MMCIF on sh73a0 doesn't support Command Completion Signal, a platform
parameter has to be added to disable it on kzm9g.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MMCIF on r8a7740 doesn't support Command Completion Signal, a platform
parameter has to be added to disable it on armadillo800eva.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MMCIF on r8a73a4 doesn't support Command Completion Signal, a platform
parameter has to be added to disable it on ape6evm.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bock-W USB1 (CN29) can be USB Host/Func by SW98/SW99 settings.
USB Func will be enabled if CONFIG_USB_RENESAS_USBHS_UDC[_MODULE]
was selected on this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Koelsch base board support making use of 2 GiB of memory,
the r8a7791 SoC with the SCIF0 serial port and CA15 with
CMT timer.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready SMP/PFC]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables R-Car sound,
AK4643 (CN19) and AK4554 (CN20/CN21) codec chip
on Bock-W.
But, it supports PIO transfer only at this point.
User can check sound settings (Dip-switch/PFC etc)
via this patch, but will get under/over flow error
when playback/capture.
Because PIO transfer via SSI will be interrupted
"sampling rate" times per 1 second.
DMA transfer will be supported when HPB-DMAC was
enabled on r8a7778.
You will notice strange ALSA sound card HW
numbering on Bock-W board.
This came from AK4554 strange format on playback/capture.
The format on playback/capture is same on "normal" codec chip,
but AK4554 was different.
Because of that, AK4554 playback/capture are
registered as a different sound card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: squashed cleanup of SND_SOC_xxx in
Kconfig by Kuninori Morimoto]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables global use of FPGA,
since it will be used from many devices.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU device erroneously receives the DU resources array as platform
data instead of the DU platform data structure. Fix it.
This problem was introduced by f631fa0 ("ARM: shmobile: lager: Add Display
Unit support").
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently a dummy fixed always-on regulator is used for all 3 SD/MMC
interfaces on ape6evm. This patch updates the board to use correct supplies
for MMC0, SDHI0 and SDHI1 VDD. SDHI0 VccQ supply regulator should be
implemented in a separate patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only the VGA output is currently supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Platform data and resources for Lager devices are kmemdup()ed when the
corresponding devices are registered and can thus be declared as const.
Do so.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Support the DU0 VGA and DU1 LVDS outputs. DU1 is connected to a
Mitsubishi AA104XD12 panel (10.4" XGA).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
USB phy initialisation function is needed from not only
USB Host but also USB Function too.
This patch adds usb phy common control function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7791 CMT support via channel 0 of CMT0. At this
point the CMT is used for clock event operation, but in
the future the arch timer will be the main timer and the
CMT will be used for deep sleep wake up only.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit a7663b88280d00359715817620798e99d54d401c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SCIF serial port support to the r8a7791 SoC by
adding platform devices for SCIFA0 -> SCIFA5 as well
as SCIFB0 -> SCIFB2 and SCIF0 -> SCIF5 together with
clock bindings. DT device description is excluded at
this point since such bindings are still under
development.
Signed-off-by: Yoshikazu Fujikawa <yoshikazu.fujikawa.ue@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped holes in enum]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r8a7791 SoC including:
- Single Cortex-A15 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready code]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7778_register_hspi() used only from setup-r8a7778.c
it can be static
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sh_eth driver which needs platform data at the time of
registration is used from BockW only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
vin driver which needs platform data at the time of
registration is used from BockW only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
e5c9b4cd66 ("sh_eth: get R8A7740 support
out of #ifdef") exchanged sh-eth driver name to r8a7740-gether, but,
eva_pinctrl_map[] didn't follow it. Fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently on the Lager board NFS timeouts/delays are seen when booting. That
turned out to happen because the SoC's ETH_LINK signal turns on and off after
each packet. It is connected to Micrel KSZ8041 PHY's LED0 signal. Ether LEDs
on the Lager board are named LINK and ACTIVE which corresponds to non-default
01 setting of the PHY control register 1 bits 14-15. The 'sh_eth' driver resets
the PHY when opening the network device, so we have to set the mentioned bits
back to 01 from the default 00 value which causes bouncing of ETH_LINK. That
can be achieved using the PHY platform fixup mechanism if we also modify the
driver to use it..
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce shmobile_boot_size that can be used by
future SMP code to determine the size of the boot
code that needs to be copied to internal SRAM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Expose shmobile_invalidate_start() in common.h for
mach-shmobile. This function will be used for boot of
secondary processors on future non-SCU SMP platforms.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove shmobile_smp_init_cpus() since all SMP platforms in
mach-shmobile now rely on DT for CPU core description instead
of for instance determining number of cores from the SCU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use shmobile_smp_cpu_disable() on sh73a0 since it
allows CPU Hotplug of any CPU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce the shared CPU Hotplug function shmobile_smp_cpu_disable()
for mach-shmobile. It is useful for the case when all CPUs may be
hotplugged, including CPU 0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a platform clock for the r8a7778 SRU/SSI sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU device will be called rcar-du-r8a7779. Rename the clock lookup
entry accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Platform data and resources for core devices are kmemdup()ed when the
corresponding devices are registered and can thus be declared as const.
Do so.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rename r8a7790_init_delay() into r8a7790_init_early()
to make the function name show that more than just
delay setup may happen in the future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rename r8a73a4_init_delay() into r8a73a4_init_early()
to make the function name show that more than just
delay setup may happen in the future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently all clkdev registration use "cpufreq-cpu0.0" as dev_id
for cpu clock which refers to virtual platform device. It needs to
be "cpu0" instead which is actual cpu0 device id.
This patch changes the dev_id from "cpufreq-cpu0.0" to "cpu0".
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As of 8d3214c ("sh_eth: remove 'register_type' field from 'struct
sh_eth_plat_data'") is is no longer necessary or correct to use the
'register_type' field from 'struct sh_eth_plat_data' and doing so results
in a build error.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Update early timer initialisation order of r8a7779 SoC
This resolves a regression introduced by
a894fcc2d0 ("ARM: smp_twd: Divorce smp_twd
from local timer API").
