2.6.26(.x, cannot remember) could handle the microSD card in my Nokia
3109c attached via USB as mass storage, 2.6.27(.x, up to and included
2.6.27.8) cannot. Please find the attached patch which fixes this
regression, and a copy of /proc/bus/usb/devices with my phone plugged in
running with this patch on Frugalware.
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0421 ProdID=0063 Rev= 6.01
S: Manufacturer=Nokia
S: Product=Nokia 3109c
S: SerialNumber=359561013742570
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
From: CSÉCSY László <boobaa@frugalware.org>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for the Nikon D2H camera.
From: Tobias Kunze Briseño <t@fictive.com>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
This fixes Bugzilla #11583.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Tamas Kerecsen <kerecsen@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1168) updates the unusual_devs entry for the Nokia 5300.
According to Jorge Lucangeli Obes <t4m5yn@gmail.com>, some existing
models have a revision number lower than the lower limit of the
current entry.
The patch also moves the entry for the Nokia 5310 to its correct place
in the file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1169) modifies the unusual_devs entry for the Nokia
6300. According to Maciej Gierok <mgierok@gmail.com> and David
McBride <dwm@doc.ic.ac.uk>, the revision limits need to be wider.
This fixes Bugzilla #11768.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Additional sectors were reported by the Nokia 7610 Supernova phone in
usb storage mode. The following patch rectifies the aforementioned
problem.
Signed-off-by: Ricky Wong Yung Fei <evilbladewarrior@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 65934a9 ("Make USB storage depend on SCSI rather than selecting
it [try #6]") the comment at the top of drivers/usb/storage/Kconfig is
incorrect. Adjust it to the current situation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The camera reports an incorrect size and fails to handle PREVENT-ALLOW
MEDIUM REMOVAL commands. The patch marks the camera as an unusual dev
and adds the flags to enable the workarounds for both shortcomings.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is an entry for the unusual_devs.h file to handle a Mio Moov 330 GPS that
stops responding when it is requested to transfer more than 64KB. The patch is
taken against kernel-2.6.27-git3.
Signed-off-by: Frédéric Marchal <frederic.marchal@wowcompany.co
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this patch, we want to do one thing: add more Huawei product IDs into the
USB driver. Then it can support more Huawei data card devices. So to declare
the unusual device for new Huawei data card devices in unusual_devs.h and to
declare more new product IDs in option.c.
To modify the data value and length in the function of
usb_stor_huawei_e220_init in initializers.c That's because based on the USB
standard, while sending SET_FETURE_D to the device, it requires the
corresponding data to be zero, and its sending length also must be zero. In
our old solution, it can be compatible with our WCDMA data card devices, but
can not support our CDMA data card devices. But in this new solution, it can
be compatible with all of our data card devices.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's the patch that implements the fix you suggested to avoid the
I/O errors that I was running into with my new USB enclosure with a
JMicron USB/ATA bridge, while issuing scsi-io USN or other such
queries used by Fedora's mkinitrd.
http://bugzilla.kernel.org/show_bug.cgi?id=9638#c85
/proc/bus/usb/devices:
T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=152d ProdID=2329 Rev= 1.00
S: Manufacturer=JMicron
S: Product=USB to ATA/ATAPI Bridge
S: SerialNumber=DE5088854FFF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
(patch applied and retested on a modified 2.6.27.2-libre.24.rc1.fc10)
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1118) addresses a problem with certain USB mass-storage
devices. These devices sometimes return less data than asked for and
then provide no sense data to explain the problem. Currently
usb-storage leaves it up to the SCSI layer to decide how this should
be handled, and the SCSI layer interprets the lack of sense data to
mean that nothing went wrong. But if we got less data than required
then something definitely _did_ go wrong, and we should say so.
The patch tells the SCSI layer to retry the command when this sort of
thing happens. Retrying may not solve the underlying problem, but
it's better than believing that data was transferred when it wasn't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Nokia 5310 Music Xpress phone reports one too many sectors in
usb-storage mode. This patch resolves that.
Signed-off-by: David Almaroad <dalmaroad@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1136) adds an unusual_devs entry for a version of the
RockChip MP3 player which can't handle the MODE SENSE command used for
write-protect detection.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I had trouble connecting my cell phone as a storage device - so I added
it to the unusual_devs.h list. I had trouble with the bcdDeviceMin and
Max values - so after some experimenting I made it pretty inclusive.
From: Filip Joelsson <filip@blueturtle.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch alters the Sierra Mass Storage patch so that it is non-configurable.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1120) adds an unusual_devs entry for the Nokia 5300.
Maybe once Nokia releases the Symbian code we'll be able to fix all
the problems it has with the USB mass-storage protocol.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Cedric Godin <cedric@belbone.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add razr v3xx US_FL_FIX_CAPACITY flag to unusual_devs.h in usb-storage
This is another Motorola phone that incorrectly reports the sector count
(off by one).
Problem Description: io errors when mounting phone's sd-card via the
phones usb port
Steps to reproduce: mount Motorola Razr v3xx phones sd-card on Linux Desktop
via usb cable. Phones USB port must be in memory card mode.
