This patch adds a drm_bridge driver for the PTN3460 DisplayPort to LVDS
bridge chip.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DRM driver for (virtual) vga cards using the bochs dispi
interface, such as the qemu standard vga (qemu -vga std).
Don't bother supporting anything but 32bpp for now, even
though the virtual hardware is able to do that.
Known issue: mmap(/dev/fb0) doesn't work.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a very simple framework to register and lookup panels. Panel drivers
can initialize a DRM panel and register it with the framework, allowing
them to be retrieved and used by display drivers. Currently only support
for DPMS and obtaining panel modes is provided. However it should be
sufficient to enable a large number of panels. The framework should also
be easily extensible to support more sophisticated kinds of panels such
as DSI.
The framework hasn't been tied into the DRM core, even though it should
be easily possible to do so if that's what we want. In the current
implementation, display drivers can simple make use of it to retrieve a
panel, obtain its modes and control its DPMS mode.
Note that this is currently only tested on systems that boot from a
device tree. No glue code has been written yet for systems that use
platform data, but it should be easy to add.
Signed-off-by: Thierry Reding <treding@nvidia.com>
MIPI DSI bus allows to model DSI hosts and DSI peripherals using the
Linux driver model. DSI hosts are registered by the DSI host drivers.
During registration DSI peripherals will be created from the children
of the DSI host's device tree node. Support for registration from
board-setup code will be added later when needed.
DSI hosts expose operations which can be used by DSI peripheral drivers
to access associated devices.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The biggest part of the changes is the decoupling of the host1x and DRM
drivers followed by the move of Tegra DRM back to drivers/gpu/drm/tegra
from whence it came. There is a lot of cleanup as well, and the drivers
can now be properly unloaded and reloaded.
HDMI support for the Tegra114 SoC was contributed by Mikko Perttunen.
gr2d support was extended to Tegra114 and the gr3d driver that has been
in the works for quite some time finally made it in. All pieces to run
an OpenGL driver on top of an upstream kernel are now available.
Support for syncpoint bases was added by Arto Merilainen. This is useful
for synchronizing between command streams from different engines such as
gr2d and gr3d.
Erik Faye-Lund and Wei Yongjun contributed various small fixes. Thanks!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=qc03
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.13-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.13-rc1
The biggest part of the changes is the decoupling of the host1x and DRM
drivers followed by the move of Tegra DRM back to drivers/gpu/drm/tegra
from whence it came. There is a lot of cleanup as well, and the drivers
can now be properly unloaded and reloaded.
HDMI support for the Tegra114 SoC was contributed by Mikko Perttunen.
gr2d support was extended to Tegra114 and the gr3d driver that has been
in the works for quite some time finally made it in. All pieces to run
an OpenGL driver on top of an upstream kernel are now available.
Support for syncpoint bases was added by Arto Merilainen. This is useful
for synchronizing between command streams from different engines such as
gr2d and gr3d.
Erik Faye-Lund and Wei Yongjun contributed various small fixes. Thanks!
* tag 'drm/for-3.13-rc1' of git://anongit.freedesktop.org/tegra/linux: (45 commits)
drm/tegra: Reserve syncpoint base for gr3d
drm/tegra: Reserve base for gr2d
drm/tegra: Deliver syncpoint base to user space
gpu: host1x: Add syncpoint base support
gpu: host1x: Add 'flags' field to syncpt request
drm/tegra: Disable clock on probe failure
gpu: host1x: Disable clock on probe failure
drm/tegra: Support bottom-up buffer objects
drm/tegra: Add support for tiled buffer objects
drm/tegra: Add 3D support
drm/tegra: Introduce tegra_drm_submit()
drm/tegra: Use symbolic names for gr2d registers
drm/tegra: Start connectors with correct DPMS mode
drm/tegra: hdmi: Enable VDD earlier for hotplug/DDC
drm/tegra: hdmi: Fix build warnings
drm/tegra: hdmi: Detect DVI-only displays
drm/tegra: Add Tegra114 HDMI support
drm/tegra: hdmi: Parameterize based on compatible property
drm/tegra: hdmi: Rename tegra{2,3} to tegra{20,30}
gpu: host1x: Add support for Tegra114
...