This problem was introduced in v3.10-rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=R9vg
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes3-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Third Round of Renesas ARM based SoC fixes for v3.12
* Update early timer initialisation order of r8a7779 SoC
This resolves a regression introduced by
a894fcc2d0 ("ARM: smp_twd: Divorce smp_twd
from local timer API").
This problem was introduced in v3.10-rc2.
* tag 'renesas-fixes3-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Update early timer initialisation order
Signed-off-by: Olof Johansson <olof@lixom.net>
Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization
Conflicts: Too many. Most of these are because Simon chose to send
some board updates through the V4L tree that ends up colliding with
the main platform changes. We'll work with him on sorting out his
workflow:
- arch/arm/boot/dts/r8a7740.dtsi:
- Add/add conflict in a devicetree file (keep both)
- arch/arm/mach-shmobile/Makefile:
- Splitting out of clock files collides with intc move to DT.
Keep HEAD version but remove intc-* files for R8A7740 and R8A7779.
- arch/arm/mach-shmobile/board-bockw.c:
- Keep HEAD but remove i2c, hspi and mmc device init calls
- arch/arm/mach-shmobile/board-marzen.c
- Remove mach/hardware.h include and r8a7779_add_usb_phy_device() call,
everything else stays.
- arch/arm/mach-shmobile/include/mach/r8a7778.h:
- From HEAD, Keep camera-rcar.h include and r8a7778_add_vin_device()
- From branch, keep everything
- arch/arm/mach-shmobile/include/mach/r8a7779.h:
- From HEAD, Keep only camera-rcar.h include and r8a7779_add_vin_device()
- arch/arm/mach-shmobile/setup-r8a7778.c
- Keep HEAD, but drop the MMC section (struct resource + add_mmc_device())
- take the new function name from our side (r8a7778_add_dt_devices())
- arch/arm/mach-shmobile/setup-r8a7779.c
- Keep HEAD, but drop r8a7779_add_usb_phy_device()
I've also pushed a test-merge2 branch where you can see how I resolved
them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Fagt
-----END PGP SIGNATURE-----
Merge tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Renesas SoC cleanup, refactoring and more SMP support from Kevin Hilman:
"Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization"
* tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
ARM: shmobile: Per-CPU SMP boot / sleep code for SCU SoCs
ARM: shmobile: Introduce per-CPU SMP boot / sleep code
ARM: shmobile: Use shared SCU CPU Hotplug code on r8a7779
ARM: shmobile: Use shared SCU CPU Hotplug code on sh73a0
ARM: shmobile: Add shared SCU CPU Hotplug code
ARM: shmobile: Use shared SCU SMP boot code on emev2
ARM: shmobile: Use shared SCU SMP boot code on r8a7779
ARM: shmobile: Use shared SCU SMP boot code on sh73a0
ARM: shmobile: Introduce shared SCU SMP boot code
ARM: shmobile: sh73a0: Remove global GPIO_NR definition
ARM: shmobile: kzm9d: remove nfsroot settings from bootargs
ARM: shmobile: armadillo800eva: remove nfsroot settings from bootargs
ARM: shmobile: r8a7779: move r8a7779_init_irq_xxx() to setup
ARM: shmobile: r8a7740: move r8a7740_init_irq_of() to setup
ARM: shmobile: bockw: add missing __initdata
ARM: shmobile: r8a7790: add missing __initdata
ARM: shmobile: r8a7779: add missing __initdata
ARM: shmobile: Remove unused shmobile_init_time()
ARM: shmobile: Use clocksource_of_init() on r8a7790
ARM: shmobile: Use default ->init_time() on KZM9G DT ref
...
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
but most of this is around legacy code and board support. We've found that
platform maintainers have a hard time separating all of these out and might
move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and clocksource
setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
- New backlight drivers for backlights used on Renesas shmobile platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for others in
the same mach directory. More in 2.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=EGua
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSKhYmAAoJEIwa5zzehBx322AP/1ONYs8o8f7/Gzq6lZvTN6T3
0pBTApg6Jfioi3lwKvUAEIcsW82YKQ+UZkbW66GQH6+Ri4aZJKZHuz0+JPU67OJ4
LtSLuzVWrymy2VOOUvAnS/SXkOZw/pHhU4cLNHn1dMndhUL1Uqp9/XwuiHEQyFsP
uOkpcBtIu0EWElov0PKKZ5SWBg8JJs2vy5ydiViGelWHCrZvDDZkWzIsDcBQxJLQ
juzT4+JE+KOu7vKmfw78o6iHoCS2TBRAN9YUCajRb8Wl+out1hrTahHnDWaZ5Mce
EskcQNkJROqFbjD4k3ABN4XGTv2VDmrztIwFe0SEQ7Dz/9ypCrBGT69uI9xIqTXr
GwVRIwAUFTpMupK0gy93z1ajV3N0CXV79out9+jQNUQybYE+czp8QOyhmuc1tZx0
8fn9jlBQe9Vy6yrs39gEcE7nUwrayeyQ+6UvqqwsE2pWZabNAnCMSPX5+QIu+T/3
tQ7+jYmfFeserp1sIDOHOnxfhtW9EI6U9d1h/DUCwrsuFdkL9ha4M/vh9Pwgye98
tBdz0T4yE39AJQwwFWRkv1jcQKcGu6WqJanmvS4KRBksGwuLWxy+ewOnkz2ifS25
ZYSyxAryZRBvQRqlOK11rXPfRcbGcY0MG9lkKX96rGcyWEizgE1DdjxXD8HoIleN
R8heV6GX5OzlFLGX2tKK
=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on various
platforms as support gets added. Some of the bigger changes are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for 4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1GuI
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM platform
code for include changes so we took it through our tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1vE4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
This branch contains a handful of fixes for various platforms that
weren't serious enough to be included in late 3.11-rc releases. Most of
them are for minor cleanups and cosmetic fixes.
There's also a bit of code removal here, one board file removal for
clps711x, and removal of some legacy device creation on OMAP2+.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=S4TX
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC low-priority fixes from Olof Johansson:
"This branch contains a handful of fixes for various platforms that
weren't serious enough to be included in late 3.11-rc releases. Most
of them are for minor cleanups and cosmetic fixes.
There's also a bit of code removal here, one board file removal for
clps711x, and removal of some legacy device creation on OMAP2+"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: OMAP2: use 'int' instead of 'unsigned' for variable 'gpmc_irq_start'
ARM: OMAP2: remove useless variable 'ret'
ARM: OMAP: dma: fix error return code in omap_system_dma_probe()
ARM: OMAP2+: fix wrong address when loading PRM_FRAC_INCREMENTOR_DENUMERATOR_RELOAD
ARM: OMAP2+: am33xx-restart: trigger warm reset on omap2+ boards
ARM: OMAP2: Use a consistent AM33XX SoC option description
ARM: OMAP2+: Remove legacy device creation for McPDM and DMIC
ARM: clps711x: edb7211: Remove extra iotable_init() call
ARM: clps711x: autcpu12: Remove incorrect config checking
ARM: clps711x: Drop fortunet board support
ARM: clps711x: Remove the special name for the syscon driver
ARM: dts: Fix memory node in skeleton64.dtsi
ARM: Keystone: Convert device tree file to use IRQ defines
ARM: keystone: use #include to include skeleton.dtsi
ARM: keystone: Drop the un-necessary dsb from keystone_cpu_smc()
ARM: Keystone: No need to preserve r12 across smc call
ARM: keystone: remove redundant smp_init_cpus definition
ARM: keystone: drop useless HAVE_SCHED_CLOCK
ARM: dove: fix missing __init section of dove_mpp_gpio_mode
ARM: shmobile: armadillo800eva-reference: fix compiler warning
...
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Pull media updates from Mauro Carvalho Chehab:
"This series contains:
- Exynos s5p-mfc driver got support for VP8 encoder
- Some SoC drivers gained support for asynchronous registration
(needed for DT)
- The RC subsystem gained support for RC activity LED;
- New drivers added: a video decoder(adv7842), a video encoder
(adv7511), a new GSPCA driver (stk1135) and support for Renesas
R-Car (vsp1)
- the first SDR kernel driver: mirics msi3101. Due to some troubles
with the driver, and because the API is still under discussion, it
will be merged at staging for 3.12. Need to rework on it
- usual new boards additions, fixes, cleanups and driver
improvements"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (242 commits)
[media] cx88: Fix regression: CX88_AUDIO_WM8775 can't be 0
[media] exynos4-is: Fix entity unregistration on error path
[media] exynos-gsc: Register v4l2 device
[media] exynos4-is: Fix fimc-lite bayer formats
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
[media] v4l: vsp1: Fix mutex double lock at streamon time
[media] v4l: vsp1: Add support for RT clock
[media] v4l: vsp1: Initialize media device bus_info field
[media] davinci: vpif_capture: fix error return code in vpif_probe()
[media] davinci: vpif_display: fix error return code in vpif_probe()
[media] MAINTAINERS: add entries for adv7511 and adv7842
...
for the -rc series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MJql
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren:
Omap fixes for the merge window that are not urgent enough
for the -rc series.
* tag 'omap-for-v3.12/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2: use 'int' instead of 'unsigned' for variable 'gpmc_irq_start'
ARM: OMAP2: remove useless variable 'ret'
ARM: OMAP: dma: fix error return code in omap_system_dma_probe()
ARM: OMAP2+: fix wrong address when loading PRM_FRAC_INCREMENTOR_DENUMERATOR_RELOAD
ARM: OMAP2+: am33xx-restart: trigger warm reset on omap2+ boards
ARM: OMAP2: Use a consistent AM33XX SoC option description
ARM: OMAP2+: Remove legacy device creation for McPDM and DMIC
+ Linux 3.11-rc6
a894fcc2d0 ("ARM: smp_twd: Divorce smp_twd
from local timer API") altered twd_local_timer_common_register() so that it
may make use of late_timer_init.
This is problematic on marzen with Magnus's recent patch "ARM: shmobile:
marzen: Switch to DT_MACHINE_START" which switches marzen around to enable
USE_OF and thus shmobile_timer_init(), which is registered as
late_time_init by shmobile_earlytimer_init() stops being a no-op.
As a work-around I have updated r8a7779_earlytimer_init() so that
shmobile_earlytimer_init() is called after r8a7779_register_twd().
Or in other words, the shmobile_earlytimer_init() setting of
late_time_init overwrites that of twd_local_timer_common_register().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
* Per-CPU SMP boot and sleep code on SoCs that use SCU
* Shared SCU CPU Hotplug code on r8a7779 and sh73a0 SoCs
* Shared SCU CPU boot code on emev2, r8a7779 and sh73a0 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=6QVN
-----END PGP SIGNATURE-----
Merge tag 'renesas-smp-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/renesas
From Simon Horman:
Renesas ARM based SoC SMP updates for v3.12
* Per-CPU SMP boot and sleep code on SoCs that use SCU
* Shared SCU CPU Hotplug code on r8a7779 and sh73a0 SoCs
* Shared SCU CPU boot code on emev2, r8a7779 and sh73a0 SoCs
* tag 'renesas-smp-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Per-CPU SMP boot / sleep code for SCU SoCs
ARM: shmobile: Introduce per-CPU SMP boot / sleep code
ARM: shmobile: Use shared SCU CPU Hotplug code on r8a7779
ARM: shmobile: Use shared SCU CPU Hotplug code on sh73a0
ARM: shmobile: Add shared SCU CPU Hotplug code
ARM: shmobile: Use shared SCU SMP boot code on emev2
ARM: shmobile: Use shared SCU SMP boot code on r8a7779
ARM: shmobile: Use shared SCU SMP boot code on sh73a0
ARM: shmobile: Introduce shared SCU SMP boot code
Signed-off-by: Olof Johansson <olof@lixom.net>
* Remove global GPIO_NR definition from sh73a0 SoC
* Remove unnecessary nfsroot settings from bootargs of
kzm9d and armadillo800eva
* Rename irq initialisation functions of r8a7779 SoC
to make them consistent with other SoCs
* Simplify irq initialisation of r8a7740 SoC
* Add missing __initdata annotations to bockw board, and
r8a7790 and r8a7779 SoCs
* Refactor time initialisation and remove shmobile_init_time.
