
same as a call to ungroup, since this virtual device can not exist
without a driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some sanity checks in the ccw group driver test the output of
container_of macros to be !NULL. Test the input parameters instead.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case the ccw group driver refuses to set a device [on|off]line,
we should transmit the return code to the caller.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
MAX_ISC is a valid isc number, so arrays with an index of isc
need to have a length of MAX_ISC+1
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since some callers rely on for_each_subchannel_staged to not fail,
fall back to brute force scanning using get_subchannel_by_schid in
case of a oom situation.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add barrier to prevent compiler from reloading pointer to irq handler.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The crw_unregister_handler uses xchg + synchronize_sched when
unregistering a crw_handler.
This doesn't protect crw_collect_info to potentially jump to NULL since
it has unlocked code like this:
if (crw_handlers[i])
crw_handlers[i](NULL, NULL, 1);
So add a mutex which protects the crw handler array for changes.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case the ccw driver refuses to set a device offline, we should
transmit the return code to the caller.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use ccw_device_set_notoper() (which also deletes the device
timer and disables the subchannel) instead of simply setting
the state to DEV_STATE_NOT_OPER in the generic not operational
handling code. This prevents unexpected interrupts popping up
for devices that are deemed not operational.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acting upon the assumption that cio_disable_subchannel()
is only called when we really want to disable the subchannel
(a) remove the check for activity (it is already done in
ccw_device_offline(), which is the place where it matters)
(b) collect pending status via tsch() and ignore it (it
can't matter anymore since the subchannel will be disabled).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The common I/O layer may encounter a situation where the
device number of a ccw device has changed or a device
driver doesn't want to keep a formerly disconnected device
becoming operational again. Instead of using device_del()/
device_add() as now, we can just unbind the driver from the
device and rebind it to get the desired effect (rebinding)
with less overhead.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split machine check handler code and move it to cio and kernel code
where it belongs to. No functional change.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ftrace code is currently not reentrant, so we better don't trace
our machine check handler. Machine checks are handled like NMIs on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dead file. Seems to be a leftover from the 2.4->2.5 conversion.
The used and uptodate version of this file is in arch/s390/kernel.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All in sysinfo.c is core kernel code and not driver code. So move it
to arch/s390/kernel. Also includes some small cleanups.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Moved some Messages into s390 debug feature and changed remaining
messages to use the dev_xxx and pr_xxx macros.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To support High Performance FICON, the DASD device driver has to
translate I/O requests into the new transport mode control words (TCW)
instead of the traditional (command mode) CCW requests.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd device driver will now support ECKD devices with more then
65520 cylinders.
In the traditional ECKD adressing scheme each track is addressed
by a 16-bit cylinder and 16-bit head number. The new addressing
scheme makes use of the fact that the actual number of heads is
never larger then 15, so 12 bits of the head number can be redefined
to be part of the cylinder address.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Permission is now granted to the subsystem to format write R0 with:
* an ID = CCHHR, where CC = physical cylinder number,
HH = physical head number, and R = 0
* a key length of zero
* a data length of eight
* a data field containing all zeros
Signed-off-by: Jean-Baptiste Joret <joret@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All of the ioctls are compatible. Just enable them.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide new shutdown action "dump_reipl" for automatic ipl after dump.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
wait_event_timeout just takes the numnber of jiffies to wait as
an argument. That value does not include jiffies itself.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a recovery is started for a qeth device, additional invocations
to change a mac address, to configure a VLAN interface on top, or to
add multicast addresses should wait till recovery is finished,
otherwise recovery might fail.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth: Unregister MAC addresses from device (layer 2) during
recovery cycle. When the device is set online the MAC
addresses are registered again on the device.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performance measurements showed EDDP does not lower CPU costs but increase
them. So we dump out EDDP code from qeth driver.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics counter for software tx checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only way for a sysfs attribute to remove itself (without
deadlock) is to use the sysfs_schedule_callback() interface.
Vegard Nossum discovered that a poorly written sysfs ->store
callback can repeatedly schedule remove callbacks on the same
device over and over, e.g.
