The bnx2/bnx2x rings are made up of linked pages. However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface. In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE. On archs with >= 64K PAGE_SIZE, it generates some compile
warnings. Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For per device operations, cnic needs to dereference the RCU protected
cp->ulp_ops instead of the global cnic_ulp_tbl. In 2 locations,
cnic_send_nlmsg() and cnic_copy_ulp_stats(), it was referencing the
global table. If the device has been unregistered and these functions
are still being called (very unlikely scenarios), it could lead to NULL
pointer dereference.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a context modified revert of commit 6a9612e2cb
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.
The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.
Fixes: 6a9612e2cb ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlMmuSEACgkQjTAFq1RaXHOWUgCfbyIIhBEltzY+EtX+RNdVAS4j
KkwAnAz4iZJY+3SdjRyy5uG2mjhWRS/B
=RnxD
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.15-20140317' of git://gitorious.org/linux-can/linux-can-next
linux-can-next-for-3.15-20140317
Marc Kleine-Budde says:
====================
this is a pull request of three patches for net-next/master.
It consists of a patch by Oliver Hartkopp, which unifies the MTU
settings for CAN interfaces. A patch by Christopher R. Baker populates
netdev::dev_id for udev discrimination for multi interface CAN devices.
Alexander Shiyan contributes a patch for the mcp251x driver which fixes
the regulators operation if CONFIG_REGULATOR is not enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In generic, after an assignment, we use ';' instead of ','.
Although, it won't hurt.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current firmware advertises support for uAPSD, but
critical bugs force us to disable the feature.
When a fixed firmware will be available, we will be able to
re-enable uAPSD.
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the low-latency update is called but there's no change then
ignore the update instead of triggering all the required work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove a spurious blank line in the quota code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of system low latency configure passive scan to be fragmented.
Set the following scan parameters for both immediate and scheduled scan:
- passive scan fragment duration = 20ms
- out-of-channel time = 70ms
- suspend time = 105ms
Restructure channel's active/passive dwell time configuration to better
suit the above change.
The idea is that under low latency traffic passive scan is fragmented,
i.e. that dwell on a particular channel will be fragmented. Each
fragment dwell time is 20ms and fragments period is 105ms. Skipping to
next channel will be delayed by the same period (105ms). So suspend_time
parameter describing both fragments and channels skipping periods is set
to 105ms. This value is chosen so that overall passive scan duration
will not be too long. Max_out_time in this case is set to 70ms, so for
active scanning operating channel will be left for 70ms while for
passive still for 20ms (fragment dwell).
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some scan parameters should be dependent on traffic conditions.
Centralize conditions verification in one function and obtain
scan max out-of-channel and suspend time in that new function.
Rely on bound interfaces indication instead of association state
to calculate scan parameters. If no bound interfaces use default
values for out-of-channel and suspend time parameters.
Additionally, get rid of NL80211_SCAN_FLAG_LOW_PRIORITY checks
since no use case for this exists so far.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware decided to not implement this API in this way,
so for now remove setting the field completely. This will
allow the firmware to change how to use this field later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to debug the firmware, we need to be able to set
the BT priority of WiFi packets. This priority is set based
on the type of the packet (control frames, EAPOL etc...).
For debugging purposes, allow to override this priority by
a debugfs controlled value.
Enable this feature that needs this priority to be able to
test it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the firmware asserts, the driver will dump the firmware
state to an internal buffer. This buffer is kept aside until
it is dumped through debugfs. Once an external application
fetched the data, the buffer is freed and a new buffer can
be allocated in case another assert occurs.
A udev event is sent to trigger an external application.
A simple rule like:
DRIVER=="iwlwifi", ACTION=="change", RUN+="/sbin/dump_sram.sh"
can fetch the data from debugfs.
Here is my dump_sram.sh:
phyname=$(basename ${DEVPATH})
date=$(date +%F_%H_%M)
filename=/var/log/iwl-sram-${phyname}-${date}.bin
cat /sys/kernel/debug/ieee80211/${phyname}/iwlwifi/iwlmvm/fw_error_dump > ${filename}
The current SRAM size is 80KB so, currently:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin
-rw-r--r-- 1 emmanuel emmanuel 81K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin
and after compression:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin.xz
-rw-r--r-- 1 emmanuel emmanuel 13K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin.xz
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Only ratelimit the ones that might spam, omiting the ones from
enslave/deslave.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The networking core does it for the driver during registration time.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling the i40e and the i40evf driver into the same kernel I get:
LD drivers/net/ethernet/intel/built-in.o
drivers/net/ethernet/intel/i40evf/built-in.o:(.data+0x300): multiple definition of `i40e_ptype_lookup'
drivers/net/ethernet/intel/i40e/built-in.o:(.data+0x780): first defined here
make[3]: *** [drivers/net/ethernet/intel/built-in.o] Error 1
make[2]: *** [drivers/net/ethernet/intel] Error 2
make[1]: *** [drivers/net/ethernet/] Error 2
make: *** [sub-make] Error 2
Fix this by renaming the i40evf version of this structure from
i40e_ptype_lookup to i40evf_ptype_lookup.
This build failure was introduced in:
commit 206812b5fc
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
i40e/i40evf: i40e implementation for skb_set_hash
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Eric W Biederman <ebiederm@xmission.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 2800209994 (e1000e: Refactor PM flows) changed the
SET_SYSTEM_SLEEP_PM_OPS to open-coded assignment, but forgot to
protect them with CONFIG_PM_SLEEP. Then cause the following build
error when PM is disabled:
drivers/net/ethernet/intel/e1000e/netdev.c:7079:13:
error: 'e1000e_pm_suspend' undeclared here (not in a function)
.suspend = e1000e_pm_suspend,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7080:13:
error: 'e1000e_pm_resume' undeclared here (not in a function)
.resume = e1000e_pm_resume,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7082:11:
error: 'e1000e_pm_thaw' undeclared here (not in a function)
.thaw = e1000e_pm_thaw,
^
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command line parameters QueuePairs, Node, EEE, DMAC and InterruptThrottleRate
do not exist these days. Remove all references to them in the Documentation
folder and update code comments.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f280e89a (drivers: net: cpsw: fix for cpsw crash when build as modules)
moved cpts_register()/cpts_unregister() to ndo_open()/ndo_stop(), but failed
to remove cpts_register in cpsw_probe() which leads to a double registration
and the following debug object splat.
[ 18.991902] ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x2c
[ 19.082249] [<c0059e80>] (init_timer_key) from [<c04965d4>] (cpts_register+0x1f0/0x2c4)
[ 19.090642] [<c04965d4>] (cpts_register) from [<c04931dc>] (cpsw_ndo_open+0x780/0x81c)
[ 19.098948] [<c04931dc>] (cpsw_ndo_open) from [<c0599c2c>] (__dev_open+0xb4/0x118)
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the Ethernet Makefile and Kconfig files to add the Altera
Ethernet driver component.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Altera Triple Speed Ethernet Makfile and
Kconfig file.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the main driver and header file for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds miscellaneous files for the Altera Ethernet Driver,
including ethtool support.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the SGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the MSGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. For the 64 bits dma mask use dma_set_mask_and_coherent instead of
dma_set_mask and dma_set_coherent_mask.
2. For the 32 bits dma mask dma_set_coherent_mask is only called if
dma_set_mask fails, which is unusual. Assuming this as a bug, fixes
it by replacing calls to dma_set_mask and dma_set_coherent_mask by a
call to dma_set_mask_and_coherent.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds devicetree support for the at86rf230 driver.
Possible gpios to configure are "reset-gpio" and "sleep-gpio".
Also add support to configure the "irq-type" for the irq polarity
register.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make the reset pin optionally. Some devices like the atben
from qi-hardware don't have a reset pin externally. The usually way is
to turn power off/on for the atben device to initiate a device reset.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While checkpatch another patch I got a:
"WARNING: msleep < 20ms can sleep for up to 20ms"
The datasheet of at86rf231 and at86rf212 says a minimum delay for reset
pulse width and spi access latency after reset is 625 nanoseconds.
This patch removes the 1 milliseconds sleep and replace it with a 1
microseconds udelay which should be also okay for the reset pulse width.
