mirror of https://gitee.com/openkylin/linux.git
73 lines
2.3 KiB
Plaintext
73 lines
2.3 KiB
Plaintext
GPIO controllers on MPC8xxx SoCs
|
|
|
|
This is for the non-QE/CPM/GUTs GPIO controllers as found on
|
|
8349, 8572, 8610 and compatible.
|
|
|
|
Every GPIO controller node must have #gpio-cells property defined,
|
|
this information will be used to translate gpio-specifiers.
|
|
See bindings/gpio/gpio.txt for details of how to specify GPIO
|
|
information for devices.
|
|
|
|
The GPIO module usually is connected to the SoC's internal interrupt
|
|
controller, see bindings/interrupt-controller/interrupts.txt (the
|
|
interrupt client nodes section) for details how to specify this GPIO
|
|
module's interrupt.
|
|
|
|
The GPIO module may serve as another interrupt controller (cascaded to
|
|
the SoC's internal interrupt controller). See the interrupt controller
|
|
nodes section in bindings/interrupt-controller/interrupts.txt for
|
|
details.
|
|
|
|
Required properties:
|
|
- compatible: "fsl,<chip>-gpio" followed by "fsl,mpc8349-gpio"
|
|
for 83xx, "fsl,mpc8572-gpio" for 85xx, or
|
|
"fsl,mpc8610-gpio" for 86xx.
|
|
- #gpio-cells: Should be two. The first cell is the pin number
|
|
and the second cell is used to specify optional
|
|
parameters (currently unused).
|
|
- interrupts: Interrupt mapping for GPIO IRQ.
|
|
- gpio-controller: Marks the port as GPIO controller.
|
|
|
|
Optional properties:
|
|
- interrupt-controller: Empty boolean property which marks the GPIO
|
|
module as an IRQ controller.
|
|
- #interrupt-cells: Should be two. Defines the number of integer
|
|
cells required to specify an interrupt within
|
|
this interrupt controller. The first cell
|
|
defines the pin number, the second cell
|
|
defines additional flags (trigger type,
|
|
trigger polarity). Note that the available
|
|
set of trigger conditions supported by the
|
|
GPIO module depends on the actual SoC.
|
|
|
|
Example of gpio-controller nodes for a MPC8347 SoC:
|
|
|
|
gpio1: gpio-controller@c00 {
|
|
#gpio-cells = <2>;
|
|
compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
|
|
reg = <0xc00 0x100>;
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <74 0x8>;
|
|
gpio-controller;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
gpio2: gpio-controller@d00 {
|
|
#gpio-cells = <2>;
|
|
compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
|
|
reg = <0xd00 0x100>;
|
|
interrupt-parent = <&ipic>;
|
|
interrupts = <75 0x8>;
|
|
gpio-controller;
|
|
};
|
|
|
|
Example of a peripheral using the GPIO module as an IRQ controller:
|
|
|
|
funkyfpga@0 {
|
|
compatible = "funky-fpga";
|
|
...
|
|
interrupt-parent = <&gpio1>;
|
|
interrupts = <4 3>;
|
|
};
|