mirror of https://gitee.com/openkylin/linux.git
526 lines
14 KiB
C
526 lines
14 KiB
C
/*
|
|
* pata_artop.c - ARTOP ATA controller driver
|
|
*
|
|
* (C) 2006 Red Hat <alan@redhat.com>
|
|
*
|
|
* Based in part on drivers/ide/pci/aec62xx.c
|
|
* Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
|
|
* 865/865R fixes for Macintosh card version from a patch to the old
|
|
* driver by Thibaut VARENE <varenet@parisc-linux.org>
|
|
* When setting the PCI latency we must set 0x80 or higher for burst
|
|
* performance Alessandro Zummo <alessandro.zummo@towertech.it>
|
|
*
|
|
* TODO
|
|
* 850 serialization once the core supports it
|
|
* Investigate no_dsc on 850R
|
|
* Clock detect
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/init.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/device.h>
|
|
#include <scsi/scsi_host.h>
|
|
#include <linux/libata.h>
|
|
#include <linux/ata.h>
|
|
|
|
#define DRV_NAME "pata_artop"
|
|
#define DRV_VERSION "0.4.3"
|
|
|
|
/*
|
|
* The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
|
|
* get PCI bus speed functionality we leave this as 0. Its a variable
|
|
* for when we get the functionality and also for folks wanting to
|
|
* test stuff.
|
|
*/
|
|
|
|
static int clock = 0;
|
|
|
|
static int artop6210_pre_reset(struct ata_port *ap, unsigned long deadline)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
const struct pci_bits artop_enable_bits[] = {
|
|
{ 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */
|
|
{ 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */
|
|
};
|
|
|
|
if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no]))
|
|
return -ENOENT;
|
|
|
|
return ata_std_prereset(ap, deadline);
|
|
}
|
|
|
|
/**
|
|
* artop6210_error_handler - Probe specified port on PATA host controller
|
|
* @ap: Port to probe
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void artop6210_error_handler(struct ata_port *ap)
|
|
{
|
|
ata_bmdma_drive_eh(ap, artop6210_pre_reset,
|
|
ata_std_softreset, NULL,
|
|
ata_std_postreset);
|
|
}
|
|
|
|
/**
|
|
* artop6260_pre_reset - check for 40/80 pin
|
|
* @ap: Port
|
|
* @deadline: deadline jiffies for the operation
|
|
*
|
|
* The ARTOP hardware reports the cable detect bits in register 0x49.
|
|
* Nothing complicated needed here.
|
|
*/
|
|
|
|
static int artop6260_pre_reset(struct ata_port *ap, unsigned long deadline)
|
|
{
|
|
static const struct pci_bits artop_enable_bits[] = {
|
|
{ 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */
|
|
{ 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */
|
|
};
|
|
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
|
|
/* Odd numbered device ids are the units with enable bits (the -R cards) */
|
|
if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no]))
|
|
return -ENOENT;
|
|
|
|
return ata_std_prereset(ap, deadline);
|
|
}
|
|
|
|
/**
|
|
* artop6260_cable_detect - identify cable type
|
|
* @ap: Port
|
|
*
|
|
* Identify the cable type for the ARTOP interface in question
|
|
*/
|
|
|
|
static int artop6260_cable_detect(struct ata_port *ap)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u8 tmp;
|
|
pci_read_config_byte(pdev, 0x49, &tmp);
|
|
if (tmp & (1 << ap->port_no))
|
|
return ATA_CBL_PATA40;
|
|
return ATA_CBL_PATA80;
|
|
}
|
|
|
|
/**
|
|
* artop6260_error_handler - Probe specified port on PATA host controller
|
|
* @ap: Port to probe
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void artop6260_error_handler(struct ata_port *ap)
|
|
{
|
|
ata_bmdma_drive_eh(ap, artop6260_pre_reset,
|
|
ata_std_softreset, NULL,
|
|
ata_std_postreset);
|
|
}
|
|
|
|
/**
|
|
* artop6210_load_piomode - Load a set of PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device
|
|
* @pio: PIO mode
|
|
*
|
|
* Set PIO mode for device, in host controller PCI config space. This
|
|
* is used both to set PIO timings in PIO mode and also to set the
|
|
* matching PIO clocking for UDMA, as well as the MWDMA timings.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int dn = adev->devno + 2 * ap->port_no;
|
|
const u16 timing[2][5] = {
|
|
{ 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 },
|
|
{ 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 }
|
|
|
|
};
|
|
/* Load the PIO timing active/recovery bits */
|
|
pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]);
|
|
}
|
|
|
|
/**
|
|
* artop6210_set_piomode - Initialize host controller PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device we are configuring
|
|
*
|
|
* Set PIO mode for device, in host controller PCI config space. For
|
|
* ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
|
|
* the event UDMA is used the later call to set_dmamode will set the
|
|
* bits as required.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int dn = adev->devno + 2 * ap->port_no;
|
|
u8 ultra;
|
|
|
|
artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
|
|
|
|
/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
|
|
pci_read_config_byte(pdev, 0x54, &ultra);
|
|
ultra &= ~(3 << (2 * dn));
|
|
pci_write_config_byte(pdev, 0x54, ultra);
|
|
}
|
|
|
|
/**
|
|
* artop6260_load_piomode - Initialize host controller PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device we are configuring
|
|
* @pio: PIO mode
|
|
*
|
|
* Set PIO mode for device, in host controller PCI config space. The
|
|
* ARTOP6260 and relatives store the timing data differently.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int dn = adev->devno + 2 * ap->port_no;
|
|
const u8 timing[2][5] = {
|
|
{ 0x00, 0x0A, 0x08, 0x33, 0x31 },
|
|
{ 0x70, 0x7A, 0x78, 0x43, 0x41 }
|
|
|
|
};
|
|
/* Load the PIO timing active/recovery bits */
|
|
pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]);
|
|
}
|
|
|
|
/**
|
|
* artop6260_set_piomode - Initialize host controller PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device we are configuring
|
|
*
|
|
* Set PIO mode for device, in host controller PCI config space. For
|
|
* ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
|
|
* the event UDMA is used the later call to set_dmamode will set the
|
|
* bits as required.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u8 ultra;
|
|
|
|
artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
|
|
|
|
/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
|
|
pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
|
|
ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */
|
|
pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
|
|
}
|
|
|
|
/**
|
|
* artop6210_set_dmamode - Initialize host controller PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device whose timings we are configuring
|
|
*
|
|
* Set DMA mode for device, in host controller PCI config space.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
unsigned int pio;
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int dn = adev->devno + 2 * ap->port_no;
|
|
u8 ultra;
|
|
|
|
if (adev->dma_mode == XFER_MW_DMA_0)
|
|
pio = 1;
|
|
else
|
|
pio = 4;
|
|
|
|
/* Load the PIO timing active/recovery bits */
|
|
artop6210_load_piomode(ap, adev, pio);
|
|
|
|
pci_read_config_byte(pdev, 0x54, &ultra);
|
|
ultra &= ~(3 << (2 * dn));
|
|
|
|
/* Add ultra DMA bits if in UDMA mode */
|
|
if (adev->dma_mode >= XFER_UDMA_0) {
|
|
u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock;
|
|
if (mode == 0)
|
|
mode = 1;
|
|
ultra |= (mode << (2 * dn));
|
|
}
|
|
pci_write_config_byte(pdev, 0x54, ultra);
|
|
}
|
|
|
|
/**
|
|
* artop6260_set_dmamode - Initialize host controller PATA PIO timings
|
|
* @ap: Port whose timings we are configuring
|
|
* @adev: Device we are configuring
|
|
*
|
|
* Set DMA mode for device, in host controller PCI config space. The
|
|
* ARTOP6260 and relatives store the timing data differently.
|
|
*
|
|
* LOCKING:
|
|
* None (inherited from caller).
