If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 18996f2db9 (ACPICA: Events: Stop unconditionally
clearing ACPI IRQs during suspend/resume) the status of ACPI events
is not cleared any more when entering the ACPI S5 system state (power
off) which causes some systems to power up immediately after turing
off power in certain situations.
That is a functional regression, so address it by making the code
clear the status of all ACPI events again when entering S5 (for
system-wide suspend or hibernation the clearing of the status of all
events is not desirable, as it might cause the kernel to miss wakeup
events sometimes).
Fixes: 18996f2db9 (ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume)
Reported-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Thomas Hänig <haenig@cosifan.de>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A small collection of fixes, sort of the usual at this point, all for
i.MX or OMAP:
- Enable ULPI drivers on i.MX to avoid a hang
- Pinctrl fix for touchscreen on i.MX51 ZII RDU1
- Fixes for ethernet clock references on am3517
- mmc0 write protect detection fix for am335x
- kzalloc->kcalloc conversion in an OMAP driver
- USB metastability fix for USB on dra7
- Fix touchscreen wakeup on am437x
-----BEGIN PGP SIGNATURE-----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=N/ik
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A small collection of fixes, sort of the usual at this point, all for
i.MX or OMAP:
- Enable ULPI drivers on i.MX to avoid a hang
- Pinctrl fix for touchscreen on i.MX51 ZII RDU1
- Fixes for ethernet clock references on am3517
- mmc0 write protect detection fix for am335x
- kzalloc->kcalloc conversion in an OMAP driver
- USB metastability fix for USB on dra7
- Fix touchscreen wakeup on am437x"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx_v4_v5_defconfig: Select ULPI support
ARM: imx_v6_v7_defconfig: Select ULPI support
ARM: dts: omap3: Fix am3517 mdio and emac clock references
ARM: dts: am335x-bone-common: Fix mmc0 Write Protect
bus: ti-sysc: Use 2-factor allocator arguments
ARM: dts: dra7: Disable metastability workaround for USB2
ARM: dts: imx51-zii-rdu1: fix touchscreen pinctrl
ARM: dts: am437x: make edt-ft5x06 a wakeup source
Pull x86/pti updates from Thomas Gleixner:
"Two small fixes correcting the handling of SSB mitigations on AMD
processors"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Fix the AMD SSBD usage of the SPEC_CTRL MSR
x86/bugs: Update when to check for the LS_CFG SSBD mitigation
Pull x86 fixes from Thomas Gleixner:
- Prevent an out-of-bounds access in mtrr_write()
- Break a circular dependency in the new hyperv IPI acceleration code
- Address the build breakage related to inline functions by enforcing
gnu_inline and explicitly bringing native_save_fl() out of line,
which also adds a set of _ARM_ARG macros which provide 32/64bit
safety.
- Initialize the shadow CR4 per cpu variable before using it.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mtrr: Don't copy out-of-bounds data in mtrr_write
x86/hyper-v: Fix the circular dependency in IPI enlightenment
x86/paravirt: Make native_save_fl() extern inline
x86/asm: Add _ASM_ARG* constants for argument registers to <asm/asm.h>
compiler-gcc.h: Add __attribute__((gnu_inline)) to all inline declarations
x86/mm/32: Initialize the CR4 shadow before __flush_tlb_all()
Pull scheduler fixes from Thomas Gleixner:
- The hopefully final fix for the reported race problems in
kthread_parkme(). The previous attempt still left a hole and was
partially wrong.
- Plug a race in the remote tick mechanism which triggers a warning
about updates not being done correctly. That's a false positive if
the race condition is hit as the remote CPU is idle. Plug it by
checking the condition again when holding run queue lock.
- Fix a bug in the utilization estimation of a run queue which causes
the estimation to be 0 when a run queue is throttled.
- Advance the global expiration of the period timer when the timer is
restarted after a idle period. Otherwise the expiry time is stale and
the timer fires prematurely.
- Cure the drift between the bandwidth timer and the runqueue
accounting, which leads to bogus throttling of runqueues
- Place the call to cpufreq_update_util() correctly so the function
will observe the correct number of running RT tasks and not a stale
one.
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kthread, sched/core: Fix kthread_parkme() (again...)
sched/util_est: Fix util_est_dequeue() for throttled cfs_rq
sched/fair: Advance global expiration when period timer is restarted
sched/fair: Fix bandwidth timer clock drift condition
sched/rt: Fix call to cpufreq_update_util()
sched/nohz: Skip remote tick on idle task entirely
Pull objtool fix from Thomas Gleixner:
"A single fix for objtool to address a bug in handling the cold
subfunction detection for aliased functions which was added recently.
The bug causes objtool to enter an infinite loop"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Support GCC 8 '-fnoreorder-functions'
Pull crypto fixes from Herbert Xu:
- add missing RETs in x86 aegis/morus
- fix build error in arm speck
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86 - Add missing RETs
crypto: arm/speck - fix building in Thumb2 mode
maliciously crafted file system image can result in a kernel OOPS or
hang. At least one fix addresses an inline data bug could be
triggered by userspace without the need of a crafted file system
(although it does require that the inline data feature be enabled).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAltBmcYACgkQ8vlZVpUN
gaPDJgf/cEa9QuiYTbNOmcOMorK9LEk5XO8qsiJdUVNQtLsHZfl0QowbkF9/F/W5
andTJzNpFvXeLADMTTjpsDnQ90i8LKD11Kol3dPJcMhJhELtQsjxUBguxpQBP86R
dvHuCl2/AaqX7rr6Co80yYSinRCquqkzJNhdM5/MLNGziSpkQL3dPSs93rmV+YbU
8DkUwmhDhoiToLBTLaldrAsAzKvor3uyjNPJ3qhxeE2kXrnuI1V4XfstBGjhVKFB
/5aYWexDZkL5qiCo+lZnqdITqUnPx3uAkUdBn0dj7V+nDow+/R/8nApvlvJu6usF
OfMoKr098/pmPAjE5aZ8QpBNVtLFpg==
=njzR
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Bug fixes for ext4; most of which relate to vulnerabilities where a
maliciously crafted file system image can result in a kernel OOPS or
hang.
At least one fix addresses an inline data bug could be triggered by
userspace without the need of a crafted file system (although it does
require that the inline data feature be enabled)"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: check superblock mapped prior to committing
ext4: add more mount time checks of the superblock
ext4: add more inode number paranoia checks
ext4: avoid running out of journal credits when appending to an inline file
jbd2: don't mark block as modified if the handle is out of credits
ext4: never move the system.data xattr out of the inode body
ext4: clear i_data in ext4_inode_info when removing inline data
ext4: include the illegal physical block in the bad map ext4_error msg
ext4: verify the depth of extent tree in ext4_find_extent()
ext4: only look at the bg_flags field if it is valid
ext4: make sure bitmaps and the inode table don't overlap with bg descriptors
ext4: always check block group bounds in ext4_init_block_bitmap()
ext4: always verify the magic number in xattr blocks
ext4: add corruption check in ext4_xattr_set_entry()
ext4: add warn_on_error mount option
-----BEGIN PGP SIGNATURE-----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=IOF/
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix a use-after-free in the endpoint code (Dan Carpenter)
- Stop defaulting CONFIG_PCIE_DW_PLAT_HOST to yes (Geert Uytterhoeven)
- Fix an nfp regression caused by a change in how we limit the number
of VFs we can enable (Jakub Kicinski)
- Fix failure path cleanup issues in the new R-Car gen3 PHY support
(Marek Vasut)
- Fix leaks of OF nodes in faraday, xilinx-nwl, xilinx (Nicholas Mc
Guire)
* tag 'pci-v4.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
nfp: stop limiting VFs to 0
PCI/IOV: Reset total_VFs limit after detaching PF driver
PCI: faraday: Add missing of_node_put()
PCI: xilinx-nwl: Add missing of_node_put()
PCI: xilinx: Add missing of_node_put()
PCI: endpoint: Use after free in pci_epf_unregister_driver()
PCI: controller: dwc: Do not let PCIE_DW_PLAT_HOST default to yes
PCI: rcar: Clean up PHY init on failure
PCI: rcar: Shut the PHY down in failpath
-----BEGIN PGP SIGNATURE-----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=x5ij
-----END PGP SIGNATURE-----
Merge tag '4.18-rc3-smb3fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five smb3/cifs fixes for stable (including for some leaks and memory
overwrites) and also a few fixes for recent regressions in packet
signing.
Additional testing at the recent SMB3 test event, and some good work
by Paulo and others spotted the issues fixed here. In addition to my
xfstest runs on these, Aurelien and Stefano did additional test runs
to verify this set"
* tag '4.18-rc3-smb3fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix stack out-of-bounds in smb{2,3}_create_lease_buf()
cifs: Fix infinite loop when using hard mount option
cifs: Fix slab-out-of-bounds in send_set_info() on SMB2 ACE setting
cifs: Fix memory leak in smb2_set_ea()
cifs: fix SMB1 breakage
cifs: Fix validation of signed data in smb2
cifs: Fix validation of signed data in smb3+
cifs: Fix use after free of a mid_q_entry
Note that the LZ4 signature is different than that of modern LZ4 as we
use the "legacy" format which suffers from some downsides like inability
to disable compression.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Driver fixes for k3dma (off by one), pl330 (burst residue granularity)
and omap-dma (incorrect residue_granularity)
- Sinan's email update
-----BEGIN PGP SIGNATURE-----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=pPiU
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.18-rc4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"We have few odd driver fixes and one email update change for you this
time:
- Driver fixes for k3dma (off by one), pl330 (burst residue
granularity) and omap-dma (incorrect residue_granularity)
- Sinan's email update"
* tag 'dmaengine-fix-4.18-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: k3dma: Off by one in k3_of_dma_simple_xlate()
dmaengine: pl330: report BURST residue granularity
MAINTAINERS: Update email-id of Sinan Kaya
dmaengine: ti: omap-dma: Fix OMAP1510 incorrect residue_granularity
an interrupt issue, and one oops fix if init fails in a certain
way on the client driver.
-corey
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lLfC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.18-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"A couple of small fixes: one to the BMC side of things that fixes an
interrupt issue, and one oops fix if init fails in a certain way on
the client driver"
* tag 'for-linus-4.18-2' of git://github.com/cminyard/linux-ipmi:
ipmi: kcs_bmc: fix IRQ exception if the channel is not open
ipmi: Cleanup oops on initialization failure
Don't access the provided buffer out of bounds - this can cause a kernel
out-of-bounds read when invoked through sys_splice() or other things that
use kernel_write()/__kernel_write().
Fixes: 7f8ec5a4f0 ("x86/mtrr: Convert to use strncpy_from_user() helper")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180706215003.156702-1-jannh@google.com
In commit ca04d9d3e1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on
Qcom chips") you can see a call like:
devm_nvmem_cell_get(dev, NULL);
Note that the cell ID passed to the function is NULL. This is because
the qcom-qusb2 driver is expected to work only on systems where the
PHY node is hooked up via device-tree and is nameless.
This works OK for the most part. The first thing nvmem_cell_get()
does is to call of_nvmem_cell_get() and there it's documented that a
NULL name is fine. The problem happens when the call to
of_nvmem_cell_get() returns -EINVAL. In such a case we'll fall back
to nvmem_cell_get_from_list() and eventually might (if nvmem_cells
isn't an empty list) crash with something that looks like:
strcmp
nvmem_find_cell
__nvmem_device_get
nvmem_cell_get_from_list
nvmem_cell_get
devm_nvmem_cell_get
qusb2_phy_probe
There are several different ways we could fix this problem:
One could argue that perhaps the qcom-qusb2 driver should be changed
to use of_nvmem_cell_get() which is allowed to have a NULL name. In
that case, we'd need to add a patche to introduce
devm_of_nvmem_cell_get() since the qcom-qusb2 driver is using devm
managed resources.