- CRC support from Damien and He Shuang. Long term this should allow us to
test an awful lot modesetting corner cases automatically. So for me as
the maintainer this is really big.
- HDMI audio fix from Jani.
- VLV dpll computation code refactoring from Ville.
- Fixups for the gpu booster from last time around (Chris).
- Some cleanups in the context code from Ben.
- More watermark work from Ville (we'll be getting there ...).
- vblank timestamp improvements from Ville.
- CONFIG_FB=n support, including drm core changes to make the fbdev
helpers optional.
- DP link training improvements (Jani).
- mmio vtable from Ben, prep work for future hw.
* tag 'drm-intel-next-2013-10-18' of git://people.freedesktop.org/~danvet/drm-intel: (132 commits)
drm/i915/dp: don't mention eDP bpp clamping if it doesn't affect bpp
drm/i915: remove dead code in ironlake_crtc_mode_set
drm/i915: crc support for hsw
drm/i915: fix CRC debugfs setup
drm/i915: wait one vblank when disabling CRCs
drm/i915: use ->get_vblank_counter for the crc frame counter
drm/i915: wire up CRC interrupt for ilk/snb
drm/i915: add CRC #defines for ilk/snb
drm/i915: extract display_pipe_crc_update
drm/i915: don't Oops in debugfs for I915_FBDEV=n
drm/i915: set HDMI pixel clock in audio configuration
drm/i915: pass mode to ELD write vfuncs
cpufreq: Add dummy cpufreq_cpu_get/put for CONFIG_CPU_FREQ=n
drm/i915: check gem bo size when creating framebuffers
drm/i915: Use unsigned long for obj->user_pin_count
drm/i915: prevent tiling changes on framebuffer backing storage
drm/i915: grab dev->struct_mutex around framebuffer_init
drm/i915: vlv: fix VGA hotplug after modeset
drm: add support for additional stereo 3D modes
drm/i915: preserve dispaly init order on ByT
...
This patch adds support for the pair of LCD controllers on the Marvell
Armada 510 SoCs. This driver supports:
- multiple contiguous scanout buffers for video and graphics
- shm backed cacheable buffer objects for X pixmaps for Vivante GPU
acceleration
- dual lcd0 and lcd1 crt operation
- video overlay on each LCD crt via DRM planes
- page flipping of the main scanout buffers
- DRM prime for buffer export/import
This driver is trivial to extend to other Armada SoCs.
Included in this commit is the core driver with no output support; output
support is platform and encoder driver dependent.
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Boots Just Fine (tm)!
The only glitch seems to be that at least on Fedora the boot splash
gets confused and doesn't display much at all.
And since there's no ugly console flickering anymore in between, the
flicker while switching between X servers (VT support is still enabled)
is even more jarring.
Also, I'm unsure whether we don't need to somehow kick out vgacon, now
that nothing else gets in the way. But stuff seems to work, so I
don't care. Also everything still works as well with VGA_CONSOLE=n
Also the #ifdef mess needs a bit of a cleanup, follow-up patches will
do just that.
To keep the Kconfig tidy, extract all the i915 options into its own
file.
v2:
- Rebase on top of the preliminary hw support option and the
intel_drv.h cleanup.
- Shut up warnings in i915_debugfs.c
v3: Use the right CONFIG variable, spotted by Chon Ming.
Cc: Lee, Chon Ming <chon.ming.lee@intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Need to get my stuff out the door ;-) Highlights:
- pc8+ support from Paulo
- more vma patches from Ben.
- Kconfig option to enable preliminary support by default (Josh
Triplett)
- Optimized cpu cache flush handling and support for write-through caching
of display planes on Iris (Chris)
- rc6 tuning from Stéphane Marchesin for more stability
- VECS seqno wrap/semaphores fix (Ben)
- a pile of smaller cleanups and improvements all over
Note that I've ditched Ben's execbuf vma conversion for 3.12 since not yet
ready. But there's still other vma conversion stuff in here.