- This affects the following boards: kzm9g, marzen, ape6evm,
armadillo800eva and bockw
- This affects the following SoCs: r8a7790, r8a7779, r7a7740, r7a73a4
* Cleanup device registration code of r8a7778 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Sbjt
-----END PGP SIGNATURE-----
Merge tag 'renesas-cleanup3-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/renesas
From Simon Horman:
Third round of Renesas ARM based SoC cleanups for v3.12
* Remove global GPIO_NR definition from sh73a0 SoC
* Remove unnecessary nfsroot settings from bootargs of
kzm9d and armadillo800eva
* Rename irq initialisation functions of r8a7779 SoC
to make them consistent with other SoCs
* Simplify irq initialisation of r8a7740 SoC
* Add missing __initdata annotations to bockw board, and
r8a7790 and r8a7779 SoCs
* Refactor time initialisation and remove shmobile_init_time.
- This affects the following boards: kzm9g, marzen, ape6evm,
armadillo800eva and bockw
- This affects the following SoCs: r8a7790, r8a7779, r7a7740, r7a73a4
* Cleanup device registration code of r8a7778 SoC
* tag 'renesas-cleanup3-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (45 commits)
ARM: shmobile: sh73a0: Remove global GPIO_NR definition
ARM: shmobile: kzm9d: remove nfsroot settings from bootargs
ARM: shmobile: armadillo800eva: remove nfsroot settings from bootargs
ARM: shmobile: r8a7779: move r8a7779_init_irq_xxx() to setup
ARM: shmobile: r8a7740: move r8a7740_init_irq_of() to setup
ARM: shmobile: bockw: add missing __initdata
ARM: shmobile: r8a7790: add missing __initdata
ARM: shmobile: r8a7779: add missing __initdata
ARM: shmobile: Remove unused shmobile_init_time()
ARM: shmobile: Use clocksource_of_init() on r8a7790
ARM: shmobile: Use default ->init_time() on KZM9G DT ref
ARM: shmobile: Use default ->init_time() on Marzen DT ref
ARM: shmobile: Use default ->init_time() on APE6EVM DT ref
ARM: shmobile: Use default ->init_time() on APE6EVM
ARM: shmobile: Use default ->init_time() on Armadillo DT ref
ARM: shmobile: Use default ->init_time() on Bockw DT ref
ARM: shmobile: Use default ->init_time() on Bockw
ARM: shmobile: Use default ->init_time() on r8a7779
ARM: shmobile: Use default ->init_time() on r8a7778
ARM: shmobile: Use default ->init_time() on r8a7740
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Remove mach/hardware.h which has no useful contents
* Remove ag5evm board support
* Remove kota2 board support
* Use pm-rmobile on sh7372 and r8a7740 SoCs only, it is otherwise unneeded
* Remove use of INTC header on r8a7779 and r8a7740 SoCs
* Cleanup registration of usb phy in r8a7779 SoC
* Remove '0x's from R8A7779 DTS file for r8a7779 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ujiw
-----END PGP SIGNATURE-----
Merge tag 'renesas-cleanup2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/renesas
From Simon Horman:
Second round of Renesas ARM based SoC cleanups for v3.12
* Remove mach/hardware.h which has no useful contents
* Remove ag5evm board support
* Remove kota2 board support
* Use pm-rmobile on sh7372 and r8a7740 SoCs only, it is otherwise unneeded
* Remove use of INTC header on r8a7779 and r8a7740 SoCs
* Cleanup registration of usb phy in r8a7779 SoC
* Remove '0x's from R8A7779 DTS file for r8a7779 SoC
* tag 'renesas-cleanup2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (74 commits)
ARM: shmobile: r8a7779: Remove '0x's from R8A7779 DTS file
ARM: shmobile: r8a7779: cleanup registration of usb phy
ARM: shmobile: No need to use INTC header on r8a7779
ARM: shmobile: No need to use INTC demux on r8a7740
ARM: shmobile: Use pm-rmobile on sh7372 and r8a7740 only
ARM: shmobile: r8a73a4: Remove ->init_machine() special case
ARM: shmobile: Remove include <mach/hardware.h>
ARM: shmobile: Remove Marzen use of <mach/hardware.h>
ARM: shmobile: Remove r8a7779 use of <mach/hardware.h>
ARM: shmobile: Remove EMEV2 use of <mach/hardware.h>
ARM: shmobile: Remove sh7372 use of <mach/hardware.h>
ARM: shmobile: Remove sh73a0 use of <mach/hardware.h>
ARCH: ARM: shmobile: Remove ag5evm board support
ARCH: ARM: shmobile: Remove kota2 board support
leds: Remove leds-renesas-tpu driver
ARM: shmobile: sh73a0: Remove all GPIOs
ARM: shmobile: kota2: Use leds-pwm + pwm-rmob
ARM: shmobile: armadillo800eva: Add backlight support
ARM: shmobile: Setup r8a7790 arch timer based on MD pins
ARM: shmobile: Introduce r8a7790_read_mode_pins()
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add ADV7180 platform devices on the Marzen board, configure VIN1/3 pins, and
register VIN1/3 devices with the ADV7180 specific platform data.
[Sergei: removed superfluous tabulation and inserted empty lines in the macro
definition, updated the copyrights, annotated VIN platform data as '__initdata']
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add VIN clocks and platform devices for R8A7779 SoC; add function to register
the VIN platform devices.
[Sergei: added 'id' parameter check to r8a7779_add_vin_device(), used '*pdata'
in *sizeof* operator there, renamed some variables, annotated vin[0-3]_resources
[] and 'vin[0-3]_info' as '__initdata'.]
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add ML86V7667 platform devices on BOCK-W board, configure VIN0/1 pins, and
register VIN0/1 devices with the ML86V7667 specific platform data.
[Sergei: some macro/comment cleanup; updated the copyrights, removed duplicate
'sh_eth' driver being enabled before registering VIN1 due to a pin conflict,
removed superfluous semicolon after iclink[01]_ml86v7667' initializer.]
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add VIN clocks and platform devices on R8A7778 SoC; add function to register
the VIN platform devices.
[Sergei: added 'id' parameter check to r8a7778_add_vin_device(), used '*pdata'
in *sizeof* operator, and added an empty line there; renamed some variables,
annotated 'vin[01]_info' and vin[01]_resources[] as '__initdata'.]
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the 'register_type' field of the 'sh_eth' driver's platform data is not
used by the driver anymore, it's time to remove it and its initializers from
the SH platform code. Also move *enum* declaring values for this field from
<linux/sh_eth.h> to the local driver's header file as they're only needed
by the driver itself now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BR17
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Minimal DRA7xx based SoC core support via Rajendra Nayak <rnayak@ti.com>
* tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (849 commits)
ARM: DRA7: Add the build support in omap2plus
ARM: DRA7: hwmod: Reuse the soc_ops used for OMAP4/5
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
ARM: DRA7: board-generic: Add basic DT support
ARM: DRA7: Resue the clocksource, clockevent support
ARM: DRA7: Reuse io tables and add a new .init_early
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
Linux 3.11-rc5
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
dlm: kill the unnecessary and wrong device_close()->recalc_sigpending()
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
From Simon Horman:
Second Round of Renesas ARM based SoC updates for v3.12
* Increased clock coverage for r8a7740 and r8a7790 SoCs
* tag 'renesas-soc2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740: Add TPU clock entry for DT platforms
ARM: shmobile: r8a7790: clocks for Ether support
ARM: shmobile: r8a7740: Fix TPU clock name
ARM: shmobile: Insert align directives before 4 bytes data
ARM: shmobile: Force ARM mode to compile reset vector for secondary CPUs
ARM: shmobile: fix compile error when CONFIG_THUMB2_KERNEL=y
ARM: shmobile: Update romImage to relocate appended DTB
Signed-off-by: Olof Johansson <olof@lixom.net>
* Fix compiler warning in armadillo800eva board code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJR+hlKAAoJENfPZGlqN0++ZqIP/ROWsUVzS35U3MhMdYps4fh0
9Vq8qwqnGVRK8UVBtf1XmETn7RSzowm0uLFDN0Rgxgo3E4ZgDAk5ux0yBrz5q9v9
sYrwuODr3SLSvoHTt3+Bt0C30+CYdA+Lxue4ToMOuP/hvPa6E680ZmwYoP/q+/bR
aU9i4ToAF9+fXUIkLEl9s/wI9Lkt4davioy/HWayLJ/2Fgn8xzWIgSQ/BADaMyRv
Ds6OmgxG1ibOcdT9RRXHSKxYkwm8obERNZHgIWPd+XDwmvF915gWTQ2XQgDhyjvn
VNq1aNYcPeqnjMN/EZZ/X+CMNwAVxmCE8ijXVkMrp8XnH7D+J/vO5rHhVuJfRtIE
NP+mi3VOCw2YQsXabCuK3bK2r2P42Pnm9gjW1iCVQAnmc7b+kAHyufVs7M6ezlKm
aFXNOcx2S3ZgnJbjzVAGayia0datDQOgEqA0zqCeZaaK05Gz/wNB/97zq4mF1ERh
YF7bAtgiJ3FHIuEEfzBexBWx20m2Xh09MwI8t6L58RHR5htuRBhbQ0ukwtgK8kSW
pq0XPQXHY9EKEdQKBLNaHFDH0GdgFUrfZdpiWNRK9O7sI08iNYEFskSTrbWKyRLW
Izafj1nPvX3v9L9hIJoxljnPkxr1lFs6pJ6NplUosmssyhrQfcGWxyn8nKWH0ram
SubsL+kwysscqIxEvgpq
=SW+C
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/fixes-non-critical
From Simon Horman:
Second Round of Renesas ARM based SoC fixes for v3.12
* Fix compiler warning in armadillo800eva board code
* tag 'renesas-fixes2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: armadillo800eva-reference: fix compiler warning
Signed-off-by: Olof Johansson <olof@lixom.net>
Move Renesas ARM based SoCs a little closer to using
multiplatform by adding ARCH_SHMOBILE_MULTI and only
building clocks when COMMON_CLK=n.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QD0i
-----END PGP SIGNATURE-----
Merge tag 'renesas-multiplatform-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM based SoC multiplatform updates for v3.12
Move Renesas ARM based SoCs a little closer to using
multiplatform by adding ARCH_SHMOBILE_MULTI and only
building clocks when COMMON_CLK=n.
* tag 'renesas-multiplatform-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Allow ARCH_SHMOBILE_MULTI timer configuration
ARM: shmobile: Add EMEV2 and KZM9D to ARCH_SHMOBILE_MULTI
ARM: shmobile: Introduce ARCH_SHMOBILE_MULTI
ARM: shmobile: Only build clocks when COMMON_CLK=n
Signed-off-by: Olof Johansson <olof@lixom.net>
Add Renesas TPU PWM unit support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=dAIB
-----END PGP SIGNATURE-----
Merge tag 'renesas-tpu-pwm-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
From Simon Horman:
Renesas TPU PWM support for v3.12
Add Renesas TPU PWM unit support
* tag 'renesas-tpu-pwm-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
leds: Remove leds-renesas-tpu driver
ARM: shmobile: sh73a0: Remove all GPIOs
ARM: shmobile: kota2: Use leds-pwm + pwm-rmob
ARM: shmobile: armadillo800eva: Add backlight support
Signed-off-by: Olof Johansson <olof@lixom.net>
SH Mobile pinctrl DT support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PwyZ
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinmux-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM based SoC pinmux updates for v3.12
SH Mobile pinctrl DT support
* tag 'renesas-pinmux-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g-reference: Add LED1-LED4 to the device tree
ARM: shmobile: kzm9g-reference: Move SDHI regulators to DT
ARM: shmobile: kzm9g-reference: Move pinctrl mappings to device tree
ARM: shmobile: marzen-reference: Add LED2-LED4 to the device tree
ARM: shmobile: marzen-reference: Move pinctrl mappings to device tree
ARM: shmobile: armadillo-reference: Add LED1-LED4 to the device tree
ARM: shmobile: armadillo-reference: Move st1232 reset GPIO to DT
ARM: shmobile: armadillo-reference: Add st1232 pin mappings
ARM: shmobile: armadillo-reference: Move pinctrl mappings to device tree
ARM: shmobile: sh73a0: Add pin control device to device tree
ARM: shmobile: sh7372: Add pin control device to device tree
ARM: shmobile: r8a7790: Add GPIO controller devices to device tree
ARM: shmobile: r8a7790: Add pin control device to device tree
ARM: shmobile: r8a7779: Add GPIO controller devices to device tree
ARM: shmobile: r8a7779: Add pin control device to device tree
ARM: shmobile: r8a7778: Add GPIO controller devices to device tree
ARM: shmobile: r8a7778: Add pin control device to device tree
ARM: shmobile: r8a7740: Add pin control device to device tree
ARM: shmobile: r8a73a4: Add pin control device to device tree
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/boot/dts/r8a73a4.dtsi
arch/arm/boot/dts/r8a7790.dtsi
- convert kirkwood, dove, orion5x to DT init of mv643xx_eth
- _lots_ of board code removal :)
- convert kirkwood, dove and orion5x to DT init of clocksource and irqchip
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJR/AlqAAoJEAi3KVZQDZAeyUMH/jWUIL53x5tIcykkT4PvM5Ki
U9B2fC77XdXSjv+gHJKt4hKYC+GNGmwAbnvBSXPwE6hqUbQhn+VodR6On5AU80xS
Dk9f3BaM3uHcemn6XXjgAWn019qSLso+AwisYC4WDJLEBMjkKE5AOvkEuP63itKz
EpV7AzfDJpQ0YM+npTqN6Ea3BNxRfZ6xv7+5fr/jM3D9tuV3Ckkun6QAyak0bSme
zEPhQOqwE/+yYb7Gu8gyslf3sX+o/xhSFdkweAxULD/LR+fNvTCAC1r2DIwP5N/n
N5/vZ6u8C5reoA3ALTsbdiEOYvBiXR94g2kSaiB0u5ptONqanXtUOwYDMVB9dD8=
=Cpj7
-----END PGP SIGNATURE-----
Merge tag 'boards-3.12' of git://git.infradead.org/linux-mvebu into next/boards
From Jason Cooper:
mvebu boards changes for v3.12
- convert kirkwood, dove, orion5x to DT init of mv643xx_eth
- _lots_ of board code removal :)
- convert kirkwood, dove and orion5x to DT init of clocksource and irqchip
* tag 'boards-3.12' of git://git.infradead.org/linux-mvebu:
ARM: plat-orion: add reg offset to DT irq driver stub
ARM: kirkwood: remove obsolete SDIO clock gate workaround
ARM: kirkwood: convert to DT irqchip and clocksource
ARM: dove: convert to DT irqchip and clocksource
ARM: orion5x: update intc device tree node to new reg layout
ARM: kirkwood: move device tree nodes to DT irqchip and clocksource
ARM: dove: move device tree nodes to DT irqchip and clocksource
ARM: orion5x: remove legacy mv643xx_eth board setup
ARM: kirkwood: remove legacy clk alias for mv643xx_eth
ARM: kirkwood: remove redundant DT board files
ARM: dove: remove legacy mv643xx_eth setup
ARM: orion5x: add gigabit ethernet and mvmdio device tree nodes
ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes
ARM: dove: add gigabit ethernet and mvmdio device tree nodes
+ Linux 3.11-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
The board has 6 LEDs connected to GPIOs. Add a led-gpio device to
support them.
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ape6evm board has switches S16 - S23 wired up to GPIO pins.
This patch allows access to those pins as gpio-keys.
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook in the per-CPU boot and sleep code in the shared
mach-shmobile SCU code. CPUs may be kept in the asm
routine until ->boot_secondary() when the per-CPU
boot vector is installed. At the end of ->die() the
asm sleep routine is invoked.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add per-CPU SMP boot / sleep code that can be used by all
SoCs included in mach-shmobile.
The boot code reads out the per-CPU MPIDR id value and
matches it with the value stored for any CPU number, and
if there is a match and the boot function is set as well
then the boot function will be executed.
The sleep code simply uses WFI and then jumps back to the
boot code to see if anyone has asked to wake up that CPU,
if not it will sleep again.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Remove trailing whitespace]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the r8a7779 specific CPU Hotplug code to make use of
the recently introduced shared SCU functions. The r8a7779
power domain hardware requires special power down handling
at ->kill() time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the sh73a0 specific CPU Hotplug code to make use of
the recently introduced shared SCU functions. The sh73a0
power control hardware relies on SCU_PM_POWEROFF with WFI
so the shared SCU code will as-is power down the hardware
as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CPU Hotplug functions for SCU equipped mach-shmobile SoCs.
The functions shmobile_smp_scu_cpu_die() together with
shmobile_smp_scu_cpu_kill() perform basic shutdown and
allows checking of shutdown status. These are written
to work together with SMP boot code in headsmp-scu.S.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SMP boot functions for SCU equipped mach-shmobile SoCs.
At this point shmobile_smp_scu_prepare_cpus() controls the SCU and
installs boot fn and arg, while shmobile_smp_scu_boot_secondary()
currently does nothing. In the future the boot function and arg
install code will be reworked, so the empty function is ground
work for that.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The total number of SoC GPIOs is only used to compute the base GPIO
number of th PCF8575 GPIO extender on the KZM9G board. As GPIO
allocation became fully dynamic with DT, no other SH73A0 board will use
the GPIO_NR macro. Move it to the KZM9G board file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch moves r8a7779_init_irq_xxx() to setup code,
and remove intc-r8a7779.
Now, r8a7779_init_irq_extpin() uses
platform_device_register_resndata() instead of
platform_device_register()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch moves r8a7740_init_irq_of() to setup code,
and remove intc-r8a7740
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds missing __initdata to driver data/resource
which are used from platform_device_register_xxx()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds missing __initdata to driver data/resource
which are used from platform_device_register_xxx()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds missing __initdata to driver data/resource
which are used from platform_device_register_xxx()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove shmobile_timer_init() since it now is unused.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the call to shmobile_timer_init() with
clocksource_of_init(). This will allow us to
get rid of shmobile_timer_init().
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: include linux/clocksource.h]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Leave ->init_time() set to NULL to use the default ARM behaviour.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sh-hspi driver which doesn't need platform data at the time of
registration can be registerd on SoC.
And, registering these drivers in the SoC code can avoid
unwanted device numbering issue.
(ex. the hspi2 device number will be spi.0 if hspi2 only registered)
This patch registers it on SoC code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
i2c-rcar driver which doesn't need platform data at the time of
registration can be registerd on SoC.
And, registering these drivers in the SoC code can avoid
unwanted device numbering issue.
(ex. the i2c3 device number will be i2c.0 if i2c3 only registered)
This patch registers it on SoC code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sdhi driver which needs platform data at the time of
registration is used from BockW only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
usb phy driver which needs platform data at the time of
registration is used from BockW only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sh_mmcif driver which needs platform data at the time of
registration is used from BockW only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Marzen is using DT booting,
and r8a7779.dtsi already has GIC settings.
So, we can remove the C version of the GIC setup code,
instead rely on GIC information provided by DT.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Armadillo800eva is using DT booting,
and r8a7740.dtsi already has GIC settings.
So, we can remove the C version of the GIC setup code,
instead rely on GIC information provided by DT.
This patch removes r8a7740_init_irq() which has
no user any more
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds missing __initdata to driver data/resource
which are used from platform_device_register_xxx()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Lager board: do not annotate gpio_buttons as __initdata
- This avoids accessing uninitialised memory if keys are pressed
after kernel initialisation completes.
- Bug introduced in gpio-keys were enabled in v3.11-rc1
* Bock-W board: fix SDHI0 PFC settings
- Allow detection of SD card
- Bug introduced in SDHI support was added in v3.11-rc1
* shdma: fixup sh_dmae_get_partial() calculation error
- Bug introduced in 2.6.34-rc1.
* armadillo800eva board: Don't request GPIO 166 in board code
- Allow use of touchscreen
- Bug introduced in v3.11-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=B1WZ
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second round of Renesas ARM based SoC fixes for v3.11
* Lager board: do not annotate gpio_buttons as __initdata
- This avoids accessing uninitialised memory if keys are pressed
after kernel initialisation completes.
- Bug introduced in gpio-keys were enabled in v3.11-rc1
* Bock-W board: fix SDHI0 PFC settings
- Allow detection of SD card
- Bug introduced in SDHI support was added in v3.11-rc1
* shdma: fixup sh_dmae_get_partial() calculation error
- Bug introduced in 2.6.34-rc1.
* armadillo800eva board: Don't request GPIO 166 in board code
- Allow use of touchscreen
- Bug introduced in v3.11-rc1
* tag 'renesas-fixes2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
shdma: fixup sh_dmae_get_partial() calculation error
ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
Signed-off-by: Olof Johansson <olof@lixom.net>
- dove
- fix section mismatch (all callers are already _init, so it's just a space
issue)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJR8WKEAAoJEAi3KVZQDZAee5EH+wfCyJExLJIEl4WvqOAL/Nme
w5WGU4NONKb4nP8OTzuN0iR1+IHU6M3kiunn44iW5DzL7Eh6xP/EtW/f43SpjXTN
slIeEfgLSsZkLt4lTlDjja/K4cB61LbZ/T/SyeY4VnoIHAUr/Z0hR4OyuDqWRIai
wMZ6X54oNz+EKXG2mXxDBysPmxywoZU8dLQfOgjYgunSk2g8D5EU03fhfLZwHRQt
cn5EEmNpjalDD4j2X04hyI5iZcH1OguaElYj5YuyYqf+8prTuNNoJ7g2eaW2Fy61
bHgx0N38rY0mhmTgVVSS6y7n0zlSlC2nl0BrjDKBAs9ekYq2NAXO9AohveOuYj0=
=kbQG
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-3.12' of git://git.infradead.org/linux-mvebu into next/fixes-non-critical
From Jason Cooper:
mvebu fixes-non-critical for v3.12
- dove
- fix section mismatch (all callers are already _init, so it's just a space
issue)
* tag 'fixes-non-3.12' of git://git.infradead.org/linux-mvebu:
ARM: dove: fix missing __init section of dove_mpp_gpio_mode
+ Linux 3.11-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds __initconst markers to the platform data and resources,
used on ape6evm as parameters to platform_device_register_resndata().
The data is duplicated inside that function, therefore original data
can be discarded after initialisation is completed.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When the gpio-keys device is registered using
platform_device_register_data() the platform data argument,
lager_keys_pdata is duplicated and thus should be marked as __initdata
to avoid wasting memory. However, this is not true of gpio_buttons,
a reference to it rather than its value is duplicated when lager_keys_pdata
is duplicated.
This avoids accessing freed memory if gpio-key events occur
after unused kernel memory is freed late in the kernel's boot.
This but was added when support for gpio-keys was added to lager
in c3842e4fcb
("ARM: shmobile: lager: support GPIO switches") which was included
in v3.11-rc1.
Tested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The following message is printed on the BOCK-W kernel bootup:
sh-pfc pfc-r8a7778: invalid group "sdhi0" for function "sdhi0"
In addition, SD card cannot be detected. The reason is apparently that commit
ca7bb30948 (ARM: shmobile: bockw: add SDHI0 support) matched
the previous version of commit 564617d2f9 (sh-pfc: r8a7778:
add SDHI support).
Add the missing pin groups according to the BOCK-W board schematics.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove r8a7779 specific ->smp_init_cpus() callback and
instead of relying on shmobile_smp_init_cpus() simply
use DT for CPU core information.
Based on work for the sh73a0 by Magnus Damm.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the marzen board to use DT_MACHINE_START. With this in
place all mach-shmobile boards use DT_MACHINE_START. Also, this
makes it possible for the r8a7779 SMP code to use DT for CPUs.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Select USE_OF in Kconfig]
[horms+renesas@verge.net.au: Provide dt_compat in DT_MACHINE_START]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
usb phy driver which needs platform data at the time of
registration is used from Marzen only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
PFC pinctrl configuration can now be performed via DT. Update
ape6evm-reference to use this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove sh73a0 specific ->smp_init_cpus() callback and
instead of relying on shmobile_smp_init_cpus() simply
use DT for CPU core information.
This assumes that DT_MACHINE_START is used which is
the case when AG5EVM and Kota2 are removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a sample DT-based Bock-W "reference" implementation.
The use of platform-specific C-code should be avoided
with this configuration as much as possible.
This patch adds new r8a7778_add_dt_devices() which was same stance
of r8a7790_add_dt_devices()
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when the intc-irqpin driver is used for external
IRQ pins on r8a7779 it possible to get rid of unused
INTC headers mach/intc.h and linux/sh_intc.h.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for SDHI0 and SDHI1 on APE6EVM in PIO mode only.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add MMCIF support to the APE6EVM board in PIO mode only. Power supply is
fixed for now, eventually support for the tps80032 regulator, also
supplying both VDD and VccQ to the MMCIF slot should be added to APE6EVM.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when the r8a7740 code has been converted to make use of
GIC instead of INTC for root interrupt controller it is
possible to exclude the low level INTC demux function
shmobile_handle_irq_intc from linking.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The functions in pm-rmobile.c are only used on sh7372 and
r8a7740, so adjust the Makefile to only link in that file
in case those SoCs are selected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
89ae7b5bbd
(ARM: shmobile: armadillo800eva: Register pinctrl mapping for INTC)
mistakenly requests GPIO 166 in board code,
most probably due to a wrong merge conflict resolution.
As the GPIO is passed to the st1232 driver through platform
data and requested by the driver,
there's no need to request it in board code. Fix it.
Tested by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No need to special case r8a73a4 ->init_machine(),
so get rid of undesired cpufreq platform device
from the generic long term r8a73a4 DT support code.
For short term support on APE6EVM the DT reference
implementation already adds a "cpufreq-cpu0" platform
device so that can be used for development.
Regarding more long term cpufreq support, perhaps
it makes sense to adjust the cpufreq driver to check
for DT information directly instead of using a
platform device for software configuration and DT
for hardware parameters.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when no one is using this file, remove <mach/hardware.h>.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove support for the sh73a0 based ag5evm board.
The sh73a0 SoC is continued to be supported using
the kzm9g board.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove support for the sh73a0 based kota2 board.
The sh73a0 SoC is continued to be supported using
the kzm9g board.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix the compiler warning:
arch/arm/mach-shmobile/board-armadillo800eva-reference.c:196:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-shmobile/board-armadillo800eva-reference.c:196:2: warning: (near initialization for '__mach_desc_ARMADILLO800EVA_DT.restart') [enabled by default]
While at it also remove superfluous parenthesis.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the timer configuration bits to allow use in
case of ARCH_SHMOBILE or ARCH_SHMOBILE_MULTI.
The timers all make use of the regular driver model
so they are safe to enable for ARCH_MULTIPLATFORM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable build of EMEV2 and KZM9D DT Reference in
case of ARCH_MULTIPLATFORM and ARCH_SHMOBILE_MULTI.
IS_ENABLED() is leaves the clock-emev2.c file out
in case of COMMON_CLK=y.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add ARCH_SHMOBILE_MULTI to mach-shmobile that can be used
to enable ARCH_MULTIPLATFORM on selected SoCs and boards.
The headers stay under arch/arm/mach-shmobile/include/mach/
for now, they can and will be migrated independently over time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move shared clock.c file and per-SoC clock-xxx.c files
to only build when CONFIG_COMMON_CLK != y.
The regular ARCH_SHMOBILE case with legacy SH clock framework
will build just as before with this patch applied, however
the case when COMMON_CLK=y will exclude all the clock files.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Create two GPIO-controlled fixed-voltage regulators in the
kzm9g-reference DT and remove manual configuration of the corresponding
GPIOs from board code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the pinctrl mappings in board code by device tree mappings.
For devices that are still instantiated from board code reference the
mappings as the default pin controller state to apply them at boot time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the pinctrl mappings in board code by device tree mappings.
For devices that are still instantiated from board code reference the
mappings as the default pin controller state to apply them at boot time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reference the st1232 reset GPIO from the device tree and remove it from
board code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the pinctrl mappings in board code by device tree mappings.
For devices that are still instantiated from board code reference the
mappings as the default pin controller state to apply them at boot time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a pfc node to the sh73a0 device tree and remove manual pinmux
initialization from the corresponding board files.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a pfc node to the r8a7779 device tree and remove manual pinmux
initialization from the corresponding board files.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a pfc node to the r8a7740 device tree and remove manual pinmux
initialization from the corresponding board files.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Guennadi Liakhovetski