Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.
Also, the variable named found is not used well.
This patch targets to optimize and correct this routine. Tested for SPEAr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pl022 ssp controller supports word lengths from 4 to 16 (or 32) bits.
Currently implemented checks were incorrect. It has following check
if (pl022->vendor->max_bpw >= 32)
which must be checking for <=.
Also error print message is incorrect, that prints "range is from 1 to
16".
Fix both these issues.
Signed-off-by: Vinit Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).
Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.
This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does). Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
Mostly a bunch of new drivers and driver bug fixes; but this also
includes a few patches that create a core message queue infrastructure
for the spi subsystem instead of making each driver open code it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6Nsu
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI changes for v3.4 from Grant Likely:
"Mostly a bunch of new drivers and driver bug fixes; but this also
includes a few patches that create a core message queue infrastructure
for the spi subsystem instead of making each driver open code it."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/fsl-espi: Make sure pm is within 2..32
spi/fsl-espi: make the clock computation easier to read
spi: sh-hspi: modify write/read method
spi: sh-hspi: control spi clock more correctly
spi: sh-hspi: convert to using core message queue
spi: s3c64xx: Fix build
spi: s3c64xx: remove unnecessary callback msg->complete
spi: remove redundant variable assignment
spi: release lock on error path in spi_pump_messages()
spi: Compatibility with direction which is used in samsung DMA operation
spi-topcliff-pch: add recovery processing in case wait-event timeout
spi-topcliff-pch: supports a spi mode setup and bit order setup by IO control
spi-topcliff-pch: Fix issue for transmitting over 4KByte
spi-topcliff-pch: Modify pci-bus number dynamically to get DMA device info
spi/imx: simplify error handling to free gpios
spi: Convert to DEFINE_PCI_DEVICE_TABLE
spi: add Broadcom BCM63xx SPI controller driver
SPI: add CSR SiRFprimaII SPI controller driver
spi-topcliff-pch: fix -Wuninitialized warning
spi: Mark spi_register_board_info() __devinit
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This rips the message queue in the PL022 driver out and pushes
it into (optional) common infrastructure. Drivers that want to
use the message pumping thread will need to define the new
per-messags transfer methods and leave the deprecated transfer()
method as NULL.
Most of the design is described in the documentation changes that
are included in this patch.
Since there is a queue that need to be stopped when the system
is suspending/resuming, two new calls are implemented for the
device drivers to call in their suspend()/resume() functions:
spi_master_suspend() and spi_master_resume().
ChangeLog v1->v2:
- Remove Kconfig entry and do not make the queue support optional
at all, instead be more agressive and have it as part of the
compulsory infrastructure.
- If the .transfer() method is implemented, delete print a small
deprecation notice and do not start the transfer pump.
- Fix a bitrotted comment.
ChangeLog v2->v3:
- Fix up a problematic sequence courtesy of Chris Blair.
- Stop rather than destroy the queue on suspend() courtesy of
Chris Blair.
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
WARNING: drivers/spi/built-in.o(.devinit.text+0xdb8): Section mismatch in reference from the function pl022_probe() to the function .init.text:pl022_dma_probe()
The function __devinit pl022_probe() references
a function __init pl022_dma_probe().
If pl022_dma_probe is only used by pl022_probe then
annotate pl022_dma_probe with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This switches the PL022 worker to a kthread in order to get
hold of a mechanism to control the message pump priority. On
low-latency systems elevating the message kthread to realtime
priority give a real sleek response curve. This has been
confirmed by measurements. Realtime priority elevation for
a certain PL022 port can be requested from platform data.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9ugo
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Changes queued in gpio/next for the start of the 3.3 merge window
* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add decode of WM8994 GPIO configuration
gpio: Convert GPIO drivers to module_platform_driver
gpio: Fix typo in comment in Samsung driver
gpio: Explicitly index samsung_gpio_cfgs
gpio: Add Linus Walleij as gpio co-maintainer
of: Add device tree selftests
of: create of_phandle_args to simplify return of phandle parsing data
gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
gpiolib: output basic details and consolidate gpio device drivers
pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
spi/pl022: make the chip deselect handling thread safe
spi/pl022: add support for pm_runtime autosuspend
spi/pl022: disable the PL022 block when unused
spi/pl022: move device disable to workqueue thread
spi/pl022: skip default configuration before suspending
spi/pl022: fix build warnings
spi/pl022: only enable RX interrupts when TX is complete
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
There is a possibility that the pump_message and giveback
run in parallel on a SMP system. Both the pump_message and
giveback threads work on the same SPI message queue.
Results will be in correct if the pump_message gets to
work on the queue first.
when the pump_message works with the queue, it reads the
head of the queue and removes it from the queue. pump_message
activates the chip select depending on this message read.
This leads to giveback working on the modified queue or a
emptied queue. If the queue is empty or if the next message on
the queue (which is not the actual next message, as the pump
message has removed the next message from the queue) is not for
the same SPI device as that Of the previous one, giveback will
de-activate the chip select activated by pump_message(),
which is wrong.
To solve this problem pump_message is made not to run and
access the queue until the giveback is done handling the queue.
I.e. by making the cur_msg NULL after the giveback has read the
queue.
Also a state variable has been introduced to keep track of when
the CS for next message is already activated and avoid to
double-activate it.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for configuring the spi bus to use autosuspend for
runtime power management. This can reduce the latency in starting an
spi transfer by not suspending the device immediately following
completion of a transfer. If another transfer then takes place before
the autosuspend timeout, the call to resume the device can return
immediately rather than needing to risk sleeping in order to resume
the device.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure we clear the enable bit when the block is not used.
This will save some energy in certain hardware versions.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Moves the disabling of the device and clocks to the same thread in
which the device and clocks are enabled. This avoids SMP issues where
the device can be enabled for a transfer by one thread and then
disabled by the completion of the previous transfer in another thread.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The loading of the default configuration before suspending has
been in the driver since its inception, but it is not really
needed. Especially so since we take to all the trouble of
enabling and disabling power and clock just to do this. Let's
scrap this now.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver build complains with newer compilers unless you
initialize this struct properly.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For interrupt mode transfers, start with only TX interrupts enabled
to reduce the overall number of interrupts received. Once TX is
complete, enable RX interrupts to complete the transfer.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Make sure we enable the clock before leaving probe.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves spi, serial drivers to use new enum
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
drivercore: Add helper macro for platform_driver boilerplate
spi: irq: Remove IRQF_DISABLED
OMAP: SPI: Fix the trying to free nonexistent resource error
spi/spi-ep93xx: add module.h include
spi/tegra: fix compilation error in spi-tegra.c
spi: spi-dw: fix all sparse warnings
spi/spi-pl022: Call pl022_dma_remove(pl022) only if enable_dma is true
spi/spi-pl022: calculate_effective_freq() must set rate <= requested rate
spi/spi-pl022: Don't allocate more sg than required.
spi/spi-pl022: Use GFP_ATOMIC for allocation from tasklet
spi/spi-pl022: Resolve formatting issues
This patch fixes a build error, introduced by commit (67fc8b9f, "PM: add
runtime PM support to core Primecell driver") which unfortunately was a little
bit incomplete and did contain a typo (11 instead of 22).
I'm not sure how this patch could have been tested back then, if it
doesn't even compile ;)
The build failure was:
drivers/spi/spi-pl022.c:2292: error: 'adev' undeclared (first use in
this function)
drivers/spi/spi-pl022.c:2344: error: 'pl022_suspend' undeclared here
(not in a function)
The build failure appears e.g. for the u8500 and realview defconfig.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add runtime PM support to the core Primecell driver, following the PCI
model of how this is done.
Rather than having every driver fiddle about with enabling runtime PM,
that's dealt with in the core and instead, drivers just do a put() in
their probe and a balancing get() in their remove function to activate
runtime PM for the device.
As we're dealing with enabling runtime PM in the core, fix up spi-pl022
as it must not enable and disable runtime PM itself anymore.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pl022_dma_remove() should be called only if enable_dma is true. There is no
point calling it when pl022_dma_probe() is not called, which again depends on
enable_dma.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There were few issues with calculate_effective_freq() routine:
- It was returning first rate found >= requested rate. Now, if system have spi's
rate as 83 MHz, with possible prescaled rates as 83, 41.5, 20.75, 13.83 (as we
can prescale with multiples of 2). If user has given rate to be programmed as
22 MHz, then driver programmes it to 41.5 MHz. This looks to be incorrect, as
user might have given the upper limit of the device, and we are programming it
above it.
- Driver finds the first satisfying rate and programmes it, but with other
values of scr & cpsdvsr, it is possible to get more closer rate.
This patch fixes these two issues, with some reformatting inside the code. This
also creates a inline routine to calculate prescaled rate based on spi's rate,
cpsdvsr and scr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In routine configure_dma(), if transfer->len = PAGE_SIZE, then pages is one more
than required. While leads to one more sg getting allocated.
This is wrong. Correct this to allocate correct number of sg.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
tasklets don't allow invocation to sleeping routines. In configure_dma()
routine, sg_alloc_table() was called with GFP_KERNEL flag and so this causes
crash when called from tasklet.
Replace GFP_KERNEL with GFP_ATOMIC to get this fixed.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
- Replace multiple spaces with tabs
- Remove spaces before labels
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The remove function in the PL022 driver cannot abort the remove
function any way, so restructure the code so as not to make that
assumption. Remove will now proceed no matter whether it can
stop the transfer queue or not.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The platform configuration can select custom FIFO watermarks, but
these may conflict the actual FIFO size of the PL022 variant if
set too high. So strengthen the sanity checks to deny any
conflicting settings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Insert notifiers for the runtime PM API. With this the runtime
PM layer kicks in to action where used.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Rebased to Linux 3.0-rc3, edit description]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Configure the DMA burstsize from the FIFO trigger level supplied
with the controller configuration data. This is based on a patch
from Virupax, but I rewrote it differently.
Reported-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Viresh Kumar