* tag 'drm-intel-next-2013-08-23' of git://people.freedesktop.org/~danvet/drm-intel: (62 commits)
drm/i915: Print seqnos as unsigned in debugfs
drm/i915: Fix context size calculation on SNB/IVB/VLV
drm/i915: Use POSTING_READ in lcpll code
drm/i915: enable Package C8+ by default
drm/i915: add i915.pc8_timeout function
drm/i915: add i915_pc8_status debugfs file
drm/i915: allow package C8+ states on Haswell (disabled)
drm/i915: fix SDEIMR assertion when disabling LCPLL
drm/i915: grab force_wake when restoring LCPLL
drm/i915: drop WaMbcDriverBootEnable workaround
drm/i915: Cleaning up the relocate entry function
drm/i915: merge HSW and SNB PM irq handlers
drm/i915: fix how we mask PMIMR when adding work to the queue
drm/i915: don't queue PM events we won't process
drm/i915: don't disable/reenable IVB error interrupts when not needed
drm/i915: add dev_priv->pm_irq_mask
drm/i915: don't update GEN6_PMIMR when it's not needed
drm/i915: wrap GEN6_PMIMR changes
drm/i915: wrap GTIMR changes
drm/i915: add the FCLK case to intel_ddi_get_cdclk_freq
...
The snapdragon chips have multiple different display controllers,
depending on which chip variant/version. (As far as I can tell, current
devices have either MDP3 or MDP4, and upcoming devices have MDSS.) And
then external to the display controller are HDMI, DSI, etc. blocks which
may be shared across devices which have different display controller
blocks.
To more easily add support for different display controller blocks, the
display controller specific bits are split out into a "kms" module,
which provides the kms plane/crtc/encoder objects.
The external HDMI, DSI, etc. blocks are part encoder, and part connector
currently. But I think I will pull in the drm_bridge patches from
chromeos tree, and split them into a bridge+connector, with the
registers that need to be set in modeset handled by the bridge. This
would remove the 'msm_connector' base class. But some things need to be
double checked to make sure I could get the correct ON/OFF sequencing..
This patch adds support for mdp4 crtc (including hw cursor), dtv encoder
(part of MDP4 block), and hdmi.
Signed-off-by: Rob Clark <robdclark@gmail.com>
When building kernels for a preliminary hardware target, having to add a
kernel command-line option can prove inconvenient. Add a Kconfig option
that changes the default of this option to 1.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Pimp the Kconfig help text a bit as suggested by Damien in
his 2nd review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If NO_DMA=y:
drivers/built-in.o: In function `__drm_pci_free':
drivers/gpu/drm/drm_pci.c:112: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `drm_pci_alloc':
drivers/gpu/drm/drm_pci.c:72: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `drm_gem_unmap_dma_buf':
drivers/gpu/drm/drm_prime.c:87: undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `drm_gem_map_dma_buf':
drivers/gpu/drm/drm_prime.c:78: undefined reference to `dma_map_sg'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Having nouveau builtin would still allow ACPI_VIDEO to be used as external module
if some of the deps for acpi_video have not been met, which would result in a linking
failure. Solve this by selecting all dependencies as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The R-Car Display Unit (DU) DRM driver supports both superposition
processors and all eight planes in RGB and YUV formats with alpha
blending.
Only VGA and LVDS encoders and connectors are currently supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
QXL is a paravirtual graphics device used by the Spice virtual desktop
interface.
The drivers uses GEM and TTM to manage memory, the qxl hw fencing however
is quite different than normal TTM expects, we have to keep track of a number
of non-linear fence ids per bo that we need to have released by the hardware.
The releases are freed from a workqueue that wakes up and processes the
release ring.
releases are suballocated from a BO, there are 3 release categories, drawables,
surfaces and cursor cmds. The hw also has 3 rings for commands, cursor and release handling.
The hardware also have a surface id tracking mechnaism and the driver encapsulates it completely inside the kernel, userspace never sees the actual hw surface
ids.
This requires a newer version of the QXL userspace driver, so shouldn't be
enabled until that has been placed into your distro of choice.
Authors: Dave Airlie, Alon Levy
v1.1: fixup some issues in the ioctl interface with padding
v1.2: add module device table
v1.3: fix nomodeset, fbcon leak, dumb bo create, release ring irq,
don't try flush release ring (broken hw), fix -modesetting.
v1.4: fbcon cpu usage reduction + suitable accel flags.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a generic helper to fill in an HDMI AVI infoframe with data
extracted from a DRM display mode.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
A simple DRM/KMS driver for the TI LCD Controller found in various
smaller TI parts (AM33xx, OMAPL138, etc). This driver uses the
CMA helpers. Currently only the TFP410 DVI encoder is supported
(tested with beaglebone + DVI cape). There are also various LCD
displays, for which support can be added (as I get hw to test on),
and an external i2c HDMI encoder found on some boards.
