mirror of https://gitee.com/openkylin/linux.git
111 lines
3.2 KiB
Plaintext
111 lines
3.2 KiB
Plaintext
* ARM PrimeCell Color LCD Controller PL110/PL111
|
|
|
|
See also Documentation/devicetree/bindings/arm/primecell.yaml
|
|
|
|
Required properties:
|
|
|
|
- compatible: must be one of:
|
|
"arm,pl110", "arm,primecell"
|
|
"arm,pl111", "arm,primecell"
|
|
|
|
- reg: base address and size of the control registers block
|
|
|
|
- interrupt-names: either the single entry "combined" representing a
|
|
combined interrupt output (CLCDINTR), or the four entries
|
|
"mbe", "vcomp", "lnbu", "fuf" representing the individual
|
|
CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts
|
|
|
|
- interrupts: contains an interrupt specifier for each entry in
|
|
interrupt-names
|
|
|
|
- clock-names: should contain "clcdclk" and "apb_pclk"
|
|
|
|
- clocks: contains phandle and clock specifier pairs for the entries
|
|
in the clock-names property. See
|
|
Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
|
|
Optional properties:
|
|
|
|
- memory-region: phandle to a node describing memory (see
|
|
Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt)
|
|
to be used for the framebuffer; if not present, the framebuffer
|
|
may be located anywhere in the memory
|
|
|
|
- max-memory-bandwidth: maximum bandwidth in bytes per second that the
|
|
cell's memory interface can handle; if not present, the memory
|
|
interface is fast enough to handle all possible video modes
|
|
|
|
Required sub-nodes:
|
|
|
|
- port: describes LCD panel signals, following the common binding
|
|
for video transmitter interfaces; see
|
|
Documentation/devicetree/bindings/media/video-interfaces.txt
|
|
|
|
Deprecated properties:
|
|
The port's endbpoint subnode had this, now deprecated property
|
|
in the past. Drivers should be able to survive without it:
|
|
|
|
- arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values,
|
|
defining the way CLD pads are wired up; first value
|
|
contains index of the "CLD" external pin (pad) used
|
|
as R0 (first bit of the red component), second value
|
|
index of the pad used as G0, third value index of the
|
|
pad used as B0, see also "LCD panel signal multiplexing
|
|
details" paragraphs in the PL110/PL111 Technical
|
|
Reference Manuals; this implicitly defines available
|
|
color modes, for example:
|
|
- PL111 TFT 4:4:4 panel:
|
|
arm,pl11x,tft-r0g0b0-pads = <4 15 20>;
|
|
- PL110 TFT (1:)5:5:5 panel:
|
|
arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
|
|
- PL111 TFT (1:)5:5:5 panel:
|
|
arm,pl11x,tft-r0g0b0-pads = <3 11 19>;
|
|
- PL111 TFT 5:6:5 panel:
|
|
arm,pl11x,tft-r0g0b0-pads = <3 10 19>;
|
|
- PL110 and PL111 TFT 8:8:8 panel:
|
|
arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
|
|
- PL110 and PL111 TFT 8:8:8 panel, R & B components swapped:
|
|
arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
|
|
|
|
|
|
Example:
|
|
|
|
clcd@10020000 {
|
|
compatible = "arm,pl111", "arm,primecell";
|
|
reg = <0x10020000 0x1000>;
|
|
interrupt-names = "combined";
|
|
interrupts = <0 44 4>;
|
|
clocks = <&oscclk1>, <&oscclk2>;
|
|
clock-names = "clcdclk", "apb_pclk";
|
|
max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */
|
|
|
|
port {
|
|
clcd_pads: endpoint {
|
|
remote-endpoint = <&clcd_panel>;
|
|
};
|
|
};
|
|
|
|
};
|
|
|
|
panel {
|
|
compatible = "panel-dpi";
|
|
|
|
port {
|
|
clcd_panel: endpoint {
|
|
remote-endpoint = <&clcd_pads>;
|
|
};
|
|
};
|
|
|
|
panel-timing {
|
|
clock-frequency = <25175000>;
|
|
hactive = <640>;
|
|
hback-porch = <40>;
|
|
hfront-porch = <24>;
|
|
hsync-len = <96>;
|
|
vactive = <480>;
|
|
vback-porch = <32>;
|
|
vfront-porch = <11>;
|
|
vsync-len = <2>;
|
|
};
|
|
};
|