One could also argue that perhaps we could just add a name to
qcom-qusb2. That would be OK but I believe it effectively changes the
device tree bindings, so maybe it's a no-go.
In this patch I have chosen to fix the problem by simply not crashing
when a NULL cell_id is passed to nvmem_cell_get().
NOTE: that for the qcom-qusb2 driver the "nvmem-cells" property is
defined to be optional and thus it's expected to be a common case that
we would hit this crash and this is more than just a theoretical fix.
Fixes: ca04d9d3e1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 9aaa3b8b4c ("thunderbolt: Add support for preboot ACL")
introduced boot_acl attribute but missed the fact that now userspace
needs to poll the attribute constantly to find out whether it has
changed or not. Fix this by sending notification to the userspace
whenever the boot_acl attribute is changed.
Fixes: 9aaa3b8b4c ("thunderbolt: Add support for preboot ACL")
Reported-and-tested-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Christian Kellner <christian@kellner.me>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are hitting a regression with the following commit:
commit a93e7b3315
Author: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Date: Mon May 14 13:32:23 2018 +1200
uio: Prevent device destruction while fds are open
The problem is the addition of spin_lock_irqsave in uio_write. This
leads to hitting uio_write -> copy_from_user -> _copy_from_user ->
might_fault and the logs filling up with sleeping warnings.
I also noticed some uio drivers allocate memory, sleep, grab mutexes
from callouts like open() and release and uio is now doing
spin_lock_irqsave while calling them.
Reported-by: Mike Christie <mchristi@redhat.com>
CC: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If 'fpga_mgr_create()' fails, we should release some resources, as done
in the other error handling path of the function.
Fixes: 7085e2a94f ("fpga: manager: change api, don't use drvdata")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PXA3xx platforms have 56 interrupts that are stored in two ICMR
registers. The code in pxa_irq_suspend() and pxa_irq_resume() however
does a simple division by 32 which only leads to one register being
saved at suspend and restored at resume time. The NAND interrupt
setting, for instance, is lost.
Fix this by using DIV_ROUND_UP() instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This read handler had a lot of custom logic and wrote outside the bounds of
the provided buffer. This could lead to kernel and userspace memory
corruption. Just use simple_read_from_buffer() with a stack buffer.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is two minor bug fixes (aacraid, target) and a fix for a
potential exploit in the way sg handles teardown.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWz/hBSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUkIAP9JKGYO
rcoNxusKsTi6tMEeUFzX1Mu0IkUr9ApcsCJMyAEAyRL5+b77PoZG8NgQBBo99iFE
8DMbxsNbBMbTzDqbfzk=
=ttS3
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is two minor bug fixes (aacraid, target) and a fix for a
potential exploit in the way sg handles teardown"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: mitigate read/write abuse
scsi: aacraid: Fix PD performance regression over incorrect qd being set
scsi: target: Fix truncated PR-in ReadKeys response
- Build cleanup/fix for the sunxi makefile that tried to save size
but failed and prevented dead code elimination from working
- Two Davinci clk driver fixes for a typo causing build failures
in different configurations and an error check that checks
the wrong variable.
- Undo the DT ABI breaking imx6ul binding header shuffle that got
merged this cycle.
-----BEGIN PGP SIGNATURE-----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=pNsb
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"The usual collection of driver fixlets:
- build cleanup/fix for the sunxi makefile that tried to save size
but failed and prevented dead code elimination from working
- two Davinci clk driver fixes for a typo causing build failures in
different configurations and an error check that checks the wrong
variable.