The display controller supports a single CRTC. And the encoder+
connector are split out into sub-devices. Depending on which LCD
or external encoder is actually present, the appropriate output
module(s) will be loaded.
v1: original
v2: fix fb refcnting and few other cleanups
v3: get +/- vsync/hsync from timings rather than panel-info, add
option DT max-bandwidth field so driver doesn't attempt to
pick a display mode with too high memory bandwidth, and other
small cleanups
v4: remove some unneeded stuff from panel-info struct, properly
set high bits for hfp/hsw/hbp for rev 2, add DT bindings docs
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Now that the omapdss interface has been reworked so that omapdrm can use
dispc directly, we have been able to fix the remaining functional kms
issues with omapdrm. And in the mean time the PM sequencing and many
other of that open issues have been solved. So I think it makes sense
to finally move omapdrm out of staging.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move this out of nouveau directory. As we start to add more encoder
slaves used by other drivers, it makes sense to put the Kconfig bits in
one place.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
KMS support is out and stable for a couple of years now and
the userspace code has deprecated or abandoned the old UMS interface.
So make the KMS interface the default and deprecate the UMS interface
in the kernel as well.
v2: rebased on alex/drm-next-3.9-wip
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit adds a KMS driver for the Tegra20 SoC. This includes basic
support for host1x and the two display controllers found on the Tegra20
SoC. Each display controller can drive a separate RGB/LVDS output.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Zhang <markz@nvidia.com>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The SH Mobile LCD controller (LCDC) DRM driver supports the main
graphics plane in RGB and YUV formats, as well as the overlay planes (in
alpha-blending mode only).
Only flat panel outputs using the parallel interface are supported.
Support for SYS panels, HDMI and DSI is currently not implemented.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
This patchset introduces a set of helper function for implementing the KMS
framebuffer layer for drivers which use the DRM GEM CMA helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
[Make DRM_KMS_CMA_HELPER a boolean Kconfig option]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Many embedded drm devices do not have a IOMMU and no dedicated
memory for graphics. These devices use CMA (Contiguous Memory
Allocator) backed graphics memory. This patch provides helper
functions to be able to share the code. The code technically does
not depend on CMA as the backend allocator, the name has been chosen
because CMA makes for a nice, short but still descriptive function
prefix.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
[Make DRM_GEM_CMA_HELPER a boolean Kconfig option]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
In drivers/usb/Kconfig "config USB_ARCH_HAS_HCD" is within "if USB_SUPPORT"
statement.
In drivers/gpu/drm/Kconfig "config DRM_USB" depends on USB_ARCH_HAS_HCD
but selects USB_SUPPORT which leads to the error for udl Kconfig:
$ yes "" | make oldconfig
scripts/kconfig/conf --oldconfig Kconfig
drivers/gpu/drm/udl/Kconfig:1:error: recursive dependency detected!
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:76: symbol USB_ARCH_HAS_HCD depends on USB_SUPPORT
drivers/usb/Kconfig:58: symbol USB_SUPPORT is selected by DRM_USB
drivers/gpu/drm/Kconfig:22: symbol DRM_USB is selected by DRM_UDL
Fix this by changing from select to depends on USB_SUPPORT in
"config DRM_USB".
This is a follow-up fix to df0b344300
in Dave's drm-next GIT branch.
[ v2: Restore old status, but change from select to depends on USB_SUPPORT ]
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
There was some merge conflicts in -next and they weren't so pretty, so
backmerge now to avoid them.
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_modes.c
Fix config warning:
warning: ( ... && DRM_USB) selects USB which has unmet direct dependencies
(USB_SUPPORT && USB_ARCH_HAS_HCD)
and build error:
ERROR: "usb_speed_string" [drivers/usb/core/usbcore.ko] undefined!
by adding the missing dependency on USB_ARCH_HAS_HCD to DRM_UDL and DRM_USB.
