IT8620E is mostly compatible to IT7828F. Add generic support for it.
IT8620E supports up to 6 fan tachometers and 6 pwm controls.
Support for the 6th tachometer and for the additional pwm controls
are addded in separate patches.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8790E is a super-IO chip with three fan tachometers. It is mostly
compatible to IT8728F, but only supports three fan tachometers
instead of five.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some chips, in7 is always an internal voltage sensor. Introduce
feature flag to reflect this condition to simplify adding support
for new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ITE chips may have 'E', 'F', or both 'E' and 'F' suffixes.
Introduce suffic configuration to the it87_devices structure
to simplify adding new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On chips with newer PWM control, the PWM frequency divider is 256
instead of 128. Since the base PWM frequency remained the same, the actual
PWM frequency is half of what it used to be with the older PWM control
mechanism.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Detection if a pwm channel is supported was wrong on removal,
causing the code to try removing non-existing sysfs attributes.
That didn't matter much because sysfs attribute removal of non-existing
files fails silently, and because the wrong evaluation always returned
false, but should nevertheless be fixed.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current OPAL firmware exposes the different sensors of an IBM Power
system using node names such as :
sensors/amb-temp#1-data
sensors/amb-temp#1-thrs
cooling-fan#1-data
cooling-fan#1-faulted
cooling-fan#1-thrs
cooling-fan#2-data
...
The ibmpowernv driver, when loaded, parses these names to extract the
sensor index and the sensor attribute name. Unfortunately, this scheme
makes it difficult to add sensors with a different layout (specially of
the same type, like temperature) as the sensor index calculated in OPAL
is directly used in the hwmon sysfs interface.
What this patch does is add a independent hwmon index for each sensor.
The increment of the hwmon index (temp, fan, power, etc.) is kept per
sensor type in the sensor_group table. The sensor_data table is used
to store the association of the hwmon and OPAL indexes, as we need to
have the same hwmon index for different attributes of a same sensor.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It simplifies the creation of the hwmon attributes and will help when
support for a new device tree layout is added. The patch also changes
the name of the routine to parse_opal_node_name().
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It simplifies the create_hwmon_attr_name() routine and it clearly isolates
the conversion done between the OPAL node names and hwmon attributes names.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It will help in adding different compatible properties, coming from a
new device tree layout for example.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ambient is too restrictive as there can be other temperature channels :
core, memory, etc.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Auxiliary fan monitoring is not enabled on ASRock Z77 Pro4-M
with BIOS version 2.00 if booted in UEFI Ultra-FastBoot mode.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After a suspend/resume cycle it is not guaranteed that the hardware monitoring
device is still enabled. Ensure that this is the case after resume.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Get rid of #ifdef CONFIG_PM by using SIMPLE_DEV_PM_OPS and declaring suspend
and resume functions with __maybe_unused.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix build error when CONFIG_THERMAL=m and SENSORS_GPIO_FAN=y
by preventing that combination.
Fixes these build errors:
drivers/built-in.o: In function `gpio_fan_remove':
gpio-fan.c:(.text+0x21e97e): undefined reference to `thermal_cooling_device_unregister'
drivers/built-in.o: In function `gpio_fan_probe':
gpio-fan.c:(.text+0x21efbc): undefined reference to `thermal_cooling_device_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix build errors when CONFIG_THERMAL=m and SENSORS_PWM_FAN=y
by restricting SENSORS_PWM_FAN to 'm' when THERMAL=m.
drivers/built-in.o: In function `pwm_fan_remove':
pwm-fan.c:(.text+0x22ba58): undefined reference to `thermal_cooling_device_unregister'
drivers/built-in.o: In function `pwm_fan_probe':
pwm-fan.c:(.text+0x22bebb): undefined reference to `thermal_of_cooling_device_register'
pwm-fan.c:(.text+0x22bf11): undefined reference to `thermal_cdev_update'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Address the following sparse warnings.
drivers/hwmon/pwm-fan.c:176:5: warning:
symbol 'pwm_fan_of_get_cooling_data' was not declared. Should it be static?
drivers/hwmon/pwm-fan.c:176:5: warning:
no previous prototype for 'pwm_fan_of_get_cooling_data'
pwm_fan_of_get_cooling_data is only used in the pwm-fan driver and thus should
be declared static.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow gpio-fan to be used as thermal cooling device for platforms that
use GPIO maps to control fans.
As part of this change, we make the shutdown and remove logic the same
as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PWM FAN device can now be used as a thermal cooling device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch provides code for reading PWM FAN configuration data via
device tree. The pwm-fan can work with full speed when configuration
is not provided. However, errors are propagated when wrong DT bindings
are found.
Additionally the struct pwm_fan_ctx has been extended.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was necessary to decouple code handling writing to sysfs from the one
responsible for setting PWM of the fan.
Due to that, new __set_pwm() method was extracted, which is responsible for
only setting new PWM duty cycle.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some boards, such as the LaCie 2Big Network v2 or 2Big NAS (based on
Marvell Kirkwood SoCs), an I2C fan controller is used but the alarm
signal is wired to a separate GPIO. Unfortunately, the gpio-fan driver
can't be used to handle GPIO alarm alone from DT: an error is returned
if the "gpios" DT property is missing.
This patch allows to use the gpio-fan driver even if the "alarm-gpios"
DT property is defined alone.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bank register has five unused bits. Verify that those bits are zero
to strengthen the detect function.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8603 only supports three fans, so it is not necessary to skip fan4.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8786E is mostly compatible with IT8771 / IT8772.
Parameters determined by testing various combinations.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Lorblanches <zlika_ese@hotmail.com>
[Guenter Roeck: merged from github, addressed review comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Newer chips don't typically support VID inputs or control.
Add a feature flag for VID support to simplify adding support for
new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fans 4-5 are not supported on all chips and revisions. Also, 16-bit fan
counters are always enabled on some chips. Provide feature flags to
simplify adding support for new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On IT8728F, IT8771E, and IT8772E, fans counters are always 16 bit
and don't need to be configured for it.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TS3000GB0 has a new device ID (0x2913). Since IDT's datasheets suggest
that the upper 8 bit of the device ID reflect the chip ID and the lower
8 bit reflect the version number, modify the code to accept all chips
with ID 0x29xx.
Also add support for TS3001 and TSE2004.
Some of the datasheets for older chips are no longer available from
the IDT web site, so replace explicit links in the documentation with
a generic note.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8781F is mostly compatible to IT8782F. Major difference is that it only
supports four instead of six UART channels, and therefore does not share
the uart6 pins.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only difference between the three power_sensor_name_templates is
whether there is a suffix of "", "_lowest" or "_highest". We might as
well pull those into an array and use a literal format string,
allowing gcc to do type checking of the arguments to
sprintf. Incidentially, the same three suffixes are used in the
temp_sensor_name_templates case, so we end up eliminating one static
array.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
[Guenter Roeck: Fixed line length over 80 characters]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By extracting the only part that differs we can allow static checking
of the format string, and possibly save a little .rodata.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
[Guenter Roeck: continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
devm_regmap_init_i2c() can fail, thus add return value checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
mp102_suspend/tmp102_resume under CONFIG_PM_SLEEP to avoid
build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
[groeck: Declare tmp102_dev_pm_ops as static variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The variables diff_input, ext_vref, and vref_mv are only used in the probe
function and therefore don't need to be kept in the device data structure.
Reviewed-and-Tested-by: Robert Rosengren <robert.rosengren@axis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce code size by using regmap to access i2c registers.
Reviewed-and-Tested-by: Robert Rosengren <robert.rosengren@axis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver supports negative high and critical limits, it can return
negative hysteresis values, so there is no good reason to not let the
user write negative hysteresis values.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
data->temp[index] has type s16. Because of C's promotion rules,
(data->temp[index] << 7) >> 7 is exactly the same as
data->temp[index]. The intention was to use bit 8 as a sign bit, so do
that using the existing API.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The comment above (data << 2) >> 2 explains what the intention is: To
use bit 13 of the 14-bit value data as the sign bit. However, this
doesn't work due to C's promotion rules. data has type s16, but data
<< 2 has type int. To get sign extension, that expression would have
to be cast back to an s16 before being shifted (at which point C's
promotion rules would then kick in again and promote the left operand
to int). As it stands, both expressions are no-ops for any value of
data.
Avoid these subtleties by using the existing API for
this. sign_extend32 works equally well for 8 and 16 bit types.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixed the following warnings (reported by cppcheck):
[drivers/hwmon/abx500.c:224]: (warning) %ld in format string (no. 1)
requires 'long' but the argument type is 'unsigned long'.
[drivers/hwmon/abx500.c:233]: (warning) %ld in format string (no. 1)
requires 'long' but the argument type is 'unsigned long'.
[drivers/hwmon/abx500.c:242]: (warning) %ld in format string (no. 1)
requires 'long' but the argument type is 'unsigned long'.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Subtracting an unsigned long from a signed value causes an overflow with large
values. Use clamp_val() to reduce the number range prior to subtracting it
from the temperature limit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Mixed use of long and int caused an integer overflow when writing large limits.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Despite the name, sign_extend32 works just fine for 16 bit variables,
so it is safe to use.
Cc: Martin Kepplinger <martink@posteo.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.
Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DIV_ROUND_CLOSEST() when dealing with the calibration values to make the
calculations less error prone.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck