This removes the handling for PTRACE_CONT et al from the powerpc
ptrace code, so it uses the new generic code via ptrace_request.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This defines the new standard arch_has_single_step macro. It makes the
existing set_single_step and clear_single_step entry points global, and
renames them to the new standard names user_enable_single_step and
user_disable_single_step, respectively.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Commit 5d2efba64b changed our iommu code
so that it always uses an iommu page size of 4kB. That means with our
current code, drivers may do a dma_map_sg() of a 64kB page and obtain
a dma_addr_t that is only 4k aligned.
This works fine in most cases except for some infiniband HW it seems,
where they tell the HW about the page size and it ignores the low bits
of the DMA address.
This works around it by making our IOMMU code enforce a PAGE_SIZE alignment
for mappings of objects that are page aligned in the first place and whose
size is larger or equal to a page.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new network driver fec_mpc52xx will not work on efika because the
firmware does not provide all required properties.
http://www.powerdeveloper.org/asset/by-id/46 has a Forth script to
create more properties. But only the phy stuff is required to get a
working network.
This should go into the kernel because its appearently
impossible to boot the script via tftp and then load the real boot
binary (yaboot or zimage).
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove exports of __res and cpm_install_handler/cpm_free_handler. Remove
cpm_install_handler/cpm_free_handler from the commproc.h as well. Both
were used for ARCH=ppc and aren't defined for ARCH=powerpc.
CC arch/powerpc/kernel/ppc_ksyms.o
arch/powerpc/kernel/ppc_ksyms.c:180: error: '__res' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:180: warning: type defaults to 'int' in declaration of '__res'
make[1]: *** [arch/powerpc/kernel/ppc_ksyms.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
LD .tmp_vmlinux1
arch/powerpc/kernel/built-in.o:(__ksymtab+0x198): undefined reference to `cpm_free_handler'
arch/powerpc/kernel/built-in.o:(__ksymtab+0x1a0): undefined reference to `cpm_install_handler'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The size of swapper_pg_dir is 8k instead of 4k when using 64-bit PTEs
(CONFIG_PTE_64BIT).
This was reported by Cedric Hombourger <chombourger@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The commit fa13a5a1f2 (sched: restore
deterministic CPU accounting on powerpc), unconditionally calls
update_process_tick() in system context. In the deterministic
accounting case this is the correct thing to do. However, in the
non-deterministic accounting case we need to not do this, since doing
this results in the time accounted as hardware irq time being
artificially elevated.
Also this collapses 2 consecutive '#ifdef CONFIG_VIRT_CPU_ACCOUNTING'
checks in time.h into one for neatness.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit a2b51812a4.
It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines. The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called. Until that is clarified I'm reverting this commit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we get no user time and no system time allocated since the last
account_system_vtime, the system to user time ratio estimate can end
up dividing by zero.
This was causing a problem noticed by Balbir Singh.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early. Instead,
call it from the machine_reset() call.
This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().
Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero. Calling os-term
helps keep the hypervisor happy! We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current VDSO implementation is hardcoded to 128 byte cache blocks,
which are only used on IBM's 64-bit processors.
Convert it to get the cache block sizes out of vdso_data instead,
similar to how the ppc64 in-kernel cache flush does it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are several issues with the rtas_ibm_suspend_me code, which
enables platform-assisted suspension of an LPAR as covered in PAPR
2.2.
1.) rtas_ibm_suspend_me uses on_each_cpu() to invoke
rtas_percpu_suspend_me on all cpus via IPI:
if (on_each_cpu(rtas_percpu_suspend_me, &data, 1, 0))
...
'data' is on the calling task's stack, but rtas_ibm_suspend_me takes
no measures to ensure that all instances of rtas_percpu_suspend_me are
finished accessing 'data' before returning. This can result in the
IPI'd cpus accessing random stack data and getting stuck in H_JOIN.
This is addressed by using an atomic count of workers and a completion
on the stack.
2.) rtas_percpu_suspend_me is needlessly calling H_JOIN in a loop.