This exposes:
drivers/video/Kconfig:36:error: recursive dependency detected!
drivers/video/Kconfig:36: symbol FB is selected by DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:28: symbol DRM_KMS_HELPER is selected by DRM_UDL
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:78: symbol USB_ARCH_HAS_HCD depends on USB_ARCH_HAS_OHCI
drivers/usb/Kconfig:16: symbol USB_ARCH_HAS_OHCI depends on I2C
drivers/i2c/Kconfig:5: symbol I2C is selected by FB_DDC
drivers/video/Kconfig:86: symbol FB_DDC is selected by FB_CYBER2000_DDC
drivers/video/Kconfig:385: symbol FB_CYBER2000_DDC depends on FB_CYBER2000
drivers/video/Kconfig:373: symbol FB_CYBER2000 depends on FB
which is due to drivers/usb/Kconfig:
config USB_ARCH_HAS_OHCI
...
default y if ARCH_PNX4008 && I2C
Fix by dropping I2C from the above dependency; logic is that this is not a
platform dependency but a configuration dependency: the _architecture_ still
supports USB even is I2C is not selected.
This exposes:
drivers/video/Kconfig:36:error: recursive dependency detected!
drivers/video/Kconfig:36: symbol FB is selected by DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:28: symbol DRM_KMS_HELPER is selected by DRM_UDL
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:78: symbol USB_ARCH_HAS_HCD depends on USB_ARCH_HAS_OHCI
drivers/usb/Kconfig:17: symbol USB_ARCH_HAS_OHCI depends on MFD_TC6393XB
drivers/mfd/Kconfig:396: symbol MFD_TC6393XB depends on GPIOLIB
drivers/gpio/Kconfig:35: symbol GPIOLIB is selected by FB_VIA
drivers/video/Kconfig:1560: symbol FB_VIA depends on FB
which can be fixed by having MFD_TC6393XB select GPIOLIB instead of depending on
it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the initial driver for emulated cirrus GPU found in qemu.
This driver only supports the emulated GPU and doesn't attempt
to bind to any real cirrus GPUs.
This driver is intended to be used with xf86-video-modesetting in userspace.
It requires at least version 0.3.0
This follow the same design as ast and mgag200, and is based on work
done by Matthew Garrett previously.
This GPU has no hw cursor, and it can't scanout 32-bpp, only packed 24-bpp.
i.e. it sucks.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a driver for the G200 server engines chips,
it doesn't driver any of the Matrix G series desktop cards.
It will bind to G200 SE A,B, G200EV, G200WB, G200EH and G200ER cards.
Its based on previous work done my Matthew Garrett but remodelled
to follow the same style and flow as the AST server driver. It also
works along the same lines as the AST server driver wrt memory management.
There is no userspace driver planned, xf86-video-modesetting should be used.
It also appears these GPUs have no ARGB hw cursors.
v2: add missing tagfifo reset + G200 SE memory bw setup pieces.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is the initial driver for the Aspeed Technologies chips found in
servers. This driver supports the AST 2000, 2100, 2200, 2150 and 2300. It
doesn't support the AST11xx due to lack of hw to test it on, and them requiring
different codepaths.
This driver is intended to be used with xf86-video-modesetting in userspace.
This driver has a slightly different design than other KMS drivers, but
future server chips will probably share similiar setup. As these GPUs commonly
have low video RAM, it doesn't make sense to put the kms console in VRAM
always. This driver places the kms console into system RAM, and does dirty
updates to a copy in video RAM. When userspace sets a new scanout buffer,
it forcefully evicts the video RAM console, and X can create a framebuffer
that can use all of of video RAM.
This driver uses TTM but in a very simple fashion to control the eviction
to system RAM of the console, and multiple servers.
v2: add s/r support, fix Kconfig.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the basic drm dma-buf interface layer, called PRIME. This
commit doesn't add any driver support, it is simply and agreed upon starting
point so we can work towards merging driver support for the next merge window.
Current drivers with work done are nouveau, i915, udl, exynos and omap.
The main APIs exposed to userspace allow translating a 32-bit object handle
to a file descriptor, and a file descriptor to a 32-bit object handle.
The flags value is currently limited to O_CLOEXEC.