|
|
*/
|
|
|
|
static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
unsigned int pio = adev->pio_mode - XFER_PIO_0;
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u8 ultra;
|
|
|
|
if (adev->dma_mode == XFER_MW_DMA_0)
|
|
pio = 1;
|
|
else
|
|
pio = 4;
|
|
|
|
/* Load the PIO timing active/recovery bits */
|
|
artop6260_load_piomode(ap, adev, pio);
|
|
|
|
/* Add ultra DMA bits if in UDMA mode */
|
|
pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
|
|
ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */
|
|
if (adev->dma_mode >= XFER_UDMA_0) {
|
|
u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock;
|
|
if (mode == 0)
|
|
mode = 1;
|
|
ultra |= (mode << (4 * adev->devno));
|
|
}
|
|
pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
|
|
}
|
|
|
|
static struct scsi_host_template artop_sht = {
|
|
.module = THIS_MODULE,
|
|
.name = DRV_NAME,
|
|
.ioctl = ata_scsi_ioctl,
|
|
.queuecommand = ata_scsi_queuecmd,
|
|
.can_queue = ATA_DEF_QUEUE,
|
|
.this_id = ATA_SHT_THIS_ID,
|
|
.sg_tablesize = LIBATA_MAX_PRD,
|
|
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
|
|
.emulated = ATA_SHT_EMULATED,
|
|
.use_clustering = ATA_SHT_USE_CLUSTERING,
|
|
.proc_name = DRV_NAME,
|
|
.dma_boundary = ATA_DMA_BOUNDARY,
|
|
.slave_configure = ata_scsi_slave_config,
|
|
.slave_destroy = ata_scsi_slave_destroy,
|
|
.bios_param = ata_std_bios_param,
|
|
};
|
|
|
|
static const struct ata_port_operations artop6210_ops = {
|
|
.port_disable = ata_port_disable,
|
|
.set_piomode = artop6210_set_piomode,
|
|
.set_dmamode = artop6210_set_dmamode,
|
|
.mode_filter = ata_pci_default_filter,
|
|
|
|
.tf_load = ata_tf_load,
|
|
.tf_read = ata_tf_read,
|
|
.check_status = ata_check_status,
|
|
.exec_command = ata_exec_command,
|
|
.dev_select = ata_std_dev_select,
|
|
|
|
.freeze = ata_bmdma_freeze,
|
|
.thaw = ata_bmdma_thaw,
|
|
.error_handler = artop6210_error_handler,
|
|
.post_internal_cmd = ata_bmdma_post_internal_cmd,
|
|
.cable_detect = ata_cable_40wire,
|
|
|
|
.bmdma_setup = ata_bmdma_setup,
|
|
.bmdma_start = ata_bmdma_start,
|
|
.bmdma_stop = ata_bmdma_stop,
|
|
.bmdma_status = ata_bmdma_status,
|
|
.qc_prep = ata_qc_prep,
|
|
.qc_issue = ata_qc_issue_prot,
|
|
|
|
.data_xfer = ata_data_xfer,
|
|
|
|
.irq_handler = ata_interrupt,
|
|
.irq_clear = ata_bmdma_irq_clear,
|
|
.irq_on = ata_irq_on,
|
|
.irq_ack = ata_irq_ack,
|
|
|
|
.port_start = ata_port_start,
|
|
};
|
|
|
|
static const struct ata_port_operations artop6260_ops = {
|
|
.port_disable = ata_port_disable,
|
|
.set_piomode = artop6260_set_piomode,
|
|
.set_dmamode = artop6260_set_dmamode,
|
|
|
|
.tf_load = ata_tf_load,
|
|
.tf_read = ata_tf_read,
|
|
.check_status = ata_check_status,
|
|
.exec_command = ata_exec_command,
|
|
.dev_select = ata_std_dev_select,
|
|
|
|
.freeze = ata_bmdma_freeze,
|
|
.thaw = ata_bmdma_thaw,
|
|
.error_handler = artop6260_error_handler,
|
|
.post_internal_cmd = ata_bmdma_post_internal_cmd,
|
|
.cable_detect = artop6260_cable_detect,
|
|
|
|
.bmdma_setup = ata_bmdma_setup,
|
|
.bmdma_start = ata_bmdma_start,
|
|
.bmdma_stop = ata_bmdma_stop,
|
|
.bmdma_status = ata_bmdma_status,
|
|
.qc_prep = ata_qc_prep,
|
|
.qc_issue = ata_qc_issue_prot,
|
|
.data_xfer = ata_data_xfer,
|
|
|
|
.irq_handler = ata_interrupt,
|
|
.irq_clear = ata_bmdma_irq_clear,
|
|
.irq_on = ata_irq_on,
|
|
.irq_ack = ata_irq_ack,
|
|
|
|
.port_start = ata_port_start,
|
|
};
|
|
|
|
|
|
/**
|
|
* artop_init_one - Register ARTOP ATA PCI device with kernel services
|
|
* @pdev: PCI device to register
|
|
* @ent: Entry in artop_pci_tbl matching with @pdev
|
|
*
|
|
* Called from kernel PCI layer.
|
|
*
|
|
* LOCKING:
|
|
* Inherited from PCI layer (may sleep).
|
|
*
|
|
* RETURNS:
|
|
* Zero on success, or -ERRNO value.
|
|
*/
|
|
|
|
static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
|
|
{
|
|
static int printed_version;
|
|
static const struct ata_port_info info_6210 = {
|
|
.sht = &artop_sht,
|
|
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
|
|
.pio_mask = 0x1f, /* pio0-4 */
|
|
.mwdma_mask = 0x07, /* mwdma0-2 */
|
|
.udma_mask = ATA_UDMA2,
|
|
.port_ops = &artop6210_ops,
|
|
};
|
|
static const struct ata_port_info info_626x = {
|
|
.sht = &artop_sht,
|
|
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
|
|
.pio_mask = 0x1f, /* pio0-4 */
|
|
.mwdma_mask = 0x07, /* mwdma0-2 */
|
|
.udma_mask = ATA_UDMA4,
|
|
.port_ops = &artop6260_ops,
|
|
};
|
|
static const struct ata_port_info info_626x_fast = {
|
|
.sht = &artop_sht,
|
|
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
|
|
.pio_mask = 0x1f, /* pio0-4 */
|
|
.mwdma_mask = 0x07, /* mwdma0-2 */
|
|
.udma_mask = ATA_UDMA5,
|
|
.port_ops = &artop6260_ops,
|
|
};
|
|
const struct ata_port_info *ppi[] = { NULL, NULL };
|
|
|
|
if (!printed_version++)
|
|
dev_printk(KERN_DEBUG, &pdev->dev,
|
|
"version " DRV_VERSION "\n");
|
|
|
|
if (id->driver_data == 0) { /* 6210 variant */
|
|
ppi[0] = &info_6210;
|
|
ppi[1] = &ata_dummy_port_info;
|
|
/* BIOS may have left us in UDMA, clear it before libata probe */
|
|
pci_write_config_byte(pdev, 0x54, 0);
|
|
/* For the moment (also lacks dsc) */
|
|
printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n");
|
|
printk(KERN_WARNING "Secondary ATA ports will not be activated.\n");
|
|
}
|
|
else if (id->driver_data == 1) /* 6260 */
|
|
ppi[0] = &info_626x;
|
|
else if (id->driver_data == 2) { /* 6260 or 6260 + fast */
|
|
unsigned long io = pci_resource_start(pdev, 4);
|
|
u8 reg;
|
|
|
|
ppi[0] = &info_626x;
|
|
if (inb(io) & 0x10)
|
|
ppi[0] = &info_626x_fast;
|
|
/* Mac systems come up with some registers not set as we
|
|
will need them */
|
|
|
|
/* Clear reset & test bits */
|
|
pci_read_config_byte(pdev, 0x49, ®);
|
|
pci_write_config_byte(pdev, 0x49, reg & ~ 0x30);
|
|
|
|
/* PCI latency must be > 0x80 for burst mode, tweak it
|
|
* if required.
|
|
*/
|
|
pci_read_config_byte(pdev, PCI_LATENCY_TIMER, ®);
|
|
if (reg <= 0x80)
|
|
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90);
|
|
|
|
/* Enable IRQ output and burst mode */
|
|
pci_read_config_byte(pdev, 0x4a, ®);
|
|
pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
|
|
|
|
}
|
|
|
|
BUG_ON(ppi[0] == NULL);
|
|
|
|
return ata_pci_init_one(pdev, ppi);
|
|
}
|
|
|
|
static const struct pci_device_id artop_pci_tbl[] = {
|
|
{ PCI_VDEVICE(ARTOP, 0x0005), 0 },
|
|
{ PCI_VDEVICE(ARTOP, 0x0006), 1 },
|
|
{ PCI_VDEVICE(ARTOP, 0x0007), 1 },
|
|
{ PCI_VDEVICE(ARTOP, 0x0008), 2 },
|
|
{ PCI_VDEVICE(ARTOP, 0x0009), 2 },
|
|
|
|
{ } /* terminate list */
|
|
};
|
|
|
|
static struct pci_driver artop_pci_driver = {
|
|
.name = DRV_NAME,
|
|
.id_table = artop_pci_tbl,
|
|
.probe = artop_init_one,
|
|
.remove = ata_pci_remove_one,
|
|
};
|
|
|
|
static int __init artop_init(void)
|
|
{
|
|
return pci_register_driver(&artop_pci_driver);
|
|
}
|
|
|
|
static void __exit artop_exit(void)
|
|
{
|
|
pci_unregister_driver(&artop_pci_driver);
|
|
}
|
|
|
|
module_init(artop_init);
|
|
module_exit(artop_exit);
|
|
|
|
MODULE_AUTHOR("Alan Cox");
|
|
MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DEVICE_TABLE(pci, artop_pci_tbl);
|
|
MODULE_VERSION(DRV_VERSION);
|
|
|