Add a new amd_hw_cache_event_ids_f17h assignment structure set
for AMD families 17h and above, since a lot has changed. Specifically:
L1 Data Cache
The data cache access counter remains the same on Family 17h.
For DC misses, PMCx041's definition changes with Family 17h,
so instead we use the L2 cache accesses from L1 data cache
misses counter (PMCx060,umask=0xc8).
For DC hardware prefetch events, Family 17h breaks compatibility
for PMCx067 "Data Prefetcher", so instead, we use PMCx05a "Hardware
Prefetch DC Fills."
L1 Instruction Cache
PMCs 0x80 and 0x81 (32-byte IC fetches and misses) are backward
compatible on Family 17h.
For prefetches, we remove the erroneous PMCx04B assignment which
counts how many software data cache prefetch load instructions were
dispatched.
LL - Last Level Cache
Removing PMCs 7D, 7E, and 7F assignments, as they do not exist
on Family 17h, where the last level cache is L3. L3 counters
can be accessed using the existing AMD Uncore driver.
Data TLB
On Intel machines, data TLB accesses ("dTLB-loads") are assigned
to counters that count load/store instructions retired. This
is inconsistent with instruction TLB accesses, where Intel
implementations report iTLB misses that hit in the STLB.
Ideally, dTLB-loads would count higher level dTLB misses that hit
in lower level TLBs, and dTLB-load-misses would report those
that also missed in those lower-level TLBs, therefore causing
a page table walk. That would be consistent with instruction
TLB operation, remove the redundancy between dTLB-loads and
L1-dcache-loads, and prevent perf from producing artificially
low percentage ratios, i.e. the "0.01%" below:
42,550,869 L1-dcache-loads
41,591,860 dTLB-loads
4,802 dTLB-load-misses # 0.01% of all dTLB cache hits
7,283,682 L1-dcache-stores
7,912,392 dTLB-stores
310 dTLB-store-misses
On AMD Families prior to 17h, the "Data Cache Accesses" counter is
used, which is slightly better than load/store instructions retired,
but still counts in terms of individual load/store operations
instead of TLB operations.
So, for AMD Families 17h and higher, this patch assigns "dTLB-loads"
to a counter for L1 dTLB misses that hit in the L2 dTLB, and
"dTLB-load-misses" to a counter for L1 DTLB misses that caused
L2 DTLB misses and therefore also caused page table walks. This
results in a much more accurate view of data TLB performance:
60,961,781 L1-dcache-loads
4,601 dTLB-loads
963 dTLB-load-misses # 20.93% of all dTLB cache hits
Note that for all AMD families, data loads and stores are combined
in a single accesses counter, so no 'L1-dcache-stores' are reported
separately, and stores are counted with loads in 'L1-dcache-loads'.
Also note that the "% of all dTLB cache hits" string is misleading
because (a) "dTLB cache": although TLBs can be considered caches for
page tables, in this context, it can be misinterpreted as data cache
hits because the figures are similar (at least on Intel), and (b) not
all those loads (technically accesses) technically "hit" at that
hardware level. "% of all dTLB accesses" would be more clear/accurate.
Instruction TLB
On Intel machines, 'iTLB-loads' measure iTLB misses that hit in the
STLB, and 'iTLB-load-misses' measure iTLB misses that also missed in
the STLB and completed a page table walk.
For AMD Family 17h and above, for 'iTLB-loads' we replace the
erroneous instruction cache fetches counter with PMCx084
"L1 ITLB Miss, L2 ITLB Hit".
For 'iTLB-load-misses' we still use PMCx085 "L1 ITLB Miss,
L2 ITLB Miss", but set a 0xff umask because without it the event
does not get counted.
Branch Predictor (BPU)
PMCs 0xc2 and 0xc3 continue to be valid across all AMD Families.
Node Level Events
Family 17h does not have a PMCx0e9 counter, and corresponding counters
have not been made available publicly, so for now, we mark them as
unsupported for Families 17h and above.
Reference:
"Open-Source Register Reference For AMD Family 17h Processors Models 00h-2Fh"
Released 7/17/2018, Publication #56255, Revision 3.03:
https://www.amd.com/system/files/TechDocs/56255_OSRR.pdf
[ mingo: tidied up the line breaks. ]
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Liška <mliska@suse.cz>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Lendacky <Thomas.Lendacky@amd.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Cc: linux-perf-users@vger.kernel.org
Fixes: e40ed1542d ("perf/x86: Add perf support for AMD family-17h processors")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Family 17h differs from prior families by:
- Does not support an L2 cache miss event
- It has re-enumerated PMC counters for:
- L2 cache references
- front & back end stalled cycles
So we add a new amd_f17h_perfmon_event_map[] so that the generic
perf event names will resolve to the correct h/w events on
family 17h and above processors.
