mirror of https://gitee.com/openkylin/linux.git
100 lines
3.3 KiB
Plaintext
100 lines
3.3 KiB
Plaintext
General Purpose I2C Bus Mux
|
|
|
|
This binding describes an I2C bus multiplexer that uses a mux controller
|
|
from the mux subsystem to route the I2C signals.
|
|
|
|
.-----. .-----.
|
|
| dev | | dev |
|
|
.------------. '-----' '-----'
|
|
| SoC | | |
|
|
| | .--------+--------'
|
|
| .------. | .------+ child bus A, on MUX value set to 0
|
|
| | I2C |-|--| Mux |
|
|
| '------' | '--+---+ child bus B, on MUX value set to 1
|
|
| .------. | | '----------+--------+--------.
|
|
| | MUX- | | | | | |
|
|
| | Ctrl |-|-----+ .-----. .-----. .-----.
|
|
| '------' | | dev | | dev | | dev |
|
|
'------------' '-----' '-----' '-----'
|
|
|
|
Required properties:
|
|
- compatible: i2c-mux
|
|
- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
|
|
port is connected to.
|
|
- mux-controls: The phandle of the mux controller to use for operating the
|
|
mux.
|
|
* Standard I2C mux properties. See i2c-mux.txt in this directory.
|
|
* I2C child bus nodes. See i2c-mux.txt in this directory. The sub-bus number
|
|
is also the mux-controller state described in ../mux/mux-controller.txt
|
|
|
|
Optional properties:
|
|
- mux-locked: If present, explicitly allow unrelated I2C transactions on the
|
|
parent I2C adapter at these times:
|
|
+ during setup of the multiplexer
|
|
+ between setup of the multiplexer and the child bus I2C transaction
|
|
+ between the child bus I2C transaction and releasing of the multiplexer
|
|
+ during releasing of the multiplexer
|
|
However, I2C transactions to devices behind all I2C multiplexers connected
|
|
to the same parent adapter that this multiplexer is connected to are blocked
|
|
for the full duration of the complete multiplexed I2C transaction (i.e.
|
|
including the times covered by the above list).
|
|
If mux-locked is not present, the multiplexer is assumed to be parent-locked.
|
|
This means that no unrelated I2C transactions are allowed on the parent I2C
|
|
adapter for the complete multiplexed I2C transaction.
|
|
The properties of mux-locked and parent-locked multiplexers are discussed
|
|
in more detail in Documentation/i2c/i2c-topology.
|
|
|
|
For each i2c child node, an I2C child bus will be created. They will
|
|
be numbered based on their order in the device tree.
|
|
|
|
Whenever an access is made to a device on a child bus, the value set
|
|
in the relevant node's reg property will be set as the state in the
|
|
mux controller.
|
|
|
|
Example:
|
|
mux: mux-controller {
|
|
compatible = "gpio-mux";
|
|
#mux-control-cells = <0>;
|
|
|
|
mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
|
|
<&pioA 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
i2c-mux {
|
|
compatible = "i2c-mux";
|
|
mux-locked;
|
|
i2c-parent = <&i2c1>;
|
|
|
|
mux-controls = <&mux>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
i2c@1 {
|
|
reg = <1>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
ssd1307: oled@3c {
|
|
compatible = "solomon,ssd1307fb-i2c";
|
|
reg = <0x3c>;
|
|
pwms = <&pwm 4 3000>;
|
|
reset-gpios = <&gpio2 7 1>;
|
|
reset-active-low;
|
|
};
|
|
};
|
|
|
|
i2c@3 {
|
|
reg = <3>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pca9555: pca9555@20 {
|
|
compatible = "nxp,pca9555";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
reg = <0x20>;
|
|
};
|
|
};
|
|
};
|