mirror of https://gitee.com/openkylin/linux.git
91 lines
3.3 KiB
Plaintext
91 lines
3.3 KiB
Plaintext
Broadcom BCM7120-style Level 2 interrupt controller
|
|
|
|
This interrupt controller hardware is a second level interrupt controller that
|
|
is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based
|
|
platforms. It can be found on BCM7xxx products starting with BCM7120.
|
|
|
|
Such an interrupt controller has the following hardware design:
|
|
|
|
- outputs multiple interrupts signals towards its interrupt controller parent
|
|
|
|
- controls how some of the interrupts will be flowing, whether they will
|
|
directly output an interrupt signal towards the interrupt controller parent,
|
|
or if they will output an interrupt signal at this 2nd level interrupt
|
|
controller, in particular for UARTs
|
|
|
|
- has one 32-bit enable word and one 32-bit status word
|
|
|
|
- no atomic set/clear operations
|
|
|
|
- not all bits within the interrupt controller actually map to an interrupt
|
|
|
|
The typical hardware layout for this controller is represented below:
|
|
|
|
2nd level interrupt line Outputs for the parent controller (e.g: ARM GIC)
|
|
|
|
0 -----[ MUX ] ------------|==========> GIC interrupt 75
|
|
\-----------\
|
|
|
|
|
1 -----[ MUX ] --------)---|==========> GIC interrupt 76
|
|
\------------|
|
|
|
|
|
2 -----[ MUX ] --------)---|==========> GIC interrupt 77
|
|
\------------|
|
|
|
|
|
3 ---------------------|
|
|
4 ---------------------|
|
|
5 ---------------------|
|
|
7 ---------------------|---|===========> GIC interrupt 66
|
|
9 ---------------------|
|
|
10 --------------------|
|
|
11 --------------------/
|
|
|
|
6 ------------------------\
|
|
|===========> GIC interrupt 64
|
|
8 ------------------------/
|
|
|
|
12 ........................ X
|
|
13 ........................ X (not connected)
|
|
..
|
|
31 ........................ X
|
|
|
|
Required properties:
|
|
|
|
- compatible: should be "brcm,bcm7120-l2-intc"
|
|
- reg: specifies the base physical address and size of the registers
|
|
- interrupt-controller: identifies the node as an interrupt controller
|
|
- #interrupt-cells: specifies the number of cells needed to encode an interrupt
|
|
source, should be 1.
|
|
- interrupt-parent: specifies the phandle to the parent interrupt controller
|
|
this one is cascaded from
|
|
- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
|
|
node, valid values depend on the type of parent interrupt controller
|
|
- brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts
|
|
are wired to this 2nd level interrupt controller, and how they match their
|
|
respective interrupt parents. Should match exactly the number of interrupts
|
|
specified in the 'interrupts' property.
|
|
|
|
Optional properties:
|
|
|
|
- brcm,irq-can-wake: if present, this means the L2 controller can be used as a
|
|
wakeup source for system suspend/resume.
|
|
|
|
- brcm,int-fwd-mask: if present, a bit mask to configure the interrupts which
|
|
have a mux gate, typically UARTs. Setting these bits will make their
|
|
respective interrupt outputs bypass this 2nd level interrupt controller
|
|
completely; it is completely transparent for the interrupt controller
|
|
parent. This should have one 32-bit word per enable/status pair.
|
|
|
|
Example:
|
|
|
|
irq0_intc: interrupt-controller@f0406800 {
|
|
compatible = "brcm,bcm7120-l2-intc";
|
|
interrupt-parent = <&intc>;
|
|
#interrupt-cells = <1>;
|
|
reg = <0xf0406800 0x8>;
|
|
interrupt-controller;
|
|
interrupts = <0x0 0x42 0x0>, <0x0 0x40 0x0>;
|
|
brcm,int-map-mask = <0xeb8>, <0x140>;
|
|
brcm,int-fwd-mask = <0x7>;
|
|
};
|