Reference sections 2.1.13.3.3 (stalls) and 2.1.13.3.6 (L2):
https://www.amd.com/system/files/TechDocs/54945_PPR_Family_17h_Models_00h-0Fh.pdf
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Liška <mliska@suse.cz>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Fixes: e40ed1542d ("perf/x86: Add perf support for AMD family-17h processors")
[ Improved the formatting a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Spurious interrupt support was added to perf in the following commit, almost
a decade ago:
63e6be6d98 ("perf, x86: Catch spurious interrupts after disabling counters")
The two previous patches (resolving the race condition when disabling a
PMC and NMI latency mitigation) allow for the removal of this older
spurious interrupt support.
Currently in x86_pmu_stop(), the bit for the PMC in the active_mask bitmap
is cleared before disabling the PMC, which sets up a race condition. This
race condition was mitigated by introducing the running bitmap. That race
condition can be eliminated by first disabling the PMC, waiting for PMC
reset on overflow and then clearing the bit for the PMC in the active_mask
bitmap. The NMI handler will not re-enable a disabled counter.
If x86_pmu_stop() is called from the perf NMI handler, the NMI latency
mitigation support will guard against any unhandled NMI messages.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On AMD processors, the detection of an overflowed PMC counter in the NMI
handler relies on the current value of the PMC. So, for example, to check
for overflow on a 48-bit counter, bit 47 is checked to see if it is 1 (not
overflowed) or 0 (overflowed).
When the perf NMI handler executes it does not know in advance which PMC
counters have overflowed. As such, the NMI handler will process all active
PMC counters that have overflowed. NMI latency in newer AMD processors can
result in multiple overflowed PMC counters being processed in one NMI and
then a subsequent NMI, that does not appear to be a back-to-back NMI, not
finding any PMC counters that have overflowed. This may appear to be an
unhandled NMI resulting in either a panic or a series of messages,
depending on how the kernel was configured.
To mitigate this issue, add an AMD handle_irq callback function,
amd_pmu_handle_irq(), that will invoke the common x86_pmu_handle_irq()
function and upon return perform some additional processing that will
indicate if the NMI has been handled or would have been handled had an
earlier NMI not handled the overflowed PMC. Using a per-CPU variable, a
minimum value of the number of active PMCs or 2 will be set whenever a
PMC is active. This is used to indicate the possible number of NMIs that
can still occur. The value of 2 is used for when an NMI does not arrive
at the LAPIC in time to be collapsed into an already pending NMI. Each
time the function is called without having handled an overflowed counter,
the per-CPU value is checked. If the value is non-zero, it is decremented
and the NMI indicates that it handled the NMI. If the value is zero, then
the NMI indicates that it did not handle the NMI.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On AMD processors, the detection of an overflowed counter in the NMI
handler relies on the current value of the counter. So, for example, to
check for overflow on a 48 bit counter, bit 47 is checked to see if it
is 1 (not overflowed) or 0 (overflowed).
There is currently a race condition present when disabling and then
updating the PMC. Increased NMI latency in newer AMD processors makes this
race condition more pronounced. If the counter value has overflowed, it is
possible to update the PMC value before the NMI handler can run. The
updated PMC value is not an overflowed value, so when the perf NMI handler
does run, it will not find an overflowed counter. This may appear as an
unknown NMI resulting in either a panic or a series of messages, depending
on how the kernel is configured.
To eliminate this race condition, the PMC value must be checked after
disabling the counter. Add an AMD function, amd_pmu_disable_all(), that
will wait for the NMI handler to reset any active and overflowed counter
after calling x86_pmu_disable_all().
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For x86 PMUs that do not support context exclusion let's advertise the
PERF_PMU_CAP_NO_EXCLUDE capability. This ensures that perf will
prevent us from handling events where any exclusion flags are set.
Let's also remove the now unnecessary check for exclusion flags.