The only event that can cause a cpu to return from H_JOIN is an H_PROD
from another cpu or a NMI/system reset. Each cpu need call H_JOIN
only once per suspend operation.
Remove the loop and the now unnecessary 'waiting' state variable.
3.) H_JOIN must be called with MSR[EE] off, but lazy interrupt
disabling may cause the caller of rtas_ibm_suspend_me to call H_JOIN
with it on; the local_irq_disable() in on_each_cpu() is not
sufficient.
Fix this by explicitly saving the MSR and clearing the EE bit before
calling H_JOIN.
4.) H_PROD is being called with the Linux logical cpu number as the
parameter, not the platform interrupt server value. (It's also being
called for all possible cpus, which is harmless, but unnecessary.)
This is fixed by calling H_PROD for each online cpu using
get_hard_smp_processor_id(cpu) for the argument.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The early btext debug wouldn't work on PowerMac when booted from BootX
due to the code looking for the wrong property name.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These don't need to be seen by everyone on every boot.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The context switch code in the kernel issues a dummy stwcx. to clear the
reservation, as recommended by the architecture. However, some processors
can have issues if this stwcx to address A occurs while the reservation
is already held to a different address B. To avoid this problem, the dummy
stwcx. needs to be paired with a dummy lwarx to the same address.
This adds the dummy lwarx, and creates a cpu feature bit to indicate
which cpus are affected. Tested on mpc8641_hpcn_defconfig in
arch/powerpc; build tested in arch/ppc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since powerpc started using CONFIG_GENERIC_CLOCKEVENTS, the
deterministic CPU accounting (CONFIG_VIRT_CPU_ACCOUNTING) has been
broken on powerpc, because we end up counting user time twice: once in
timer_interrupt() and once in update_process_times().
This fixes the problem by pulling the code in update_process_times
that updates utime and stime into a separate function called
account_process_tick. If CONFIG_VIRT_CPU_ACCOUNTING is not defined,
there is a version of account_process_tick in kernel/timer.c that
simply accounts a whole tick to either utime or stime as before. If
CONFIG_VIRT_CPU_ACCOUNTING is defined, then arch code gets to
implement account_process_tick.
This also lets us simplify the s390 code a bit; it means that the s390
timer interrupt can now call update_process_times even when
CONFIG_VIRT_CPU_ACCOUNTING is turned on, and can just implement a
suitable account_process_tick().
account_process_tick() now takes the task_struct * as an argument.
Tested both with and without CONFIG_VIRT_CPU_ACCOUNTING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This makes the altivec code in swsusp_32.S depend on CONFIG_ALTIVEC to
avoid build failures for systems that don't have altivec. I'm not sure
whether the code will actually work for other systems, but it was merged
for just ppc32 rather than powermac a very long time ago.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the low level MMU hash table insertion returns an error (which
can happen in some rare circumstances when the hypervisor refuses
the insertion of a PTE, typically if you try to access junk via
/dev/mem), the generated signal had an incorrect si_addr value due
to a bug in the assembly, which was loading it as a 32 bits quantity
instead of a 64 bits quantity.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The size passing to memset is wrong.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An allyesconfig build creates a .text section that is so big that the
.text.init.refok and .fixup sections are too far away for the relocations
to be fixed up correctly. This patch fixes that by linking all the
relevent text sections for each file together.
Suggested by Paul Mackerras.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The decrementer in Book E and 4xx processors interrupts on the
transition from 1 to 0, rather than on the 0 to -1 transition as on
64-bit server and 32-bit "classic" (6xx/7xx/7xxx) processors. At the
moment we subtract 1 from the count of how many decrementer ticks are
required before the next interrupt before putting it into the
decrementer, which is correct for server/classic processors, but could
possibly cause the interrupt to happen too early on Book E and 4xx if
the timebase/decrementer frequency is low.
This fixes the problem by making set_dec subtract 1 from the count for
server and classic processors, instead of having the callers subtract
1. Since set_dec already had a bunch of ifdefs to handle different
processor types, there is no net increase in ugliness. :)
Note that calling set_dec(0) may not generate an interrupt on some
processors. To make sure that decrementer_set_next_event always calls
set_dec with an interval of at least 1 tick, we set min_delta_ns of
the decrementer_clockevent to correspond to 2 ticks (2 rather than 1
to compensate for truncations in the conversions between ticks and
ns).
This also removes a redundant call to set the decrementer to
0x7fffffff - it was already set to that earlier in timer_interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We had an historical confusion in the kernel between cache line
and cache block size. The former is an implementation detail of
the L1 cache which can be useful for performance optimisations,
the later is the actual size on which the cache control
instructions operate, which can be different.
For some reason, we had a weird hack reading the right property
on powermac and the wrong one on any other 64 bits (32 bits is
unaffected as it only uses the cputable for cache block size
infos at this stage).
This fixes the booting-without-of.txt documentation to mention
the right properties, and fixes the 64 bits initialization code
to look for the block size first, with a fallback to the line
size if the property is missing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 44x family has an interesting "feature" which is a virtually
tagged instruction cache (yuck !). So far, we haven't dealt with
it properly, which means we've been mostly lucky or people didn't
report the problems, unless people have been running custom patches
in their distro...
This is an attempt at fixing it properly. I chose to do it by
setting a global flag whenever we change a PTE that was previously
marked executable, and flush the entire instruction cache upon
return to user space when that happens.
This is a bit heavy handed, but it's hard to do more fine grained
flushes as the icbi instruction, on those processor, for some very
strange reasons (since the cache is virtually mapped) still requires
a valid TLB entry for reading in the target address space, which
isn't something I want to deal with.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
On 4xx CPUs, the current implementation of flush_tlb_page() uses
a low level _tlbie() assembly function that only works for the
current PID. Thus, invalidations caused by, for example, a COW
fault triggered by get_user_pages() from a different context will
not work properly, causing among other things, gdb breakpoints
to fail.
This patch adds a "pid" argument to _tlbie() on 4xx processors,
and uses it to flush entries in the right context. FSL BookE
also gets the argument but it seems they don't need it (their
tlbivax form ignores the PID when invalidating according to the
document I have).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
PowerPC 440EP(x) 440GR(x) processors have the same PVR values, since
they have identical cores. However, FPU is not supported on GR(x) and
enabling APU instruction broadcast in the CCR0 register (to enable FPU)
may cause unpredictable results. There's no safe way to detect FPU
support at runtime. This patch provides a workarund for the issue.
We use a POWER6 "logical PVR approach". First, we identify all EP(x)
and GR(x) processors as GR(x) ones (which is safe). Then we check
the device tree cpu path. If we have a EP(x) processor entry,
we call identify_cpu again with PVR | 0x8. This bit is always 0
in the real PVR. This way we enable FPU only for 440EP(x).
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
This patch adapts the ppc64 code to use the generic parse_crashkernel()
function introduced in the generic patch of that series.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the easiest things to isolate is the pid printed in kernel log.
There was a patch, that made this for arch-independent code, this one makes
so for arch/xxx files.
It took some time to cross-compile it, but hopefully these are all the
printks in arch code.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
is_init() is an ambiguous name for the pid==1 check. Split it into
is_global_init() and is_container_init().
A cgroup init has it's tsk->pid == 1.
A global init also has it's tsk->pid == 1 and it's active pid namespace
is the init_pid_ns. But rather than check the active pid namespace,
compare the task structure with 'init_pid_ns.child_reaper', which is
initialized during boot to the /sbin/init process and never changes.
Changelog:
2.6.22-rc4-mm2-pidns1:
- Use 'init_pid_ns.child_reaper' to determine if a given task is the
global init (/sbin/init) process. This would improve performance
and remove dependence on the task_pid().
2.6.21-mm2-pidns2:
- [Sukadev Bhattiprolu] Changed is_container_init() calls in {powerpc,
ppc,avr32}/traps.c for the _exception() call to is_global_init().
This way, we kill only the cgroup if the cgroup's init has a
bug rather than force a kernel panic.
[akpm@linux-foundation.org: fix comment]
[sukadev@us.ibm.com: Use is_global_init() in arch/m32r/mm/fault.c]
[bunk@stusta.de: kernel/pid.c: remove unused exports]
[sukadev@us.ibm.com: Fix capability.c to work with threaded init]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Herbert Poetzel <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds POWERPC specific hooks for scaled time accounting.
POWER6 includes a SPURR register. The SPURR is based off the PURR register
but is scaled based on CPU frequency and issue rates. This gives a more
accurate account of the instructions used per task. The PURR and timebase
will be constant relative to the wall clock, irrespective of the CPU
frequency.
This implementation reads the SPURR register in account_system_vtime which
is only call called on context witch and hard and soft irq entry and exit.
The percentage of user and system time is then estimated using the ratio of
these accounted by the PURR. If the SPURR is not present, the PURR read.
An earlier implementation of this patch read the SPURR whenever the PURR
was read, which included the system call entry and exit path.
Unfortunately this showed a performance regression on lmbench runs, so was
re-implemented.
I've included the lmbench results here when run bare metal on POWER6. 1st
column is the unpatch results. 2nd column is the results using the below
patch and the 3rd is the % diff of these results from the base. 4th and
5th columns are the results and % differnce from the base using the older
patch (SPURR read in syscall entry/exit path).
Base Scaled-Acct SPURR-in-syscall
Result Result % diff Result % diff
Simple syscall: 0.3086 0.3086 0.0000 0.3452 11.8600
Simple read: 0.4591 0.4671 1.7425 0.5044 9.86713
Simple write: 0.4364 0.4366 0.0458 0.4731 8.40971
Simple stat: 2.0055 2.0295 1.1967 2.0669 3.06158
Simple fstat: 0.5962 0.5876 -1.442 0.6368 6.80979
Simple open/close: 3.1283 3.1009 -0.875 3.2088 2.57328
Select on 10 fd's: 0.8554 0.8457 -1.133 0.8667 1.32101
Select on 100 fd's: 3.5292 3.6329 2.9383 3.6664 3.88756
Select on 250 fd's: 7.9097 8.1881 3.5197 8.2242 3.97613
Select on 500 fd's: 15.2659 15.836 3.7357 15.873 3.97814
Select on 10 tcp fd's: 0.9576 0.9416 -1.670 0.9752 1.83792
Select on 100 tcp fd's: 7.248 7.2254 -0.311 7.2685 0.28283
Select on 250 tcp fd's: 17.7742 17.707 -0.375 17.749 -0.1406
Select on 500 tcp fd's: 35.4258 35.25 -0.496 35.286 -0.3929
Signal handler installation: 0.6131 0.6075 -0.913 0.647 5.52927
Signal handler overhead: 2.0919 2.1078 0.7600 2.1831 4.35967
Protection fault: 0.7345 0.7478 1.8107 0.8031 9.33968
Pipe latency: 33.006 16.398 -50.31 33.475 1.42368
AF_UNIX sock stream latency: 14.5093 30.910 113.03 30.715 111.692
Process fork+exit: 219.8 222.8 1.3648 229.37 4.35623
Process fork+execve: 876.14 873.28 -0.32 868.66 -0.8533
Process fork+/bin/sh -c: 2830 2876.5 1.6431 2958 4.52296
File /var/tmp/XXX write bw: 1193497 1195536 0.1708 118657 -0.5799
Pagefaults on /var/tmp/XXX: 3.1272 3.2117 2.7020 3.2521 3.99398
Also, kernel compile times show no difference with this patch applied.
[pbadari@us.ibm.com: Avoid unnecessary PURR reading]
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (24 commits)
[POWERPC] Fix vmemmap warning in init_64.c
[POWERPC] Fix 64 bits vDSO DWARF info for CR register
[POWERPC] Add 1TB workaround for PA6T
[POWERPC] Enable NO_HZ and high res timers for pseries and ppc64 configs
[POWERPC] Quieten cache information at boot
[POWERPC] Quieten clockevent printk
[POWERPC] Enable SLUB in *_defconfig
[POWERPC] Fix 1TB segment detection
[POWERPC] Fix iSeries_hpte_insert prototype
[POWERPC] Fix copyright symbol
[POWERPC] ibmebus: Move to of_device and of_platform_driver, match eHCA and eHEA drivers
[POWERPC] ibmebus: Add device creation and bus probing based on of_device
[POWERPC] ibmebus: Remove bus match/probe/remove functions
[POWERPC] Move of_device allocation into of_device.[ch]
[POWERPC] mpc52xx: device tree changes for FEC and MDIO
[POWERPC] bestcomm: GenBD task support
[POWERPC] bestcomm: FEC task support
[POWERPC] bestcomm: ATA task support
[POWERPC] bestcomm: core bestcomm support for Freescale MPC5200
[POWERPC] mpc52xx: Update mpc52xx_psc structure with B revision changes
...
All asm/ipc.h files do only #include <asm-generic/ipc.h>.
This patch therefore removes all include/asm-*/ipc.h files and moves the
contents of include/asm-generic/ipc.h to include/linux/ipc.h.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes powerpc64's compat code use the new linux/elfcore-compat.h,
reducing some hand-copied duplication.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update dump_task_altivec() (which has so far never been put to use) so that
it dumps the Altivec/VMX registers (VR[0] - VR[31], VSCR and VRSAVE) in the
same format as the ptrace get_vrregs(), and add the appropriate glue
typedef and #defines to make it work.
A new note type of NT_PPC_VMX was chosen to be 0x100 (arbitrarily) because
it allows the low range values to be used for more generic purposes and
0x100 seems an adequate starting point for PowerPC extensions.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current DWARF info for CR are incorrect, causing the gcc unwinder to
go to lunch if we take a segfault in the vdso. This fixes it.
Problem identified by Andrew Haley, and fix provided by Jakub Jelinek
(thanks !).
Unfortunately, a bug in gcc cause it to not quite work either, but that
is being fixed separately with something around the lines of:
linux-unwind.h:
fs->regs.reg[R_CR2].loc.offset = (long) ®s->ccr - new_cfa;
+ /* CR? regs are just 32-bit and PPC is big-endian. */
+ fs->regs.reg[R_CR2].loc.offset += sizeof (long) - 4;
(According to Jakub)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PA6T has a bug where the slbie instruction does not honor the large
segment bit. As a result, we have to always use slbia when switching
context.
We don't have to worry about changing the slbie's during fault processing,
since they should never be replacing one VSID with another using the
same ESID. I.e. there's no risk for inserting duplicate entries due to a
failed slbie of the old entry. So as long as we clear it out on context
switch we should be fine.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After 6 years the ppc64 kernel still thinks its important to tell me my
cache line size is 0x80 bytes. I think most people who care know that by
now. The rest probably cant even understand the hex output.
Since we might have misconfigured firmware or cpus that have a linesize
that isnt 128 bytes, I still print it out for those cases. If people
would prefer to remove it completely, lets do it.
Also for lpar remove the htab_address printout since its not used.
Anton
ppc64 boot log usability expert
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The clockevent bootup message only needs to be KERN_INFO.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace struct ibmebus_dev and struct ibmebus_driver with struct of_device
and struct of_platform_driver, respectively. Match the external ibmebus
interface and drivers using it.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The devtree root is now searched for devices matching a built-in whitelist
during boot, so these devices appear on the bus from the beginning. It is
still possible to manually add/remove devices to/from the bus by using the
probe/remove sysfs interface. Also, when a device driver registers itself,
the devtree is matched against its matchlist.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove old code that will be replaced by rewritten and shorter functions in
the next patch. Keep struct ibmebus_dev and struct ibmebus_driver for now,
but replace ibmebus_{,un}register_driver() by dummy functions. This way, the
kernel will still compile and run during the transition and git bisect will
be happy.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Roland McGrath