To change the state from RESET -> TRX_OFF the at86rf230 device needs 120
microseconds, this is a worst case of all at86rf* chips.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to lock the clearing of IRQ_TRX_END in status.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a unexpected state change for the at86rf231 chip.
We can't change into STATE_FORCE_TX_ON while the chip is in one of
SLEEP, P_ON, RESET, TRX_OFF, and all *_NOCLK states.
In this case we are in the TRX_OFF state. See datasheet [1] page 71 for
more information.
Without this patch you will get the following message on a at86rf231 device:
[ 20.065218] unexpected state change: 8, asked for 4
[ 20.070527] ------------[ cut here ]------------
[ 20.075414] WARNING: CPU: 0 PID: 160 at net/mac802154/ieee802154_dev.c:43 mac802154_slave_open+0x70/0xb8()
[ 20.085594] Modules linked in: autofs4
[ 20.089667] CPU: 0 PID: 160 Comm: ifconfig Not tainted 3.14.0-20140108-1-00993-g905c192 #162
[ 20.098612] [<c00127b8>] (unwind_backtrace) from [<c0010b1c>] (show_stack+0x10/0x14)
[ 20.106819] [<c0010b1c>] (show_stack) from [<c0033838>] (warn_slowpath_common+0x60/0x80)
[ 20.115311] [<c0033838>] (warn_slowpath_common) from [<c00338e8>] (warn_slowpath_null+0x18/0x20)
[ 20.124590] [<c00338e8>] (warn_slowpath_null) from [<c057b7e8>] (mac802154_slave_open+0x70/0xb8)
[ 20.133880] [<c057b7e8>] (mac802154_slave_open) from [<c0488a58>] (__dev_open+0xa8/0x108)
[ 20.142553] [<c0488a58>] (__dev_open) from [<c0488cb0>] (__dev_change_flags+0x8c/0x148)
[ 20.151051] [<c0488cb0>] (__dev_change_flags) from [<c0488d84>] (dev_change_flags+0x18/0x48)
[ 20.159968] [<c0488d84>] (dev_change_flags) from [<c04e2e9c>] (devinet_ioctl+0x2b0/0x63c)
[ 20.168623] [<c04e2e9c>] (devinet_ioctl) from [<c04712e4>] (sock_ioctl+0x23c/0x29c)
[ 20.176727] [<c04712e4>] (sock_ioctl) from [<c00e3cb8>] (do_vfs_ioctl+0x4a8/0x578)
[ 20.184671] [<c00e3cb8>] (do_vfs_ioctl) from [<c00e3dd4>] (SyS_ioctl+0x4c/0x78)
[ 20.192402] [<c00e3dd4>] (SyS_ioctl) from [<c000da00>] (ret_fast_syscall+0x0/0x48)
[ 20.200392] ---[ end trace 9a34542f4ea08e47 ]---
This patch was tested on at86rf231 and at86rf212.
[1] http://www.atmel.com/images/doc8111.pdf
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we call netdev_*() under netif_msg_*() checks, we can fold these into
netif_*() macro invocations.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert dev_*(&ndev->dev, ...) to netdev_*(ndev, ...) calls since they are a bit
shorter and at the same time give more information on a device.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert pr_*() to netdev_*() calls as the latter provide info on a device.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exit the driver's probe() method when the register layout is unknown as the
driver would cause kernel oops in this case anyway.
While at it, move the corresponding error message printout and convert it from
pr_err() to dev_err().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.
All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.
There are problems with the netpoll packet receive code. __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context. netpoll_neigh_reply leaks every skb it receives. Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).
Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.
Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Redpine Signals' 91x wireless driver.
Signed-off-by: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disconnecting some CID, corresponded Tx vring get released. During vring
release, all descriptors get freed. It is possible that Tx NAPI working on the same
vring simultaneously. If it happens, descriptor may be double freed.
To protect from the race above, make sure NAPI won't process the same vring.
Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if
'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI
get synchronized.
NAPI enablement status protected by wil->mutex, add protection where it was
missing and check for it.
During reset, disconnect all peers first, then proceed with the Rx vring. It allows for
the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about
connection status change
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
make sure reset flow executed in order
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 'real' indication for hardware state.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GRO is easy to enable when already using NAPI framework,
and it improves CPU utilisation. Enable it by default.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These methods can change device state, serialize with others
similar ones like up/down
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when STA receiving connect() when already connected,
it should return error
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
upon fw error interrupt - in STA mode, disconnect/cancel scan and
then reset FW/HW
added module param - no_fw_recovery which is false by default
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wil_reset() removes vring's
At the same time NAPI may be active performing Rx/Tx completion.
If this happens, Rx/Tx polling functions going to access already removed vrings
Make sure NAPI is idle and won't be started prior to vring removal.
For this, track NAPI enabled state
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When switching between STA and AP modes, memory allocated for Rx vring leaks
This is because start_ap() allocates Rx vring but stop_ap() do not free it.
Logically, Rx vring is not valid (HW can't use it anymore), so free it in reset()
Also, check double init for Rx vring and bail out with -EINVAL
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert 2 often printed messages to dynamic ones
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure hardware to perform full reset on "power good". This mean,
reset HW on system boot. This improves card stability.
By default this is off.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put all registers in order for easier navigation;
fix naming to reflect hardware cluster
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware bug triggered by the MSI init while INTx asserted for some reason.
De-assert INTx prior to MSI set-up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Useful to detect hardware problems
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FW crashes, dmesg get polluted with the "FW not ready"
error message. Print it only once per FW lifecycle
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for new chip revision. Revision read from the
internal register, PCIE config's "revision id" register
do not indicate HW version properly
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce enum to describe mapping type; allow 'none' in addition to
'single' and 'page'; this is preparation for GSO
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting fragmented skb for Tx, assign skb to the last descriptor
and set number of fragments in the 1-st one
On Tx complete, HW sets "DU" bit in Tx descriptor only for the last
descriptor; so search for it using number of fragments field.
Middle descriptors may have "DU" bit not set by the hardware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New firmware do support scan while connected. Enable it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connection established, as reported by WMI_CONNECT_EVENTID,
4-way handshaking required for the secure connection is not done
yet. It is indicated by another WMI event. Wait for it and only then
allow data traffic. In case of non-secure connection, FW reports
"data port open" immediately after connection.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers for temperature compensation need to
be programmed only for active chains. Use the TX chainmask
to make sure that this is done properly for QCA953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eeprom read operations are mixed in the probe function.
Make the code more readable and clean by extracting this code and
moving it in a dedicated function.
The variable eeprom_cck_table_adr, now useless, is here because
it will be needed for rtl8187se support, that I hope to add soon.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SLOT, SIFS, DIFS, EIFS, CW and ACK-timeout registers are set in an
RF-code callback and their values are fixed.
This patch moves this off the rf-code, and introduce two new functions
that calculate these values depending by slot time and CW values
requested by mac80211.
This seems to improve performances on my setup.
Currently the ack and slot time values could be stored in a local
variable, but this patch stores it in the driver "priv" structure
because it will be useful for rtl8187se support that will be added
(hopefully) soon.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basic rates setting is done with hardcoded register write with
fixed settings.
This patch introduces a new function that makes it possible to
configure basic rates and it add a check for mac80211
BSS_CHANGED_BASIC_RATES flag in order to eventually invoke that
function when needed.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While changing board-type variable to enum, I have added enum
value for rtl8187se by mistake.
This will causes gcc warnings with unhandled switch/cases.
Remove it temporarily until I will push also rtl8187se changes.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 iftype was converted to a mode value and stored in
brcmf_cfg80211_vif structure. The value was used only within
brcmfmac driver to decide execution of conditional code. Better
use wireless_dev::iftype for that as the wdev is contained in
the brcmf_cfg80211_vif structure.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the SDIO driver goes in low power state it must assure that
a clock request in ChipCLKCSR is set. Otherwise waking up the
device can fail. The register is read and if necessary the ALP
clock will be requested.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connecting without specifying the channel it can take quite
some time to connect. This is because not all parameters for the
scan operation are set to optimized values. This patch changes
these parameters resulting in a much faster connect in certain
situations.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO tx uses a sequence number which is common for data
and control. This requires that access to this sequence number
is protected. A mutex was used to achieve this, but it also
required the reordering of code for tx control.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through
SDIO interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we will need it to make common-beacon code work.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we will need it for ath9k_htc, may be other drivers too
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to reduce difference between ath9k and ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If CONFIG_REGULATOR is not set, devm_regulator_get() returns NULL,
so use IS_ERR_OR_NULL() macro for checks.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
My objective is to be able to totally discriminate CAN ports on multi-port
cards via udev so as to rename them to semantically interesting/unique names
for my system (e.g., "ecuCAN" and "auxCAN" instead of "can0" and "can1").