- undo the DT ABI breaking imx6ul binding header shuffle that got
merged this cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
dt-bindings: clock: imx6ul: Do not change the clock definition order
clk: davinci: fix a typo (which leads to build failures)
clk: davinci: cfgchip: testing the wrong variable
clk: sunxi-ng: replace lib-y with obj-y
Pull s390 fixes from Martin Schwidefsky:
"A few more changes for v4.18:
- wire up the two new system calls io_pgetevents and rseq
- fix a register corruption in the expolines code for machines
without EXRL
- drastically reduce the memory utilization of the dasd driver
- fix reference counting for KVM page table pages"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: wire up rseq system call
s390: wire up io_pgetevents system call
s390/mm: fix refcount usage for 4K pgste
s390/dasd: reduce the default queue depth and nr of hardware queues
s390: Correct register corruption in critical section cleanup
RTL8822be can't bring up properly on ASUS X530UN, and dmesg says:
[ 8.591333] r8822be: module is from the staging directory, the quality
is unknown, you have been warned.
[ 8.593122] r8822be 0000:02:00.0: enabling device (0000 -> 0003)
[ 8.669163] r8822be: Using firmware rtlwifi/rtl8822befw.bin
[ 9.289939] r8822be: rtlwifi: wireless switch is on
[ 10.056426] r8822be 0000:02:00.0 wlp2s0: renamed from wlan0
...
[ 11.952534] r8822be: halmac_init_hal failed
[ 11.955933] r8822be: halmac_init_hal failed
[ 11.956227] r8822be: halmac_init_hal failed
[ 22.007942] r8822be: halmac_init_hal failed
Jian-Hong reported it works if turn off ASPM with module parameter aspm=0.
In order to fix this problem kindly, this commit don't turn off aspm but
enlarge ASPM L1 latency to 7.
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f28e4c24b (thermal: armada: Clarify control registers
accesses) introduced the new thermal binding. The new binding extends
the second registers field size to 8. Switch to the new binding to fix
thermal reading values. Without this change the fix for errata #132698
introduced in commit 8c0b888f66 (thermal: armada: Change sensors trim
default value) has no effect.
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without that option, we run into a link failure:
drivers/usb/gadget/udc/aspeed-vhub/hub.o: In function `ast_vhub_std_hub_request':
hub.c:(.text+0x5b0): undefined reference to `usb_gadget_get_string'
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This parameter introduced several years ago in the XHCI host controller
driver was somehow left undocumented. Add a few lines in the kernel
parameters text.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=UDQ5
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
USB-serial fixes for v4.18-rc4
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
The comment is the same as in the top-level Makefile.
Also, the comments contain typos:
- the .PHONY variable -> the PHONY variable
- se we can ... -> so we can ...
Instead of fixing the typos, just remove the duplicated comments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The comment line for addtree says "skip if -I has no parameter".
What it actually does is "drop if -I has no parameter". For example,
if you have the compiler flag '-I foo' (a space between), it will be
converted to 'foo'. This completely changes the meaning.
What we want is, "do nothing" for -I without parameter so that
'-I foo' is kept as-is.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add usage info for the Kbuild environment variable KBUILD_KCONFIG.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Update Documentation/kbuild/kconfig.txt, which mostly contains
user help for using the kernel config tools.
- Add mention of 'nconfig' embedded help text.
- Make the section on new config symbols readable.
- Correct how to find menuconfig search help.
- Add section on 'nconfig' usage.
- Mention that gconfig has multiple viewing modes/options.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Removed Kbuild documentation for INSTALL_FW_PATH.
The kbuild symbol INSTALL_FW_PATH was removed from Kbuild tools in
September 2017 (for 4.14) but the symbol was not deleted from
the kbuild documentation, so do that now.
Fixes: 5620a0d1aa ("firmware: delete in-kernel firmware")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: stable@vger.kernel.org # 4.14+
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The supported alias for building sparc 32-bit is "sparc32",
not "sparc", so update the alias documentation for that.
Just using "sparc" produces a 64-bit config file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In Kbuild documentation, add alias for 64-bit sh ARCH ("sh64")
to the list of ARCH aliases.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We have two new lenovo desktop models which need to apply the fixup of
ALC294_FIXUP_LENOVO_MIC_LOCATION, and they have the same pin cfg as
the machine with subsystem id:0x17aa3136, now use the pincfg table
to apply the fixup for them.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Stefan Agner