$ while true ; do echo 1 > /sys/devices/.../remove ; done
If the 'remove' attribute uses the sysfs_schedule_callback API
and also does not protect itself from concurrent accesses, its
callback handler will be called multiple times, and will
eventually attempt to perform operations on a freed kobject,
leading to many problems.
Instead of requiring all callers of sysfs_schedule_callback to
implement their own synchronization, provide the protection in
the infrastructure.
Now, sysfs_schedule_callback will only allow one scheduled
callback per kobject. On subsequent calls with the same kobject,
return -EAGAIN.
This is a short term fix. The long term fix is to allow sysfs
attributes to remove themselves directly, without any of this
callback hokey pokey.
[cornelia.huck@de.ibm.com: s390 ccwgroup bits]
Reported-by: vegard.nossum@gmail.com
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dpm_list currently relies on the fact that child devices will
be registered after their parents to get a correct suspend
order. Using device_move() however destroys this assumption, as
an already registered device may be moved under a newly registered
one.
This patch adds a new argument to device_move(), allowing callers
to specify how dpm_list should be adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements uevent suppress in kobject and removes it
from struct device, based on the following ideas:
1,Uevent sending should be one attribute of kobject, so suppressing it
in kobject layer is more natural than in device layer. By this way,
we can do it for other objects embedded with kobject.
2,It may save several bytes for each instance of struct device.(On my
omap3(32bit ARM) based box, can save 8bytes per device object)
This patch also introduces dev_set|get_uevent_suppress() helpers to
set and query uevent_suppress attribute in case to help kobject
as private part of struct device in future.
[This version is against the latest driver-core patch set of Greg,please
ignore the last version.]
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes two problems in the claw driver identified by
static code analysis:
o Change in case differentiation of received sense codes
o Use correct data length in claw hard_start_xmit routine
Signed-off-by: Andrew H. Richter <richtera@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Ursula Braun <ursula.braun@de.ibm.com>
This patch fixes problems in the ctcm driver identified by
static code analysis:
o remove an unnecessary always true condition in ctcm_unpack_skb
o remove duplicate assignment in ctc_mpc_alloc_channel
o remove an unnecessary always true condition in ctcmpc_send_sweep_resp
o remove duplicate initialization in ctcmpc_unpack_skb
o shorten if condition in mpc_action_go_inop
o remove INOP event if mpc group is undefined in mpc_action_doxid7
Signed-off-by: Joel A. Fowler <fowlerja@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the receive code should tolerate any incoming garbage, it
should be protected against a potential wraparound when manipulating
length values within incoming data.
block_len is unsigned, so a too large subtraction will cause a
wraparound.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warnings by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lcs hard_start_xmit routine issued return codes other than
defined for this interface. Now lcs returns only either
NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lcs uses low-level kernel_thread implementation.
All drivers should use <linux/kthread.h> API instead.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the fc_host_port_type as FC_PORTTYPE_NPIV when the subchannel
is running in NPIV mode. This allows to see the correct type with
lsscsi -H -t --list
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A scheduled work might still be pending, running while the adapter is
in progress to get dequeued from the system. This can lead to an
invalid pointer dereference (Oops). Once the adpater is set online
again, ensure the nameserver environment is initialized to the
appropriate values again.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ensure the refcounting is correct even if we were not able to
schedule a work. In addition we have to make sure no scheduled
work is pending while we're dequeing the adapter from the
systems environment.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It will not be necessary to set the erp failed status bit
in case a SCSI device is removed by the SCSI mid layer.
In the case a SCSI device is unavailable for a short time
(15 to 20 seconds) a FCP unit will not get on-line again.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use the I/O blocking mechanism in the FC transport class to allow
faster failovers for multipathing:
- Call fc_remote_port_delete early to set the rport to BLOCKED.
- Check the rport status in queuecommand with fc_remote_portchkready
to no longer accept new I/O for this port and fail the I/O with the
appropriate scsi_cmnd result.
- Implement the terminate_rport_io handler to abort all pending I/O
requests
- Return SCSI commands with DID_TRANSPORT_DISRUPTED while erp is
running.
- When updating the remote port status, check for late changes and
update the remote ports status accordingly.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After an error condition resolved a remote storage port was never
re-opened. The incoming RSCN was not processed accordingly due
to a misinterpreted status flag / return value combination.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The usage of the PCI flag to trigger interrupts is optional. Even
without setting the flag, qdio still receives interrupts to continue
working on the queue. Remove the PCI flag from zfcp, it is not
necessary.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current number based id ERP logging is replaced by a string
based tag version. The benefit is an easier location of the code in
question and the removal of the lengthy array referencing the
individual messages.
The string (7 bytes) based version does not use more space since those
bytes were "used" anyway due to the alignment of the structure.
The encoding of the 7 byte string is as follows
[0-1] = filename
[2-5] = task/function
[6] = section
Due to the character of this string (fixed length) a string
termination is not required here.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
An adapter close was always performed whether it was required,
(e.g. in an error scenario) or not (e.g. initial open).
This patch is changing the process in only doing an
adapter close when it is required.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The status read response FSF_STATUS_READ_SUB_ERROR_PORT is not
defined in the specs and therefore not valid.
All occurrences are removed from the code.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Issue ELS ADISC requests from workqueue. This allows the link test
request to be sent when the request queue is full due to I/O load for
other remote ports. It also simplifies request queue locking,
zfcp_fsf_send_fcp_command_task is now the only function that has
interrupts disabled from the caller. This is also a prereq for the FC
passthrough support that issues ELS requests from userspace.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the SCSI midlayer is running error recovery, the low-level error
recovery in zfcp could be running and preventing the SCSI midlayer to
issue error recovery requests. To avoid unnecessary error recovery
escalation, wait for the zfcp erp to finish and retry if necessary.
While reworking the SCSI eh handlers, alsa cleanup the code and
simplify the interface from zfcp_scsi to the fsf layer.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For calls from zfcp erp, scsi_eh and sysfs switch the calls issuing
FSF requests to zfcp_fsf_req_sbal_get to wait for free SBALs.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Only increment the req_id for successfully issued requests. This
avoids some confusion when debugging issued fsf requests.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The lock only needs to protect the softirq context called from qdio
against the userspace context called from sysfs. spin_lock and
spin_lock_bh is enough.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Provide measurement data for the utilisation of the QDIO outbound queue.
The additional value allows to calculate an average queue utilisation
by looking at the deltas per time unit. Needed for capacity planning.
It is up to user space to handle wrap-arounds of the 64 bit value.
The new counter neatly complements the existing counter for queue full
conditions. That is why, both statistics counter have been integrated.
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use the device pointer in zfcp_unit for tracking if we have a
registered SCSI device. With this approach, the flag
ZFCP_STATUS_UNIT_REGISTERED is only redundant and can be removed.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
PORT_PHYS_CLOSING is only set and cleared, but not actually used
for status checking.
PORT_INVALID_WWPN is set when the GID_PN request does not return
a d_id for a remote port, e.g. when a remote port has been
unplugged. For this case, the d_id is zero. In the erp we can
check the d_id and use the normal escalation procedure that gives
up after three retries and remove the special case.
PORT_NO_WWPN is unused: Each port in the remote port list has a
valid wwpn. The WKA ports are now tracked outside the port
list. Remove the PORT_NO_WWPN flag, since this is no longer set
for any port.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The SUGGEST_* flags in the SCSI command result have been out of fashion
for a while and we don't actually use them in the error handling.
Remove the remaining occurrences.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Standby memory detected with the sclp interface gets always registered
with add_memory calls without considering the limitationt that the
"mem=" kernel paramater implies.
So fix this and only register standby memory that is below the specified
limit.
This fixes zfcpdump since it uses "mem=32M". In case there is appr.
2GB standby memory present all of usable memory would be used for the
struct pages needed for standby memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Handle a malformed hardware response which some versions of the
Support Element (SE) may present during SE restart and which otherwise
would result in an endless loop in function sclp_dispatch_evbufs.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In dasd_device_set_timer and dasd_block_set_timer we interpret the
return value of mod_timer in a wrong way. If the timer expires in
the small window between our check of timer_pending and the call to
mod_timer, then the timer will be set, mod_timer returns zero and
we will call add_timer for a timer that is already pending.
As del_timer and mod_timer do all the necessary checking themselves,
we can simplify our code and remove the race a the same time.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
claw printks are converted to dev_xxx and pr_xxx macros.
Signed-off-by: Andy Richter <richtera@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/s390/net/lcs.c: In function 'lcs_new_device':
drivers/s390/net/lcs.c:2179: error: implicit declaration of function 'lcs_set_multicast_list'
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have separate netdev_ops for OSA and HiperSocket/TR.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DEBUG_FS is disabled debugfs_create_file returns -ENODEV instead
of zero. Since the return value is stored and used at shutdown to remove
existing entries an OOPS may be triggered.
Add a check of the debugfs_create_file return value and in case of an error
set the entry to NULL so it will be ignored at shutdown.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the connection between host and storage server is lost, the
dasd device driver usually blocks all I/O on affected devices and
waits for them to reappear. In some setups however it would be
better if the I/O is returned as error so that device can be
recovered by some other means, eg. in a raid or multipath setup.
Signed-off-by: Holger Smolinski <Holger.Smolinski@de.ibm.com>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a DASD device enters or leaves the 'online' state we need to
trigger change events for the respective disk and partitions.
These extra events are needed because when disk and partitions are
first added, udev rules that try to read disk labels or other data
may fail as the disk may not yet be ready.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC drivers/s390/char/tape_block.o
In file included from drivers/s390/char/tape_block.c:24:
drivers/s390/char/tape.h:159: warning: 'struct request' declared inside
parameter list
Adding the dependency of CONFIG_BLOCK to CONFIG_S390_TAPE_BLOCK.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (84 commits)
wimax: fix kernel-doc for debufs_dentry member of struct wimax_dev
net: convert pegasus driver to net_device_ops
bnx2x: Prevent eeprom set when driver is down
net: switch kaweth driver to netdevops
pcnet32: round off carrier watch timer
i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
wimax: testing for rfkill support should also test for CONFIG_RFKILL_MODULE
wimax: fix kconfig interactions with rfkill and input layers
wimax: fix '#ifndef CONFIG_BUG' layout to avoid warning
r6040: bump release number to 0.20
r6040: warn about MAC address being unset
r6040: check PHY status when bringing interface up
r6040: make printks consistent with DRV_NAME
gianfar: Fixup use of BUS_ID_SIZE
mlx4_en: Returning real Max in get_ringparam
mlx4_en: Consider inline packets on completion
netdev: bfin_mac: enable bfin_mac net dev driver for BF51x
qeth: convert to net_device_ops
vlan: add neigh_setup
dm9601: warn on invalid mac address
...
qeth_l2, qeth_l3 convert to net_device_ops.
qeth_l3 remove vlan neigh_setup hack since it does not work any longer
with the new net_device_ops.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (44 commits)
qlge: Fix sparse warnings for tx ring indexes.
qlge: Fix sparse warning regarding rx buffer queues.
qlge: Fix sparse endian warning in ql_hw_csum_setup().
qlge: Fix sparse endian warning for inbound packet control block flags.
qlge: Fix sparse warnings for byte swapping in qlge_ethool.c
myri10ge: print MAC and serial number on probe failure
pkt_sched: cls_u32: Fix locking in u32_change()
iucv: fix cpu hotplug
af_iucv: Free iucv path/socket in path_pending callback
af_iucv: avoid left over IUCV connections from failing connects
af_iucv: New error return codes for connect()
net/ehea: bitops work on unsigned longs
Revert "net: Fix for initial link state in 2.6.28"
tcp: Kill extraneous SPLICE_F_NONBLOCK checks.
tcp: don't mask EOF and socket errors on nonblocking splice receive
dccp: Integrate the TFRC library with DCCP
dccp: Clean up ccid.c after integration of CCID plugins
dccp: Lockless integration of CCID congestion-control plugins
qeth: get rid of extra argument after printk to dev_* conversion
qeth: No large send using EDDP for HiperSockets.
...
drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_setadapter_parms':
drivers/s390/net/qeth_l3_main.c:1049: warning: too many arguments for format
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
The device driver qeth dos not support large send using EDDP for
HiperSockets.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip assist hw command for setting an IP address last unacceptable
long so we can not spin while we waiting for the irq. Since we can
ensure process context for all occurrences of this command we can use
wait.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For z/VM GuestLAN or VSWITCH devices the transport layer is
configured in z/VM. The layer2 attribute of a participating Linux
device has to match the z/VM definition. In case of a mismatch
Linux currently crashes in qeth recovery due to a reference to the
not yet existing net_device.
Solution: add a check for existence of net_device and add a message
pointing to the mismatch of layer definitions in Linux and z/VM.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSA-devices operating in layer3 mode offer adding of the source MAC
address to the QDIO header of inbound packets. The qeth driver can
exploit this functionality to replace FAKELL-entries in the ethernet
header of received packets.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pre z9 machines provide an mcl string in EBCDIC format,
z9 or later provide string in ASCII format.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish the cputime of the idle process where idle is actually using
cpu cycles from the cputime where idle is sleeping on an enabled wait psw.
The former is accounted as system time, the later as idle time.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements config_changed for the s390 virtio transport.
We use the least significant bit of the interrupt parameter field
to decide, if this interrupt should call the virtio virtqueue callback
or the config_changed callback.
This method is compatible with old host and guest code. Old 64 bit guests
will not check the bit and trigger a harmless additional vring_interrupt
call. Old host code will never set this bit, this is also safe.
This patch also takes care of a potential future 31 bit virtio transport
for s390. On 31 bit _LC_PFAULT_INTPARM and __LC_EXT_PARAMS are identical.
We exploit the alignment of the token and fold the change bit into the
lsb of the token itself.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This allows each virtio user to hand in the alignment appropriate to
their virtio_ring structures.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
This doesn't really matter, since s390 pagesize is 4k anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Remove a message that was emitted for a port that could not initially
be opened. This is a rare case when the port discovery hits an
initiator port and only confuses the user with an initator port logged
in the message. Remove the whole special case: The failed "open port"
request triggers required follow-up actions anyway.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add the support to send CT and ELS requests as unchained FSF requests. This is
required for older hardware and was somehow omitted during the cleanup of the
FSF layer. The req_count and resp_count attributes are unused, so remove them
instead of adding a special case for setting them. Also add debug data and a
warning, when the ct request hits a limit.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With the change to the dev_ message macros, the macro to get the busid
is only used in a few places. Remove it and directly get the dev_name
from the device.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The port flag DID_DID indicates whether we know the current id of the
port. This is always set in parallel. Since the id 0 is invalid
(because the port id 0 is invalid) we can remove the DID_DID flag:
d_id of 0 indicates an invalid d_id != 0 is a valid one.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use an array for looking up the mask corresponding to the 2-bit
information instead of the switch/case.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The information from the kernel parameter is only needed during init.
Keep the three pieces (busid, wwpn and lun) local to simplify the
global zfcp_data structures. While at it, also remove the unused
loglevel variable and give the module parameter variable a better
name.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Get rid of this one:
drivers/s390/scsi/zfcp_erp.c: In function 'zfcp_erp_thread':
drivers/s390/scsi/zfcp_erp.c:1400: warning: ignoring return value of
'down_interruptible', declared with attribute warn_unused_result
zfcp_erp_thread is a kernel thread which can't receive any signals.
So introduce a dummy variable and get rid of the warning.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After the latest changes, the list of FCP devices is only used to
lookup the adapter for requests from the actcli tool. Change this to
use the lookup function in the cio layer. Now we can remove the
adapter list and have one place less to use the global config_lock.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When waiting for a request claim the SBAL before waiting. This way,
locking before each check of the free counter is not required and
sparse does not emit warnings for the complicated locking scheme.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Synchronize the registration and de-registration with the SCSI layer
at CCW registration, de-registration. Before we registered with the
SCSI layer on adapter activation. This way the reg and de-reg process
is in balance.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Move the closing parenthesis before the line break.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
Martin Petermann