The following patch assigns the dev_id field to match the channel number on all
multi-channel devices. I can only test my two-port Peak PCI card, but it works
as expected: ATTRS{dev_id} now expresses the port number and my udev rules now
unambiguously pick out and rename my individual CAN ports.
Signed-off-by: Christopher R. Baker <cbaker@rec.ri.cmu.edu>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> [PEAK PCAN-USB pro and EMS PCMCIA]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN interfaces only support MTU values of 16 (CAN 2.0) and 72 (CAN FD).
Setting the MTU to other values is pointless but it does not really hurt.
With the introduction of the CAN FD support in drivers/net/can a new
function to switch the MTU for CAN FD has been introduced.
This patch makes use of this can_change_mtu() function to check for correct
MTU settings also in legacy CAN (2.0) devices.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable protocol offloading (arp and NS) on D0i3.
The offloading allows the fw answer NS and arp requests
without waking up the host.
Since protocol offloading is saved between D0i3
entries, we have to explicitly disable it in
case we don't want it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to restore the qos seq number on d0i3 exit,
we need to read it from the wowlan status.
However, in order to make sure we use correct seq num
for tx frames, we need to defer any outgoing frames,
and re-enqueue them only after the seq num is configured
correctly.
Sync new Tx aggregations with D0i3 so that the correct
seq num is used for them. Wait synchronously for D0i3
exit before starting a new Tx agg.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure the QoS counters when entering D0i3.
The fw might use them later when performing protocol
offloading (we'll update the the counters back on
d0i3 exit in a following patch).
Non-QoS counter is handled internally in the fw, so
no need to configure it.
Also, add support for a new version of WOWLAN_CONFIG_CMD
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable beacon filter only if at least one beacon from candidate
AP is received before or after association. Check this condition before
enabling BF upon secured association completion. Add BF enablement to
mac80211 event that indicates beacon is received after association.
Too early beacon filtering enablement can lead to disconnection due to
missing AP's beacon after association.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Blink led mode is not supported by iwlmvm. This doesn't mean
that we should prevent any operation if it is selected by
the user.
Instead of failing without any notice to the user, fallback
to the default mode (RF mode) if the blink mode
is selected and print an error to inform the user.
Reported-by: Steven Haigh <netwiz@crc.id.au>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
instead of duplicating the same loop multiple times,
use a new function for it.
this will be later used also for clearing other
windows in the table.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make _rs_collect_tx_data get window as param, in order
to be able to set various windows.
This will be used later for saving tpc statistics
as well.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently RTS protection was done whenever trasnmitting an AMPDU.
This limits throughput in cases where there's no need for protection.
Disable this too inclusive protection for now.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We should explore all possible columns when searching to be
as resilient as possible to changing conditions. This fixes
for example a scenario where even after a sudden creation of
rssi difference between the 2 antennas we would keep doing MIMO
at a low rate instead of switching to SISO at a higher rate using
the better antenna which was the optimal configuration.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scheduled scan was disabled because it was broken. Now it is
fixed and got disabled by mistake by a merge.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull these last(?) few wireless bits intended for the 3.14
stream. Each is here to address a problem found with a patch already
merged...
Dave Jones gives us a memory leak fix, for an error path in brcmfmac.
Felix Fietkau moves a small delay to make it actually reachable.
Helmut Schaa fixes an ath9k sequence numbering problem for non-data
frames.
Stanislaw Gruszka reverts an earlier fix that was found to cause
random connection drops on RT5390 PCI adapters
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.
Design:
cxgb4:
Direct ULD callback from the DB FULL/DROP interrupt handler. This allows
the ULD to stop doing user DB writes as quickly as possible.
While user DB usage is disabled, the LLD will accumulate DB write events
for its queues. Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count. This reduces the
load put on the DB fifo when reenabling.
iw_cxgb4:
Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps. This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs. If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP. Thus we allow the new driver to work with an older libcxgb4.
When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED. As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events. Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.
When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list. This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example). QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO. Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain. This prevents resuming to
quickly and overflowing the FIFO. Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.
The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops. As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Anand Priyadarshee <anandp@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of phy_ethtool_get_wol are supposed to provide a properly
cleared struct ethtool_wolinfo. Therefore, fix phy_suspend to clear
it before passing it to phy_ethtool_get_wol.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's using the wrong ETH_P_LOOP type, which is sometimes treated
as packet length instead of ether type (because it's 0x0060).
Use the new ETH_P_LOOPBACK type.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, i40e and i40evf.
I provide a code comment fix which David Miller noticed in the last
series of patches I submitted.
Shannon provides a patch to cleanup the NAPI structs when deleting the
netdev.
Anjali provides several patches for i40e, first fixes a bug in the update
filter logic which was causing a kernel panic. Then provides a fix to
rename an error bit to correctly indicate the error. Adds a definition
for a new state variable to keep track of features automatically disabled
due to hardware resource limitations versus user enforced feature disabled.
Anjali provides a patch to add code to handle when there is a filter
programming error due to a full table, which also resolves a previous
compile warning about an unused "*pf" variable introduced in the last i40e
series patch submission.
Jesse provides three i40e patches to cleanup strings to make more
consistent and to align with other Intel drivers.
Akeem cleans up a misleading function header comment for i40e.
Mitch provides a fix for i40e/i40evf to use the correctly reported number
of MSI-X vectors in the PF an VF. Then provides a patch to use
dma_set_mask_and_coherent() which was introduced in v3.13 and simplifies
the DMA mapping code a bit.
v2:
- dropped the 2 ixgbe patches from Emil based on feedback from David Miller,
where the 2 fixes should be handled in the net core to fix all drivers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all internal uses of ieee802154_addr_sa to ieee802154_addr,
except for those instances that communicate directly with userspace.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable sparse warnings about endianness, replace the remaining fields
regarding network operations without explicit endianness annotations
with such that are annotated, and propagate this through the entire
stack.
Uses of ieee802154_addr_sa are not changed yet, this patch is only
concerned with all other fields (such as address filters, operation
parameters and the likes).
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct as currently defined uses host byte order for some fields,
and most big endian/EUI display byte order for other fields. Inside the
stack, endianness should ideally match network byte order where possible
to minimize the number of byteswaps done in critical paths, but this
patch does not address this; it is only preparatory.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Linux 3.13, dma_set_mask_and_coherent was introduced, and we have
been encouraged to use it. It simplifies the DMA mapping code a bit as
well.
Change-ID: I66e340245af7d0dedfa8b40fec1f5e352754432e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the 2.4 firmware reports the correct number of MSI-X vectors,
use this value correctly when communicating with the VF, and when
setting up the interrupt linked list.
The PF has always reported the correct number of MSI-X vectors, so we
should never increment the value in the vf driver.
Change-ID: Ifeefc631c321390192219ce2af9ada6180c1492f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have a separate handler for MDD events, a generic reset is not required.
Change-ID: I77858e2d479e4e65c52aede67109464649ea0253
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FDIR replay logic was being run a little too soon (before the
queues were enabled) and hence the tail bump was not effective till
a later transaction happened on the queue.
Change-ID: Icfd7cd2e79fc3cae3cbd3f703a2b3a148b4e7bf6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to enforce the following policy:
- If the HW reports filter programming error, we check if it's due to a
full table.
- If so, we go ahead and turn off new rule addition for ATR and then SB
in that order.
- We monitor the programmed filter count, if enough room is created due
to filter deletion/reset, we then re-enable SB and ATR new rule addition.
Change-ID: I69d24b29e5c45bc4fa861258e11c2fa7b8868748
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This variable is a bit mask. It is needed to differentiate between
user enforced feature disables and auto disable of features due to
HW resource limitations.
Change-ID: Ib4b4f6ae1bb2668c12e482d2555100bc8ad713d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In a similar way to how ixgbe works, print a short one-line string
showing what features and number of queues the driver and hardware has
enabled at probe time.
Example (wrapped for the commit message):
i40e 0000:06:00.1: Features: PF-id[1] VFs: 64 VSIs: 66 QP: 32 FDir RSS
ATR NTUPLE DCB
Change-ID: I177bf7f93d1c4c921529c92fdf66e614f6b4f755
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the strings that the driver prints during normal
operation and moves many strings into dev_dbg. It also cleans up
strings printed during reset.
Change-ID: I1835cc4e3c3b22596182b683284e6bb87eac61b2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This cleans up strings for consistency, q is replaced with queue.
Change-ID: Ia5f9dfae9af261f4c24485854264e02363729cf3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Fix a name of the error bit to correctly indicate the error.
2) Added a fd_id field in the 32 byte desc at the place(qw0) where it gets
reported in the programming error desc WB. In a normal data desc
the fd_id field is reported in qw3.
Change-ID: Ide9a24bff7273da5889c36635d629bc3b5212010
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The update filter logic was causing a kernel panic in the original code.
We need to compare the input set to decide whether or not to delete a
filter since we do not have a hash stored. This new design helps fix the issue.
Change-ID: I2462b108e58ca4833312804cda730b4660cc18c9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We've been deleting the netdev before getting around to deleting the napi
structs. Unfortunately, we then didn't delete the napi structs because we
have a check for netdev, thus we were leaving garbage around in the system.
Change-ID: Ife540176f6c9f801147495b3f2d2ac2e61ddcc58
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the benefits of platform_driver_probe() is that you can make
the probe function __init.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On older chips, the INI value differ in similar ways as cycpwr_thr1, so
convert it to absolute values as well.
Since the ANI algorithm is different here compared to the old
implementation (fewer steps, controlled at a different point in time),
it makes sense to use values similar to what would be applied for newer
chips, just without relying on INI defaults.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The table was copied from the ANI implementation of AR9300. It assumes
that the INI values contain a baseline value that is usable as reference
from which to increase/decrease based on the noise immunity value.
On older chips, the differences are bigger and especially AR5008/AR9001
are configured to much more sensitive values than what is useful.
Improve ANI behavior by reverting to the absolute values used in the
previous implementation (expressed as a simple formula instead of the
old table).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The primary purpose of this piece of code was to selectively disable
OFDM weak signal detection. The checks for this are elsewhere, and an
earlier commit relaxed the restrictions for older chips, which are more
sensitive to interference.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 4c59ff221e "wireless: Kconfig: add missing dependency" added a number
of 'depends on CFG80211' statements, but missed the AIRO_CS driver that
also causes the airo.c file to be built. This adds the (hopefully) last
such missing statement
Cc: "Zhao, Gang" <gamerh2o@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcms_attach function is defined as static but the comment is
saying that it should not be static or gcc will issue a warning.
I believe we can remove the comment as I don't se a problem with
this function being defined as static.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When brcm80211 firmware is not installed networking hangs.
A deadlock happens because we call ieee80211_unregister_hw()
from the .start callback of struct ieee80211_ops. When .start
is called we are under rtnl lock and ieee80211_unregister_hw()
tries to take it again.
Function call stack:
dev_change_flags()
__dev_change_flags()
__dev_open()
ASSERT_RTNL() <-- Assert rtnl lock
ops->ndo_open()
.ndo_open = ieee80211_open,
ieee80211_open()
ieee80211_do_open()
drv_start()
local->ops->start()
.start = brcms_ops_start,
brcms_ops_start()
brcms_remove()
ieee80211_unregister_hw()
rtnl_lock() <-- Here we deadlock
Introduced by:
commit 25b5632fb3
("brcmsmac: request firmware in .start() callback")
This patch fixes the bug by removing the call to brcms_remove()
and moves the brcms_request_fw() call to the top of the .start
callback to not initiate anything unless firmware is installed.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify scnprintf calls and include the current OFDM/CCK immunity level.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qi->tqi_readyTime is written directly to registers that expect
microseconds as unit instead of TU.
When setting the CABQ ready time, cur_conf->beacon_interval is in TU, so
convert it to microseconds before passing it to ath9k_hw.
This should hopefully fix some Tx DMA issues with buffered multicast
frames in AP mode.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently a "r8185" integer variable is used as a boolean flag to
indicate whether the card is a rtl8185 or not.
Since now the driver supports only rtl8185 and rtl8180 cards, if
"r8185" variable is zero then the card is implicitly assumed to
be a rtl8180.
Now I'm preparing to add support for a third card type (rtl8187se).
This patch changes the "r8185" flag with an enum variable to
explicitly indicate which card type we have.
I'm submitting this this patch now, even if I still have to submit
other patches that not pertain with rtl8187se support, because
IMHO it's not worth rebasing them on the current code, using r8185
flag, and then changing them back again nearly immediately.
BTW if someone feels I really should do this, please tell me..
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AMPDU aggregation is preferred over AMSDU. AMSDU
aggregation is performed only if AMPDU streams in firmware
are full.
This patch adds simultaneous AMSDU and AMPDU aggregation
support. This mechanism helps to improve throughput.
AMSDU is enabled only for 8897 chipsets which supports 4K
transmit buffer. User can disable AMSDU using
'disable_tx_amsdu' module parameter.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing mwifiex_11n_dispatch_pkt() function is renamed as
mwifiex_11n_dispatch_pkt_until_start_win() and a new function
mwifiex_11n_dispatch_pkt() is created for a common code which
dispatches single packet based on interface type.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use negative check for 'status' and return from the function.
This improves readability by avoiding line splits. Also, local
variable is used for start window calculations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As V15 firmware supports VHT rate configuration, we can use this
information received in set bitrate mask handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware API version number will be used for future patches
to support different firmware API specs.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If p54u_load_firmware() fails, p54u_probe() does not deallocate
already allocated resources. The patch adds proper failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking fixes from David Miller:
"I know this is a bit more than you want to see, and I've told the
wireless folks under no uncertain terms that they must severely scale
back the extent of the fixes they are submitting this late in the
game.
Anyways:
1) vmxnet3's netpoll doesn't perform the equivalent of an ISR, which
is the correct implementation, like it should. Instead it does
something like a NAPI poll operation. This leads to crashes.
From Neil Horman and Arnd Bergmann.
2) Segmentation of SKBs requires proper socket orphaning of the
fragments, otherwise we might access stale state released by the
release callbacks.
This is a 5 patch fix, but the initial patches are giving
variables and such significantly clearer names such that the
actual fix itself at the end looks trivial.
From Michael S. Tsirkin.
3) TCP control block release can deadlock if invoked from a timer on
an already "owned" socket. Fix from Eric Dumazet.
4) In the bridge multicast code, we must validate that the
destination address of general queries is the link local all-nodes
multicast address. From Linus Lüssing.
5) The x86 BPF JIT support for negative offsets puts the parameter
for the helper function call in the wrong register. Fix from
Alexei Starovoitov.
6) The descriptor type used for RTL_GIGA_MAC_VER_17 chips in the
r8169 driver is incorrect. Fix from Hayes Wang.
7) The xen-netback driver tests skb_shinfo(skb)->gso_type bits to see
if a packet is a GSO frame, but that's not the correct test. It
should use skb_is_gso(skb) instead. Fix from Wei Liu.
8) Negative msg->msg_namelen values should generate an error, from
Matthew Leach.
9) at86rf230 can deadlock because it takes the same lock from it's
ISR and it's hard_start_xmit method, without disabling interrupts
in the latter. Fix from Alexander Aring.
10) The FEC driver's restart doesn't perform operations in the correct
order, so promiscuous settings can get lost. Fix from Stefan
Wahren.
11) Fix SKB leak in SCTP cookie handling, from Daniel Borkmann.
12) Reference count and memory leak fixes in TIPC from Ying Xue and
Erik Hugne.
13) Forced eviction in inet_frag_evictor() must strictly make sure all
frags are deleted, otherwise module unload (f.e. 6lowpan) can
crash. Fix from Florian Westphal.
14) Remove assumptions in AF_UNIX's use of csum_partial() (which it
uses as a hash function), which breaks on PowerPC. From Anton
Blanchard.
The main gist of the issue is that csum_partial() is defined only
as a value that, once folded (f.e. via csum_fold()) produces a
correct 16-bit checksum. It is legitimate, therefore, for
csum_partial() to produce two different 32-bit values over the
same data if their respective alignments are different.
15) Fix endiannes bug in MAC address handling of ibmveth driver, also
from Anton Blanchard.
16) Error checks for ipv6 exthdrs offload registration are reversed,
from Anton Nayshtut.
17) Externally triggered ipv6 addrconf routes should count against the
garbage collection threshold. Fix from Sabrina Dubroca.
18) The PCI shutdown handler added to the bnx2 driver can wedge the
chip if it was not brought up earlier already, which in particular
causes the firmware to shut down the PHY. Fix from Michael Chan.
19) Adjust the sanity WARN_ON_ONCE() in qdisc_list_add() because as
currently coded it can and does trigger in legitimate situations.
From Eric Dumazet.
20) BNA driver fails to build on ARM because of a too large udelay()
call, fix from Ben Hutchings.
21) Fair-Queue qdisc holds locks during GFP_KERNEL allocations, fix
from Eric Dumazet.
22) The vlan passthrough ops added in the previous release causes a
regression in source MAC address setting of outgoing headers in
some circumstances. Fix from Peter Boström"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (70 commits)
ipv6: Avoid unnecessary temporary addresses being generated
eth: fec: Fix lost promiscuous mode after reconnecting cable
bonding: set correct vlan id for alb xmit path
at86rf230: fix lockdep splats
net/mlx4_en: Deregister multicast vxlan steering rules when going down
vmxnet3: fix building without CONFIG_PCI_MSI
MAINTAINERS: add networking selftests to NETWORKING
net: socket: error on a negative msg_namelen
MAINTAINERS: Add tools/net to NETWORKING [GENERAL]
packet: doc: Spelling s/than/that/
net/mlx4_core: Load the IB driver when the device supports IBoE
net/mlx4_en: Handle vxlan steering rules for mac address changes
net/mlx4_core: Fix wrong dump of the vxlan offloads device capability
xen-netback: use skb_is_gso in xenvif_start_xmit
r8169: fix the incorrect tx descriptor version
tools/net/Makefile: Define PACKAGE to fix build problems
x86: bpf_jit: support negative offsets
bridge: multicast: enable snooping on general queries only
bridge: multicast: add sanity check for general query destination
tcp: tcp_release_cb() should release socket ownership
...
If the sh_eth device is registered using OF, then the driver
should call of_mdiobus_register() to register the PHYs described
in the devicetree and then use of_phy_connect() to connect the
PHYs to the device.
This ensures that any PHYs registered in the device tree are
appropriately connected to the parent devices nodes so that
the PHY drivers can access their OF properties.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.
This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit d3ab3ffd1d
(bonding: use rlb_client_info->vlan_id instead of ->tag)
remove the rlb_client_info->tag, but occur some issues,
The vlan_get_tag() will return 0 for success and -EINVAL for
error, so the client_info->vlan_id always be set to 0 if the
vlan_get_tag return 0 for success, so the client_info would
never get a correct vlan id.
We should only set the vlan id to 0 when the vlan_get_tag return error.
Fixes: d3ab3ffd1d (bonding: use rlb_client_info->vlan_id instead of ->tag)
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_enet_netpoll does not exist, and causing
bcm63xx_net to fail to build when NET_POLL_CONTROLLER
is defined.
Remove the bogus .ndo_poll_controller = bcm_enet_netpoll
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, e1000e, ixgbe and ixgbevf.
Tom Herbert provides changes to e1000e, igb and ixgbe to call skb_set_hash()
to set the hash and its type in an skbuff.
Carolyn provides a fix for igb where using ethtool for EEE settings, which
was not working correctly.
Jacob provides some trivial cleanups and fixes for ixgbe which mainly
dealt with the file headers.
Julia Lawall provides a one fix for ixgbevf where the driver did not need
to adjust the power state on suspend, so the call to pci_set_power_state()
in the resume function was a no-op.
v2:
- dropped patches 4-6 from original series which implemented debugfs for
igb from Carolyn based on feed back from David Miller and Or Gerlitz
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
For the mac80211 bits, Johannes says:
"This time, I have a number of small fixes and improvements, and those
are fairly straight-forward. More interesting changes come from Luca
with some preparations for the CSA work, mostly around interface/channel
combinations checking. One other possibly interesting change is a small
one by myself to add NAPI support back to mac80211, which can help
improve TCP behaviour through GRO."
For the Bluetooth bits, Gustavo says:
"This is our first pull request for 3.15, the main feature here is the addition of
the privacy feature for low energy devices. Other than that we have a bunch of small
improvements, fixes, and clean ups all over the tree."
And...
"Another pull request to 3.15. Here we have the second part of the LE private
feature, the LE auto-connect feature and improvements to the power off
procedures. The rest are small improvements, clean up, and fixes."
For the iwlwifi bits, Emmanuel says:
"I have here a whole bunch of various things. Trivial cleanups,
debugfs handlers and new stuff for the new generation of devices
along with new capabilities for monitor mode. We also have support
for power save for dual interface mode, but that is not supported by
the firmware currently available."
And for the Atheros bits, Kalle says:
"For ath10k Alexander did some cleanup to PCI error cases and switched
ath10k to use pci_enable_msi_range(). Michal implemented AP CSA support
and sta_rc_update() operation. I enabled firmware "STA quick kickout"
functionality for faster detection of disappeared clients.
Also there are lots of small fixes to everywhere from various people."
I pulled the wireless tree to avoid some merge conflicts, and I
reverted the staging patch that I had mistakenly merged previously.
Along with that, mwifiex, brcmfmac, wil6210, ath9k, and a few other
drivers get their usual round of updates. Also notable is the addition
of yet another driver in the rtlwifi family.
...
I have amended this commit request to correct the build problems in
staging, including a warning added to one of the staging drivers by
the wireless-next tree. I also included a fix from Larry Finger to
address an issue found in rtl8723be by Dan Carpenter and smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit eac40d9631. It cause
random connection drops on RT5390 PCI adapters.
On Mediatek there is different driver version available for RT53xx chip
based on bus type (2.5.0.3 for PCI and 2.6.1.3 for USB). Hence possibly
we should set registers differently based on bus type. But is also
possible that new driver (i.e. 2.6.1.3) was not verified on RT53xx USB.
Until we figure out how to initialize registers properly for RT53xx just
revert commit eac40d9631 since it cause
regression.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 558ff225de (ath9k: fix
ps-poll responses under a-mpdu sessions) non-data frames would have
gotten a sequence number from a TIDs sequence counter instead of
using the global sequence counter.
This can lead to instable connections.
To fix this only select the correct TID if we are processing a
data frame. Furthermore, prevent non-data frames to get a sequence
number from a TID sequence counter by adding a check to
ath_tx_setup_buffer.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 1eb4301867 (brcmfmac: fix txglomming scatter-gather packet transfers)
added an allocation of an skb via brcmu_pkt_buf_get_skb() but forgot to
free it on one of the error paths.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Dave Jones<davej@fedoraproject.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0034b29 ("cxgb4: Don't assume LSO only uses SGL path in t4_eth_xmit()")
introduced a regression where-in length was calculated wrongly for LSO path,
causing chip hangs.
So, correct the calculation of len.
Fixes: 0034b29 ("cxgb4: Don't assume LSO only uses SGL path in t4_eth_xmit()")
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'd come in with SGE_FL_BUFFER_SIZE[0] and [1] both equal to 64KB and the
extant logic would flag that as an error.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a619d1abe2 leads to the following static checker warning:
drivers/net/wireless/rtlwifi/rtl8723be/phy.c:667 _rtl8723be_store_tx_power_by_rate()
error: buffer overflow 'rtlphy->tx_power_by_rate_offset[band]' 4 <= 5
This warning arises because the code is testing the indices for the wrong maximum
values. In addition, the tests merely putput a warning, and then procedes to
corrupt memory. With this change, any such invalid memory access is avoided.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mlx4_en_stop_port() is called, we need to deregister also the
tunnel steering rules that relate to multicast.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit d25f06ea46 "vmxnet3: fix netpoll race condition",
the vmxnet3 driver fails to build when CONFIG_PCI_MSI is disabled,
because it unconditionally references the vmxnet3_msix_rx()
function.
To fix this, use the same #ifdef in the caller that exists around
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not need to adjust the power state on suspend, so the
call to pci_set_power_state in the resume function is a no-op. Drop it,
to make the code more understandable.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes some formatting on multilined print messages, so that
the text of the print appears on a single line, which aids in grepping
the sourcecode for where the error came from.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The header above this function did not match the function prototype.
This patch rewords the comment to specify the correct parameters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the contact information on the ixgbe driver files so
that every file includes the Linux NICS address, as it is still used,
but only a few of the files mentioned it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
cppcheck detected following warning in ixgbe_fcoe.c
(warning) %d in format string (no. 1) requires 'int' but the
argument type is 'unsigned int'.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where using ethtool for EEE setting was not
working correctly. This patch also fixes a problem where
the function that checks for EEE status on i354 devices was not being
called and was causing warnings with static analysis tools.
Reported-by: Rashika Kheria <rashika.kheria@gmail.com>
Reported-by: Josh Triplett <josh@joshtriplett.org>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
netpoll can call functions in hard irq context that are ordinarily
called in lesser contexts. For those functions use dev_kfree_skb_any
and dev_consume_skb_any so skbs are freed safely from hard irq
context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as
which can be called in hard irq by netpoll, softirq context
by normal napi polling, and in normal sleepable context
by the network device close method.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb with dev_kfree_skb_any in cp_start_xmit
as it can be called in both hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added by user, adapter->vlans_added is incremented.
But if the VLAN is already programmed in HW, driver ends up
incrementing the counter wrongly.
Increment the counter only if VLAN is not already programmed in the HW.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver creates only a single TXQ on any BE3-R multi-channel
interface.
This patch changes this and creates multiple TXQs on RSS-capable multi-channel
BE3-R interfaces. This change helps improve the TX pps performance on the
affected interface.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocation size must be be_max_uc() and not "be_max_uc() + 1"
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to control VF's link state by implementing the
ndo_set_vf_link_state() hook.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GET_PROFILE_CONFIG_V1 cmd even for BE3-R (it's already used for
Lancer-R and Skyhawk-R), to query max-vfs value supported by the FW.
This is needed as on some configs, the value exported in the PCI-config
space is not accurate.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking what protocol drivers to load, the IB driver should be
requested also over Ethernet ports, if the device supports IBoE (RoCE).
Fixes: b046ffe 'net/mlx4_core: Load higher level modules according to ports type'
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device mac address is changed, we must deregister the vxlan
steering rule associated with the previous mac, and register a new
steering rule using the new mac.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the value used to dump the vxlan offloads device capability to align
with the MLX4_DEV_CAP_FLAG2_yyy definition. While on that, add dump to
the IPoIB flow-steering device capability and fix small typo.
The vxlan cap value wasn't fully handled when a conflict was resolved
between MLX4_DEV_CAP_FLAG2_DMFS_IPOIB coming from the IB tree to
MLX4_DEV_CAP_FLAG2_VXLAN_OFFLOADS coming from net-next.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To activate RoCE/SRIOV, need to remove the following:
1. In mlx4_ib_add, need to remove the error return preventing
initialization of a RoCE port under SRIOV.
2. In update_vport_qp_params (in resource_tracker.c) need to remove
the error return when a RoCE RC or UD qp is detected.
This error return causes the INIT-to-RTR qp transition to fail
in the wrapper function under RoCE/SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.
To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.
This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.
Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.
The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified: INIT-to-RTR, and SQD-to-SQD.
Similarly for the alternate path information.
Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.
For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
MAC information to the operational information, and reset
the candidate MAC info.
2. If there was a previous MAC, unregister it. Then move
the MAC information from candidate to operational, and
reset the candidate info (as in 1. above).
The MAC address failure logic is the same for all cases:
- Unregister the candidate MAC, and reset the candidate MAC info.
For Vlan registration, the logic is similar.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IB transport, the host determines the slave GIDs. For ETH (RoCE),
however, the slave's GID is determined by the IP address that the slave
itself assigns to the ETH device used by RoCE.
In this case, the slave must be able to write its GIDs to the HCA gid table
(at the GID indices that slave "owns").
This commit adds processing for the SET_PORT_GID_TABLE opcode modifier
for the SET_PORT command wrapper (so that slaves may modify their GIDS
for RoCE).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 5bd076708 ("Xen-netback: Fix issue caused by using gso_type wrongly")
we use skb_is_gso to determine if we need an extra slot to accommodate
the SKB. There's similar error in interface.c. Change that to use
skb_is_gso as well.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv is not instantiated at gfar_of_init() time, when
parsing the DT for info on supported HW queues. Before
the netdev can be allocated, the number of supported
queues must be known. Because the number of supported
queues depends on device type, move the compatibility
checks before netdev allocation. Local vars are used
to hold the operation mode info before netdev allocation.
This fixes the null accesses for priv->.., in gfar_of_init.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx descriptor version of RTL8111B belong to RTL_TD_0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rf233 and rf231 are sufficiently similar that we can treat
rf233 like rf231.
rf233 is missing some features that rf231 has, but we don't currently
make use of them so there's nothing to handle differently yet.
Should we add support in the future for rf231 *_NOCLK or SLEEP states,
or PAD_IO drive strength, exceptions will need to be made for rf233.
Signed-off-by: Thomas Stilwell <stilwellt@openlabs.co>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option code is taking IP address and putting it into a generic
container. Force cast to silence sparse warnings.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.
Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3's netpoll driver is incorrectly coded. It directly calls
vmxnet3_do_poll, which is the driver internal napi poll routine. As the netpoll
controller method doesn't block real napi polls in any way, there is a potential
for race conditions in which the netpoll controller method and the napi poll
method run concurrently. The result is data corruption causing panics such as this
one recently observed:
PID: 1371 TASK: ffff88023762caa0 CPU: 1 COMMAND: "rs:main Q:Reg"
#0 [ffff88023abd5780] machine_kexec at ffffffff81038f3b
#1 [ffff88023abd57e0] crash_kexec at ffffffff810c5d92
#2 [ffff88023abd58b0] oops_end at ffffffff8152b570
#3 [ffff88023abd58e0] die at ffffffff81010e0b
#4 [ffff88023abd5910] do_trap at ffffffff8152add4
#5 [ffff88023abd5970] do_invalid_op at ffffffff8100cf95
#6 [ffff88023abd5a10] invalid_op at ffffffff8100bf9b
[exception RIP: vmxnet3_rq_rx_complete+1968]
RIP: ffffffffa00f1e80 RSP: ffff88023abd5ac8 RFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff88023b5dcee0 RCX: 00000000000000c0
RDX: 0000000000000000 RSI: 00000000000005f2 RDI: ffff88023b5dcee0
RBP: ffff88023abd5b48 R8: 0000000000000000 R9: ffff88023a3b6048
R10: 0000000000000000 R11: 0000000000000002 R12: ffff8802398d4cd8
R13: ffff88023af35140 R14: ffff88023b60c890 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88023abd5b50] vmxnet3_do_poll at ffffffffa00f204a [vmxnet3]
#8 [ffff88023abd5b80] vmxnet3_netpoll at ffffffffa00f209c [vmxnet3]
#9 [ffff88023abd5ba0] netpoll_poll_dev at ffffffff81472bb7
The fix is to do as other drivers do, and have the poll controller call the top
half interrupt handler, which schedules a napi poll properly to recieve frames
Tested by myself, successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: stable@vger.kernel.org
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now define the priority against BT per AC. This is
possible with a newer firmware that allows to define the
priority with 2 bits.
Note that this change is compatible with older firmware
since older firmware will simply ignore the new bit (11),
and we still set the old bit (12) in the same cases as
before.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This code is really related to BT Coex - move it to the coex
file.
Also - prepare for a FW API change that will happen soon:
Bits 11 and 12 will be allocated for BT priority. Today, we
only have bit 12.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
7265 features a new calibration which is called antenna
coupling. The purpose of this calibration (which isn't
really a calibration), is to measure the isolation between
the antennas and that can give us useful information for
the Coex modules.
With this information, we can tune the LookUpTables (LUTs)
that define the BT / WiFi contention policy.
The LUTs currently contain dummy values - but they will be
updated soon.
While at it, change the current code to stop duplicate the
host command while sending. This was needed back then, when
the command was short enough to be allocated on the stack.
Since then, the command grew a lot and is now allocated on
the heap - hence we can use the NOCOPY option instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is a flow in which we send the host command in SYNC
mode, but we don't take priv->mutex.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1046495
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Call skb_cow_head() before editing the tx packet header. The header
would be reallocated if it is shared.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current netback uses gso_type to check whether the skb contains
gso offload, and this is wrong. Gso_size is the right one to
check gso existence, and gso_type is only used to check gso type.
Some skbs contains nonzero gso_type and zero gso_size, current
netback would treat these skbs as gso and create wrong response
for this. This also causes ssh failure to domu from other server.
V2: use skb_is_gso function as Paul Durrant suggested
Signed-off-by: Annie Li <annie.li@oracle.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using an own copy of struct net_device_stats in struct
cpsw_priv, use stats from struct net_device. Also remove the thus
unnecessary .ndo_get_stats function, as it just returns dev->stats,
which is the default.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a bug in the Hyper-V host verion 2008R2, we need to use a slightly smaller
receive buffer size, otherwise the buffer will not be accepted by the legacy hosts.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udelay() does not work on some architectures for values above
2000, in particular on ARM:
ERROR: "__bad_udelay" [drivers/net/ethernet/brocade/bna/bna.ko] undefined!
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable segmentation offload.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable send side checksum offload.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable receive side checksum offload.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to enabling guest side offloads, enable the offloads on the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for enabling offloads, cleanup the send path.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the code and enable scatter gather I/O.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver reads the mac address from the device registers which would
need to have been programmed by the bootloader. This patch adds
the ability to pull the mac from devicetree via the pci device dt node.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Changes since v2:
- eliminated use of stack tmpaddr per feedback
Changes since v1:
- simplified based on feedback
- fixed formatting
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to mlx5_health_cleanup() in the module init function can never
be reached. Removing it.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of fixes intende for the 3.14 stream...
For the mac80211 bits, Johannes says:
"Here I have a fix from Eliad for the minimal channel width calculation
in the mac80211 code which lead to monitor mode not working at all for
drivers using that. One of my fixes is for an issue noticed by Michal,
we clear an already cleared value but do it without locking, so just
remove that. The other is for a data leak - we leak two bytes of kernel
memory out over the air in QoS NULL frames because those don't get a
sequence number assigned in the TX path."
For the iwlwifi bits, Emmanuel says:
"One more fix and an update for device IDs.
There is a bugzilla reported for the fix which is mentioned in the commit message."
Along with those...
Amitkumar Karwar provides two mwifiex fixes, both correcting some
data transcription problems.
Ivaylo Dimitrov uses skb_trim in the wl1251 driver to avoid
HAVE_EFFICIENT_UNALIGNED_ACCESS problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Faster than memcpy/memset on some architectures.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the "fsl,etsec2" compatible models the driver currently
supports 8 Tx and Rx DMA rings (aka HW queues). However, there
are only 2 pairs of Rx/Tx interrupt lines, as these controllers
are integrated in low power SoCs with 2 CPUs at most. As a result,
there are at most 2 NAPI instances that have to service multiple
Tx and Rx queues for these devices. This complicates the NAPI
polling routine having to iterate over the mutiple Rx/Tx queues
hooked to the same interrupt lines. And there's also an overhead
at HW level, as the controller needs to service all the 8 Tx rings
in a round robin manner. The combined overhead shows up for multi
parallel Tx flows transmitted by the kernel stack, when the driver
usually starts returning NETDEV_TX_BUSY leading to NETDEV WATCHDOG
Tx timeout triggering if the Tx path is congested for too long.
As an alternative, this patch makes the driver support only one
Tx/Rx DMA ring per NAPI instance (per interrupt group or pair
of Tx/Rx interrupt lines) by default. The simplified single queue
polling routine (gfar_poll_sq) will be the default napi poll routine
for the etsec2 devices too. Some adjustments needed to be made to
link the Tx/Rx HW queues with each NAPI instance (2 in this case).
The gfar_poll_sq() is already successfully used by older SQ_SG_MODE
(single interrupt group) controllers.
This patch fixes Tx timeout triggering under heavy Tx traffic load
(i.e. iperf -c -P 8) for the "fsl,etsec2" (currently the only
MQ_MG_MODE devices). There's also a significant memory footprint
reduction by supporting 2 Rx/Tx DMA rings (at most), instead of 8,
for these devices.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some concurrency issues on devices w/ 2 CPUs related
to the handling of Rx and Tx interrupts. eTSEC has separate
interrupt lines for Rx and Tx but a single imask register
to mask these interrupts and a single NAPI instance to handle
both Rx and Tx work. As a result, the Rx and Tx ISRs are
identical, both are invoking gfar_schedule_cleanup(), however
both handlers can be entered at the same time when the Rx and
Tx interrupts are taken by different CPUs. In this case
spurrious interrupts (SPU) show up (in /proc/interrupts)
indicating a concurrency issue. Also, Tx overruns followed
by Tx timeout have been observed under heavy Tx traffic load.
To address these issues, the schedule cleanup ISR part has
been changed to handle the Rx and Tx interrupts independently.
The patch adds a separate NAPI poll routine for Tx cleanup to
be triggerred independently by the Tx confirmation interrupts
only. Existing poll functions are modified to handle only
the Rx path processing. The Tx poll routine does not need a
budget, since Tx processing doesn't consume NAPI budget, and
hence it is registered with minimum NAPI weight.
NAPI scheduling does not require locking since there are
different NAPI instances between the Rx and Tx confirmation
paths now.
So, the patch fixes the occurence of spurrious Rx/Tx interrupts.
Tx overruns also occur less frequently now.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI regressions
we have been having on some types of devices. The other two are quirks
for some Logitech video devices.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMbu0sACgkQMUfUDdst+yl/MgCeJbq5Lre/M59O5YVWhS3fghsG
PisAoI7t2LLnhiC/DwZD10vs2hEkZxw2
=R/Qt
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI
regressions we have been having on some types of devices. The other
two are quirks for some Logitech video devices"
* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e
The pci shutdown handler added in:
bnx2: Add pci shutdown handler
commit 25bfb1dd4b
created a shutdown down sequence without chip reset if the device was
never brought up. This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive. On some
systems, it may generate NMI in the bnx2's pci shutdown handler.
The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A scheduled scan is a more persistent setting and should take priority
over temporary regular scans. Abort the regular when a sched_scan
request arrives and then request the sched_scan.
The kernel API allows sending a sched_scan without canceling a regular
scan in progress, so this is our way to abstract the FW's limitations.
Make the scan-cancel Rx handler async and flush after invocation to
ensure new scans can't creep in before it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
cfg80211 assumes a scheduled scan is stopped synchronously. Wait for the
FW before returning to caller.
Don't do anything in the async handler in the stop-from-above flow.
There's no need to call the mac80211 sched-scan completion as the
cleanup will be automatic. Make sure the async handler is called before
the next incoming scan changes the scan_status by flushing the async
handlers after all invocations.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Check for both cfg->d0i3 and fw d0i3 support in order
to enable d0i3 support.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
BGN SKU won't scan on 5.2GHz obviously, but the firmware
still expects the driver to reserve space for the the probe
request for the 5.2GHz band.
Fix this by allocating space and leave it empty.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69541
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When indicating RF-kill toggle to the higher layer, that
may in turn call back to the transport (for MVM at least)
to turn off the device quickly. Instead of that, allow it
to return whether or not the device should be turned off,
this gets rid of the call indirection and will help make
the API more consistent when we go back to non-threaded
interrupts again for PCIe.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
1. Enable LP XTAL to avoid HW bug where device may consume much
power if FW is not loaded after device reset. LP XTAL is
disabled by default after device HW reset. Configure device's
"persistence" mode to avoid resetting XTAL again when SHRD_HW_RST
occurs in S3.
2. Add methods to access SHR (shared block memory space) directly from PCI
bus w/o need to power up MAC HW.
Shared internal registers (e.g. SHR_APMG_GP1, SHR_APMG_XTAL_CFG)can be
accessed directly from PCI bus through SHR arbiter even when MAC HW is
powered down. This is possible due to indirect read/write via
HEEP_CTRL_WRD_PCIEX_CTRL (0xEC) and HEEP_CTRL_WRD_PCIEX_DATA (0xF4)
registers.
Use iwl_write32()/iwl_read32() family to access these registers. The MAC HW
need not be powered up so no "grab inc access" is required.
For example, to read from SHR_APMG_GP1 register (0x1DC),
first, write to the control register:
HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register)
HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 2 (read access)
second, read from the data register HEEP_CTRL_WRD_PCIEX_DATA[31:0].
To write the register, first, write to the data register
HEEP_CTRL_WRD_PCIEX_DATA[31:0] and then:
HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register)
HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 3 (write access)
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When power update is initiated on BSS STA while P2P client
exists, the power command will be sent only on BSS STA vif
ignoring P2P client.
Since the firmware has symmetric constraints on the power
save enablement we can simplify the code a bit.
The current firmware doesn't know how to enable power
management on P2P client. Even BSS power management must
be disabled when a P2P client is added.
Future firmware will support power save on BSS and P2P client
as long as they are on different channels.
This was buggy since we didn't disable power management on
P2P client interface if BSS added on the same channel.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As the antenna dependent fields depend on the firmware file and not
the NVM, use those fields in the VHT capability creation.
Additionally, fix the STBC and antenna pattern consistency fields.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New firmware enforce valid values for the quota in D3.
The values given to the firmware when suspending and using
WoWLAN where dummy - change them to realistics values.
Tested-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Switch pos to char * which makes the code a bit shorter
as well as other minor cleanups suggested by Joe Perches.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This message triggers on systems that don't support the API,
so suppress them when not debugging as it's not useful to
see it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Otherwise lockdep complains about the lock, I'm not sure
why we didn't see this before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix warning about code defined but never used if IGB_HWMON not defined.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ARRAY_SIZE for array size calculation.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb->pkt_type is not a bitmask, but contains only value at a time from
the range defined in include/uapi/linux/if_packet.h.
Checking it like if it was a bitmask of values would also cause
PACKET_OTHERHOST, PACKET_LOOPBACK and PACKET_FASTROUTE to be matched by
this check since their lower 2 bits are also set, although that does not
fix a real bug, it is still potentially confusing.
This bogus check was introduced in commit 815cccbf ("ixgbe: add setlink,
getlink support to ixgbe and ixgbevf").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous commit c3a0dce35a fixed an overrun for the RAR on i218 devices.
This commit also attempted to homogenize the RAR/SHRA access for all parts
accessed by the e1000e driver. This change introduced an error for
assigning MAC addresses to guest OS's for 82579 devices.
Only RAR[0] is accessible to the driver for 82579 parts, and additional
addresses must be placed into the SHRA[L|H] registers. The rar_entry_count
was changed in the previous commit to an inaccurate value that accounted
for all RAR and SHRA registers, not just the ones usable by the driver.
This patch fixes the count to the correct value and adjusts the
e1000_rar_set_pch2lan() function to user the correct index.
Cc: John Greene <jogreene@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes to the rar_entry_count value require a change to the indexing
used to access the SHRA[H|L] registers when testing them with
'ethtool -t <iface> offline'
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Valid values for InterruptThrottleRate are 10-100000, or one of
0, 1, 3, 4. '2' is not valid. This is a legacy from the branching
from the e1000 driver code that e1000e was based from.
Prior to this patch, if the e1000e driver was loaded with a forced
invalid InterruptThrottleRate of '2', then no throttle rate would be
set and no error message generated.
Now, a message will be generated that an invalid value was used and the
value for InterruptThrottleRate will be set to the default value.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ULP is a power saving feature that reduces the power consumption of the
PHY when a cable is not connected.
ULP is gated on the following conditions:
1) The hardware must support ULP. Currently this is only I218
devices from Intel
2) ULP is initiated by the driver, so, no driver results in no ULP.
3) ULP's implementation utilizes Runtime Power Management to toggle its
execution. ULP is enabled/disabled based on the state of Runtime PM.
4) ULP is not active when wake-on-unicast, multicast or broadcast is active
as these features are mutually-exclusive.
Since the PHY is in an unavailable state while ULP is active, any access
of the PHY registers will fail. This is resolved by utilizing kernel
calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync)
and then, after PHY access is complete, allow the device to resume
Runtime PM (e.g. pm_runtime_put_sync).
Under certain conditions, toggling the LANPHYPC is necessary to disable
ULP mode. Break out existing code to toggle LANPHYPC to a new function
to avoid code duplication.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix issues with:
RuntimePM causing the device to repeatedly flip between suspend and resume
with the interface administratively downed.
Having RuntimePM enabled interfering with the functionality of Energy
Efficient Ethernet.
Added checks to disallow functions that should not be executed if the
device is currently runtime suspended
Make runtime_idle callback to use same deterministic behavior as the igb
driver.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the system power management flows to prevent the suspend path from
being executed twice when hibernating since both the freeze and
poweroff callbacks were set to e1000_suspend() via SET_SYSTEM_SLEEP_PM_OPS.
There are HW workarounds that are performed during this flow and calling
them twice was causing erroneous behavior.
Re-arrange the code to take advantage of common code paths and explicitly
set the individual dev_pm_ops callbacks for suspend, resume, freeze,
thaw, poweroff and restore.
Add a boolean parameter (reset) to the e1000e_down function to allow
for cases when the HW should not be reset when downed during a PM event.
Now that all suspend/shutdown paths result in a call to __e1000_shutdown()
that checks Wake on Lan status, removing redundant check for WoL in
e1000_power_down_phy().
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Branding strings from recently released and soon to be released
hardware configurations that are supported by e1000e.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is to update the GPL header by removing the portion that
refers to the Free Software Foundation address.
Change the copyright date for 2014.
Reformat the header comments to conform to kernel networking coding norms
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling EEE LPI sooner than one second after link up on 82579 causes link
issues with some switches.
Remove EEE enablement for 82579 parts from the link initialization flow to
avoid initializing too early. EEE initialization for 82579 will be done
in e1000e_update_phy_task.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On a ME enabled system with the cable out, the driver init flow would
generate an erroneous message indicating that resets were being blocked
by an active ME session. Cause was ME clearing the semaphore bit to
block further PHY resets for up to 50 msec during power-on/cycle. After
this interval, ME would re-set the bit and allow PHY resets.
To resolve this, change the flow of e1000e_phy_hw_reset_generic() to
utilize a delay and retry method. Poll the FWSM register to minimize
any extra time added to the flow. If the delay times out at 100ms
(checked in 10msec increments), then return the value E1000_BLK_PHY_RESET,
as this is the accurate state of the PHY. Attempting to alter just the
call to e1000e_phy_hw_reset_generic() in e1000_init_phy_workarounds_pchlan()
just caused the problem to move further down the flow.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleaning up some pointer references that are no longer necessary
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add lock in e1000e_phc_adjfreq to prevent concurrent changes to TIMINCA
and SYSTIMH/L.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlMZkPoACgkQjTAFq1RaXHOWwgCeMnz0WCV7WtUDnm3FY8ViwaNv
q9kAn0HgLK6Igi1rn96/MpdkRA2OaN7E
=Ralk
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.15-20140307' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2014-02-12
this is a pull request of twelve patches for net-next/master.
Alexander Shiyan contributes two patches for the mcp251x, one making
the driver more quiet and the other one improves the compile time
coverage by removing the #ifdef CONFIG_PM_SLEEP. Then two patches for
the flexcan driver by me, one removing the #ifdef CONFIG_PM_SLEEP, too,
the other one making use of platform_get_device_id(). Another patch by
me which converts the janz-ican3 driver to use netdev_<level>(). The
remaining 7 patches are by Oliver Hartkopp, they add CAN FD support to
the netlink configuration interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support hw IPv6 checksum for TCP and UDP packets.
Note that the hw has the limitation of the range of the transport
offset. Besides, the TCP Pseudo Header of the IPv6 TSO of the hw
bases on the Microsoft document which excludes the packet length.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support scatter gather and TSO.
Adjust the tx checksum function and set the max gso size to fix the
size of the tx aggregation buffer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue dealing with the remain rx packets, even though the allocation
of the skb fail. This could calculate the correct dropped packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan