ARPL and MOVSXD are encoded the same and their execution depends on the
execution mode. The operand sizes of each instruction are different.
Currently, ARPL is detected too late, after the decoding was already done, and
therefore may result in spurious exception (instead of failed emulation).
Introduce a group to the emulator to handle instructions according to execution
mode (32/64 bits). Note: in order not to make changes that may affect
performance, the new ModeDual can only be applied to instructions with ModRM.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The IRET instruction should clear NMI masking, but the current implementation
does not do so.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Indeed, Intel SDM specifically states that for the RET instruction "In 64-bit
mode, the default operation size of this instruction is the stack-address size,
i.e. 64 bits."
However, experiments show this is not the case. Here is for example objdump of
small 64-bit asm:
4004f1: ca 14 00 lret $0x14
4004f4: 48 cb lretq
4004f6: 48 ca 14 00 lretq $0x14
Therefore, remove the Stack flag from far-ret instructions.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel SDM says for CMPXCHG: "To simplify the interface to the processor’s bus,
the destination operand receives a write cycle without regard to the result of
the comparison.". This means the destination page should be dirtied.
Fix it to by writing back the original value if cmpxchg failed.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call __set_current_state() instead of assigning the new state directly.
These interfaces also aid CONFIG_DEBUG_ATOMIC_SLEEP environments,
keeping track of who changed the state.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Pull x86 fixes from Thomas Gleixner:
"Hopefully the last round of fixes for 3.19
- regression fix for the LDT changes
- regression fix for XEN interrupt handling caused by the APIC
changes
- regression fixes for the PAT changes
- last minute fixes for new the MPX support
- regression fix for 32bit UP
- fix for a long standing relocation issue on 64bit tagged for stable
- functional fix for the Hyper-V clocksource tagged for stable
- downgrade of a pr_err which tends to confuse users
Looks a bit on the large side, but almost half of it are valuable
comments"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
x86, tls, ldt: Stop checking lm in LDT_empty
x86, mpx: Strictly enforce empty prctl() args
x86, mpx: Fix potential performance issue on unmaps
x86, mpx: Explicitly disable 32-bit MPX support on 64-bit kernels
x86, hyperv: Mark the Hyper-V clocksource as being continuous
x86: Don't rely on VMWare emulating PAT MSR correctly
x86, irq: Properly tag virtualization entry in /proc/interrupts
x86, boot: Skip relocs when load address unchanged
x86/xen: Override ACPI IRQ management callback __acpi_unregister_gsi
ACPI: pci: Do not clear pci_dev->irq in acpi_pci_irq_disable()
x86/xen: Treat SCI interrupt as normal GSI interrupt
Implement a clockevent device based on the timer support available on
Hyper-V.
In this version of the patch I have addressed Jason's review comments.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 30b8b0066c "init: Get rid of x86isms" broke the UP boot on
x86_64. That happens because CONFIG_UP_LATE_INIT depends on
CONFIG_X86_UP_APIC. X86_UP_APIC is a 32bit only config switch and
therefor not set on 64bit UP builds. As a consequence the UP init of
the local APIC and the IOAPIC is not called, which results in a boot
failure.
Make it depend on !SMP && X86_LOCAL_APIC instead.
Fixes: 30b8b0066c init: Get rid of x86isms
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Resource management
- Clip bridge windows to fit in upstream windows (Yinghai Lu)
Virtualization
- Mark Atheros AR93xx to avoid using bus reset (Alex Williamson)
Miscellaneous
- Update Richard Zhu's email address (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HRy7
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for:
- a resource management problem that causes a Radeon "Fatal error
during GPU init" on machines where the BIOS programmed an invalid
Root Port window. This was a regression in v3.16.
- an Atheros AR93xx device that doesn't handle PCI bus resets
correctly. This was a regression in v3.14.
- an out-of-date email address"
* tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Richard Zhu's email address
sparc/PCI: Clip bridge windows to fit in upstream windows
powerpc/PCI: Clip bridge windows to fit in upstream windows
parisc/PCI: Clip bridge windows to fit in upstream windows
mn10300/PCI: Clip bridge windows to fit in upstream windows
microblaze/PCI: Clip bridge windows to fit in upstream windows
ia64/PCI: Clip bridge windows to fit in upstream windows
frv/PCI: Clip bridge windows to fit in upstream windows
alpha/PCI: Clip bridge windows to fit in upstream windows
x86/PCI: Clip bridge windows to fit in upstream windows
PCI: Add pci_claim_bridge_resource() to clip window if necessary
PCI: Add pci_bus_clip_resource() to clip to fit upstream window
PCI: Pass bridge device, not bus, when updating bridge windows
PCI: Mark Atheros AR93xx to avoid bus reset
PCI: Add flag for devices where we can't use bus reset
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUwkVXAAoJEL/70l94x66DwPEH/RPBmxJ+lD0nRyXVECSWxjN6
DYJvp4HsLV8BhBx/ATjAkjiVPKTUk9vQBjfgl72YatjASP9aNIkBqnN0AOVdVQ2i
04ZvYaSw3jY0A5PSecdFQZ4u8MAvaRS4AYNOYM3Kpf0EOrIwanXFpEfVRGT8ichT
uBK/mbN7vDO1SsgAnB00fCew4wFrHIa7fJ8eLNnebDOuC72oUZA+2nKx8ApWq4ca
ZaziqkI2CFaV2rqJokKDun2arxI2Q6/L87g7qyo+HMd1b+aepLTWYNOs1vH0YoSc
73aHg+3crIqx75XmnaxKP5SPOr6vpmnloux9yre8u1tvejBIbCMz1g9Mdl0YOmA=
=YRTn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Three small fixes.
Two for x86 and one avoids that sparse bails out"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
KVM: fix sparse warning in include/trace/events/kvm.h
The argument 3 of sanitize_e820_map() will only be updated upon a
successful sanitization. Some of the callers have extra conditionals
for the same purpose. Clean them up.
default_machine_specific_memory_setup() must keep the extra
conditional because boot_params.e820_entries is an u8 and not an u32,
so the direct update would overwrite other fields in boot_params.
[ tglx: Massaged changelog ]
Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Lee Chun-Yi <joeyli.kernel@gmail.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Link: http://lkml.kernel.org/r/1420601859-18439-1-git-send-email-chaowang@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
early_memremap() takes care of page alignment and map size, so we can
just remap the required data size and get rid of the adjustments in
the setup code.
[tglx: Massaged changelog ]
Signed-off-by: WANG Chao <chaowang@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Link: http://lkml.kernel.org/r/1420628150-16872-1-git-send-email-chaowang@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
1. Generic
- sparse warning (make function static)
- optimize locking
- bugfixes for interrupt injection
- fix MVPG addressing modes
2. hrtimer/wakeup fun
A recent change can cause KVM hangs if adjtime is used in the host.
The hrtimer might wake up too early or too late. Too early is fatal
as vcpu_block will see that the wakeup condition is not met and
sleep again. This CPU might never wake up again.
This series addresses this problem. adjclock slowing down the host
clock will result in too late wakeups. This will require more work.
In addition to that we also change the hrtimer from REALTIME to
MONOTONIC to avoid similar problems with timedatectl set-time.
3. sigp rework
We will move all "slow" sigps to QEMU (protected with a capability that
can be enabled) to avoid several races between concurrent SIGP orders.
4. Optimize the shadow page table
Provide an interface to announce the maximum guest size. The kernel
will use that to make the pagetable 2,3,4 (or theoretically) 5 levels.
5. Provide an interface to set the guest TOD
We now use two vm attributes instead of two oneregs, as oneregs are
vcpu ioctl and we don't want to call them from other threads.
6. Protected key functions
The real HMC allows to enable/disable protected key CPACF functions.
Lets provide an implementation + an interface for QEMU to activate
this the protected key instructions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=zLjR
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-20150122' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-next
KVM: s390: fixes and features for kvm/next (3.20)
1. Generic
- sparse warning (make function static)
- optimize locking
- bugfixes for interrupt injection
- fix MVPG addressing modes
2. hrtimer/wakeup fun
A recent change can cause KVM hangs if adjtime is used in the host.
The hrtimer might wake up too early or too late. Too early is fatal
as vcpu_block will see that the wakeup condition is not met and
sleep again. This CPU might never wake up again.
This series addresses this problem. adjclock slowing down the host
clock will result in too late wakeups. This will require more work.
In addition to that we also change the hrtimer from REALTIME to
MONOTONIC to avoid similar problems with timedatectl set-time.
3. sigp rework
We will move all "slow" sigps to QEMU (protected with a capability that
can be enabled) to avoid several races between concurrent SIGP orders.
4. Optimize the shadow page table
Provide an interface to announce the maximum guest size. The kernel
will use that to make the pagetable 2,3,4 (or theoretically) 5 levels.
5. Provide an interface to set the guest TOD
We now use two vm attributes instead of two oneregs, as oneregs are
vcpu ioctl and we don't want to call them from other threads.
6. Protected key functions
The real HMC allows to enable/disable protected key CPACF functions.
Lets provide an implementation + an interface for QEMU to activate
this the protected key instructions.
SYSENTER emulation is broken in several ways:
1. It misses the case of 16-bit code segments completely (CVE-2015-0239).
2. MSR_IA32_SYSENTER_CS is checked in 64-bit mode incorrectly (bits 0 and 1 can
still be set without causing #GP).
3. MSR_IA32_SYSENTER_EIP and MSR_IA32_SYSENTER_ESP are not masked in
legacy-mode.
4. There is some unneeded code.
Fix it.
Cc: stable@vger.linux.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
STR and SLDT with rip-relative operand can cause a host kernel oops.
Mark them as DstMem as well.
Cc: stable@vger.linux.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The return value of kvm_arch_vcpu_postcreate is not checked in its
caller. This is okay, because only x86 provides vcpu_postcreate right
now and it could only fail if vcpu_load failed. But that is not
possible during KVM_CREATE_VCPU (kvm_arch_vcpu_load is void, too), so
just get rid of the unchecked return value.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Many users see this message when booting without knowning that it is
of no importance and that TSC calibration may have succeeded by
another way.
As explained by Paul Bolle in
http://lkml.kernel.org/r/1348488259.1436.22.camel@x61.thuisdomein
"Fast TSC calibration failed" should not be considered as an error
since other calibration methods are being tried afterward. At most,
those send a warning if they fail (not an error). So let's change
the message from error to warning.
[ tglx: Make if pr_info. It's really not important at all ]
Fixes: c767a54ba0 x86/debug: Add KERN_<LEVEL> to bare printks, convert printks to pr_<level>
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1418106470-6906-1-git-send-email-alexandre.f.demers@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Building with clang:
CC arch/x86/kernel/rtc.o
arch/x86/kernel/rtc.c:173:29: warning: duplicate 'const' declaration
specifier [-Wduplicate-decl-specifier]
static const char * const const ids[] __initconst =
Remove the duplicate const, it is not needed and causes a warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: http://lkml.kernel.org/r/1421244475-313-1-git-send-email-colin.king@canonical.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 0dbc6078c0 ('x86, build, pci: Fix PCI_MSI build on !SMP')
introduced the dependency that X86_UP_APIC is only available when
PCI_MSI is false. This effectively prevents PCI_MSI support on 32bit
UP systems because it disables both APIC and IO-APIC. But APIC support
is architecturally required for PCI_MSI.
The intention of the patch was to enforce APIC support when PCI_MSI is
enabled, but failed to do so.
Remove the !PCI_MSI dependency from X86_UP_APIC and enforce
X86_UP_APIC when PCI_MSI support is enabled on 32bit UP systems.
[ tglx: Massaged changelog ]
Fixes 0dbc6078c0 'x86, build, pci: Fix PCI_MSI build on !SMP'
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1421967529-9037-1-git-send-email-pure.logic@nexus-software.ie
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 281d4078be ("x86: Make page cache mode a real type")
introduced the symbols __cachemode2pte_tbl and __pte2cachemode_tbl and
exported them via EXPORT_SYMBOL_GPL. The exports are part of a
replacement of code which has been EXPORT_SYMBOL before these changes
resulting in build breakage of out-of-tree non-gpl modules.
Change EXPORT_SYMBOL_GPL to EXPORT-SYMBOL for these two symbols.
Fixes: 281d4078be "x86: Make page cache mode a real type"
Reported-and-tested-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Link: http://lkml.kernel.org/r/1421926997-28615-1-git-send-email-jgross@suse.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Witcher 2 did something like this to allocate a TLS segment index:
struct user_desc u_info;
bzero(&u_info, sizeof(u_info));
u_info.entry_number = (uint32_t)-1;
syscall(SYS_set_thread_area, &u_info);
Strictly speaking, this code was never correct. It should have set
read_exec_only and seg_not_present to 1 to indicate that it wanted
to find a free slot without putting anything there, or it should
have put something sensible in the TLS slot if it wanted to allocate
a TLS entry for real. The actual effect of this code was to
allocate a bogus segment that could be used to exploit espfix.
The set_thread_area hardening patches changed the behavior, causing
set_thread_area to return -EINVAL and crashing the game.
This changes set_thread_area to interpret this as a request to find
a free slot and to leave it empty, which isn't *quite* what the game
expects but should be close enough to keep it working. In
particular, using the code above to allocate two segments will
allocate the same segment both times.
According to FrostbittenKing on Github, this fixes The Witcher 2.
If this somehow still causes problems, we could instead allocate
a limit==0 32-bit data segment, but that seems rather ugly to me.
Fixes: 41bdc78544 x86/tls: Validate TLS entries to protect espfix
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: stable@vger.kernel.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/0cb251abe1ff0958b8e468a9a9a905b80ae3a746.1421954363.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The 3.19 merge window saw some TLB modifications merged which caused a
performance regression. They were fixed in commit 045bbb9fa.
Once that fix was applied, I also noticed that there was a small
but intermittent regression still present. It was not present
consistently enough to bisect reliably, but I'm fairly confident
that it came from (my own) MPX patches. The source was reading
a relatively unused field in the mm_struct via arch_unmap.
I also noted that this code was in the main instruction flow of
do_munmap() and probably had more icache impact than we want.
This patch does two things:
1. Adds a static (via Kconfig) and dynamic (via cpuid) check
for MPX with cpu_feature_enabled(). This keeps us from
reading that cacheline in the mm and trades it for a check
of the global CPUID variables at least on CPUs without MPX.
2. Adds an unlikely() to ensure that the MPX call ends up out
of the main instruction flow in do_munmap(). I've added
a detailed comment about why this was done and why we want
it even on systems where MPX is present.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: luto@amacapital.net
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20150108223021.AEEAB987@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We had originally planned on submitting MPX support in one patch
set. We eventually broke it up in to two pieces for easier
review. One of the features that didn't make the first round
was supporting 32-bit binaries on 64-bit kernels.
Once we split the set up, we never added code to restrict 32-bit
binaries from _using_ MPX on 64-bit kernels.
The 32-bit bounds tables are a different format than the 64-bit
ones. Without this patch, the kernel will try to read a 32-bit
binary's tables as if they were the 64-bit version. They will
likely be noticed as being invalid rather quickly and the app
will get killed, but that's kinda mean.