This change means that amd/iommu and amd/uncore will now also
indicate that they do not support exclude_{hv|idle} and intel/uncore
that it does not support exclude_{guest|host}.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: robin.murphy@arm.com
Cc: suzuki.poulose@arm.com
Link: https://lkml.kernel.org/r/1547128414-50693-12-git-send-email-andrew.murray@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For drivers that do not support context exclusion let's advertise the
PERF_PMU_CAP_NOEXCLUDE capability. This ensures that perf will
prevent us from handling events where any exclusion flags are set.
Let's also remove the now unnecessary check for exclusion flags.
PMU drivers that support at least one exclude flag won't have the
PERF_PMU_CAP_NOEXCLUDE capability set - these PMU drivers should still
check and fail on unsupported exclude flags. These missing tests are
not added in this patch.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: robin.murphy@arm.com
Cc: suzuki.poulose@arm.com
Link: https://lkml.kernel.org/r/1547128414-50693-11-git-send-email-andrew.murray@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 cpu updates from Ingo Molnar:
"The main changes in this cycle were:
- Add support for the "Dhyana" x86 CPUs by Hygon: these are licensed
based on the AMD Zen architecture, and are built and sold in China,
for domestic datacenter use. The code is pretty close to AMD
support, mostly with a few quirks and enumeration differences. (Pu
Wen)
- Enable CPUID support on Cyrix 6x86/6x86L processors"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/cpupower: Add Hygon Dhyana support
cpufreq: Add Hygon Dhyana support
ACPI: Add Hygon Dhyana support
x86/xen: Add Hygon Dhyana support to Xen
x86/kvm: Add Hygon Dhyana support to KVM
x86/mce: Add Hygon Dhyana support to the MCA infrastructure
x86/bugs: Add Hygon Dhyana to the respective mitigation machinery
x86/apic: Add Hygon Dhyana support
x86/pci, x86/amd_nb: Add Hygon Dhyana support to PCI and northbridge
x86/amd_nb: Check vendor in AMD-only functions
x86/alternative: Init ideal_nops for Hygon Dhyana
x86/events: Add Hygon Dhyana support to PMU infrastructure
x86/smpboot: Do not use BSP INIT delay and MWAIT to idle on Dhyana
x86/cpu/mtrr: Support TOP_MEM2 and get MTRR number
x86/cpu: Get cache info and setup cache cpumap for Hygon Dhyana
x86/cpu: Create Hygon Dhyana architecture support file
x86/CPU: Change query logic so CPUID is enabled before testing
x86/CPU: Use correct macros for Cyrix calls
In Family 17h, some L3 Cache Performance events require the ThreadMask
and SliceMask to be set. For other events, these fields do not affect
the count either way.
Set ThreadMask and SliceMask to 0xFF and 0xF respectively.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H . Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 cleanups from Ingo Molnar:
"Misc cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apm: Fix spelling mistake: "caculate" -> "calculate"
x86/mtrr: Rename main.c to mtrr.c and remove duplicate prefixes
x86: Remove pr_fmt duplicate logging prefixes
x86/early-quirks: Rename duplicate define of dev_err
x86/bpf: Clean up non-standard comments, to make the code more readable
Current logic iterates over CPUID Fn8000001d leafs (Cache Properties)
to detect the last level cache, and derive the last-level cache ID.
However, this information is already available in the cpu_llc_id.
Therefore, make use of it instead.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Link: http://lkml.kernel.org/r/1524864877-111962-3-git-send-email-suravee.suthikulpanit@amd.com
The AMD power module can be loaded on non AMD platforms, but unload fails
with the following Oops:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: __list_del_entry_valid+0x29/0x90
Call Trace:
perf_pmu_unregister+0x25/0xf0
amd_power_pmu_exit+0x1c/0xd23 [power]
SyS_delete_module+0x1a8/0x2b0
? exit_to_usermode_loop+0x8f/0xb0
entry_SYSCALL_64_fastpath+0x20/0x83
Return -ENODEV instead of 0 from the module init function if the CPU does
not match.
Fixes: c7ab62bfbe ("perf/x86/amd/power: Add AMD accumulated power reporting mechanism")
Signed-off-by: Xiao Liang <xiliang@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180122061252.6394-1-xiliang@redhat.com
Pull x86 cleanups from Ingo Molnar:
"Two changes: Propagate const/__initconst, and use ARRAY_SIZE() some
more"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/events/amd/iommu: Make iommu_pmu const and __initconst
x86: Use ARRAY_SIZE
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Family 17h, the number of cores sharing a cache level is obtained
from the Cache Properties CPUID leaf (0x8000001d) by passing in the
cache level in ECX. In prior families, a cache level of 2 was used to
determine this information.
To get the right information, irrespective of Family, iterate over
the cache levels using CPUID 0x8000001d. The last level cache is the
last value to return a non-zero value in EAX.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/5ab569025b39cdfaeca55b571d78c0fc800bdb69.1497452002.git.Janakarajan.Natarajan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In Family 17h, L3 is the last level cache as opposed to L2 in previous
families. Avoid this name confusion and rename X86_FEATURE_PERFCTR_L2 to
X86_FEATURE_PERFCTR_LLC to indicate the performance counter on the last
level of cache.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/016311029fdecdc3fdc13b7ed865c6cbf48b2f15.1497452002.git.Janakarajan.Natarajan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fam16h is the same as the default one, remove it. Turn the switch-case
into a simple if-else.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20170410122047.3026-3-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add support for multiple IOMMUs to perf by exposing an AMD IOMMU PMU for
each IOMMU found in the system via:
/bus/event_source/devices/amd_iommu_x
where x is the IOMMU index. This allows users to specify different
events to be programmed into the performance counters of each IOMMU.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
[ Improve readability, shorten names. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1490166162-10002-11-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Current AMD IOMMU perf PMU inappropriately uses the hardware struct
inside the union in struct hw_perf_event, extra_reg in particular.
Instead, introduce an AMD IOMMU-specific struct with required parameters
to be programmed into the IOMMU performance counter control register.
Update the pasid field from 16 to 20 bits while at it.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
[ Fixup macros, shorten get_next_avail_iommu_bnk_cntr() local vars, massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1487926102-13073-10-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, amd_iommu_pc_get_max_[banks|counters]() use end-point device
ID to locate an IOMMU and check the reported max banks/counters. The
logic assumes that the IOMMU_BASE_DEVID belongs to the first IOMMU, and
uses it to acquire a reference to the first IOMMU, which does not work
on certain systems. Instead, modify the function to take an IOMMU index,
and use it to query the corresponding AMD IOMMU instance.
Currently, hardcode the IOMMU index to 0 since the current AMD IOMMU
perf implementation supports only a single IOMMU. A subsequent patch
will add support for multiple IOMMUs, and will use a proper IOMMU index.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1487926102-13073-7-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Introduce amd_iommu_get_num_iommus(), which returns the value of
amd_iommus_present. The function is used to replace direct access to the
variable, which is now declared as static.
This function will also be used by AMD IOMMU perf driver.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1487926102-13073-6-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Clean up register initialization and make use of BIT_ULL(x) where
appropriate. This should not affect logic and functionality.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1487926102-13073-3-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Ingo Molnar:
"Misc fixes and minor updates all over the place:
- an SGI/UV fix
- a defconfig update
- a build warning fix
- move the boot_params file to the arch location in debugfs
- a pkeys fix
- selftests fix
- boot message fixes
- sparse fixes
- a resume warning fix
- ioapic hotplug fixes
- reboot quirks
... plus various minor cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/build/x86_64_defconfig: Enable CONFIG_R8169
x86/reboot/quirks: Add ASUS EeeBook X205TA/W reboot quirk
x86/hpet: Prevent might sleep splat on resume
x86/boot: Correct setup_header.start_sys name
x86/purgatory: Fix sparse warning, symbol not declared
x86/purgatory: Make functions and variables static
x86/events: Remove last remnants of old filenames
x86/pkeys: Check against max pkey to avoid overflows
x86/ioapic: Split IOAPIC hot-removal into two steps
x86/PCI: Implement pcibios_release_device to release IRQ from IOAPIC
x86/intel_rdt: Remove duplicate inclusion of linux/cpu.h
x86/vmware: Remove duplicate inclusion of asm/timer.h
x86/hyperv: Hide unused label
x86/reboot/quirks: Add ASUS EeeBook X205TA reboot quirk
x86/platform/uv/BAU: Fix HUB errors by remove initial write to sw-ack register
x86/selftests: Add clobbers for int80 on x86_64
x86/apic: Simplify enable_IR_x2apic(), remove try_to_enable_IR()
x86/apic: Fix a warning message in logical CPU IDs allocation
x86/kdebugfs: Move boot params hierarchy under (debugfs)/x86/
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Update to the new file paths, remove them from introductory comments.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170218113140.8051-1-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the AMD pieces from the generic Makefile so that
$ make arch/x86/events/amd/<file>.s
can work too. Otherwise you get:
$ make arch/x86/events/amd/ibs.s
scripts/Makefile.build:44: arch/x86/events/amd/Makefile: No such file or directory
make[1]: *** No rule to make target 'arch/x86/events/amd/Makefile'. Stop.
Makefile:1636: recipe for target 'arch/x86/events/amd/ibs.s' failed
make: *** [arch/x86/events/amd/ibs.s] Error 2
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20170126080819.417-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch updates the sysfs attributes for AMD Family17h processors. In
Family17h, the event bit position is changed for both the NorthBridge
and Last level cache counters.
The sysfs attributes are assigned based on the family and the type of
the counter.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/617570ed3634e804991f95db62c3cf3856a9d2a7.1484598705.git.Janakarajan.Natarajan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch updates the AMD uncore driver to support AMD Family17h
processors. In Family17h, there are two extra last level cache counters.
The maximum available counters is increased and the number of counters
for each uncore type is now based on the family.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/799f9c5be8963cc209d9169a08f4a2643b748dc7.1484598705.git.Janakarajan.Natarajan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch renames L2 counters to LLC counters. In AMD Family17h
processors, L3 cache counter is supported.
Since older families have at most L2 counters, last level cache (LLC)
indicates L2/L3 based on the family.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/5d8cd8736d8d578354597a548e64ff16210c319b.1484598705.git.Janakarajan.Natarajan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix a small typo after cleanup state names in cpu/hotplug.
The new convention is 'subsys/xxx/yyy:state' where "state" here is called
"starting" not "STARTING".
Fixes: 73c1b41e63 ("cpu/hotplug: Cleanup state names")
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: http://lkml.kernel.org/r/20161226100511.8662-1-sedat.dilek@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch enables perf core PMU support for the new AMD family-17h processors.
In family-17h, there is no PMC-event constraint. All events, irrespective of
the type, can be measured using any of the six generic performance counters.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1479399306-13375-1-git-send-email-Janakarajan.Natarajan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While the Intel PMU monitors the LLC when perf enables the
HW_CACHE_REFERENCES and HW_CACHE_MISSES events, these events monitor
L1 instruction cache fetches (0x0080) and instruction cache misses
(0x0081) on the AMD PMU.
This is extremely confusing when monitoring the same workload across
Intel and AMD machines, since parameters like,
$ perf stat -e cache-references,cache-misses
measure completely different things.
Instead, make the AMD PMU measure instruction/data cache and TLB fill
requests to the L2 and instruction/data cache and TLB misses in the L2
when HW_CACHE_REFERENCES and HW_CACHE_MISSES are enabled,
respectively. That way the events measure unified caches on both
platforms.
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1472044328-21302-1-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The resent conversion of the cpu hotplug support in the uncore driver
introduced a regression due to the way the callbacks are invoked at
initialization time.
The old code called the prepare/starting/online function on each online cpu
as a block. The new code registers the hotplug callbacks in the core for
each state. The core invokes the callbacks at each registration on all
online cpus.
The code implicitely relied on the prepare/starting/online callbacks being
called as combo on a particular cpu, which was not obvious and completely
undocumented.
The resulting subtle wreckage happens due to the way how the uncore code
manages shared data structures for cpus which share an uncore resource in
hardware. The sharing is determined in the cpu starting callback, but the
prepare callback allocates per cpu data for the upcoming cpu because
potential sharing is unknown at this point. If the starting callback finds
a online cpu which shares the hardware resource it takes a refcount on the
percpu data of that cpu and puts the own data structure into a
'free_at_online' pointer of that shared data structure. The online callback
frees that.
With the old model this worked because in a starting callback only one non
unused structure (the one of the starting cpu) was available. The new code
allocates the data structures for all cpus when the prepare callback is
registered.
Now the starting function iterates through all online cpus and looks for a
data structure (skipping its own) which has a matching hardware id. The id
member of the data structure is initialized to 0, but the hardware id can
be 0 as well. The resulting wreckage is:
CPU0 finds a matching id on CPU1, takes a refcount on CPU1 data and puts
its own data structure into CPU1s data structure to be freed.
CPU1 skips CPU0 because the data structure is its allegedly unsued own.
It finds a matching id on CPU2, takes a refcount on CPU1 data and puts
its own data structure into CPU2s data structure to be freed.
....
Now the online callbacks are invoked.
CPU0 has a pointer to CPU1s data and frees the original CPU0 data. So
far so good.
CPU1 has a pointer to CPU2s data and frees the original CPU1 data, which
is still referenced by CPU0 ---> Booom
So there are two issues to be solved here:
1) The id field must be initialized at allocation time to a value which
cannot be a valid hardware id, i.e. -1
This prevents the above scenario, but now CPU1 and CPU2 both stick their
own data structure into the free_at_online pointer of CPU0. So we leak
CPU1s data structure.
2) Fix the memory leak described in #1
Instead of having a single pointer, use a hlist to enqueue the
superflous data structures which are then freed by the first cpu
invoking the online callback.
Ideally we should know the sharing _before_ invoking the prepare callback,
but that's way beyond the scope of this bug fix.
[ tglx: Rewrote changelog ]
Fixes: 96b2bd3866 ("perf/x86/amd/uncore: Convert to hotplug state machine")
Reported-and-tested-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20160909160822.lowgmkdwms2dheyv@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 header cleanups from Ingo Molnar:
"This tree is a cleanup of the x86 tree reducing spurious uses of
module.h - which should improve build performance a bit"
* 'x86-headers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, crypto: Restore MODULE_LICENSE() to glue_helper.c so it loads
x86/apic: Remove duplicated include from probe_64.c
x86/ce4100: Remove duplicated include from ce4100.c
x86/headers: Include spinlock_types.h in x8664_ksyms_64.c for missing spinlock_t
x86/platform: Delete extraneous MODULE_* tags fromm ts5500
x86: Audit and remove any remaining unnecessary uses of module.h
x86/kvm: Audit and remove any unnecessary uses of module.h
x86/xen: Audit and remove any unnecessary uses of module.h
x86/platform: Audit and remove any unnecessary uses of module.h
x86/lib: Audit and remove any unnecessary uses of module.h
x86/kernel: Audit and remove any unnecessary uses of module.h
x86/mm: Audit and remove any unnecessary uses of module.h
x86: Don't use module.h just for AUTHOR / LICENSE tags
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
This patch adds support for non-linear data on raw records. It
extends raw records to have one or multiple fragments that will
be written linearly into the ring slot, where each fragment can
optionally have a custom callback handler to walk and extract
complex, possibly non-linear data.
If a callback handler is provided for a fragment, then the new
__output_custom() will be used instead of __output_copy() for
the perf_output_sample() part. perf_prepare_sample() does all
the size calculation only once, so perf_output_sample() doesn't
need to redo the same work anymore, meaning real_size and padding
will be cached in the raw record. The raw record becomes 32 bytes
in size without holes; to not increase it further and to avoid
doing unnecessary recalculations in fast-path, we can reuse
next pointer of the last fragment, idea here is borrowed from
ZERO_OR_NULL_PTR(), which should keep the perf_output_sample()
path for PERF_SAMPLE_RAW minimal.
This facility is needed for BPF's event output helper as a first
user that will, in a follow-up, add an additional perf_raw_frag
to its perf_raw_record in order to be able to more efficiently
dump skb context after a linear head meta data related to it.
skbs can be non-linear and thus need a custom output function to
dump buffers. Currently, the skb data needs to be copied twice;
with the help of __output_custom() this work only needs to be
done once. Future users could be things like XDP/BPF programs
that work on different context though and would thus also have
a different callback function.
The few users of raw records are adapted to initialize their frag
data from the raw record itself, no change in behavior for them.
The code is based upon a PoC diff provided by Peter Zijlstra [1].
[1] http://thread.gmane.org/gmane.linux.network/421294
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. In the case of
some of these which are modular, we can extend that to also include
files that are building basic support functionality but not related
to loading or registering the final module; such files also have
no need whatsoever for module.h
The advantage in removing such instances is that module.h itself
sources about 15 other headers; adding significantly to what we feed
cpp, and it can obscure what headers we are effectively using.
Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each instance for the
presence of either and replace as needed.
In the case of crypto/glue_helper.c we delete a redundant instance
of MODULE_LICENSE in order to delete module.h -- the license info
is already present at the top of the file.
The uncore change warrants a mention too; it is uncore.c that uses
module.h and not uncore.h; hence the relocation done there.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160714001901.31603-9-paul.gortmaker@windriver.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kim Phillips