We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Enabling PXA DMA for the smc91x on the logicpd pxa270 produces
unacceptable interference with the TFT panel, so disable it. Also
delete the lpd270 versions of the SMC_{in,out}[bl]() macros, as they
aren't used, since the board only supports 16bit accesses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
[ARM] 3559/1: S3C2442: core and serial port
[ARM] 3557/1: S3C24XX: centralise and cleanup uart registration
[ARM] 3558/1: SMDK24XX: LED platform devices
[ARM] 3534/1: add spi support to lubbock platform
[ARM] 3554/1: ARM: Fix dyntick locking
[ARM] 3553/1: S3C24XX: earlier print of cpu idcode info
[ARM] 3552/1: S3C24XX: Move VA of GPIO for low-level debug
[ARM] 3551/1: S3C24XX: PM code failes to compile with CONFIG_DCACHE_WRITETHROUGH
[ARM] 3550/1: OSIRIS: fix serial port map for 1:1
[ARM] 3548/1: Fix the ARMv6 CPU id in compressed/head.S
[ARM] 3335/1: Old-abi Thumb sys_syscall broken
[ARM] 3467/1: [3/3] Support for Philips PNX4008 platform: defconfig
[ARM] 3466/1: [2/3] Support for Philips PNX4008 platform: chip support
[ARM] 3465/1: [1/3] Support for Philips PNX4008 platform: headers
[ARM] 3407/1: lpd7x: documetation update
[ARM] 3406/1: lpd7x: compilation fix for smc91x
[ARM] 3405/1: lpd7a40x: CPLD ssp driver
[ARM] 3404/1: lpd7a40x: AMBA CLCD support
[ARM] 3403/1: lpd7a40x: updated default configurations
[ARM] 3402/1: lpd7a40x: serial driver bug fix
...
Patch from Marc Singer
Reworking of the adaptation macros to allow driver to compile again
for the lpd7x's. Also, support added for the lh79520 so it may use
the smc91x.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the smc91x on the LogicPD PXA270 to
the smc91x driver.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All accessor's different methods are now selected with C code and unused
ones statically optimized away at compile time instead of being selected
with #if's and #ifdef's. This has many advantages such as allowing the
compiler to validate the syntax of the whole code, making it cleaner and
easier to understand, and ultimately allowing people to define
configuration symbols in terms of variables if they really want to
dynamically support multiple bus configurations at the same time (with
the unavoidable performance cost).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch support the SMC9111 present on DB1200 boards.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update SMC91x driver for m32r.
- Remove needless NONCACHE_OFFSET adjustment.
> [PATCH 2.6.14-rc4] m32r: NONCACHE_OFFSET in _port2addr
> Change _port2addr() not to add NONCACHE_OFFSET.
> Adding NONCACHE_OFFSET requires needless address adjusting by a driver
> using ioremap() like a SMC91x driver.
- Fix lots of warnings as following:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c: In function `smc_reset':
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:324: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:325: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:341: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:342: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
--ReaqsoxgOBHFXBhH
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Hi Jeff,
Here's a little patch fixing a typo in smc91x.h.
Regards,
Tony
--ReaqsoxgOBHFXBhH
Content-Type: text/x-chdr; charset=us-ascii
Content-Disposition: inline; filename="patch-fix-typo-smc91x.h"
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For boards that invert the SMC91x IRQ line (maybe an FPGA inverts it),
the set_irq_type() call can't assume IRQT_RISING. These particular
boards currently use OMAP-specific calls to change the trigger type,
but the boards break when set_irq_type() stops being a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
... and remove duplicate status defines.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Index: linux-2.6/drivers/net/smc91x.c
===================================================================
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Deepak Saxena