This patch adds an explicit check, and will make a 64-bit kernel
essentially behave as if it has no MPX support when called from
a 32-bit binary.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20150108223020.9E9AA511@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
First two are minor fallout from the param rework which went in this merge
window.
Next three are a series which fixes a longstanding (but never previously
reported and unlikely , so no CC stable) race between kallsyms and freeing
the init section.
Finally, a minor cleanup as our module refcount will now be -1 during
unload.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Kf9b
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module and param fixes from Rusty Russell:
"Surprising number of fixes this merge window :(
The first two are minor fallout from the param rework which went in
this merge window.
The next three are a series which fixes a longstanding (but never
previously reported and unlikely , so no CC stable) race between
kallsyms and freeing the init section.
Finally, a minor cleanup as our module refcount will now be -1 during
unload"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: make module_refcount() a signed integer.
module: fix race in kallsyms resolution during module load success.
module: remove mod arg from module_free, rename module_memfree().
module_arch_freeing_init(): new hook for archs before module->module_init freed.
param: fix uninitialized read with CONFIG_DEBUG_LOCK_ALLOC
param: initialize store function to NULL if not available.
Now that the APIC bringup is consolidated we can move the setup call
for the percpu clock event device to apic_bsp_setup().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211704.162567839@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Extend apic_bsp_setup() so the same code flow can be used for
APIC_init_uniprocessor().
Folded Jiangs fix to provide proper ordering of the UP setup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211704.084765674@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The UP related setups for local apic are mangled into smp_sanity_check().
That results in duplicate calls to disable_smp() and makes the code
hard to follow. Let smp_sanity_check() return dedicated values for the
various exit reasons and handle them at the call site.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.987833932@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We better provide proper functions which implement the required code
flow in the apic code rather than letting the smpboot code open code
it. That allows to make more functions static and confines the APIC
functionality to apic.c where it belongs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.907616730@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The UP local API support can be set up from an early initcall. No need
for horrible hackery in the init code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211703.827943883@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the code to a different place so we can make other functions
inline. Preparatory patch for further cleanups. No change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.731329006@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
smpboot is very creative with the ways to disable ioapic.
smpboot_clear_io_apic() smpboot_clear_io_apic_irqs() and
disable_ioapic_support() serve a similar purpose.
smpboot_clear_io_apic_irqs() is the most useless of all
functions as it clears a variable which has not been setup yet.
Aside of that it has the same ifdef mess and conditionals around the
ioapic related code, which can now be removed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.650280684@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have proper stubs for the IOAPIC=n case and the setup/enable
function have the required checks inside now. Remove the ifdeffery and
the copy&pasted conditionals.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>C
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.569830549@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No point to have the same checks at every call site. Add them to the
functions, so they can be called unconditionally.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.490719938@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To avoid lots of ifdeffery provide proper stubs for setup_IO_APIC(),
enable_IO_APIC() and setup_ioapic_dest().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.397170414@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No point for a separate header file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211703.304126687@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the state information to simplify the disable logic further.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211703.209387598@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
enable_x2apic() is a convoluted unreadable mess because it is used for
both enablement in early boot and for setup in cpu_init().
Split the code into x2apic_enable() for enablement and x2apic_setup()
for setup of (secondary cpus). Make use of the new state tracking to
simplify the logic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211703.129287153@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no point in postponing the hardware disablement of x2apic. It
can be disabled right away in the nox2apic setup function.
Disable it right away and set the state to DISABLED . This allows to
remove all the nox2apic conditionals all over the place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211703.051214090@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Having 3 different variables to track the state is just silly and
error prone. Add a proper state tracking variable which covers the
three possible states: ON/OFF/DISABLED.
We cannot use x2apic_mode for this as this would require to change all
users of x2apic_mode with explicit comparisons for a state value
instead of treating it as boolean.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211702.955392443@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename the argument of try_to_enable_x2apic() so the purpose becomes
more clear.
Make the pr_warning more consistent and avoid the double print of
"disabling".
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211702.876012628@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No point in having try_to_enable_x2apic() outside of the
CONFIG_X86_X2APIC section and having inline functions and more ifdefs
to deal with it. Move the code into the existing ifdef section and
remove the inline cruft.
Fixup the printk about not enabling interrupt remapping as suggested
by Boris.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211702.795388613@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No point in delaying the x2apic detection for the CONFIG_X86_X2APIC=n
case to enable_IR_x2apic(). We rather detect that before we try to
setup anything there.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211702.702479404@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If x2apic_preenabled is not enabled, then disable_x2apic() is not
called from various places which results in x2apic_disabled not being
set. So other code pathes can happily reenable the x2apic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211702.621431109@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The x2apic_preenabled flag is just a horrible hack and if X2APIC
support is disabled it does not reflect the actual hardware
state. Check the hardware instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20150115211702.541280622@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Having several disjunct pieces of code for x2apic support makes
reading the code unnecessarily hard. Move it to one ifdeffed section.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211702.445212133@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No point in having a static variable around which is always 0. Let the
compiler optimize code out if disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211702.363274310@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
enable_IR_x2apic() grew a open coded x2apic detection. Implement a
proper helper function which shares the code with the already existing
x2apic_enabled().
Made it use rdmsrl_safe as suggested by Boris.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20150115211702.285038186@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kvm/emulate.c: In function ‘check_cr_write’:
arch/x86/kvm/emulate.c:3552:4: warning: left shift count >= width of type
rsvd = CR3_L_MODE_RESERVED_BITS & ~CR3_PCID_INVD;
happens because sizeof(UL) on 32-bit is 4 bytes but we shift it 63 bits
to the left.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull RCU updates from Paul E. McKenney:
- Documentation updates.
- Miscellaneous fixes.
- Preemptible-RCU fixes, including fixing an old bug in the
interaction of RCU priority boosting and CPU hotplug.
- SRCU updates.
- RCU CPU stall-warning updates.
- RCU torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
SuSE's 2.6.16 kernel fails to boot if the delta between tsc_timestamp
and rdtsc is larger than a given threshold:
* If we get more than the below threshold into the future, we rerequest
* the real time from the host again which has only little offset then
* that we need to adjust using the TSC.
*
* For now that threshold is 1/5th of a jiffie. That should be good
* enough accuracy for completely broken systems, but also give us swing
* to not call out to the host all the time.
*/
#define PVCLOCK_DELTA_MAX ((1000000000ULL / HZ) / 5)
Disable masterclock support (which increases said delta) in case the
boot vcpu does not use MSR_KVM_SYSTEM_TIME_NEW.
Upstreams kernels which support pvclock vsyscalls (and therefore make
use of PVCLOCK_STABLE_BIT) use MSR_KVM_SYSTEM_TIME_NEW.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
arch/x86/kvm/x86.c:495:5: sparse: symbol 'kvm_read_nested_guest_page' was not declared. Should it be static?
arch/x86/kvm/x86.c:646:5: sparse: symbol '__kvm_set_xcr' was not declared. Should it be static?
arch/x86/kvm/x86.c:1183:15: sparse: symbol 'max_tsc_khz' was not declared. Should it be static?
arch/x86/kvm/x86.c:1237:6: sparse: symbol 'kvm_track_tsc_matching' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In Dom0's the use of the TSC clocksource (whenever it is stable enough to
be used) instead of the Xen clocksource should not cause any issues, as
Dom0 VMs never live-migrated. The TSC clocksource is somewhat more
efficient than the Xen paravirtualised clocksource, thus it should have
higher rating.
This patch decreases the rating of the Xen clocksource in Dom0s to 275.
Which is half-way between the rating of the TSC clocksource (300) and the
hpet clocksource (250).
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: Imre Palik <imrep@amazon.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Change ARCH_HAVE_LIVE_PATCHING to HAVE_LIVE_PATCHING in Kconfigs. HAVE_
bools are prevalent there and we should go with the flow.
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
VMWare seems not to emulate the PAT MSR correctly: reaeding
MSR_IA32_CR_PAT returns 0 even after writing another value to it.
Commit bd809af16e triggers this VMWare bug when the kernel is
booted as a VMWare guest.
Detect this bug and don't use the read value if it is 0.
Fixes: bd809af16e "x86: Enable PAT to use cache mode translation tables"
Reported-and-tested-by: Jongman Heo <jongman.heo@samsung.com>
Acked-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: http://lkml.kernel.org/r/1421039745-14335-1-git-send-email-jgross@suse.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
math_state_restore() can race with kernel_fpu_begin() if irq comes
right after __thread_fpu_begin(), __save_init_fpu() will overwrite
fpu->state we are going to restore.
Add 2 simple helpers, kernel_fpu_disable() and kernel_fpu_enable()
which simply set/clear in_kernel_fpu, and change math_state_restore()
to exclude kernel_fpu_begin() in between.
Alternatively we could use local_irq_save/restore, but probably these
new helpers can have more users.
Perhaps they should disable/enable preemption themselves, in this case
we can remove preempt_disable() in __restore_xstate_sig().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: matt.fleming@intel.com
Cc: bp@suse.de
Cc: pbonzini@redhat.com
Cc: luto@amacapital.net
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Link: http://lkml.kernel.org/r/20150115192028.GD27332@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that we have in_kernel_fpu we can remove __thread_clear_has_fpu()
in __kernel_fpu_begin(). And this allows to replace the asymmetrical
and nontrivial use_eager_fpu + tsk_used_math check in kernel_fpu_end()
with the same __thread_has_fpu() check.
The logic becomes really simple; if _begin() does save() then _end()
needs restore(), this is controlled by __thread_has_fpu(). Otherwise
they do clts/stts unless use_eager_fpu().
Not only this makes begin/end symmetrical and imo more understandable,
potentially this allows to change irq_fpu_usable() to avoid all other
checks except "in_kernel_fpu".
Also, with this patch __kernel_fpu_end() does restore_fpu_checking()
and WARNs if it fails instead of math_state_restore(). I think this
looks better because we no longer need __thread_fpu_begin(), and it
would be better to report the failure in this case.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: matt.fleming@intel.com
Cc: bp@suse.de
Cc: pbonzini@redhat.com
Cc: luto@amacapital.net
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Link: http://lkml.kernel.org/r/20150115192005.GC27332@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
interrupted_kernel_fpu_idle() tries to detect if kernel_fpu_begin()
is safe or not. In particular it should obviously deny the nested
kernel_fpu_begin() and this logic looks very confusing.
If use_eager_fpu() == T we rely on a) __thread_has_fpu() check in
interrupted_kernel_fpu_idle(), and b) on the fact that _begin() does
__thread_clear_has_fpu().
Otherwise we demand that the interrupted task has no FPU if it is in
kernel mode, this works because __kernel_fpu_begin() does clts() and
interrupted_kernel_fpu_idle() checks X86_CR0_TS.
Add the per-cpu "bool in_kernel_fpu" variable, and change this code
to check/set/clear it. This allows to do more cleanups and fixes, see
the next changes.
The patch also moves WARN_ON_ONCE() under preempt_disable() just to
make this_cpu_read() look better, this is not really needed. And in
fact I think we should move it into __kernel_fpu_begin().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: matt.fleming@intel.com
Cc: bp@suse.de
Cc: pbonzini@redhat.com
Cc: luto@amacapital.net
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Link: http://lkml.kernel.org/r/20150115191943.GB27332@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The PSS register reflects the power state of each island on SoC. It would be
useful to know which of the islands is on or off at the momemnt.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Kumar P. Mahesh <mahesh.kumar.p@intel.com>
Link: http://lkml.kernel.org/r/1421253575-22509-6-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no need to use err variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Kumar P. Mahesh <mahesh.kumar.p@intel.com>
Link: http://lkml.kernel.org/r/1421253575-22509-5-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
DRIVER_NAME seems unused. This patch just removes it. There is no functional
change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Kumar P. Mahesh <mahesh.kumar.p@intel.com>
Link: http://lkml.kernel.org/r/1421253575-22509-4-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
debugfs_remove_recursive() is NULL-aware, thus, we may safely remove the check
here. There is no need to assing NULL to variable since it will be not used
anywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Kumar P. Mahesh <mahesh.kumar.p@intel.com>
Link: http://lkml.kernel.org/r/1421253575-22509-3-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
pmc_dbgfs_unregister() will be called when pmc->dbgfs_dir is unconditionally
NULL on error path in pmc_dbgfs_register(). To prevent this we move the
assignment to where is should be.
Fixes: f855911c1f (x86/pmc_atom: Expose PMC device state and platform sleep state)
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Kumar P. Mahesh <mahesh.kumar.p@intel.com>
Link: http://lkml.kernel.org/r/1421253575-22509-2-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On 64-bit, relocation is not required unless the load address gets
changed. Without this, relocations do unexpected things when the kernel
is above 4G.
Reported-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Thomas D. <whissi@whissi.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Junjie Mao <eternal.n08@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20150116005146.GA4212@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xen overrides __acpi_register_gsi and leaves __acpi_unregister_gsi as is.
That means, an IRQ allocated by acpi_register_gsi_xen_hvm() or
acpi_register_gsi_xen() will be freed by acpi_unregister_gsi_ioapic(),
which may cause undesired effects. So override __acpi_unregister_gsi to
NULL for safety.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Graeme Gregory <graeme.gregory@linaro.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Link: http://lkml.kernel.org/r/1421720467-7709-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently Xen Domain0 has special treatment for ACPI SCI interrupt,
that is initialize irq for ACPI SCI at early stage in a special way as:
xen_init_IRQ()
->pci_xen_initial_domain()
->xen_setup_acpi_sci()
Allocate and initialize irq for ACPI SCI
Function xen_setup_acpi_sci() calls acpi_gsi_to_irq() to get an irq
number for ACPI SCI. But unfortunately acpi_gsi_to_irq() depends on
IOAPIC irqdomains through following path
acpi_gsi_to_irq()
->mp_map_gsi_to_irq()
->mp_map_pin_to_irq()
->check IOAPIC irqdomain
For PV domains, it uses Xen event based interrupt manangement and
doesn't make uses of native IOAPIC, so no irqdomains created for IOAPIC.
This causes Xen domain0 fail to install interrupt handler for ACPI SCI
and all ACPI events will be lost. Please refer to:
https://lkml.org/lkml/2014/12/19/178
So the fix is to get rid of special treatment for ACPI SCI, just treat
ACPI SCI as normal GSI interrupt as:
acpi_gsi_to_irq()
->acpi_register_gsi()
->acpi_register_gsi_xen()
->xen_register_gsi()
With above change, there's no need for xen_setup_acpi_sci() anymore.
The above change also works with bare metal kernel too.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1421720467-7709-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull crypto fix from Herbert Xu:
"This fixes a regression that arose from the change to add a crypto
prefix to module names which was done to prevent the loading of
arbitrary modules through the Crypto API.
In particular, a number of modules were missing the crypto prefix
which meant that they could no longer be autoloaded"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: add missing crypto module aliases
Nothing needs the module pointer any more, and the next patch will
call it from RCU, where the module itself might no longer exist.
Removing the arg is the safest approach.
This just codifies the use of the module_alloc/module_free pattern
which ftrace and bpf use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: x86@kernel.org
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: linux-cris-kernel@axis.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: nios2-dev@lists.rocketboards.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: netdev@vger.kernel.org
commit 78bff1c868 ("x86/ticketlock: Fix spin_unlock_wait() livelock")
introduced two additional ACCESS_ONCE cases in x86 spinlock.h.
Lets change those as well.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
ACCESS_ONCE does not work reliably on non-scalar types. For
example gcc 4.6 and 4.7 might remove the volatile tag for such
accesses during the SRA (scalar replacement of aggregates) step
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145)
Change the p2m code to replace ACCESS_ONCE with READ_ONCE.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
No TLB flush is needed when there's no valid rmap in memory slot.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Removes some functions that are not used anywhere:
cpu_has_vmx_eptp_writeback() cpu_has_vmx_eptp_uncacheable()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also two PMU driver fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools powerpc: Use dwfl_report_elf() instead of offline.
perf tools: Fix segfault for symbol annotation on TUI
perf test: Fix dwarf unwind using libunwind.
perf tools: Avoid build splat for syscall numbers with uclibc
perf tools: Elide strlcpy warning with uclibc
perf tools: Fix statfs.f_type data type mismatch build error with uclibc
tools: Remove bitops/hweight usage of bits in tools/perf
perf machine: Fix __machine__findnew_thread() error path
perf tools: Fix building error in x86_64 when dwarf unwind is on
perf probe: Propagate error code when write(2) failed
perf/x86/intel: Fix bug for "cycles:p" and "cycles:pp" on SLM
perf/rapl: Fix sysfs_show() initialization for RAPL PMU
The int_ret_from_sys_call and syscall tracing code disagrees
with the sysret path as to the value of RCX.
The Intel SDM, the AMD APM, and my laptop all agree that sysret
returns with RCX == RIP. The syscall tracing code does not
respect this property.
For example, this program:
int main()
{
extern const char syscall_rip[];
unsigned long rcx = 1;
unsigned long orig_rcx = rcx;
asm ("mov $-1, %%eax\n\t"
"syscall\n\t"
"syscall_rip:"
: "+c" (rcx) : : "r11");
printf("syscall: RCX = %lX RIP = %lX orig RCX = %lx\n",
rcx, (unsigned long)syscall_rip, orig_rcx);
return 0;
}
prints:
syscall: RCX = 400556 RIP = 400556 orig RCX = 1
Running it under strace gives this instead:
syscall: RCX = FFFFFFFFFFFFFFFF RIP = 400556 orig RCX = 1
This changes FIXUP_TOP_OF_STACK to match sysret, causing the
test to show RCX == RIP even under strace.
It looks like this is a partial revert of:
88e4bc32686e ("[PATCH] x86-64 architecture specific sync for 2.5.8")
from the historic git tree.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/c9a418c3dc3993cb88bb7773800225fd318a4c67.1421453410.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
the mixture of function graph tracing and kprobes.
When jprobes and function graph tracing is enabled at the same time
it will crash the system.
# modprobe jprobe_example
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
After the first fork (jprobe_example probes it), the system will crash.
This is due to the way jprobes copies the stack frame and does not
do a normal function return. This messes up with the function graph
tracing accounting which hijacks the return address from the stack
and replaces it with a hook function. It saves the return addresses in
a separate stack to put back the correct return address when done.
But because the jprobe functions do not do a normal return, their
stack addresses are not put back until the function they probe is called,
which means that the probed function will get the return address of
the jprobe handler instead of its own.
The simple fix here was to disable function graph tracing while the
jprobe handler is being called.
While debugging this I found two minor bugs with the function graph
tracing.
The first was about the function graph tracer sharing its function hash
with the function tracer (they both get filtered by the same input).
The changing of the set_ftrace_filter would not sync the function recording
records after a change if the function tracer was disabled but the
function graph tracer was enabled. This was due to the update only checking
one of the ops instead of the shared ops to see if they were enabled and
should perform the sync. This caused the ftrace accounting to break and
a ftrace_bug() would be triggered, disabling ftrace until a reboot.
The second was that the check to update records only checked one of the
filter hashes. It needs to test both the "filter" and "notrace" hashes.
The "filter" hash determines what functions to trace where as the "notrace"
hash determines what functions not to trace (trace all but these).
Both hashes need to be passed to the update code to find out what change
is being done during the update. This also broke the ftrace record
accounting and triggered a ftrace_bug().
This patch set also include two more fixes that were reported separately
from the kprobe issue.
One was that init_ftrace_syscalls() was called twice at boot up.
This is not a major bug, but that call performed a rather large kmalloc
(NR_syscalls * sizeof(*syscalls_metadata)). The second call made the first
one a memory leak, and wastes memory.
The other fix is a regression caused by an update in the v3.19 merge window.
The moving to enable events early, moved the enabling before PID 1 was
created. The syscall events require setting the TIF_SYSCALL_TRACEPOINT
for all tasks. But for_each_process_thread() does not include the swapper
task (PID 0), and ended up being a nop. A suggested fix was to add
the init_task() to have its flag set, but I didn't really want to mess
with PID 0 for this minor bug. Instead I disable and re-enable events again
at early_initcall() where it use to be enabled. This also handles any other
event that might have its own reg function that could break at early
boot up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUt9vmAAoJEEjnJuOKh9ldLHEIAJ9XrPW2xMIY5yI69jT1F7pv
PkSRqENnOK0l4UulD52SvIBecQTTBcEEjao4yVGkc7DCJBOws/1LZ5gW8OfNlKjq
rMB8yaosL1tXJ1ARVPMjcQVy+228zkgTXznwEZCjku1g7LuScQ28qyXsXO7B6yiK
xKoHqKjygmM/a2aVn+8tdiVKiDp6jdmkbYicbaFT4xP7XB5DaMmIiXRHxdvW6xdR
azKrVfYiMyJqTZNt/EVSWUk2WjeaYhoXyNtvgPx515wTo/llCnzhjcsocXBtH2P/
YOtwl+1L7Z89ukV9oXqrtrUJZ6Ps7+g7I1flJuL7/1FlNGnklcP9JojD+t6HeT8=
=vkec
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fixes from Steven Rostedt:
"This holds a few fixes to the ftrace infrastructure as well as the
mixture of function graph tracing and kprobes.
When jprobes and function graph tracing is enabled at the same time it
will crash the system:
# modprobe jprobe_example
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
After the first fork (jprobe_example probes it), the system will
crash.
This is due to the way jprobes copies the stack frame and does not do
a normal function return. This messes up with the function graph
tracing accounting which hijacks the return address from the stack and
replaces it with a hook function. It saves the return addresses in a
separate stack to put back the correct return address when done. But
because the jprobe functions do not do a normal return, their stack
addresses are not put back until the function they probe is called,
which means that the probed function will get the return address of
the jprobe handler instead of its own.
The simple fix here was to disable function graph tracing while the
jprobe handler is being called.
While debugging this I found two minor bugs with the function graph
tracing.
The first was about the function graph tracer sharing its function
hash with the function tracer (they both get filtered by the same
input). The changing of the set_ftrace_filter would not sync the
function recording records after a change if the function tracer was
disabled but the function graph tracer was enabled. This was due to
the update only checking one of the ops instead of the shared ops to
see if they were enabled and should perform the sync. This caused the
ftrace accounting to break and a ftrace_bug() would be triggered,
disabling ftrace until a reboot.
The second was that the check to update records only checked one of
the filter hashes. It needs to test both the "filter" and "notrace"
hashes. The "filter" hash determines what functions to trace where as
the "notrace" hash determines what functions not to trace (trace all
but these). Both hashes need to be passed to the update code to find
out what change is being done during the update. This also broke the
ftrace record accounting and triggered a ftrace_bug().
This patch set also include two more fixes that were reported
separately from the kprobe issue.
One was that init_ftrace_syscalls() was called twice at boot up. This
is not a major bug, but that call performed a rather large kmalloc
(NR_syscalls * sizeof(*syscalls_metadata)). The second call made the
first one a memory leak, and wastes memory.
The other fix is a regression caused by an update in the v3.19 merge
window. The moving to enable events early, moved the enabling before
PID 1 was created. The syscall events require setting the
TIF_SYSCALL_TRACEPOINT for all tasks. But for_each_process_thread()
does not include the swapper task (PID 0), and ended up being a nop.
A suggested fix was to add the init_task() to have its flag set, but I
didn't really want to mess with PID 0 for this minor bug. Instead I
disable and re-enable events again at early_initcall() where it use to
be enabled. This also handles any other event that might have its own
reg function that could break at early boot up"
* tag 'trace-fixes-v3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix enabling of syscall events on the command line
tracing: Remove extra call to init_ftrace_syscalls()
ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing
ftrace: Check both notrace and filter for old hash
ftrace: Fix updating of filters for shared global_ops filters
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Tested-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: x86@kernel.org
CC: stable@vger.kernel.org # v3.16+
We now have a generic function that does most of the work of
kvm_vm_ioctl_get_dirty_log, now use it.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
cycles:p and cycles:pp do not work on SLM since commit:
86a04461a9 ("perf/x86: Revamp PEBS event selection")
UOPS_RETIRED.ALL is not a PEBS capable event, so it should not be used
to count cycle number.
Actually SLM calls intel_pebs_aliases_core2() which uses INST_RETIRED.ANY_P
to count the number of cycles. It's a PEBS capable event. But inv and
cmask must be set to count cycles.
Considering SLM allows all events as PEBS with no flags, only
INST_RETIRED.ANY_P, inv=1, cmask=16 needs to handled specially.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1421084541-31639-1-git-send-email-kan.liang@intel.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fixes a problem with the initialization of the
sysfs_show() routine for the RAPL PMU.
The current code was wrongly relying on the EVENT_ATTR_STR()
macro which uses the events_sysfs_show() function in the x86
PMU code. That function itself was relying on the x86_pmu data
structure. Yet RAPL and the core PMU (x86_pmu) have nothing to
do with each other. They should therefore not interact with
each other.
The x86_pmu structure is initialized at boot time based on
the host CPU model. When the host CPU is not supported, the
x86_pmu remains uninitialized and some of the callbacks it
contains are NULL.
The false dependency with x86_pmu could potentially cause crashes
in case the x86_pmu is not initialized while the RAPL PMU is. This
may, for instance, be the case in virtualized environments.
This patch fixes the problem by using a private sysfs_show()
routine for exporting the RAPL PMU events.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150113225953.GA21525@thinkpad
Cc: vincent.weaver@maine.edu
Cc: jolsa@redhat.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the function graph tracer traces a jprobe callback, the system will
crash. This can easily be demonstrated by compiling the jprobe
sample module that is in the kernel tree, loading it and running the
function graph tracer.
# modprobe jprobe_example.ko
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
# ls
The first two commands end up in a nice crash after the first fork.
(do_fork has a jprobe attached to it, so "ls" just triggers that fork)
The problem is caused by the jprobe_return() that all jprobe callbacks
must end with. The way jprobes works is that the function a jprobe
is attached to has a breakpoint placed at the start of it (or it uses
ftrace if fentry is supported). The breakpoint handler (or ftrace callback)
will copy the stack frame and change the ip address to return to the
jprobe handler instead of the function. The jprobe handler must end
with jprobe_return() which swaps the stack and does an int3 (breakpoint).
This breakpoint handler will then put back the saved stack frame,
simulate the instruction at the beginning of the function it added
a breakpoint to, and then continue on.
For function tracing to work, it hijakes the return address from the
stack frame, and replaces it with a hook function that will trace
the end of the call. This hook function will restore the return
address of the function call.
If the function tracer traces the jprobe handler, the hook function
for that handler will not be called, and its saved return address
will be used for the next function. This will result in a kernel crash.
To solve this, pause function tracing before the jprobe handler is called
and unpause it before it returns back to the function it probed.
Some other updates:
Used a variable "saved_sp" to hold kcb->jprobe_saved_sp. This makes the
code look a bit cleaner and easier to understand (various tries to fix
this bug required this change).
Note, if fentry is being used, jprobes will change the ip address before
the function graph tracer runs and it will not be able to trace the
function that the jprobe is probing.
Link: http://lkml.kernel.org/r/20150114154329.552437962@goodmis.org
Cc: stable@vger.kernel.org # 2.6.30+
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
access the mmcfg space - some error injection functions need to do
this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3MwK
-----END PGP SIGNATURE-----
Merge tag 'please-pull-einj-mmcfg' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull RAS update from Tony Luck:
"When checking addresses in APEI action entries for validity, allow
access to the mmcfg space - some error injection functions need to do
this."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
and a cleanup from me.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r9gb
-----END PGP SIGNATURE-----
Merge tag 'ras_for_3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/ras
Pull RAS updates from Borislav Petkov:
"Nothing special this time, just an error messages improvement from Andy
and a cleanup from me."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Simplify irq_remapping code by killing irq_remapping_supported() and
related interfaces.
Joerg posted a similar patch at https://lkml.org/lkml/2014/12/15/490,
so assume an signed-off from Joerg.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When interrupt remapping hardware is not in X2APIC, CPU X2APIC mode
will be disabled if:
1) Maximum CPU APIC ID is bigger than 255
2) hypervisior doesn't support x2apic mode.
But we should only check whether hypervisor supports X2APIC mode when
hypervisor(CONFIG_HYPERVISOR_GUEST) is enabled, otherwise X2APIC will
always be disabled when CONFIG_HYPERVISOR_GUEST is disabled and IR
doesn't work in X2APIC mode.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-12-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If remapping is in XAPIC mode, the setup code just skips X2APIC
initialization without checking max CPU APIC ID in system, which may
cause problem if system has a CPU with APIC ID bigger than 255.
Handle IR in XAPIC mode the same way as if remapping is disabled.
[ tglx: Split out from previous patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refine enable_IR_x2apic() and related functions for better readability.
[ tglx: Removed the XAPIC mode change and split it out into a seperate
patch. Added comments. ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
X2APIC will be disabled if user specifies "nox2apic" on kernel command
line, even when x2apic_preenabled is true. So correctly detect X2APIC
status by using x2apic_enabled() instead of x2apic_preenabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-7-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Local variable x2apic_enabled has been assigned to but never referred,
so kill it.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-6-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When kernel doesn't support X2APIC but BIOS has enabled X2APIC, system
may panic or hang without useful messages. On the other hand, it's
hard to dynamically disable X2APIC when CONFIG_X86_X2APIC is disabled.
So panic with a clear message in such a case.
Now system panics as below when X2APIC is disabled and interrupt remapping
is enabled:
[ 0.316118] LAPIC pending interrupts after 512 EOI
[ 0.322126] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.368655] Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC
[ 0.378300] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.18.0+ #340
[ 0.385300] Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRIVTIN1.86B.0051.L05.1406240953 06/24/2014
[ 0.396997] ffff88046dc03000 ffff88046c307dd8 ffffffff8179dada 00000000000043f2
[ 0.405629] ffffffff81a92158 ffff88046c307e58 ffffffff8179b757 0000000000000002
[ 0.414261] 0000000000000008 ffff88046c307e68 ffff88046c307e08 ffffffff813ad82b
[ 0.422890] Call Trace:
[ 0.425711] [<ffffffff8179dada>] dump_stack+0x45/0x57
[ 0.431533] [<ffffffff8179b757>] panic+0xc1/0x1f5
[ 0.436978] [<ffffffff813ad82b>] ? delay_tsc+0x3b/0x70
[ 0.442910] [<ffffffff8166fa2c>] panic_if_irq_remap+0x1c/0x20
[ 0.449524] [<ffffffff81d73645>] setup_IO_APIC+0x405/0x82e
[ 0.464979] [<ffffffff81d6fcc2>] native_smp_prepare_cpus+0x2d9/0x31c
[ 0.472274] [<ffffffff81d5d0ac>] kernel_init_freeable+0xd6/0x223
[ 0.479170] [<ffffffff81792ad0>] ? rest_init+0x80/0x80
[ 0.485099] [<ffffffff81792ade>] kernel_init+0xe/0xf0
[ 0.490932] [<ffffffff817a537c>] ret_from_fork+0x7c/0xb0
[ 0.497054] [<ffffffff81792ad0>] ? rest_init+0x80/0x80
[ 0.502983] ---[ end Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC
System hangs as below when X2APIC and interrupt remapping are both disabled:
[ 1.102782] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 1.109351] pci 0000:00:03.0: System wakeup disabled by ACPI
[ 1.115915] pci 0000:00:03.2: System wakeup disabled by ACPI
[ 1.122479] pci 0000:00:03.3: System wakeup disabled by ACPI
[ 1.132274] pci 0000:00:1c.0: Enabling MPC IRBNCE
[ 1.137620] pci 0000:00:1c.0: Intel PCH root port ACS workaround enabled
[ 1.145239] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 1.151790] pci 0000:00:1c.7: Enabling MPC IRBNCE
[ 1.157128] pci 0000:00:1c.7: Intel PCH root port ACS workaround enabled
[ 1.164748] pci 0000:00:1c.7: System wakeup disabled by ACPI
[ 1.171447] pci 0000:00:1e.0: System wakeup disabled by ACPI
[ 1.178612] acpiphp: Slot [8] registered
[ 1.183095] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 1.188867] acpiphp: Slot [2] registered
With this patch applied, the system panics in both cases with a proper
panic message.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Link: http://lkml.kernel.org/r/1420615903-28253-5-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If x2apic got disabled on the kernel command line, then the following
issue can happen:
enable_IR_x2apic()
....
x2apic_mode = 1;
enable_x2apic();
if (x2apic_disabled) {
__disable_x2apic();
return;
}
That leaves X2APIC disabled in hardware, but x2apic_mode stays 1. So
all other code which checks x2apic_mode gets the wrong information.
Set x2apic_mode to 0 after disabling it in hardware.
This is just a hotfix. The proper solution is to rework this code so
it has seperate functions for the initial setup on the boot processor
and the secondary cpus, but that's beyond the scope of this fix.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
enable_IR_x2apic() calls setup_irq_remapping_ops() which by default
installs the intel dmar remapping ops and then calls the amd iommu irq
remapping prepare callback to figure out whether we are running on an
AMD machine with irq remapping hardware.
Right after that it calls irq_remapping_prepare() which pointlessly
checks:
if (!remap_ops || !remap_ops->prepare)
return -ENODEV;
and then calls
remap_ops->prepare()
which is silly in the AMD case as it got called from
setup_irq_remapping_ops() already a few microseconds ago.
Simplify this and just collapse everything into
irq_remapping_prepare().
The irq_remapping_prepare() remains still silly as it assigns blindly
the intel ops, but that's not scope of this patch.
The scope here is to move the preperatory work, i.e. memory
allocations out of the atomic section which is required to enable irq
remapping.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Acked-and-tested-by: Joerg Roedel <joro@8bytes.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <jroedel@suse.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oren Twaig <oren@scalemp.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141205084147.232633738@linutronix.de
Link: http://lkml.kernel.org/r/1420615903-28253-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
At the moment, if p and x are both tagged as bitwise types,
some of get_user(x, p), put_user(x, p), __get_user(x, p), __put_user(x, p)
might produce a sparse warning on many architectures.
This is a false positive: *p on these architectures is loaded into long
(typically using asm), then cast back to typeof(*p).
When typeof(*p) is a bitwise type (which is uncommon), such a cast needs
__force, otherwise sparse produces a warning.
Some architectures already have the __force tag, add it
where it's missing.
I verified that adding these __force casts does not supress any useful warnings.
Specifically, vhost wants to read/write bitwise types in userspace memory
using get_user/put_user.
At the moment this triggers sparse errors, since the value is passed through an
integer.
For example:
__le32 __user *p;
__u32 x;
both
put_user(x, p);
and
get_user(x, p);
should be safe, but produce warnings on some architectures.
While there, I noticed that a bunch of architectures violated
coding style rules within uaccess macros.
Included patches to fix them up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUtS+YAAoJECgfDbjSjVRpQ/QIAKXOc6tMXo+r/F32YC0Fv74G
W4VKIk7u9XQNjOzez9i+xce75YBDBKHk5R9kLCfAg6Zew+6NRgbBV+QjGVB8dpot
2GxajcVhOySgaR45sGK3Ldg5yVz5ficqZEyYWKNgYeyMWJdlpvUk+4W5q15TiPZe
u+C57/KzfRMDHyv3UkwAbqrkYGE0h7vXBi0BmOdCJlbKjG+6kFoVU/dAWsByDD5p
q54ji8UdIkh2oyH5qhSbAwQN4Cg5N37Agw86HwltjQFJAVvV3yPRUsv7MQnpRB1+
hKlPXPUarNozGVV7OlcvGa9Lvz8m3a2rNd9+1tgHY0Fpia1JYAY2UdubS99fl5E=
=LVcN
-----END PGP SIGNATURE-----
Merge tag 'uaccess_for_upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost into asm-generic
Merge "uaccess: fix sparse warning on get/put_user for bitwise types" from Michael S. Tsirkin:
At the moment, if p and x are both tagged as bitwise types,
some of get_user(x, p), put_user(x, p), __get_user(x, p), __put_user(x, p)
might produce a sparse warning on many architectures.
This is a false positive: *p on these architectures is loaded into long
(typically using asm), then cast back to typeof(*p).
When typeof(*p) is a bitwise type (which is uncommon), such a cast needs
__force, otherwise sparse produces a warning.
Some architectures already have the __force tag, add it
where it's missing.
I verified that adding these __force casts does not supress any useful warnings.
Specifically, vhost wants to read/write bitwise types in userspace memory
using get_user/put_user.
At the moment this triggers sparse errors, since the value is passed through an
integer.
For example:
__le32 __user *p;
__u32 x;
both
put_user(x, p);
and
get_user(x, p);
should be safe, but produce warnings on some architectures.
While there, I noticed that a bunch of architectures violated
coding style rules within uaccess macros.
Included patches to fix them up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'uaccess_for_upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (37 commits)
sparc32: nocheck uaccess coding style tweaks
sparc64: nocheck uaccess coding style tweaks
xtensa: macro whitespace fixes
sh: macro whitespace fixes
parisc: macro whitespace fixes
m68k: macro whitespace fixes
m32r: macro whitespace fixes
frv: macro whitespace fixes
cris: macro whitespace fixes
avr32: macro whitespace fixes
arm64: macro whitespace fixes
arm: macro whitespace fixes
alpha: macro whitespace fixes
blackfin: macro whitespace fixes
sparc64: uaccess_64 macro whitespace fixes
sparc32: uaccess_32 macro whitespace fixes
avr32: whitespace fix
sh: fix put_user sparse errors
metag: fix put_user sparse errors
ia64: fix put_user sparse errors
...
These patches fix the RFC4106 implementation in the aesni-intel
module so it supports 192 & 256 bit keys.
Since the AVX support that was added to this module also only
supports 128 bit keys, and this patch only affects the SSE
implementation, changes were also made to use the SSE version
if key sizes other than 128 are specified.
RFC4106 specifies that 192 & 256 bit keys must be supported (section
8.4).
Also, this should fix Strongswan issue 341 where the aesni module
needs to be unloaded if 256 bit keys are used:
http://wiki.strongswan.org/issues/341
This patch has been tested with Sandy Bridge and Haswell processors.
With 128 bit keys and input buffers > 512 bytes a slight performance
degradation was noticed (~1%). For input buffers of less than 512
bytes there was no performance impact. Compared to 128 bit keys,
256 bit key size performance is approx. .5 cycles per byte slower
on Sandy Bridge, and .37 cycles per byte slower on Haswell (vs.
SSE code).
This patch has also been tested with StrongSwan IPSec connections
where it worked correctly.
I created this diff from a git clone of crypto-2.6.git.
Any questions, please feel free to contact me.
Signed-off-by: Timothy McCaffrey <timothy.mccaffrey@unisys.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No code changes.
This is a preparatory patch for change in "struct pt_regs" handling.
CC: Linus Torvalds <torvalds@linux-foundation.org>
CC: Oleg Nesterov <oleg@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: X86 ML <x86@kernel.org>
CC: Alexei Starovoitov <ast@plumgrid.com>
CC: Will Drewry <wad@chromium.org>
CC: Kees Cook <keescook@chromium.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
The values of these two constants are the same, the meaning is different.
Acked-by: Borislav Petkov <bp@suse.de>
CC: Linus Torvalds <torvalds@linux-foundation.org>
CC: Oleg Nesterov <oleg@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Borislav Petkov <bp@alien8.de>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: X86 ML <x86@kernel.org>
CC: Alexei Starovoitov <ast@plumgrid.com>
CC: Will Drewry <wad@chromium.org>
CC: Kees Cook <keescook@chromium.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
A define, two macros and an unreferenced bit of assembly are gone.
Acked-by: Borislav Petkov <bp@suse.de>
CC: Linus Torvalds <torvalds@linux-foundation.org>
CC: Oleg Nesterov <oleg@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: X86 ML <x86@kernel.org>
CC: Alexei Starovoitov <ast@plumgrid.com>
CC: Will Drewry <wad@chromium.org>
CC: Kees Cook <keescook@chromium.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
- Several critical linear p2m fixes that prevented some hosts from
booting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUtQHNAAoJEFxbo/MsZsTR/qgH/iiW4k2T8dBGZ7TPyzt88iyT
4caWjuujp2OUaRqhBQdY7z05uai6XxgJLwDyqiO+qHaRUj+ZWCrjh/ZFPU1+09hK
GdwPMWU7xMRs/7F2ANO03jJ/ktvsYXtazcVrV89Q3t+ZZJIQ/THovDkaoa+dF2lh
W8d5H7N2UNCJLe9w2fm5iOq4SKoTsJOq6pVQ6gUBqJcgkSDWavd6bowXnTlcepZN
tNaSMZsOt4CAvYQIa0nKPJo6Q4QN3buRQMWEOAOmGVT/RkVi68wirwk59uNzcS7E
HjhqxFjhXYamNTuwHYZlchBrZutdbymSlucVucb1wAoxRAX+Wd1jk5EPl6zLv4w=
=kFSE
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
"Several critical linear p2m fixes that prevented some hosts from
booting"
* tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: properly retrieve NMI reason
xen: check for zero sized area when invalidating memory
xen: use correct type for physical addresses
xen: correct race in alloc_p2m_pmd()
xen: correct error for building p2m list on 32 bits
x86/xen: avoid freeing static 'name' when kasprintf() fails
x86/xen: add extra memory for remapped frames during setup
x86/xen: don't count how many PFNs are identity mapped
x86/xen: Free bootmem in free_p2m_page() during early boot
x86/xen: Remove unnecessary BUG_ON(preemptible()) in xen_setup_timer()
Pass the original kprobe for preparing an optimized kprobe arch-dep
part, since for some architecture (e.g. ARM32) requires the information
in original kprobe.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
virtio wants to read bitwise types from userspace using get_user. At the
moment this triggers sparse errors, since the value is passed through an
integer.
Fix that up using __force.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
This module implements variations of "des3_ede" only. Drop the bogus
module aliases for "des".
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 5d26a105b5 ("crypto: prefix module autoloading with "crypto-"")
changed the automatic module loading when requesting crypto algorithms
to prefix all module requests with "crypto-". This requires all crypto
modules to have a crypto specific module alias even if their file name
would otherwise match the requested crypto algorithm.
Even though commit 5d26a105b5 added those aliases for a vast amount of
modules, it was missing a few. Add the required MODULE_ALIAS_CRYPTO
annotations to those files to make them get loaded automatically, again.
This fixes, e.g., requesting 'ecb(blowfish-generic)', which used to work
with kernels v3.18 and below.
Also change MODULE_ALIAS() lines to MODULE_ALIAS_CRYPTO(). The former
won't work for crypto modules any more.
Fixes: 5d26a105b5 ("crypto: prefix module autoloading with "crypto-"")
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using the native code here can't work properly, as the hypervisor would
normally have cleared the two reason bits by the time Dom0 gets to see
the NMI (if passed to it at all). There's a shared info field for this,
and there's an existing hook to use - just fit the two together. This
is particularly relevant so that NMIs intended to be handled by APEI /
GHES actually make it to the respective handler.
Note that the hook can (and should) be used irrespective of whether
being in Dom0, as accessing port 0x61 in a DomU would be even worse,
while the shared info field would just hold zero all the time. Note
further that hardware NMI handling for PVH doesn't currently work
anyway due to missing code in the hypervisor (but it is expected to
work the native rather than the PV way).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
With the introduction of the linear mapped p2m list setting memory
areas to "invalid" had to be delayed. When doing the invalidation
make sure no zero sized areas are processed.
Signed-off-by: Juegren Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When converting a pfn to a physical address be sure to use 64 bit
wide types or convert the physical address to a pfn if possible.
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
When allocating a new pmd for the linear mapped p2m list a check is
done for not introducing another pmd when this just happened on
another cpu. In this case the old pte pointer was returned which
points to the p2m_missing or p2m_identity page. The correct value
would be the pointer to the found new page.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
In xen_rebuild_p2m_list() for large areas of invalid or identity
mapped memory the pmd entries on 32 bit systems are initialized
wrong. Correct this error.
Suggested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix
with certain odd memory mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Use asm volatile in __getcpu
x86/build: Clean auto-generated processor feature files
x86: Fix mkcapflags.sh bash-ism
x86: Fix step size adjustment during initial memory mapping
x86_64, vdso: Fix the vdso address randomization algorithm
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also some kernel side fixes: uncore PMU
driver fix, user regs sampling fix and an instruction decoder fix that
unbreaks PEBS precise sampling"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
perf/x86_64: Improve user regs sampling
perf: Move task_pt_regs sampling into arch code
x86: Fix off-by-one in instruction decoder
perf hists browser: Fix segfault when showing callchain
perf callchain: Free callchains when hist entries are deleted
perf hists: Fix children sort key behavior
perf diff: Fix to sort by baseline field by default
perf list: Fix --raw-dump option
perf probe: Fix crash in dwarf_getcfi_elf
perf probe: Fix to fall back to find probe point in symbols
perf callchain: Append callchains only when requested
perf ui/tui: Print backtrace symbols when segfault occurs
perf report: Show progress bar for output resorting
dmesg (from util-linux) currently has two methods for reading the kernel
message ring buffer: /dev/kmsg and syslog(2). Since kernel 3.5.0 kmsg
has been the default, which escapes control characters (e.g. new lines)
before they are shown.
This change means that when dmesg is using /dev/kmsg, a 2 line printk
makes the output messy, because the second line does not get a
timestamp.
For example:
[ 0.012863] CPU0: Thermal monitoring enabled (TM1)
[ 0.012869] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[ 0.012958] Freeing SMP alternatives memory: 28K (ffffffff81d86000 - ffffffff81d8d000)
[ 0.014961] dmar: Host address width 39
Because printk.c intentionally escapes control characters, they should
not be there in the first place. This patch fixes two occurrences of
this.
Signed-off-by: Steven Honeyman <stevenhoneyman@gmail.com>
Link: https://lkml.kernel.org/r/1414856696-8094-1-git-send-email-stevenhoneyman@gmail.com
[ Boris: make cpu_detect_tlb() static, while at it. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The macros cc-version, cc-fullversion and ld-version take no argument.
It is not necessary to add $(call ...) to invoke them.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Helge Deller <deller@gmx.de> [parisc]
Signed-off-by: Michal Marek <mmarek@suse.cz>
There was another report of a boot failure with a #GP fault in the
uncore SBOX initialization. The earlier work around was not enough
for this system.
The boot was failing while trying to initialize the third SBOX.
This patch detects parts with only two SBOXes and limits the number
of SBOX units to two there.
Stable material, as it affects boot problems on 3.18.
Tested-by: Andreas Oehler <andreas@oehler-net.de>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yan, Zheng <zheng.z.yan@intel.com>
Link: http://lkml.kernel.org/r/1420583675-9163-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Perf reports user regs for kernel-mode samples so that samples can
be backtraced through user code. The old code was very broken in
syscall context, resulting in useless backtraces.
The new code, in contrast, is still dangerously racy, but it should
at least work most of the time.
Tested-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: chenggang.qcg@taobao.com
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/243560c26ff0f739978e2459e203f6515367634d.1420396372.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On x86_64, at least, task_pt_regs may be only partially initialized
in many contexts, so x86_64 should not use it without extra care
from interrupt context, let alone NMI context.
This will allow x86_64 to override the logic and will supply some
scratch space to use to make a cleaner copy of user regs.
Tested-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: chenggang.qcg@taobao.com
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jean Pihet <jean.pihet@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/e431cd4c18c2e1c44c774f10758527fb2d1025c4.1420396372.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Stephane reported that the PEBS fixup was broken by the recent commit to
the instruction decoder. The thing had an off-by-one which resulted in
not being able to decode the last instruction and always bail.
Reported-by: Stephane Eranian <eranian@google.com>
Fixes: 6ba48ff46f ("x86: Remove arbitrary instruction size limit in instruction decoder")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org # 3.18
Cc: <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Liang Kan <kan.liang@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/20141216104614.GV3337@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are aborting a build in case when gcc doesn't support fentry on x86_64
(regs->ip modification can't really reliably work with mcount).
This however breaks allmodconfig for people with older gccs that don't
support -mfentry.
Turn the build-time failure into runtime failure, resulting in the whole
infrastructure not being initialized if CC_USING_FENTRY is unset.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
When emulating an instruction that reads the destination memory operand (i.e.,
instructions without the Mov flag in the emulator), the operand is first read.
If a page-fault is detected in this phase, the error-code which would be
delivered to the VM does not indicate that the access that caused the exception
is a write one. This does not conform with real hardware, and may cause the VM
to enter the page-fault handler twice for no reason (once for read, once for
write).
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When software changes D bit (either from 1 to 0, or 0 to 1), the
corresponding TLB entity in the hardware won't be updated immediately. We
should flush it to guarantee the consistence of D bit between TLB and
MMU page table in memory. This is especially important when clearing
the D bit, since it may cause false negatives in reporting dirtiness.
Sanity test was done on my machine with Intel processor.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
[Check A bit too. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Fix ACPI power management intialization for device objects
corresponding to devices that are not present at the init time
(the _STA control method returns 0 for them) and therefore should
not be regarded as power manageable (Rafael J Wysocki).
- Rename a structure field and two functions used by the ACPI
processor driver to make them less tied to architectures that
use APICs (both x86 and ia64) and more suitable for ARM64
processors (Hanjun Guo).
- Add a disable_native_backlight quirk for Dell XPS15 L521X
designed in an unusual way preventing native backlight from
working on that machine (Hans de Goede).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=NEY0
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are an ACPI device power management initialization fix (-stable
material), two commits renaming stuff in the ACPI processor driver to
make it more suitable for ARM64 processors and a new ACPI backlight
blacklist entry.
Specifics:
- Fix ACPI power management intialization for device objects
corresponding to devices that are not present at the init time (the
_STA control method returns 0 for them) and therefore should not be
regarded as power manageable (Rafael J Wysocki).
- Rename a structure field and two functions used by the ACPI
processor driver to make them less tied to architectures that use
APICs (both x86 and ia64) and more suitable for ARM64 processors
(Hanjun Guo).
- Add a disable_native_backlight quirk for Dell XPS15 L521X designed
in an unusual way preventing native backlight from working on that
machine (Hans de Goede)"
* tag 'pm+acpi-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Add disable_native_backlight quirk for Dell XPS15 L521X
ACPI / processor: Rename acpi_(un)map_lsapic() to acpi_(un)map_cpu()
ACPI / processor: Convert apic_id to phys_id to make it arch agnostic
ACPI / PM: Fix PM initialization for devices that are not present
Adds a function kvm_vcpu_set_pending_timer instead of calling
kvm_make_request in lapic.c.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When access to descriptor in LDT/GDT wraparound outside long-mode, the address
of the descriptor should be truncated to 32-bit. Citing Intel SDM 2.1.1.1
"Global and Local Descriptor Tables in IA-32e Mode": "GDTR and LDTR registers
are expanded to 64-bits wide in both IA-32e sub-modes (64-bit mode and
compatibility mode)."
So in other cases, we need to truncate. Creating new function to return a
pointer to descriptor table to avoid too much code duplication.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Wrap 64-bit check with #ifdef CONFIG_X86_64, to avoid a "right shift count
>= width of type" warning and consequent undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When segment is loaded, the segment access bit is set unconditionally. In
fact, it should be set conditionally, based on whether the segment had the
accessed bit set before. In addition, it can improve performance.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to Intel SDM: "If the ESP register is used as a base register for
addressing a destination operand in memory, the POP instruction computes the
effective address of the operand after it increments the ESP register."
The current emulation does not behave so. The fix required to waste another
of the precious instruction flags and to check the flag in decode_modrm.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, if em_call_far fails it returns success instead of the resulting
error-code. Fix it.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVM emulator does not emulate JMP and CALL that target a call gate or a
task gate. This patch does not try to implement these scenario as they are
presumably rare; yet it returns X86EMUL_UNHANDLEABLE error in such cases
instead of generating an exception.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the operand size of fnstcw and fnstsw is updated during the execution,
the emulation may cause spurious exceptions as it reads the memory beforehand.
Marking these instructions as Mov (since the previous value is ignored) and
DstMem16 to simplify the setting of operand size.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Although pop sreg updates RSP according to the operand size, only 2 bytes are
read. The current behavior may result in incorrect #GP or #PF exceptions.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because ASSERT is just a printk, these would oops right away.
The assertion thus hardly adds anything.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The initialization function in mmu.c can always use walk_mmu, which
is known to be vcpu->arch.mmu. Only init_kvm_nested_mmu is used to
initialize vcpu->arch.nested_mmu.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add tracepoint to wait_lapic_expire.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
[Remind reader if early or late. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the hrtimer which emulates the tscdeadline timer in the guest,
add an option to advance expiration, and busy spin on VM-entry waiting
for the actual expiration time to elapse.
This allows achieving low latencies in cyclictest (or any scenario
which requires strict timing regarding timer expiration).
Reduces average cyclictest latency from 12us to 8us
on Core i5 desktop.
Note: this option requires tuning to find the appropriate value
for a particular hardware/guest combination. One method is to measure the
average delay between apic_timer_fn and VM-entry.
Another method is to start with 1000ns, and increase the value
in say 500ns increments until avg cyclictest numbers stop decreasing.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_x86_ops->test_posted_interrupt() returns true/false depending
whether 'vector' is set.
Next patch makes use of this interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases calling hwapic_isr_update(), we always check if
kvm_apic_vid_enabled() == 1, but actually,
kvm_apic_vid_enabled()
-> kvm_x86_ops->vm_has_apicv()
-> vmx_vm_has_apicv() or '0' in svm case
-> return enable_apicv && irqchip_in_kernel(kvm)
So its a little cost to recall vmx_vm_has_apicv() inside
hwapic_isr_update(), here just NULL out hwapic_isr_update() in
case of !enable_apicv inside hardware_setup() then make all
related stuffs follow this. Note we don't check this under that
condition of irqchip_in_kernel() since we should make sure
definitely any caller don't work without in-kernel irqchip.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove FIXME comments about needing fault addresses to be returned. These
are propaagated from walk_addr_generic to gva_to_gpa and from there to
ops->read_std and ops->write_std.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When generating #PF VM-exit, check equality:
(PFEC & PFEC_MASK) == PFEC_MATCH
If there is equality, the 14 bit of exception bitmap is used to take decision
about generating #PF VM-exit. If there is inequality, inverted 14 bit is used.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch improve checks required by Intel Software Developer Manual.
- SMM MSRs are not allowed.
- microcode MSRs are not allowed.
- check x2apic MSRs only when LAPIC is in x2apic mode.
- MSR switch areas must be aligned to 16 bytes.
- address of first and last byte in MSR switch areas should not set any bits
beyond the processor's physical-address width.
Also it adds warning messages on failures during MSR switch. These messages
are useful for people who debug their VMMs in nVMX.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several hypervisors need MSR auto load/restore feature.
We read MSRs from VM-entry MSR load area which specified by L1,
and load them via kvm_set_msr in the nested entry.
When nested exit occurs, we get MSRs via kvm_get_msr, writing
them to L1`s MSR store area. After this, we read MSRs from VM-exit
MSR load area, and load them via kvm_set_msr.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull crypto fixes from Herbert Xu:
"This fixes a build problem with sha-mb with old toolchains and an
implementation bug in the ctr(aes)/by8 branch of aesni-intel that's
enabled when AVX is available"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sha-mb - Add avx2_supported check.
crypto: aesni - fix "by8" variant for 128 bit keys
In case kasprintf() fails in xen_setup_timer() we assign name to the
static string "<timer kasprintf failed>". We, however, don't check
that fact before issuing kfree() in xen_teardown_timer(), kernel is
supposed to crash with 'kernel BUG at mm/slub.c:3341!'
Solve the issue by making name a fixed length string inside struct
xen_clock_event_device. 16 bytes should be enough.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
If the non-RAM regions in the e820 memory map are larger than the size
of the initial balloon, a BUG was triggered as the frames are remaped
beyond the limit of the linear p2m. The frames are remapped into the
initial balloon area (xen_extra_mem) but not enough of this is
available.
Ensure enough extra memory regions are added for these remapped
frames.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
This accounting is just used to print a diagnostic message that isn't
very useful.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
With recent changes in p2m we now have legitimate cases when
p2m memory needs to be freed during early boot (i.e. before
slab is initialized).
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
There are more that one SPI controller on the Intel MID boards. This patch
describes the status and IDs of them. From now on we also have to care about
bus number that must be unique per host.
According to the specification the SPI1 has 5 bits for chip selects and SPI2
only 2 bits. The patch makes it depend to PCI ID.
The first controller (SPI1) is DMA capable, meanwhile SPI2 can share same
channels (via software switch) such functionality is not in the scope of this
patch. Thus, attempt to init DMA for SPI2 will always fail for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We now switch to the kernel stack when a machine check interrupts
during user mode. This means that we can perform recovery actions
in the tail of do_machine_check()
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
* acpi-pm:
ACPI / PM: Fix PM initialization for devices that are not present
* acpi-processor:
ACPI / processor: Rename acpi_(un)map_lsapic() to acpi_(un)map_cpu()
ACPI / processor: Convert apic_id to phys_id to make it arch agnostic
* acpi-video:
ACPI / video: Add disable_native_backlight quirk for Dell XPS15 L521X
SRCU is not necessary to be compiled by default in all cases. For tinification
efforts not compiling SRCU unless necessary is desirable.
The current patch tries to make compiling SRCU optional by introducing a new
Kconfig option CONFIG_SRCU which is selected when any of the components making
use of SRCU are selected.
If we do not select CONFIG_SRCU, srcu.o will not be compiled at all.
text data bss dec hex filename
2007 0 0 2007 7d7 kernel/rcu/srcu.o
Size of arch/powerpc/boot/zImage changes from
text data bss dec hex filename
831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before
829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after
so the savings are about ~2000 bytes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
acpi_map_lsapic() will allocate a logical CPU number and map it to
physical CPU id (such as APIC id) for the hot-added CPU, it will also
do some mapping for NUMA node id and etc, acpi_unmap_lsapic() will
do the reverse.
We can see that the name of the function is a little bit confusing and
arch (IA64) dependent so rename them as acpi_(un)map_cpu() to make arch
agnostic and explicit.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes this allyesconfig target build error with older
binutils.
LD arch/x86/crypto/built-in.o
ld: arch/x86/crypto/sha-mb/built-in.o: No such file: No such file or directory
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Vinson Lee <vlee@twitter.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "by8" counter mode optimization is broken for 128 bit keys with
input data longer than 128 bytes. It uses the wrong key material for
en- and decryption.
The key registers xkey0, xkey4, xkey8 and xkey12 need to be preserved
in case we're handling more than 128 bytes of input data -- they won't
get reloaded after the initial load. They must therefore be (a) loaded
on the first iteration and (b) be preserved for the latter ones. The
implementation for 128 bit keys does not comply with (a) nor (b).
Fix this by bringing the implementation back to its original source
and correctly load the key registers and preserve their values by
*not* re-using the registers for other purposes.
Kudos to James for reporting the issue and providing a test case
showing the discrepancies.
Reported-by: James Yonan <james@openvpn.net>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit a074335a37 ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.
Before:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 D sys_call_table
0000000000000000 D syscall_table_size
After:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 R sys_call_table
0000000000000000 D syscall_table_size
Fixes: a074335a37 ("x86, um: Mark system call tables readonly")
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
In some IST handlers, if the interrupt came from user mode,
we can safely enable preemption. Add helpers to do it safely.
This is intended to be used my the memory failure code in
do_machine_check.
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
There's no good reason for it to be a macro, and x86_64 will want to
use it, so it should be in a header.
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
We currently pretend that IST context is like standard exception
context, but this is incorrect. IST entries from userspace are like
standard exceptions except that they use per-cpu stacks, so they are
atomic. IST entries from kernel space are like NMIs from RCU's
perspective -- they are not quiescent states even if they
interrupted the kernel during a quiescent state.
Add and use ist_enter and ist_exit to track IST context. Even
though x86_32 has no IST stacks, we track these interrupts the same
way.
This fixes two issues:
- Scheduling from an IST interrupt handler will now warn. It would
previously appear to work as long as we got lucky and nothing
overwrote the stack frame. (I don't know of any bugs in this
that would trigger the warning, but it's good to be on the safe
side.)
- RCU handling in IST context was dangerous. As far as I know,
only machine checks were likely to trigger this, but it's good to
be on the safe side.
Note that the machine check handlers appears to have been missing
any context tracking at all before this patch.
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
This causes all non-NMI, non-double-fault kernel entries from
userspace to run on the normal kernel stack. Double-fault is
exempt to minimize confusion if we double-fault directly from
userspace due to a bad kernel stack.
This is, suprisingly, simpler and shorter than the current code. It
removes the IMO rather frightening paranoid_userspace path, and it
make sync_regs much simpler.
There is no risk of stack overflow due to this change -- the kernel
stack that we switch to is empty.
This will also enable us to create non-atomic sections within
machine checks from userspace, which will simplify memory failure
handling. It will also allow the upcoming fsgsbase code to be
simplified, because it doesn't need to worry about usergs when
scheduling in paranoid_exit, as that code no longer exists.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Use capital BIOS in comment. Its cleaner, and allows diference
between BIOS and BIOs.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
safe (it just adds a volatile).
I don't think it fixes an actual bug (the __getcpu calls in the
pvclock code may not have been needed in the first place), but
discussion on that point is ongoing.
It also fixes a big performance issue in 3.18 and earlier in which
the lsl instructions in vclock_gettime got hoisted so far up the
function that they happened even when the function they were in was
never called. n 3.19, the performance issue seems to be gone due to
the whims of my compiler and some interaction with a branch that's
now gone.
I'll hopefully have a much bigger overhaul of the pvclock code
for 3.20, but it needs careful review.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUmduGAAoJEK9N98ZeDfrk874H/RkkP+y6/DmdKVR1dTOUQW4u
f1wPU0/sc5xywGjNcfR3XwUuyBJyd3s81WVaE5XXHfCHnbjG2Z4CNTqga27hL1D0
io01Q2s3dh1Y5c0cccVmJmyw//YVzMUOzGTNM9R0NKQNXmYUz6jgQaqk+wWORdD6
JXCU3/LI5VT0fjNPLj1M9l59eC2Qg/V4GqY2xRJ1AfbwkX1CFZTcWUPb+4FScVYv
9gds/vOoFg54MypVJD4SeIC9I8U0qcim9gV7gGFdzyDNCXS5J4P+02sEOFNu8oYy
HVK1B0LXhswT08Ho1yRxXUhFxpqEGeGJvTlDTvwy+r/yuKE2AVBtlhLQBqMPhnY=
=u3d2
-----END PGP SIGNATURE-----
Merge tag 'pr-20141223-x86-vdso' of git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux into x86/urgent
Pull VDSO fix from Andy Lutomirski:
"This is hopefully the last vdso fix for 3.19. It should be very
safe (it just adds a volatile).
I don't think it fixes an actual bug (the __getcpu calls in the
pvclock code may not have been needed in the first place), but
discussion on that point is ongoing.
It also fixes a big performance issue in 3.18 and earlier in which
the lsl instructions in vclock_gettime got hoisted so far up the
function that they happened even when the function they were in was
never called. n 3.19, the performance issue seems to be gone due to
the whims of my compiler and some interaction with a branch that's
now gone.
I'll hopefully have a much bigger overhaul of the pvclock code
for 3.20, but it needs careful review."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since most virtual machines raise this message once, it is a bit annoying.
Make it KERN_DEBUG severity.
Cc: stable@vger.kernel.org
Fixes: 7a2e8aaf0f
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The commit 34a1cd60d1, "x86: vmx: move some vmx setting from
vmx_init() to hardware_setup()", tried to refactor some codes
specific to vmx hardware setting into hardware_setup(), but some
msr writing should depend on our previous setting condition like
enable_apicv, enable_ept and so on.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In Linux 3.18 and below, GCC hoists the lsl instructions in the
pvclock code all the way to the beginning of __vdso_clock_gettime,
slowing the non-paravirt case significantly. For unknown reasons,
presumably related to the removal of a branch, the performance issue
is gone as of
e76b027e64 x86,vdso: Use LSL unconditionally for vgetcpu
but I don't trust GCC enough to expect the problem to stay fixed.
There should be no correctness issue, because the __getcpu calls in
__vdso_vlock_gettime were never necessary in the first place.
Note to stable maintainers: In 3.18 and below, depending on
configuration, gcc 4.9.2 generates code like this:
9c3: 44 0f 03 e8 lsl %ax,%r13d
9c7: 45 89 eb mov %r13d,%r11d
9ca: 0f 03 d8 lsl %ax,%ebx
This patch won't apply as is to any released kernel, but I'll send a
trivial backported version if needed.
Fixes: 51c19b4f59 x86: vdso: pvclock gettime support
Cc: stable@vger.kernel.org # 3.8+
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Commit 9def39be4e ("x86: Support compiling out human-friendly
processor feature names") made two source file targets
conditional. Such conditional targets will not be cleaned
automatically by make mrproper.
Fix by adding explicit clean-files targets for the two files.
Fixes: 9def39be4e ("x86: Support compiling out human-friendly processor feature names")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/1419335863-10608-1-git-send-email-bjorn@mork.no
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The old scheme can lead to failure in certain cases - the
problem is that after bumping step_size the next (non-final)
iteration is only guaranteed to make available a memory block
the size of what step_size was before. E.g. for a memory block
[0,3004600000) we'd have:
iter start end step amount
1 3004400000 30045fffff 2M 2M
2 3004000000 30043fffff 64M 4M
3 3000000000 3003ffffff 2G 64M
4 2000000000 2fffffffff 64G 64G
Yet to map 64G with 4k pages (as happens e.g. under PV Xen) we
need slightly over 128M, but the first three iterations made
only about 70M available.
The condition (new_mapped_ram_size > mapped_ram_size) for
bumping step_size is just not suitable. Instead we want to bump
it when we know we have enough memory available to cover a block
of the new step_size. And rather than making that condition more
complicated than needed, simply adjust step_size by the largest
possible factor we know we can cover at that point - which is
shifting it left by one less than the difference between page
table level shifts. (Interestingly the original STEP_SIZE_SHIFT
definition had a comment hinting at that having been the
intention, just that it should have been PUD_SHIFT-PMD_SHIFT-1
instead of (PUD_SHIFT-PMD_SHIFT)/2, and of course for non-PAE
32-bit we can't really use these two constants as they're equal
there.)
Furthermore the comment in get_new_step_size() didn't get
updated when the bottom-down mapping logic got added. Yet while
an overflow (flushing step_size to zero) of the shift doesn't
matter for the top-down method, it does for bottom-up because
round_up(x, 0) = 0, and an upper range boundary of zero can't
really work well.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/54945C1E020000780005114E@mail.emea.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is no reason for having it and, with commit 250a1ac685 ("x86,
smpboot: Remove pointless preempt_disable() in
native_smp_prepare_cpus()"), it prevents HVM guests from booting.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Remove the function is_apbt_capable() that is not used anywhere.
This was partially found by using a static code analysis program
called 'cppcheck'.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1419166698-2470-1-git-send-email-rickard_strandqvist@spectrumdigital.se
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up the else-case in fpu_fxsave() which seems like it has
been overlooked. Correct comment style in restore_fpu_checking()
while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1419170543-11393-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The execution flow redirection related implemention in the livepatch
ftrace handler is depended on the specific architecture. This patch
introduces klp_arch_set_pc(like kgdb_arch_set_pc) interface to change
the pt_regs.
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This commit introduces code for the live patching core. It implements
an ftrace-based mechanism and kernel interface for doing live patching
of kernel and kernel module functions.
It represents the greatest common functionality set between kpatch and
kgraft and can accept patches built using either method.
This first version does not implement any consistency mechanism that
ensures that old and new code do not run together. In practice, ~90% of
CVEs are safe to apply in this way, since they simply add a conditional
check. However, any function change that can not execute safely with
the old version of the function can _not_ be safely applied in this
version.
[ jkosina@suse.cz: due to the number of contributions that got folded into
this original patch from Seth Jennings, add SUSE's copyright as well, as
discussed via e-mail ]
Signed-off-by: Seth Jennings <sjenning@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Petr Mladek <pmladek@suse.cz>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The vdso base address has always been randomized, and I don't think there's
anything particularly wrong with the range over which it's randomized,
but the implementation seems to have been buggy since the very beginning.
This fixes the implementation to remove a large bias that caused a small
fraction of possible vdso load addresess to be vastly more likely than
the rest of the possible addresses.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUlhwwAAoJEK9N98ZeDfrklIcH/2/4P/ffRcCp0qYo7gFpXwPh
bWem3ygB4xmBgiivwGJOx/GgE6/QGmedZmD6EDLoLmpuOvGjdp4iRmvU1dCSDWOE
bMOBa1cxC4TPGzqlbGgjmyHgMPuihJq6GInAqmpJk/hZJ8W7JfnXyoZbt9pj4UBW
gYKMLa0gSF/rMTZ5hkDQ6mVH65M7jJnmHLRydTpK8Ryfap2lu01MIr6mC6xaobVc
5NfbI8bZexQECGLmPsFRnFWrYXNz86PKtN0j4YnPRVPRbBSTi8nHGu+zK2CJXpgu
9hyZ0eOdqSEi4wwQgI9g9lZSsa1C+5QBc6BwiDy5XjToPJOx5EnT6+m9O+fy9Q8=
=BVMi
-----END PGP SIGNATURE-----
Merge tag 'pr-20141220-x86-vdso' of git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux into x86/urgent
Pull a VDSO fix from Andy Lutomirski:
"One vdso fix for a longstanding ASLR bug that's been in the news lately.
The vdso base address has always been randomized, and I don't think there's
anything particularly wrong with the range over which it's randomized,
but the implementation seems to have been buggy since the very beginning.
This fixes the implementation to remove a large bias that caused a small
fraction of possible vdso load addresess to be vastly more likely than
the rest of the possible addresses."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The theory behind vdso randomization is that it's mapped at a random
offset above the top of the stack. To avoid wasting a page of
memory for an extra page table, the vdso isn't supposed to extend
past the lowest PMD into which it can fit. Other than that, the
address should be a uniformly distributed address that meets all of
the alignment requirements.
The current algorithm is buggy: the vdso has about a 50% probability
of being at the very end of a PMD. The current algorithm also has a
decent chance of failing outright due to incorrect handling of the
case where the top of the stack is near the top of its PMD.
This fixes the implementation. The paxtest estimate of vdso
"randomisation" improves from 11 bits to 18 bits. (Disclaimer: I
don't know what the paxtest code is actually calculating.)
It's worth noting that this algorithm is inherently biased: the vdso
is more likely to end up near the end of its PMD than near the
beginning. Ideally we would either nix the PMD sharing requirement
or jointly randomize the vdso and the stack to reduce the bias.
In the mean time, this is a considerable improvement with basically
no risk of compatibility issues, since the allowed outputs of the
algorithm are unchanged.
As an easy test, doing this:
for i in `seq 10000`
do grep -P vdso /proc/self/maps |cut -d- -f1
done |sort |uniq -d
used to produce lots of output (1445 lines on my most recent run).
A tiny subset looks like this:
7fffdfffe000
7fffe01fe000
7fffe05fe000
7fffe07fe000
7fffe09fe000
7fffe0bfe000
7fffe0dfe000
Note the suspicious fe000 endings. With the fix, I get a much more
palatable 76 repeated addresses.
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
ACCESS_ONCE might fail with specific compilers for non-scalar accesses.
Here is a set of patches to tackle that problem.
The first patch introduce READ_ONCE and ASSIGN_ONCE. If the data structure
is larger than the machine word size memcpy is used and a warning is emitted.
The next patches fix up several in-tree users of ACCESS_ONCE on non-scalar
types.
This merge does not yet contain a patch that forces ACCESS_ONCE to work only
on scalar types. This is targetted for the next merge window as Linux next
already contains new offenders regarding ACCESS_ONCE vs. non-scalar types.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=IQ5o
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
"kernel: Provide READ_ONCE and ASSIGN_ONCE
As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
ACCESS_ONCE might fail with specific compilers for non-scalar
accesses.
Here is a set of patches to tackle that problem.
The first patch introduce READ_ONCE and ASSIGN_ONCE. If the data
structure is larger than the machine word size memcpy is used and a
warning is emitted. The next patches fix up several in-tree users of
ACCESS_ONCE on non-scalar types.
This does not yet contain a patch that forces ACCESS_ONCE to work only
on scalar types. This is targetted for the next merge window as Linux
next already contains new offenders regarding ACCESS_ONCE vs.
non-scalar types"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
s390/kvm: REPLACE barrier fixup with READ_ONCE
arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
mips/gup: Replace ACCESS_ONCE with READ_ONCE
x86/gup: Replace ACCESS_ONCE with READ_ONCE
x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
mm: replace ACCESS_ONCE with READ_ONCE or barriers
kernel: Provide READ_ONCE and ASSIGN_ONCE
This adds the SFI based cpu freq driver for some of the Intel's
Silvermont based Atom architectures like Z34xx and Z35xx.
Signed-off-by: Rudramuni, Vishwesh M <vishwesh.m.rudramuni@intel.com>
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
Pull x86 MPX fixes from Thomas Gleixner:
"Three updates for the new MPX infrastructure:
- Use the proper error check in the trap handler
- Add a proper config option for it
- Bring documentation up to date"
* 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mpx: Give MPX a real config option prompt
x86, mpx: Update documentation
x86_64/traps: Fix always true condition
Pull x86 fix from Ingo Molnar:
"This contains a single TLS ABI validation fix from Andy Lutomirski"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tls: Don't validate lm in set_thread_area() after all
Pull perf fixes and cleanups from Ingo Molnar:
"A kernel fix plus mostly tooling fixes, but also some tooling
restructuring and cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
perf: Fix building warning on ARM 32
perf symbols: Fix use after free in filename__read_build_id
perf evlist: Use roundup_pow_of_two
tools: Adopt roundup_pow_of_two
perf tools: Make the mmap length autotuning more robust
tools: Adopt rounddown_pow_of_two and deps
tools: Adopt fls_long and deps
tools: Move bitops.h from tools/perf/util to tools/
tools: Introduce asm-generic/bitops.h
tools lib: Move asm-generic/bitops/find.h code to tools/include and tools/lib
tools: Whitespace prep patches for moving bitops.h
tools: Move code originally from asm-generic/atomic.h into tools/include/asm-generic/
tools: Move code originally from linux/log2.h to tools/include/linux/
tools: Move __ffs implementation to tools/include/asm-generic/bitops/__ffs.h
perf evlist: Do not use hard coded value for a mmap_pages default
perf trace: Let the perf_evlist__mmap autosize the number of pages to use
perf evlist: Improve the strerror_mmap method
perf evlist: Clarify sterror_mmap variable names
perf evlist: Fixup brown paper bag on "hint" for --mmap-pages cmdline arg
perf trace: Provide a better explanation when mmap fails
...
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
- spring cleaning: removed support for IA64, and for hardware-assisted
virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken because
the (non-KVM) XSAVES patches inadvertently changed the KVM userspace
ABI whenever XSAVES was enabled; hence, this part is going to stable.
Guest support is just a matter of exposing the feature and CPUID leaves
support.
Right now KVM is broken for PPC BookE in your tree (doesn't compile).
I'll reply to the pull request with a patch, please apply it either
before the pull request or in the merge commit, in order to preserve
bisectability somewhat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUkpg+AAoJEL/70l94x66DUmoH/jzXYkptSW9NGgm79KqxGJlD
lzLnLBkitVvx++Mz5YBhdJEhKKLUlCtifFT1zPJQ/pthQhIRSaaAwZyNGgUs5w5x
yMGKHiPQFyZRbmQtZhCInW0BftJoYHHciO3nUfHCZnp34My9MP2D55W7/z+fYFfQ
DuqBSE9ThyZJtZ4zh8NRA9fCOeuqwVYRyoBs820Wbsh4cpIBoIK63Dg7k+CLE+ZV
MZa/mRL6bAfsn9W5bnOUAgHJ3SPznnWbO3/g0aV+roL/5pffblprJx9lKNR08xUM
6hDFLop2gDehDJesDkY/o8Ckp1hEouvfsVpSShry4vcgtn0hgh2O5/6Orbmj6vE=
=Zwq1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM update from Paolo Bonzini:
"3.19 changes for KVM:
- spring cleaning: removed support for IA64, and for hardware-
assisted virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken
because the (non-KVM) XSAVES patches inadvertently changed the KVM
userspace ABI whenever XSAVES was enabled; hence, this part is
going to stable. Guest support is just a matter of exposing the
feature and CPUID leaves support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (179 commits)
KVM: move APIC types to arch/x86/
KVM: PPC: Book3S: Enable in-kernel XICS emulation by default
KVM: PPC: Book3S HV: Improve H_CONFER implementation
KVM: PPC: Book3S HV: Fix endianness of instruction obtained from HEIR register
KVM: PPC: Book3S HV: Remove code for PPC970 processors
KVM: PPC: Book3S HV: Tracepoints for KVM HV guest interactions
KVM: PPC: Book3S HV: Simplify locking around stolen time calculations
arch: powerpc: kvm: book3s_paired_singles.c: Remove unused function
arch: powerpc: kvm: book3s_pr.c: Remove unused function
arch: powerpc: kvm: book3s.c: Remove some unused functions
arch: powerpc: kvm: book3s_32_mmu.c: Remove unused function
KVM: PPC: Book3S HV: Check wait conditions before sleeping in kvmppc_vcore_blocked
KVM: PPC: Book3S HV: ptes are big endian
KVM: PPC: Book3S HV: Fix inaccuracies in ICP emulation for H_IPI
KVM: PPC: Book3S HV: Fix KSM memory corruption
KVM: PPC: Book3S HV: Fix an issue where guest is paused on receiving HMI
KVM: PPC: Book3S HV: Fix computation of tlbie operand
KVM: PPC: Book3S HV: Add missing HPTE unlock
KVM: PPC: BookE: Improve irq inject tracepoint
arm/arm64: KVM: Require in-kernel vgic for the arch timers
...
It turns out that there's a lurking ABI issue. GCC, when
compiling this in a 32-bit program:
struct user_desc desc = {
.entry_number = idx,
.base_addr = base,
.limit = 0xfffff,
.seg_32bit = 1,
.contents = 0, /* Data, grow-up */
.read_exec_only = 0,
.limit_in_pages = 1,
.seg_not_present = 0,
.useable = 0,
};
will leave .lm uninitialized. This means that anything in the
kernel that reads user_desc.lm for 32-bit tasks is unreliable.
Revert the .lm check in set_thread_area(). The value never did
anything in the first place.
Fixes: 0e58af4e1d ("x86/tls: Disallow unusual TLS segments")
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # Only if 0e58af4e1d is backported
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/d7875b60e28c512f6a6fc0baf5714d58e7eaadbb.1418856405.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ACCESS_ONCE does not work reliably on non-scalar types. For
example gcc 4.6 and 4.7 might remove the volatile tag for such
accesses during the SRA (scalar replacement of aggregates) step
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145)
Change the gup code to replace ACCESS_ONCE with READ_ONCE.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
ACCESS_ONCE does not work reliably on non-scalar types. For
example gcc 4.6 and 4.7 might remove the volatile tag for such
accesses during the SRA (scalar replacement of aggregates) step
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145)
Change the spinlock code to replace ACCESS_ONCE with READ_ONCE.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
My commit 26178ec11e ("x86: mm: consolidate VM_FAULT_RETRY handling")
had a really stupid typo: the FAULT_FLAG_USER bit is in the 'flags'
variable, not the 'fault' variable. Duh,
The one silver lining in this is that Dave finding this at least
confirms that trinity actually triggers this special path easily, in a
way normal use does not.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Linear p2m for x86 PV guests which simplifies the p2m code, improves
performance and will allow for > 512 GB PV guests in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUjx7OAAoJEFxbo/MsZsTRXLIH/ishF/xDCL6F5r0I0SKDuaz5
C/BediDcFzbzh4/t3x2PrPooHk4gPmeyIg688ZGgBAxHRXC5OJ2U5tdtZ/qUCnwf
0J1pdp/yoAOVRJT+Sax10lN4+G8YV7+6Ptikz0C7glXBAg8SgFL3Y6tfBS0jNwYR
wQph09S9n7gMZTodSBLbb0ymtJMhl16DrETJsYV73sU7bAL5sFDVkMQvY3SxkusX
GNFeALfqM0cSK9mDI6O9avGJKoIdKlzt7VWHdlc+yKTlQsoyg/cSH3AaihhG6af9
IElRxwH9Z40VFLKip0gNMOIrUwAjFGSw6N+Uhik27tlmvfI3Dll/+gsMz/5sHc8=
=OyoK
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.19-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull additional xen update from David Vrabel:
"Xen: additional features for 3.19-rc0
- Linear p2m for x86 PV guests which simplifies the p2m code,
improves performance and will allow for > 512 GB PV guests in the
future.
A last-minute, configuration specific issue was discovered with this
change which is why it was not included in my previous pull request.
This is now been fixed and tested"
* tag 'stable/for-linus-3.19-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: switch to post-init routines in xen mmu.c earlier
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen: annotate xen_set_identity_and_remap_chunk() with __init
xen: introduce helper functions to do safe read and write accesses
xen: Speed up set_phys_to_machine() by using read-only mappings
xen: switch to linear virtual mapped sparse p2m list
xen: Hide get_phys_to_machine() to be able to tune common path
x86: Introduce function to get pmd entry pointer
xen: Delay invalidating extra memory
xen: Delay m2p_override initialization
xen: Delay remapping memory of pv-domain
xen: use common page allocation function in p2m.c
xen: Make functions static
xen: fix some style issues in p2m.c
Use helpers to access irq_cfg data structure associated with IRQ,
instead of accessing irq_data->chip_data directly. Later we can
rewrite those helpers to support hierarchy irqdomain.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414397531-28254-17-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now we have splitted functions to support MSI and HT_IRQ into vector.c,
and they have no dependency on IOAPIC any more. So change Kconfig files
to make MSI and HT_IRQ independent of X86_IO_APIC.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1414397531-28254-16-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Clean up code by moving IOAPIC related declarations from hw_irq.h into
io_apic.h.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Aubrey <aubrey.li@linux.intel.com>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Create arch/x86/kernel/apic/vector.c to host local APIC related code,
prepare for making MSI/HT_IRQ independent of IOAPIC.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1414397531-28254-10-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change irq_cfg() from static to extern, also introduce helper function
irqd_cfg(). Later we can rewrite these two helpers when enabling
hierarchy irqdomain.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1414397531-28254-9-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Function __clear_irq_vector() accesses vector related data structure,
so protect it with vector_lock. Also rename it as clear_irq_vector().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414397531-28254-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename local APIC related functions in io_apic.c as apic_xxx() instead
of ioapic_xxx(), later they will be moved into separate file.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1414397531-28254-7-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refine hw_irq.h to prepare for irqdomain support by:
1) guarding common APIC related interfaces with CONFIG_X86_LOCAL_APIC
2) guarding interrupt remapping related interfaces with CONFIG_IRQ_REMAP
3) guarding IOAPIC related interfaces with CONFIG_X86_IO_APIC
No functional changes.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414397531-28254-6-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use generic list to replace private list implementation so we can use
the existing helper functions.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1414397531-28254-5-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Joerg Roedel <joro@8bytes.org>
None of the callers requires irq_attr to be filled
in. IO_APIC_get_PCI_irq_vector() does not do anything useful with it
either.
Remove the parameter and fixup the call sites.
[ tglx: Massaged changelog ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The IOAPIC has logic to track IOAPIC pin status, so there's no need for
special treatment for GSI used by ACPI SCI in function mp_register_gsi()
and mp_unregister_gsi().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Link: http://lkml.kernel.org/r/1414397531-28254-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce acpi_ioapic_registered() to check whether an IOAPIC has already
been registered, it will be used when enabling IOAPIC hotplug.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414387308-27148-18-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement acpi_unregister_ioapic() to support ACPI based IOAPIC hot-removal.
An IOAPIC could only be removed when all its pins are unused.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414387308-27148-17-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement acpi_register_ioapic() and enhance mp_register_ioapic()
to support ACPI based IOAPIC hot-addition.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414387308-27148-16-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We are going to support ACPI based IOAPIC hotplug, so introduce a mutex
to protect IOAPIC data structures from IOAPIC hotplug. We choose to
serialize in ACPI instead of in the IOAPIC core because:
1) currently we only plan to support ACPI based IOAPIC hotplug
2) it's much more cleaner and easier
3) It does't affect IOAPIC discovered by devicetree, SFI and mpparse.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Link: http://lkml.kernel.org/r/1414908273-7552-15-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refine mp_register_ioapic() to prepare for IOAPIC hotplug by:
1) change return value from void to int.
2) check for gsi range conflicts
3) check for IOAPIC physical address conflicts
4) enhance the way to allocate IOAPIC index
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414387308-27148-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To keep balance of IOAPIC pin reference count, we need to protect
pirq_enable_irq(), acpi_pci_irq_enable() and intel_mid_pci_irq_enable()
from reentrance. There are two cases which will cause reentrance.
The first case is caused by suspend/hibernation. If pcibios_disable_irq
is called during suspending/hibernating, we don't release the assigned
IRQ number, otherwise it may break the suspend/hibernation. So late when
pcibios_enable_irq is called during resume, we shouldn't allocate IRQ
number again.
The second case is that function acpi_pci_irq_enable() may be called
twice for PCI devices present at boot time as below:
1) pci_acpi_init()
--> acpi_pci_irq_enable() if pci_routeirq is true
2) pci_enable_device()
--> pcibios_enable_device()
--> acpi_pci_irq_enable()
We can't kill kernel parameter pci_routeirq yet because it's still
needed for debugging purpose.
So flag irq_managed is introduced to track whether IRQ number is
assigned by OS and to protect pirq_enable_irq(), acpi_pci_irq_enable()
and intel_mid_pci_irq_enable() from reentrance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1414387308-27148-13-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove __init marker for functions which will be used by IOAPIC hotplug
at runtime.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414387308-27148-12-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Perfer the assigned ID in APIC ID register for x86_64 if it's still
available.
[ tglx: Added comments ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414387308-27148-11-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Split out alloc_ioapic_save_registers() from early_irq_init(),
so it could be used for ioapic hotplug later.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414387308-27148-10-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no reason to keep preemption disabled in this function.
We only have two other threads live: kthreadd and idle. Neither of
them is going to preempt. But that preempt_disable forces all the code
inside to do GFP_ATOMIC allocations which is just insane.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141205084147.153643952@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When X86_LOCAL_APIC (i.e. unconditionally on x86-64),
first_system_vector will never end up being higher than
LOCAL_TIMER_VECTOR (0xef), and hence building stubs for vectors
0xef...0xff is pointlessly reducing code density. Deal with this at
build time already.
Taking into consideration that X86_64 implies X86_LOCAL_APIC, also
simplify (and hence make easier to read and more consistent with the
change done here) some #if-s in arch/x86/kernel/irqinit.c.
While we could further improve the packing of the IRQ entry stubs (the
four ones now left in the last set could be fit into the four padding
bytes each of the final four sets have) this doesn't seem to provide
any real benefit: Both irq_entries_start and common_interrupt getting
cache line aligned, eliminating the 30th set would just produce 32
bytes of padding between the 29th and common_interrupt.
[ tglx: Folded lguest fix from Dan Carpenter ]
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: lguest@lists.ozlabs.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Link: http://lkml.kernel.org/r/54574D5F0200007800044389@mail.emea.novell.com
Link: http://lkml.kernel.org/r/20141115185718.GB6530@mwanda
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While f3761db164 ("x86, irq: Fix build error caused by
9eabc99a635a77cbf09") addressed the original build problem,
declaration, inline stub, and definition still seem misplaced: It isn't
really IO-APIC related, and it's being used solely in arch/x86/pci/.
This also means stubbing it out when !CONFIG_X86_IO_APIC was at least
questionable.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/545747BE020000780004436E@mail.emea.novell.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix building warning when CONFIG_X86_LOCAL_APIC is disabled.
arch/x86/kernel/acpi/boot.c:699:20: warning: ‘acpi_set_irq_model_ioapic’ defined but not used [-Wunused-function]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Link: http://lkml.kernel.org/r/1414397531-28254-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Define an empty send_cleanup_vector() for UP kernel to fix link error
of undefined reference, which is used by uv_irq and irq_remapping.
[ tglx: Made it an inline stub and moved it ahead of the file split
changes ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1414397531-28254-21-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
The VM_FAULT_RETRY handling was confusing and incorrect for the case of
returning to kernel mode. We need to handle the exception table fixup
if we return to kernel mode due to a fatal signal - it will basically
look to the kernel user mode access like the access failed due to the VM
going away from udner it. Which is correct - the process is dying - and
avoids the whole "repeat endless kernel page faults" case.
Handling the VM_FAULT_RETRY early and in just one place also simplifies
the mmap_sem handling, since once we've taken care of VM_FAULT_RETRY we
know that we can just drop the lock. The remaining accounting and
possible error handling is thread-local and does not need the mmap_sem.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This replaces four copies in various stages of mm_fault_error() handling
with just a single one. It will also allow for more natural placement
of the unlocking after some further cleanup.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some BIOSes utilize PCI MMCFG space read/write opertion to trigger
specific errors. EINJ will report errors as below when hitting such
cases:
APEI: Can not request [mem 0x83f990a0-0x83f990a3] for APEI EINJ Trigger registers
It is because on x86 platform ACPI based PCI MMCFG logic has
reserved all MMCFG spaces so that EINJ can't reserve it again.
We already trust the ACPI/APEI code when using the EINJ interface
so it is not a big leap to also trust it to access the right
MMCFG addresses. Skip address checking to allow the access.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Give MPX a real config option. The CPUs that support it (referenced
here):
https://software.intel.com/en-us/forums/topic/402393
are not available publicly yet. Right now only the software emulator
provides MPX for the general public.
[ tglx: Make it default off. There is no point in having it on right
now as no hardware and no proper tooling support are available ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20141212183836.2569D58D@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
problems, clarifies VCPU init, and fixes a regression concerning the
VGIC init flow.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUjsVhAAoJEEtpOizt6ddy5rIH/1V/YVwhprC55YqdHelU9Qu2
Muzsx+7F71NxC7xgMGFqPD1YrPR+hxvoPhy+ADOBlvcqlolrkDnV9I+8e3geaYNc
nZ/yEnoGTtbAggiS1smx7usBv34Z88Sd5txNjmj1cmHBy+VOWlyidWMkGBTsfBRe
mVc61BDUfyC47udgRHXhwS80sbHLJHElmADisFOVmQNBYwwiHiTdx0hMBMnHcC3Y
/3T0tKxHdeTISnmA+J+n7TcChtTIM4xqC6kwf3rw3b7XX8gdtTKylDHX2GLAg646
RdebAG2twmGpIc6SxXZbo38f3oY9OFo1Le5xZGa6iUjD56VDw/e4wg4iA2juo0Y=
=J2Ut
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-3.19-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
Second round of changes for KVM for arm/arm64 for v3.19; fixes reboot
problems, clarifies VCPU init, and fixes a regression concerning the
VGIC init flow.
Conflicts:
arch/ia64/kvm/kvm-ia64.c [deleted in HEAD and modified in kvmarm]
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull x86 fixes from Ingo Molnar:
"Misc fixes (mainly Andy's TLS fixes), plus a cleanup"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tls: Disallow unusual TLS segments
x86/tls: Validate TLS entries to protect espfix
MAINTAINERS: Add me as x86 VDSO submaintainer
x86/asm: Unify segment selector defines
x86/asm: Guard against building the 32/64-bit versions of the asm-offsets*.c file directly
x86_64, switch_to(): Load TLS descriptors before switching DS and ES
x86/mm: Use min() instead of min_t() in the e820 printout code
x86/mm: Fix zone ranges boot printout
x86/doc: Update documentation after file shuffling
Users have no business installing custom code segments into the
GDT, and segments that are not present but are otherwise valid
are a historical source of interesting attacks.
For completeness, block attempts to set the L bit. (Prior to
this patch, the L bit would have been silently dropped.)
This is an ABI break. I've checked glibc, musl, and Wine, and
none of them look like they'll have any trouble.
Note to stable maintainers: this is a hardening patch that fixes
no known bugs. Given the possibility of ABI issues, this
probably shouldn't be backported quickly.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org # optional
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: security@kernel.org <security@kernel.org>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Installing a 16-bit RW data segment into the GDT defeats espfix.
AFAICT this will not affect glibc, Wine, or dosemu at all.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: security@kernel.org <security@kernel.org>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
1) Discovered by Fengguang Wu's tests. I changed the parameters to
the function graph x86 prepare_ftrace_return call but forgot
to update the call from entry_32 (i386 version). This patch corrects
that.
2) I was tracing some code and found that the sched_switch tracepoint
was showing tasks in the INTERRUPTIBLE state as RUNNING. This was
due to the updates to convert preempt_count into a per_cpu variable.
The tracepoint logic was made to use the tasks saved_preempt_count
which could hold a stale "PREEMPT_ACTIVE", instead of using the
current preempt_count() call.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJUi75HAAoJEEjnJuOKh9ldYVoH+LZsoT0m5UVQT8vQmahXABnY
A3l19KGUAL3qaWRf4Au50sK2NdBTfGjvt8KGNkskPsvVv5X3z0GoXIIA76SD/MtX
ysyLUXGCayNCqb3akuzznGZxE8CNKcU5aj3Hy+hIvRI6tgg2sEDt67QBAYsukIOR
MN3us7ezvh0r+8muyPdrpC2OtkwsC1QvX2My1km0UU67CcWxo8zIuzUeeMSe+1+4
6eCjLsVWAznaTo5W9i2DTKpw85hZjfAFgaGn21yRrAHbC+REpaigB9mxZg3Bb1Qb
SovdyGSSEspke4/0Pu7bVXW/lx7dlnEsNWqc0RHWY1nd5FINQY+tRfbmgSoPRA==
=DMsV
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Here's two fixes:
1) Discovered by Fengguang Wu's tests. I changed the parameters to
the function graph x86 prepare_ftrace_return call but forgot to
update the call from entry_32 (i386 version). This patch corrects
that.
2) I was tracing some code and found that the sched_switch tracepoint
was showing tasks in the INTERRUPTIBLE state as RUNNING. This was
due to the updates to convert preempt_count into a per_cpu
variable. The tracepoint logic was made to use the tasks
saved_preempt_count which could hold a stale "PREEMPT_ACTIVE",
instead of using the current preempt_count() call"
* tag 'trace-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/sched: Check preempt_count() for current when reading task->state
ftrace/x86: Update i386 call to prepare_ftrace_return()
Pull crypto update from Herbert Xu:
- The crypto API is now documented :)
- Disallow arbitrary module loading through crypto API.
- Allow get request with empty driver name through crypto_user.
- Allow speed testing of arbitrary hash functions.
- Add caam support for ctr(aes), gcm(aes) and their derivatives.
- nx now supports concurrent hashing properly.
- Add sahara support for SHA1/256.
- Add ARM64 version of CRC32.
- Misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: tcrypt - Allow speed testing of arbitrary hash functions
crypto: af_alg - add user space interface for AEAD
crypto: qat - fix problem with coalescing enable logic
crypto: sahara - add support for SHA1/256
crypto: sahara - replace tasklets with kthread
crypto: sahara - add support for i.MX53
crypto: sahara - fix spinlock initialization
crypto: arm - replace memset by memzero_explicit
crypto: powerpc - replace memset by memzero_explicit
crypto: sha - replace memset by memzero_explicit
crypto: sparc - replace memset by memzero_explicit
crypto: algif_skcipher - initialize upon init request
crypto: algif_skcipher - removed unneeded code
crypto: algif_skcipher - Fixed blocking recvmsg
crypto: drbg - use memzero_explicit() for clearing sensitive data
crypto: drbg - use MODULE_ALIAS_CRYPTO
crypto: include crypto- module prefix in template
crypto: user - add MODULE_ALIAS
crypto: sha-mb - remove a bogus NULL check
crytpo: qat - Fix 64 bytes requests
...
Merge second patchbomb from Andrew Morton:
- the rest of MM
- misc fs fixes
- add execveat() syscall
- new ratelimit feature for fault-injection
- decompressor updates
- ipc/ updates
- fallocate feature creep
- fsnotify cleanups
- a few other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (99 commits)
cgroups: Documentation: fix trivial typos and wrong paragraph numberings
parisc: percpu: update comments referring to __get_cpu_var
percpu: update local_ops.txt to reflect this_cpu operations
percpu: remove __get_cpu_var and __raw_get_cpu_var macros
fsnotify: remove destroy_list from fsnotify_mark
fsnotify: unify inode and mount marks handling
fallocate: create FAN_MODIFY and IN_MODIFY events
mm/cma: make kmemleak ignore CMA regions
slub: fix cpuset check in get_any_partial
slab: fix cpuset check in fallback_alloc
shmdt: use i_size_read() instead of ->i_size
ipc/shm.c: fix overly aggressive shmdt() when calls span multiple segments
ipc/msg: increase MSGMNI, remove scaling
ipc/sem.c: increase SEMMSL, SEMMNI, SEMOPM
ipc/sem.c: change memory barrier in sem_lock() to smp_rmb()
lib/decompress.c: consistency of compress formats for kernel image
decompress_bunzip2: off by one in get_next_block()
usr/Kconfig: make initrd compression algorithm selection not expert
fault-inject: add ratelimit option
ratelimit: add initialization macro
...
Following the suggestions from Andrew Morton and Stephen Rothwell,
Dont expand the ARCH list in kernel/gcov/Kconfig. Instead,
define a ARCH_HAS_GCOV_PROFILE_ALL bool which architectures
can enable.
set ARCH_HAS_GCOV_PROFILE_ALL on Architectures where it was
previously allowed + ARM64 which I tested.
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now, we have prepared to avoid using debug-pagealloc in boottime. So
introduce new kernel-parameter to disable debug-pagealloc in boottime, and
makes related functions to be disabled in this case.
Only non-intuitive part is change of guard page functions. Because guard
page is effective only if debug-pagealloc is enabled, turning off
according to debug-pagealloc is reasonable thing to do.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Jungsoo Son <jungsoo.son@lge.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in x86/kernel/apic/io_apic.c.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull another networking update from David Miller:
"Small follow-up to the main merge pull from the other day:
1) Alexander Duyck's DMA memory barrier patch set.
2) cxgb4 driver fixes from Karen Xie.
3) Add missing export of fixed_phy_register() to modules, from Mark
Salter.
4) DSA bug fixes from Florian Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
net/macb: add TX multiqueue support for gem
linux/interrupt.h: remove the definition of unused tasklet_hi_enable
jme: replace calls to redundant function
net: ethernet: davicom: Allow to select DM9000 for nios2
net: ethernet: smsc: Allow to select SMC91X for nios2
cxgb4: Add support for QSA modules
libcxgbi: fix freeing skb prematurely
cxgb4i: use set_wr_txq() to set tx queues
cxgb4i: handle non-pdu-aligned rx data
cxgb4i: additional types of negative advice
cxgb4/cxgb4i: set the max. pdu length in firmware
cxgb4i: fix credit check for tx_data_wr
cxgb4i: fix tx immediate data credit check
net: phy: export fixed_phy_register()
fib_trie: Fix trie balancing issue if new node pushes down existing node
vlan: Add ability to always enable TSO/UFO
r8169:update rtl8168g pcie ephy parameter
net: dsa: bcm_sf2: force link for all fixed PHY devices
fm10k/igb/ixgbe: Use dma_rmb on Rx descriptor reads
r8169: Use dma_rmb() and dma_wmb() for DescOwn checks
...
The parameters for prepare_ftrace_return() used by the function graph
tracer were swapped to simplify the code on x86_64. But i386 function
graph trampoline also calls this function, and it did not have its
parameters swapped.
Link: http://lkml.kernel.org/r/20141210231732.GA24163@wfg-t540p.sh.intel.com
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 6a06bdbf7f "ftrace/fgraph/x86: Have prepare_ftrace_return() take ip as first parameter"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUiYb+AAoJEFxbo/MsZsTRwmEH+gNaJz5r8gIJlq8Q51+nOIs4
Gw6HdjUB5MOT47vDV4treEOx0Bk8hYTfgWUWvAC81JMJ1sMWOVrUGuG/0lmzaomW
zXvSk+o0n4LafwEhHb8LIccZMbaH7f9o3PNdNchrTkPrIl8Gf2nmBXCkDsT4mRye
5ZFpc4ntgBrznh3baPYDS8PCAmlyZ0uVEnz1ofYI6S80dC13siEiPG0c9TrNEKzO
glhvgCRmR0C4ZNLblM36HWBEqrdLuGCoNJSH+7okygyP2TLD3aO4R+9aD5JWYNdf
fO2WmivX/zK+UGVAElrLx+rb8R2dv3ddeaE5piZhIBUieopIWJd32L3LhQORdtc=
=N6DP
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
* tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (26 commits)
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen/pci: Use APIC directly when APIC virtualization hardware is available
xen/pci: Defer initialization of MSI ops on HVM guests
xen-pciback: drop SR-IOV VFs when PF driver unloads
xen/pciback: Restore configuration space when detaching from a guest.
PCI: Expose pci_load_saved_state for public consumption.
xen/pciback: Remove tons of dereferences
xen/pciback: Print out the domain owning the device.
xen/pciback: Include the domain id if removing the device whilst still in use
driver core: Provide an wrapper around the mutex to do lockdep warnings
xen/pciback: Don't deadlock when unbinding.
swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single
swiotlb-xen: call xen_dma_sync_single_for_device when appropriate
swiotlb-xen: remove BUG_ON in xen_bus_to_phys
swiotlb-xen: pass dev_addr to xen_dma_unmap_page and xen_dma_sync_single_for_cpu
xen/arm: introduce GNTTABOP_cache_flush
xen/arm/arm64: introduce xen_arch_need_swiotlb
xen/arm/arm64: merge xen/mm32.c into xen/mm.c
xen/arm: use hypercall to flush caches in map_page
xen: add a dma_addr_t dev_addr argument to xen_dma_map_page
...
There are a number of situations where the mandatory barriers rmb() and
wmb() are used to order memory/memory operations in the device drivers
and those barriers are much heavier than they actually need to be. For
example in the case of PowerPC wmb() calls the heavy-weight sync
instruction when for coherent memory operations all that is really needed
is an lsync or eieio instruction.
This commit adds a coherent only version of the mandatory memory barriers
rmb() and wmb(). In most cases this should result in the barrier being the
same as the SMP barriers for the SMP case, however in some cases we use a
barrier that is somewhere in between rmb() and smp_rmb(). For example on
ARM the rmb barriers break down as follows:
Barrier Call Explanation
--------- -------- ----------------------------------
rmb() dsb() Data synchronization barrier - system
dma_rmb() dmb(osh) data memory barrier - outer sharable
smp_rmb() dmb(ish) data memory barrier - inner sharable
These new barriers are not as safe as the standard rmb() and wmb().
Specifically they do not guarantee ordering between coherent and incoherent
memories. The primary use case for these would be to enforce ordering of
reads and writes when accessing coherent memory that is shared between the
CPU and a device.
It may also be noted that there is no dma_mb(). Most architectures don't
provide a good mechanism for performing a coherent only full barrier without
resorting to the same mechanism used in mb(). As such there isn't much to
be gained in trying to define such a function.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is meant to cleanup the handling of read_barrier_depends and
smp_read_barrier_depends. In multiple spots in the kernel headers
read_barrier_depends is defined as "do {} while (0)", however we then go
into the SMP vs non-SMP sections and have the SMP version reference
read_barrier_depends, and the non-SMP define it as yet another empty
do/while.
With this commit I went through and cleaned out the duplicate definitions
and reduced the number of definitions down to 2 per header. In addition I
moved the 50 line comments for the macro from the x86 and mips headers that
defined it as an empty do/while to those that were actually defining the
macro, alpha and blackfin.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
* ALSA core
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
* USB-audio
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
* FireWire
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
* HD-audio
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
* ASoC
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
* Others
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sB6v
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
ALSA core:
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
USB-audio:
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
FireWire:
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
HD-audio:
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
ASoC:
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
Others:
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle"
* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: pcxhr: NULL dereference on probe failure
ALSA: lola: NULL dereference on probe failure
ALSA: hda - Add "eapd" model string for AD1986A codec
ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
ALSA: oxfw: Add hwdep interface
ALSA: oxfw: Add support for capture/playback MIDI messages
ALSA: oxfw: add support for capturing PCM samples
ALSA: oxfw: Add support AMDTP in-stream
ALSA: oxfw: Add support for Behringer/Mackie devices
ALSA: oxfw: Change the way to start stream
ALSA: oxfw: Add proc interface for debugging purpose
ALSA: oxfw: Change the way to make PCM rules/constraints
ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
ALSA: oxfw: Change the way to name card
ALSA: dice: Add support for MIDI capture/playback
ALSA: dice: Add support for capturing PCM samples
ALSA: dice: Support for non SYT-Match sampling clock source mode
ALSA: dice: Add support for duplex streams with synchronization
ALSA: dice: Change the way to start stream
ALSA: jack: Add dummy snd_jack_set_key() definition
...
Nadav Amit