DEBUG output:
Jul 9 19:32:41 micky kernel: Buffer I/O error on device sdd, logical block 3970048
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Sense Key : Medium Error [current]
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Add. Sense: No additional sense information
Jul 9 19:32:41 micky kernel: end_request: I/O error, dev sdd, sector 3970048
From: Jost Diederichs <jost@qdusa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch upgrades the support for the Sierra Wireless TRU-Install
feature (i.e. zeroCD) to allow for future support of Linux enabled
TRU-Install devices.
By default all devices that do not have a Linux enabled TRU-Install
device (i.e. the device does not have a Linux package on the virtual CD
partition) will be switched into "modem mode." Devices that do contain a
Linux package in the TRU-Install virtual CD will be allowed to enumerate
as a CD-Rom so that either (a) a user can install the packaged software
or (b) a user-space application (e.g. udev) can switch it to modem mode.
This patch does allow for manual override by adding a usb-storage module
parameter 'swi_tru_install' which can force the modem into either mode
regardless of what packages it contains.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1115) adds unusual_devs entries with the IGNORE_RESIDE
flag for the iRiver T10 and the Simple Tech/Datafab CF+SM card
reader. Apparently these devices provide reasonable residue values
for READ and WRITE operations, but not for others like INQUIRY or READ
CAPACITY.
This fixes the iRiver T10 problem reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1119) will help to reduce the clutter of usb-storage's
unusual_devs file by automatically detecting some devices that need
the IGNORE_RESIDUE flag. The idea is that devices should never return
a non-zero residue for an INQUIRY or a READ CAPACITY command unless
they failed to transfer all the requested data. So if one of these
commands transfers a standard amount of data but there is a positive
residue, we know that the residue is bogus and we can set the flag.
This fixes the problems reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb-storage: quirk around v1.11 firmware on Nikon D40
https://bugzilla.redhat.com/show_bug.cgi?id=454028
Just as in earlier firmware versions, we need to perform this
quirk for the latest version too.
Speculatively do the entry for the D80 too, as they seem to
have the same firmware problems historically.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1110) reverts an earlier patch meant to help with
Wireless USB host controllers. These controllers can have bulk
maxpacket values larger than 512, which puts unusual constraints on
the sizes of scatter-gather list elements. However it turns out that
the block layer does not provide the support we need to enforce these
constraints; merely changing the DMA alignment mask doesn't help.
Hence there's no reason to keep the original patch. The Wireless USB
problem will have to be solved a different way.
In addition, there is a reason to get rid of the earlier patch. By
dereferencing a pointer stored in the ep_in array of struct
usb_device, the current code risks an invalid memory access when it
runs concurrently with device removal. The members of that array are
cleared before the driver's disconnect method is called, so it should
not try to use them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch renames the existing usb_reset_device in hub.c to
usb_reset_and_verify_device and renames the existing
usb_reset_composite_device to usb_reset_device. Also the new
usb_reset_and_verify_device does't need to be EXPORTED .
The idea of the patch is that external interface driver
should warn the other interfaces' driver of the same
device before and after reseting the usb device. One interface
driver shoud call _old_ usb_reset_composite_device instead of
_old_ usb_reset_device since it can't assume the device contains
only one interface. The _old_ usb_reset_composite_device
is safe for single interface device also. we rename the two
functions to make the change easily.
This patch is under guideline from Alan Stern.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
From the current implementation of usb_reset_composite_device
function, the iface parameter is no longer useful. This function
doesn't do something special for the iface usb_interface,compared
with other interfaces in the usb_device. So remove the parameter
and fix the related caller.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1092) implements "soft" unbinding for usb-storage. When
the disconnect routine is called, all commands and reset delays are
allowed to complete normally until after scsi_remove_host() returns.
This means that the commands needed for an orderly shutdown will be
sent through to the device.
Unlike before, the driver will now execute every command that it
accepts. Hence there's no need for special code to catch unexecuted
commands and fail them.
The new sequence of events when disconnect runs goes as follows:
If the device is truly unplugged, set the DISCONNECTING
flag so we won't try to access it any more.
If the SCSI-scanning thread hasn't started up yet, prevent
it from doing anything by setting the new DONT_SCAN flag.
Then wake it up and wait for it to terminate.
Remove the SCSI host. This unbinds the upper-level drivers,
doing an orderly shutdown. Commands sent to quiesce the
device will be transmitted normally, unless the device is
unplugged.
Set the DISCONNECTING flag so that we won't accept any new
commands that might get submitted (there aren't supposed to be
any) and we won't try to access the device for resets.
Tell the control thread to exit by waking it up with no
pending command, and wait for it to terminate.
Go on to do all the other normal stuff: releasing resources,
freeing memory, and so on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1090) converts the one remaining semaphore in
usb-storage into a completion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1089) separates out the dynamic atomic bitflags and the
static bitfields in usb-storage. Until now the two sorts of flags
have been sharing the same word; this has always been awkward.
To help prevent possible confusion, the two new fields each have a
different name from the original. us->fflags contains the fixed
bitfields (mostly taken from the USB ID table in unusual_devs.h), and
us->dflags contains the dynamic atomic bitflags (used with set_bit,
test_bit, and so on).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for rev 2 of an existing unusual_devs entry
enabling ROKR W5s to work. Greg, please apply.
From: Javier Smaldone <javier@smaldone.com.ar>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that the unusual_devs entry for the Motorola M600i needs
another flag. This patch adds it. Thanks to Atte André Jensen
<atte@ballbreaker.dk>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1101) updates the unusual_devs entry for the Cypress
ATACB pass-through. The protocol field is changed from US_PR_BULK to
US_PR_DEVICE, since the Cypress devices already set bInterfaceProtocol
to Bulk-only.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes ordering problems with entries in unusual_devs.h.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch allows to bypass the ZeroCD mechanism for the ET502HS
HDSPA modem, so that it can be mounted as a network device.
Signed-off-by: Mauro Andreolini <andreoli@weblab.ing.unimo.it>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic94xx: fix section mismatch
[SCSI] u14-34f: Fix 32bit only problem
[SCSI] dpt_i2o: sysfs code
[SCSI] dpt_i2o: 64 bit support
[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt to dma_alloc_coherent
[SCSI] dpt_i2o: use standard __init / __exit code
[SCSI] megaraid_sas: fix suspend/resume sections
[SCSI] aacraid: Add Power Management support
[SCSI] aacraid: Fix jbod operations scan issues
[SCSI] aacraid: Fix warning about macro side-effects
[SCSI] add support for variable length extended commands
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
[SCSI] bsg: add large command support
[SCSI] aacraid: Fix down_interruptible() to check the return value correctly
[SCSI] megaraid_sas; Update the Version and Changelog
[SCSI] ibmvscsi: Handle non SCSI error status
[SCSI] bug fix for free list handling
[SCSI] ipr: Rename ipr's state scsi host attribute to prevent collisions
[SCSI] megaraid_mbox: fix Dell CERC firmware problem
drivers/usb/storage/unusual_devs.h lists the address
linux-usb-devel@lists.sourceforge.net for patches to that file. This
address results in a bounce and a pointer to vger. This patch updates
the address in the header file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
FIX_CAPACITY is all that's needed.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1088) adds an unusual_devs entry for Samsung's YP-U3.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global onetouch_release_input() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB storage is built-in but input subsystem is made modular then
OneTouch button functionality can not be selected.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- struct scsi_cmnd had a 16 bytes command buffer of its own.
This is an unnecessary duplication and copy of request's
cmd. It is probably left overs from the time that scsi_cmnd
could function without a request attached. So clean that up.
- Once above is done, few places, apart from scsi-ml, needed
adjustments due to changing the data type of scsi_cmnd->cmnd.
- Lots of drivers still use MAX_COMMAND_SIZE. So I have left
that #define but equate it to BLK_MAX_CDB. The way I see it
and is reflected in the patch below is.
MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB
as per the SCSI standard and is not related
to the implementation.
BLK_MAX_CDB. - The allocated space at the request level
- I have audit all ISA drivers and made sure none use ->cmnd in a DMA
Operation. Same audit was done by Andi Kleen.
(*)fixed-length here means commands that their size can be determined
by their opcode and the CDB does not carry a length specifier, (unlike
the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly
true and the SCSI standard also defines extended commands and
vendor specific commands that can be bigger than 16 bytes. The kernel
will support these using the same infrastructure used for VARLEN CDB's.
So in effect MAX_COMMAND_SIZE means the maximum size command
scsi-ml supports without specifying a cmd_len by ULD's
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1060) makes usb-storage set the DMA alignment mask for
SCSI slaves to match the maxpacket size of the bulk-IN endpoint,
rather than always setting it to 511. For full-speed devices that
mask is too restrictive, and wireless USB devices can have maxpacket
sizes larger than 512.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since there seems to be little reason to mark the current USB storage
features as "EXPERIMENTAL," remove that dependency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have got a cypress usb-ide bridge and I would like to tune or monitor
my disk with tools like hdparm, hddtemp or smartctl.
My controller support a way to send raw ATA command to the disk with
something call atacb (see
http://download.cypress.com.edgesuite.net/design_resources/datasheets/contents/cy7c68300c_8.pdf).
Atacb support can be added for each application, but there is some disadvantages :
- all application need to be patched
- A race is possible if there other accesses, because the emulation can
be split in 2 atacb scsi transactions. One for sending the command, one
for reading the register (if ck_cond is set).
I have implemented the emulation in usb-storage with a special proto_handler,
and an unsual entry.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Torsten Kaiser pointed out, it seems the dependency of
USB_STORAGE_ONETOUCH on !PM should have been removed in commit
7931e1c6f8.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I converted the usu_init_notify semaphore to normal mutex usage, and it
should still prevent the request_module before the init routine is
complete. Before it acted more like a complete, now the mutex protects two
distinct section from running at the same time.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- declare the unusal device for Huawei data card devices in
unusual_devs.h
- disable the product ID matching for Huawei data card devices in
usb_match_device function of driver.c
- declare the product IDs in option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Motorola ROKR Z6 cellphone has bugs in its USB, so it is impossible to use
it as mass storage. Patch describes new "unusual" USB device for it with
FIX_INQUIRY and FIX_CAPACITY flags and new BULK_IGNORE_TAG flag.
Last flag relaxes check for equality of bcs->Tag and us->tag in
usb_stor_Bulk_transport routine.
Signed-off-by: Constantin Baranov <const@tltsu.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the inquiry fails then the info structure on us->extra was not freed.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] a100u2w: fix bitmap lookup routine
[SCSI] fix media change events for polled devices
[SCSI] sd, sr: do not emit change event at device add
[SCSI] mpt fusion: Power Management fixes for MPT SAS PCI-E controllers
[SCSI] gdth: Allocate sense_buffer to prevent NULL pointer dereference
[SCSI] arcmsr: fix iounmap error for Type B adapter
[SCSI] isd200: Allocate sense_buffer for hacked up scsi_cmnd
[SCSI] fix bsg queue oops with iscsi logout
[SCSI] Fix dependency problems in SCSI drivers
[SCSI] advansys: Fix bug in AdvLoadMicrocode
Since the separation of sense_buffer from scsi_cmnd, Drivers that hack their
own struct scsi_cmnd like here isd200, must also take care of their own
sense_buffer.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/usb/storage/sddr55.c: In function 'sddr55_transport':
drivers/usb/storage/sddr55.c:526: warning: 'deviceID' may be used uninitialized in this function
drivers/usb/storage/sddr55.c:525: warning: 'manufacturerID' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1037) makes a small update to the earlier as1035 patch.
The minimum-length computation shouldn't be done in
usb_stor_access_xfer_buf(), since that routine can be called multiple
times for a single transfer. It should be done in
usb_stor_set_xfer_buf() instead, which gets called only once.
The way it is now isn't really _wrong_, but it isn't really _right_
either. Moving the statement will be an improvement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1035) fixes a bug in usb_stor_access_xfer_buf() (the bug
was originally found by Boaz Harrosh): The routine must not attempt to
write beyond the end of a scatter-gather list or beyond the number of
bytes requested. It also fixes up the formatting of a few comments
and similar whitespace issues.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1033) adds a quirks entry and an unusual_devs entry for
the Actions Semiconductor flash drive. This device has a 64-byte
string descriptor, which it doesn't terminate with a 0-length packet.
Oddly enough, the reporter's logs show that when the device was
plugged in at boot time, it changes its behavior completely -- it uses
a different product ID, product string descriptor, and bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1034) was written by Leonid Petrov, reported by Robert
Spitzenpfeil, and updated by me. It adds an unusual_devs entry with
the IGNORE_RESIDUE flag for the Oracom MP3 player. Together with the
change to the Get-Max-LUN routine in as1032, it makes the player usable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new BCD numbers for Nikon D80 Firmware revision v1.10 to the
unusual_devs.h file.
Signed-off-by: Konstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1032) removes the Clear-Halt calls in
usb_stor_Bulk_max_lun(). Evidently some devices (such as the Oracom
MP3 player) really don't like to receive these requests when their
bulk endpoints aren't halted.
The only reason for adding them originally was to get an ancient
ZIP-100 drive to work. But since this device has only a single LUN,
we don't need to send it a Get-Max-LUN request at all. Adding an
unusual_devs entry for the ZIP-100 with the SINGLE_LUN flag set will
cause this step to be skipped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that commit 3794ade5b2 removed
incorrect dependency on CONFIG_IDE we can fix the driver to not
include <linux/ide.h>:
* add ATA_REG_{ERROR,LCYL,HCYL,STATUS}_OFFSET defines and use them
instead of IDE_{ERROR,LCYL,HCYL,STATUS}_OFFSET from <linux/ide.h>
* remove no longer needed <linux/ide.h> include
* remove incorrect comment added by the last commit:
- isd200.c is not the only user of struct hd_driveid besides IDE
(see drivers/block/xsysace.c and arch/um/drivers/ubd_kern.c)
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add "FIX_CAPACITY" entry for HP Photosmart r707 Camera in "Disk" mode.
Camera will wedge when /lib/udev/vol_id attempts to access the last sector,
EIO gets reported to dmesg, and block device is marked "offline" (it is).
Reproduced vol_id behavior with:
"dd if=/dev/sda of=/dev/null skip=60800 count=1"
Cc: stable <stable@kernel.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In preparation for bidi we abstract all IO members of scsi_cmnd,
that will need to duplicate, into a substructure.
- Group all IO members of scsi_cmnd into a scsi_data_buffer
structure.
- Adjust accessors to new members.
- scsi_{alloc,free}_sgtable receive a scsi_data_buffer instead of
scsi_cmnd. And work on it.
- Adjust scsi_init_io() and scsi_release_buffers() for above
change.
- Fix other parts of scsi_lib/scsi.c to members migration. Use
accessors where appropriate.
- fix Documentation about scsi_cmnd in scsi_host.h
- scsi_error.c
* Changed needed members of struct scsi_eh_save.
* Careful considerations in scsi_eh_prep/restore_cmnd.
- sd.c and sr.c
* sd and sr would adjust IO size to align on device's block
size so code needs to change once we move to scsi_data_buff
implementation.
* Convert code to use scsi_for_each_sg
* Use data accessors where appropriate.
- tgt: convert libsrp to use scsi_data_buffer
- isd200: This driver still bangs on scsi_cmnd IO members,
so need changing
[jejb: rebased on top of sg_table patches fixed up conflicts
and used the synergy to eliminate use_sg and sg_count]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch sets the last_sector_bug flag to 1 for all USB disks. This is
needed to makes the cardreader on various HP multifunction printers work.
Since the performance impact is negible we set this flag for all USB disks to
avoid an unusual_devs.h nightmare.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes. I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.
The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev. (basically all inquiries it
issues can now be directly mapped).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- This patch should be commited before:
usb: transport - convert to accessors and !use_sg code path removal
- isd200_action() was still using direct liniar pointers in issuing
commands to the USB transport level. This is no longer supported,
use one-element scatterlist instead.
- Adjustment of command's length in the case of scsi-to-ata translation
is now restored before return to queuecommand, since other wise it can
leak BIOs.
- isd200_action() return Error on unknown requests. Used to print an error
but still try to send garbage cdb.
- convert few places to scsi data accessors.
- Todo: This file will need to be changed when scsi_cmnd changes to
scsi_data_buffer or any other solution.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- This patch depends on:
usb: transport.c use scsi_eh API in REQUEST_SENSE execution
- Use scsi data accessors and remove of !use_sg code path.
- New usb_stor_bulk_srb() for use by drivers
[jejb: updated with corrective fix.
had a bug in residual handling in the new usb_stor_bulk_srb()
function. Found by Gabriel C. in -mm tree.
Tested-by: Gabriel C <nix.or.die@googlemail.com>
]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- functions that received char* but where passed scatterlist* mostly
were changed to receive void*
- Use scsi data accessors and remove of !use_sg code path
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Use scsi data accessors and remove of !use_sg code path
- This patch is dependent on cleanup patch to usb transport.c/h
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Use scsi data accessors and remove of !use_sg code path
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts one change from 67fa10627e
that prevented userspace from seing the "driver disk" lun in a san disk
device. The kernel shouldn't do this, it's up to userspace to handle
this properly, if it somehow wants to filter this away.
Cc: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device cannot handle the smallest previously limited transfer
size (64 blocks) without stalling, limit the device to the amount of
packets that fit in a platform native page.
The lowest possible limit is PAGE_CACHE_SIZE, so if the device is ever
used on a platform that has larger than 8K pages, you lose unless you
can convince the device firmware folks to fix the issue.
Cc: Mathew Dharm <mdharm-scsi@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1018) adds an unusual_devs entry for the JetFlash
TS1GJF2A. This device doesn't like read requests for more than 188
sectors. Setting max_sectors down to 64 is overkill, but at least
it will work without errors.
For the torturous debugging history, see this thread:
http://marc.info/?t=118745764700005&r=1&w=2
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1000) sets the SCSI allow_restart flag for USB disk
devices. In theory this should never hurt, and there definitely are
devices out there (such as the Seagate 250-GB external drive) which
need the flag to be set.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ISD200 driver imports a single trivial routine from the IDE layer and
in doing so creates a mess of dependancies that drag in the entire old
IDE layer. Even more sad - it does this for a routine which is usually
(little endian) a null function!
- Copy the function into ISD200
- Rename it so it doesn't clash with the ide header prototype
- Remove all the depend constraints
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Introduce freezer-friendly wrappers around wait_event_interruptible() and
wait_event_interruptible_timeout(), originally defined in <linux/wait.h>, to
be used in freezable kernel threads. Make some of the freezable kernel
threads use them.
This is necessary for the freezer to stop sending signals to kernel threads,
which is implemented in the next patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DECLARE_MUTEX_LOCKED was used for semaphores used as completions and we've
got rid of them. Well, except for one in libusual that the maintainer
explicitly wants to keep as semaphore. So convert that useage to an
explicit sema_init and kill of DECLARE_MUTEX_LOCKED so that new code is
reminded to use a completion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: "Satyam Sharma" <satyam.sharma@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] USB storage: sg chaining support
Modify usb_stor_access_xfer_buf() to take a pointer to an sg
entry pointer, so we can keep track of that instead of passing
around an integer index (which we can't use when dealing with
multiple scatterlist arrays).
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Not surprisingly the Nikon D40X DSC needs the same quirks as the D40,
but it has a separate ID.
See http://bugs.gentoo.org/show_bug.cgi?id=191431
From: Ortwin Glück <odi@odi.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached is a very small patch (several comment lines) and a one-line
coded change) that allows for USB storage devices that are larger than
2TB.
At the company where I work we need such support, and one of my
co-workers, Jane Liu, pointed out that SCSI low-layer drivers need to
specify what size CDBs they accept. After looking through the code it
became obvious that the current USB Storage code accepted the default of
12-byte CDBs, so I changed it to accept 16-byte CDBs. This allows our
device to work.
Signed-off-by: Richard Sharpe <rsharpe@richardsharpe.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as996) adds an unusual_devs entry for the Nikon DSC D2Xs
camera.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Upgrade the unusual_devs.h file to support the Nikon D200
Signed-off-by: Mike Pagano <mpagano-kernel@mpagano.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as991) updates the unusual_devs entry for the Nokia 6131
phone. As reported by Juan Ignacio Cherrutti, there's new firmware
available but it still has the same old transfer-size limit.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker spotted that we have already oops'ed if "us"
was NULL.
Since "us" can't be NULL in the only caller this patch removes the
NULL check.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Use new scsi_eh_prep/restor_cmnd() for synchronous
REQUEST_SENSE invocation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This reverts commit 8dfe4b1486.
There are a number of issues still remaining in usb-storage autosuspend,
so, to be safe, we need to revert this for now.
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The MP3/MP4/AVI player "Rockchip ROCK MP3" is seen as a USB disk, but fails
if more than 128 sectors (64kB) are sent or requested in a single read or write
command, and disconnects from the USB bus.
Typical kernel log showing the problem is:
usb 3-1: reset high speed USB device using ehci_hcd and address 6
usb 3-1: reset high speed USB device using ehci_hcd and address 6
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
usb 3-1: USB disconnect, address 6
This patch works around the device limitation by adding "Rockchip ROCK MP3"
to unusual USB devices list and limiting data transfers to 64 sectors (32kB)
per command.
Tested on 2.6.23-rc5 (amd64).
Signed-off-by: Massimiliano Ghilardi <massimiliano.ghilardi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The D40 needs the same quirks as the other (semi-)professional Nikon cameras.
The patch is against 2.6.23-rc5.
Details:
http://bugs.gentoo.org/show_bug.cgi?id=191431
From: Ortwin Glück <odi@odi.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Upgrade the unusual_devs.h file to support the new 1.01 firmware for the Nikon D80.
Signed-off-by: Mike Pagano <mpagano-kernel@mpagano.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as961) fixes a couple of bugs in the disconnect pathway of
usb-storage.
The first problem, which apparently has been around for a while
although nobody noticed it, shows up when an aborted command is still
pending when a disconnect occurs. The SCSI error-handler will
continue to wait in command_abort() until the us->notify completion is
signalled. Thus quiesce_and_remove_host() needs to signal it.
The second problem was introduced recently along with autosuspend
support. Since usb_stor_scan_thread() now calls
usb_autopm_put_interface() before exiting, we can't simply leave the
scanning thread running after a disconnect; we must wait until the
thread exits. This is solved by adding a new struct completion to the
private data structure. Fortuitously, it allows the removal of the
rather clunky mechanism used in the past to insure that all threads
have finished before the module is unloaded.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackberry Pearl can run in two modes; a usb-storage only mode
and a mode that allows access via mass storage and to its database.
The berry_charge module will set the device to dual mode and thus we
should ignore its native mode if that module is built
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as938) adds an unusual_devs entry for the Nikon DSC D100.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds compatibility with Sierra Wireless' new TRU-Install
feature. Future devices that use this feature will not work unless this
patch has been applied.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as930) implements autosuspend for usb-storage. It is
adapted from a patch by Oliver Neukum. Autosuspend is allowed except
during LUN scanning, resets, and command execution.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Following patch removes trailing whitespaces at the ends of lines and converts
smarttabs/whitespaces into real tabs.
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as923) makes usb-storage's control thread use
kthread_should_stop()/kthread_stop(). The scanning thread can't be
similarly converted until the core kthread implementation allows
threads to call do_exit().
The advantage of this change is that we can now be certain the control
thread has terminated before storage_disconnect() returns. This will
simplify the locking requirements when autosuspend support is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as918) introduces a new USB driver method: reset_resume.
It is called when a device needs to be reset as part of a resume
procedure (whether because of a device quirk or because of the
USB-Persist facility), thereby taking over a role formerly assigned to
the post_reset method. As a consequence, post_reset no longer needs
an argument indicating whether it is being called as part of a
reset-resume. This separation of functions makes the code clearer.
In addition, the pre_reset and post_reset method return types are
changed; they now must return an error code. The return value is
unused at present, but at some later time we may unbind drivers and
re-probe if they encounter an error during reset handling.
The existing pre_reset and post_reset methods in the usbhid,
usb-storage, and hub drivers are updated to match the new
requirements. For usbhid the post_reset routine is also used for
reset_resume (duplicate method pointers); for the other drivers a new
reset_resume routine is added. The change to hub.c looks bigger than
it really is, because mark_children_for_reset_resume() gets moved down
next to the new hub_reset_resume() routine.
A minor change to usb-storage makes the usb_stor_report_bus_reset()
routine acquire the host lock instead of requiring the caller to hold
it already.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as891b) removes two unnecessary references to
intf->dev.power.power_state from usb-storage, and replaces a reference
to root_hub->dev.power.power_state with a check of hcd->state. This
is in preparation for the removal of dev.power.power_state, which is
already deprecated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UNUSUAL_DEV: Sync up some reported devices from Ubuntu
Various unusual dev entries accumulated from Ubuntu bug reports.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Also, do not access input_dev->private directly, use helpers.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Sitecom WL-117 is another "driverless" ZD1211 device where the virtual
windows driver CD must be ejected before the WLAN device appears.
zd1211rw takes care of the ejecting, but usb-storage must be told not to claim
the device.
From: Matthew Davidson <mj.davidson@gmail.com>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Per the Rui Santos and the hardware manufacturers, this actually inhibits
useful parts of the hardware. The correct way to use this hardware is with the
software at http://www.kanoistika.sk/bobovsky/archiv/umts/ and the manufacturers
are also planning on including Linux drivers/material in future revisions.
CC: Rui Santos <rsantos@grupopie.com>
CC: <johann.wilhelm@student.tugraz.at>
CC: <zihan@huawei.com>
CC: <wanganyu1983@huawei.com>
CC: <dingjianjian@huawei.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone changed the code to kthread and used his style instead of mine.
The problem with the block variables is that they provoke shadowing,
which is actually exactly what has happened in my other tree which
has the class patch.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the Nikon D80 camera will not work without an UNUSUAL_DEV entry embodied
in the attached patch (made against 2.6.20.3). Hope you find it helpful,
or if not, pass it along to someone who does.
From: Emil Larsson <emil@swip.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an unusual_devs entry for the Motorola RAZR 3vi.
From: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an usual_devs entry for the Nokia 6288. Originally from
Andrew with a re-diff by Phil.
From: Andrew Nayenko <relan@bk.ru>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the duplicate supertop entries that made it into the
.21 rc kernels.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replacing use of UTS_RELEASE with utsname()->release avoids that the
usb-storage driver is recompiled each time the kernel version changes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Device will not work as a mass storage device without US_FL_IGNORE_RESIDUE.
I bought this mp3 player that takes SD cards here
http://www.aiptek.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=AX4&Category_Code=MP3&Store_Code=AS
I can provide the errors in dmesg, if necessary, but this flag was
determined as necessary by doing a quick google on the errors that were
shown in dmesg.
Signed-off-by: Dylan Taft <d13f00l@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as846) adds the IGNORE_RESIDUE flag to the unusual_devs
entry for Sony-Ericsson's P990i phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hi, one of my users has two USB hard drives that need the following
patch, otherwise there are I/O errors similar to those here:
http://bugme.osdl.org/show_bug.cgi?id=3223
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the Bulk-Only spec, usb-storage is supposed to use the
_first_ bulk-in and bulk-out endpoints it finds, not the _last_. And
while we're at it, we ought to test the direction of the interrupt
endpoint as well. This patch (as842) makes both changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as835) removes from usb-storage the code which sets all
devices to a SCSI level of at least SCSI-2. The original reasons for
doing this no longer apply, and in fact it prevents certain kinds of
ATA pass-thru commands from being used.
The patch also marks CB and CBI devices that are SCSI-0 (legacy SCSI)
as being single-LUN, since the combined SCSI-over-USB transport
protocol has no way to convey LUN information to these devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves <linux/usb_ch9.h> to <linux/usb/ch9.h> to reduce some of the
clutter of usb header files.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In appendix a patch for the nokia 6233 mobile phone is included.
The patch is against 2.6.20-rc5. It is my first patch. Hopefully it has
the right format. The code makes my nokia 6233 on my computer work.
From: Manuel Osdoba <manuel.osdoba@tu-ilmenau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
American Megatrends did something wrong in their floppy emulator. It breaks
with both kinds of MODE SENSE which our stack sends. Alan and I tried a few
tweaks, and got LUNs sensed right, but US_FL_NO_WP_DETECT is still needed.
I set the firmware bracket to 1.00 exactly, in case AMI or Sun fix it with a
firmware update. Hey, you never know.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch from Pete fixes the 'ejecting problem' on yet another ipod. Please applyt.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This combines patches from Alan Stern and Robert Schedel for two "Super Top"
drives that need the IGNORE_RESIDUE flag but have different vendor IDs.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=7508
When the Nokia E70 Phone is plugged in to the USB port, I get:
end_request: I/O error, dev sda, sector 1824527
sd 0:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 1824535
sd 0:0:0:0: SCSI error: return code = 0x10070000
The fix is to add these lines to drivers/usb/storage/unusual_devs.h:
Cc: <honkkis@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=7508
When the Nokia E70 Phone is plugged in to the USB port, I get:
end_request: I/O error, dev sda, sector 1824527
sd 0:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 1824535
sd 0:0:0:0: SCSI error: return code = 0x10070000
The fix is to add these lines to drivers/usb/storage/unusual_devs.h:
Cc: <honkkis@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prevents the kernel from detecting the virtual cd-drive with the
Windows drivers.
Signed-off-by: Johann Wilhelm <johann.wilhelm@student.tugraz.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_NOIO is an alias of GFP_NOIO with a single instance of use.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The mass storage device from Digitech designed for Flash Cards, as found
on (for example) the GNX4 device has issues with residue, similar to the
bug report at http://kerneltrap.org/node/6297. This patch adds the
faulty storage device to unusual_devs.h, this not only reduces the noise
in dmesg but also increases the transfer speeds by a factor of 7x for me
(89kB/s -> 637kB/s).
T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1210 ProdID=0003 Rev= 1.00
S: Manufacturer=DigiTech HMG
S: Product=DigiTech Mass Storage
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Signed-off-by: Jaco Kroon <jaco@kroon.co.za>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some reason the unusual_devs.h entry for Sony Ericsson P990i had
three identical copies in a wrong place in the file in addition to the
correct entry.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recently this entry's bcd scope was narrowed so as not to falsly apply
to bcd's other than 0x0110. But while it breaks those of a larger bcd,
it is still needed for those of a smaller bcd - so this changes the
lower bcd limit to 0x0000.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The protocol in this entry is needed for some versions of the device but
not others. This adds the NEED_OVERRIDE flag to prevent it complaining
to users who don't need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as803) adds an unusual_devs entry for the Nokia 6234
mobile phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as796) adds an unusual_devs entry for the Nokia 6131, which
doesn't like large transfer sizes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This makes CONFIG_USB_STORAGE depend on CONFIG_SCSI rather than selecting it,
as selecting it makes CONFIG_USB_STORAGE override the dependencies of SCSI,
causing it to turn on even if they aren't all met.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as794) adds an unusual_devs entry for the Nokia E60.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In file included from drivers/usb/storage/usb.c:180:
drivers/usb/storage/unusual_devs.h:221: error: 'US_PR_KARMA' undeclared here (not in a function)
drivers/usb/storage/unusual_devs.h:221: error: 'rio_karma_init' undeclared here (not in a function)
Cc: Keith Bennett <keith@mcs.st-and.ac.uk>
Acked-by: Bob Copeland <me@bobcopeland.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replaced kernel_thread() with kthread_run() since kernel_thread() is
deprecated in drivers/modules.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The UFI specification doesn't permit devices to indicate non-existent
LUNs in the manner prescribed by the SCSI spec. This patch (as773)
sets a special flag so that the SCSI scanner will recognize these
devices and treat them specially.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changeset from Keith Bennett (via Bob Copeland) moves the Karma
initializer to its own file and adds trapping of the START_STOP command to
enable eject of the device.