Acknowledgements:
Daniel Vetter: lots of review
Rob Clark: cleaned up lots of the internals and did lifetime review.
v2: rename some functions after Chris preferred a green shed
fix IS_ERR_OR_NULL -> IS_ERR
v3: Fix Ville pointed out using buffer + kmalloc
v4: add locking as per ickle review
v5: allow re-exporting the original dma-buf (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-nouveau-next' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/dp: support version 4.0 of DP table
drm/nve0/disp: nvidia randomly decided to move the dithering method
drm/nve0: initial modesetting support for kepler chipsets
drm/nouveau: add bios connector type for dms59
drm/nouveau: move out of staging drivers
drm/nouveau: bump version to 1.0.0
drm/nvd0/disp: ignore clock set if no pclk
drm/nouveau: oops, increase channel dispc_vma to 4
drm/nouveau: inform userspace of new kernel subchannel requirements
drm/nouveau: remove m2mf creation on userspace channels
drm/nvc0-/disp: reimplement flip completion method as fifo method
drm/nouveau: move fence sequence check to start of loop
drm/nouveau: remove subchannel names from places where it doesn't matter
drm/nouveau/ttm: always do buffer moves on kernel channel
There's really no good reason for us to be in here anymore, we have to
maintain this ABI anyway to avoid angering people.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Broken monitors and/or broken graphic boards may send erroneous or no
EDID data. This also applies to broken KVM devices that are unable to
correctly forward the EDID data of the connected monitor but invent
their own fantasy data.
This patch allows to specify an EDID data set to be used instead of
probing the monitor for it. It contains built-in data sets of frequently
used screen resolutions. In addition, a particular EDID data set may be
provided in the /lib/firmware directory and loaded via the firmware
interface. The name is passed to the kernel as module parameter of the
drm_kms_helper module either when loaded
options drm_kms_helper edid_firmware=edid/1280x1024.bin
or as kernel commandline parameter
drm_kms_helper.edid_firmware=edid/1280x1024.bin
It is also possible to restrict the usage of a specified EDID data set
to a particular connector. This is done by prepending the name of the
connector to the name of the EDID data set using the syntax
edid_firmware=[<connector>:]<edid>
such as, for example,
edid_firmware=DVI-I-1:edid/1920x1080.bin
in which case no other connector will be affected.
The built-in data sets are
Resolution Name
--------------------------------
1024x768 edid/1024x768.bin
1280x1024 edid/1280x1024.bin
1680x1050 edid/1680x1050.bin
1920x1080 edid/1920x1080.bin
They are ignored, if a file with the same name is available in the
/lib/firmware directory.
The built-in EDID data sets are based on standard timings that may not
apply to a particular monitor and even crash it. Ideally, EDID data of
the connected monitor should be used. They may be obtained through the
drm/cardX/cardX-<connector>/edid entry in the /sys/devices PCI directory
of a correctly working graphics adapter.
It is even possible to specify the name of an EDID data set on-the-fly
via the /sys/module interface, e.g.
echo edid/myedid.bin >/sys/module/drm_kms_helper/parameters/edid_firmware
The new screen mode is considered when the related kernel function is
called for the first time after the change. Such calls are made when the
X server is started or when the display settings dialog is opened in an
already running X server.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to satisfy all the various Kconfig options between
USB and DRM, we need to split the USB code out into a separate module
and export symbols to it.
This fixes build problems in -next reported by sfr.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is an initial drm/kms driver for the displaylink devices.
Supports fb_defio,
supports KMS dumb interface
supports 24bpp via conversion to 16bpp, hw can do this better.
supports hot unplug using new drm core features.
On an unplug, it disables connector polling, unplugs connectors
from sysfs, unplugs fbdev layer (using Kay's API), drops all the
USB device URBs, and call the drm core to unplug the device.
This driver is based in large parts on udlfb.c so I've licensed
it under GPLv2.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge in the upstream tree to bring in the mainline fixes.
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/nouveau_sgdma.c
slow-work got killed in commit 181a51f6e0. This means that since v2.6.36
there is no Kconfig symbol SLOW_WORK. Apparently selecting that symbol
is a nop. Drop that select.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also improve a bit on the Kconfig help.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch is a DRM Driver for Samsung SoC Exynos4210 and now enables
only FIMD yet but we will add HDMI support also in the future.
this patch is based on git repository below:
git://people.freedesktop.org/~airlied/linux.git
branch name: drm-next
commit-id: 88ef4e3f4f
you can refer to our working repository below:
http://git.infradead.org/users/kmpark/linux-2.6-samsung
branch name: samsung-drm
We tried to re-use lowlevel codes of the FIMD driver(s3c-fb.c
based on Linux framebuffer) but couldn't so because lowlevel codes
of s3c-fb.c are included internally and so FIMD module of this driver has
its own lowlevel codes.
We used GEM framework for buffer management and DMA APIs(dma_alloc_*)
for buffer allocation so we can allocate physically continuous memory
for DMA through it and also we could use CMA later if CMA is applied to
mainline.
Refer to this link for CMA(Continuous Memory Allocator):
http://lkml.org/lkml/2011/7/20/45
this driver supports only physically continuous memory(non-iommu).
Links to previous versions of the patchset:
v1: < https://lwn.net/Articles/454380/ >
v2: < http://www.spinics.net/lists/kernel/msg1224275.html >
v3: < http://www.spinics.net/lists/dri-devel/msg13755.html >
v4: < http://permalink.gmane.org/gmane.comp.video.dri.devel/60439 >
v5: < http://comments.gmane.org/gmane.comp.video.dri.devel/60802 >
Changelog v2:
DRM: add DRM_IOCTL_SAMSUNG_GEM_MMAP ioctl command.
this feature maps user address space to physical memory region
once user application requests DRM_IOCTL_SAMSUNG_GEM_MMAP ioctl.
DRM: code clean and add exception codes.
Changelog v3:
DRM: Support multiple irq.
FIMD and HDMI have their own irq handler but DRM Framework can regiter
only one irq handler this patch supports mutiple irq for Samsung SoC.
DRM: Consider modularization.
each DRM, FIMD could be built as a module.
DRM: Have indenpendent crtc object.
crtc isn't specific to SoC Platform so this patch gets a crtc
to be used as common object.
created crtc could be attached to any encoder object.
DRM: code clean and add exception codes.
Changelog v4:
DRM: remove is_defult from samsung_fb.
is_default isn't used for default framebuffer.
DRM: code refactoring to fimd module.
this patch is be considered with multiple display objects and
would use its own request_irq() to register a irq handler instead of
drm framework's one.
DRM: remove find_samsung_drm_gem_object()
DRM: move kernel private data structures and definitions to driver folder.
samsung_drm.h would contain only public information for userspace
ioctl interface.
DRM: code refactoring to gem modules.
buffer module isn't dependent of gem module anymore.
DRM: fixed security issue.
DRM: remove encoder porinter from specific connector.
samsung connector doesn't need to have generic encoder.
DRM: code clean and add exception codes.
Changelog v5:
DRM: updated fimd(display controller) driver.
added various pixel formats, color key and pixel blending features.
DRM: removed end_buf_off from samsung_drm_overlay structure.
this variable isn't used and end buffer address would be
calculated by each sub driver.
DRM: use generic function for mmap_offset.
replaced samsung_drm_gem_create_mmap_offset() and
samsung_drm_free_mmap_offset() with generic ones applied
to mainline recentrly.
DRM: removed unnecessary codes and added exception codes.
DRM: added comments and code clean.
Changelog v6:
DRM: added default config options.
DRM: added padding for 64-bit align.
DRM: changed prefix 'samsung' to 'exynos'
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Multi-gpu/switcheroo relies on this option to get the console on the
correct GPU at bootup, some distros enable it but it seems some get
it wrong.
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
fix Kconfig warning:
(DRM_I915 && STUB_POULSBO) selects ACPI_VIDEO which has unmet direct dependencies
(ACPI && X86 && BACKLIGHT_CLASS_DEVICE && VIDEO_OUTPUT_CONTROL && INPUT)
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
SMP i810 systems were practically nonexistent and the configuration
was not officially supported by Intel at the time when Pentium-III
was common.
With this change, it is still possible to build a distribution kernel
that has support for SMP and includes the i810 driver without the BKL.
As a precaution, check for the theoretical SMP case at run time and
refuse to load the driver.
We also need to disable CONFIG_PREEMPT builds for this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sean Paul