Signed-off-by: Keith Bennett <keith@mcs.st-and.ac.uk>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a re-diffed version of one originally sent by Jan Mate
<mate@fiit.stuba.sk>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as781) adds an entry to unusual_devs.h for the Lacie DVD+-RW
drive. Apparently its USB interface has requirements similar to the
Genesys Logic interface; it doesn't like data to be sent too soon after
a command.
This fixes Bugzilla #6817.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This entry was sent in by Emmanuel Vasilakis <evas@forthnet.gr>, turned
into a patch by yours truly.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the Kyocera Finecam L3 entry in unusual devices
originally submitted by Michael Krauth <michael.krauth@web.de> and
Alessandro Fracchetti <al.fracchetti@tin.it> given that Gerriet
<ger.haw@gmx.de> finds he doesn't need it and Alessandro confirms it
isn't needed anymore as well.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The existing unusual_devs entry for the UCR-61S2B appears to have too
wide a revision range. It matches at least one device that doesn't
respond to the initialization sequence. Perhaps the sequence needs to
be updated, or perhaps something else can be done. For now, this patch
(as764) restricts the range to include only the revision mentioned in
the original comment.
This resolves (for now!) Bugzilla entry #6950.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as763) adds an unusual_devs entry for the A-VOX WSX-300ER MP3
player.
From: David Kuehling <dvdkhlng@gmx.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is another unusual_devs entry (as760) for another Nokia device,
this time the 3250.
From: Mario Rettig <mariorettig@web.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This entry has been a mystery for some time. I had sent this patch as an
RFC a while ago, and now we've had two reports of this not being needed,
so I'm removing it.
In the event there are reports of breakage, we should revert this patch,
but add a US_FL_NEED_OVERRIDE flag.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new unusual_devs flag for when usb-storage needs to ignore
a device that it would otherwise claim.
We need to ignore the ZyXEL G220F as it is a virtual CDROM drive which
includes the windows driver for this USB-WLAN adapter. After the windows
driver is installed on a windows system, it converts it into a WLAN adapter
(by ejecting the virtual disc).
The virtual CDROM is of no interest to Linux users. The zd1211rw driver will
automatically perform the eject operation, we just need to ensure that
usb-storage does not claim the device.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as749) extends the unusual_devs entry for the Sony DSC-T1 and
T5 to cover the H5 as well.
From: Lars Jacob <jacob.lars@googlemail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as748) adds an unusual_devs entry for the Nokia E61 mobile
phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as745) adds an unusual_devs entry for the Nokia N91, just like
the entry for the N80 added a couple of weeks ago. Apparently Nokia isn't
using very good firmware these days...
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the kernel version to the usb-storage Protocol/SubClass
unneeded message in order to help us troubleshoot such problems.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases
for this that were in scsiglue.c. It also adds the flag to other devices
reported to need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as730) contains an unusual_devs entry for a Samsung MP3
device.
From: Ernis <ernisv@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as725) adds an unusual_devs entry for the Motorola RAZR V3x.
From: Davide Perini <perini.davide@dpsoftware.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My recent patch converting usb-storage to use
usb_reset_composite_device() added a bug, a race between reset and
disconnect. It was necessary to drop the private lock while executing a
reset, and if a disconnect occurs at that time it will cause a crash.
This patch (as722) fixes the problem by explicitly checking for an early
termination after executing each command.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We all failed to notice that Franck's recent update to usb-storage allowed
an URB to complete after its context data was no longer valid. This patch
(as746) makes the driver wait for the URB to complete whenever there's a
timeout.
Although timeouts in usb-storage are relatively uncommon, they do occur.
Without this patch the code in 2.6.18-rc1 will fault within an interrupt
handler, which is not nice at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Usually we don't care much about 'gcc -W' warnings, but some of us do build
kernels that way to look for problems, and then the fewer warnings we have
to wade through the better. Especially when they are very easy and
non-intrusive to clean up. Which is the case for the following warnings
spewed by drivers/usb/storage/usb.h :
drivers/usb/storage/usb.h:163: warning: `inline' is not at beginning of
+declaration
drivers/usb/storage/usb.h:166: warning: `inline' is not at beginning of
+declaration
There's also some precedence for cleaning up these warnings. I've had
a few patches merged in the past that remove exactly this class of
warnings.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Move <linux/usb_input.h> to <linux/usb/input.h> and remove some
redundant includes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch (as720) adding an unusual_devs entry for the Nokia N80
mobile phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CSÉCSY László