mirror of https://gitee.com/openkylin/linux.git
55 lines
2.6 KiB
Plaintext
55 lines
2.6 KiB
Plaintext
Renesas Electronics USBHS driver
|
|
|
|
Required properties:
|
|
- compatible: Must contain one or more of the following:
|
|
|
|
- "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device
|
|
- "renesas,usbhs-r8a7744" for r8a7744 (RZ/G1N) compatible device
|
|
- "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device
|
|
- "renesas,usbhs-r8a774a1" for r8a774a1 (RZ/G2M) compatible device
|
|
- "renesas,usbhs-r8a774c0" for r8a774c0 (RZ/G2E) compatible device
|
|
- "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device
|
|
- "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device
|
|
- "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device
|
|
- "renesas,usbhs-r8a7793" for r8a7793 (R-Car M2-N) compatible device
|
|
- "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device
|
|
- "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device
|
|
- "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device
|
|
- "renesas,usbhs-r8a77965" for r8a77965 (R-Car M3-N) compatible device
|
|
- "renesas,usbhs-r8a77990" for r8a77990 (R-Car E3) compatible device
|
|
- "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device
|
|
- "renesas,usbhs-r7s72100" for r7s72100 (RZ/A1) compatible device
|
|
- "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices
|
|
- "renesas,rcar-gen3-usbhs" for R-Car Gen3 or RZ/G2 compatible devices
|
|
- "renesas,rza1-usbhs" for RZ/A1 compatible device
|
|
|
|
When compatible with the generic version, nodes must list the
|
|
SoC-specific version corresponding to the platform first followed
|
|
by the generic version.
|
|
|
|
- reg: Base address and length of the register for the USBHS
|
|
- interrupts: Interrupt specifier for the USBHS
|
|
- clocks: A list of phandle + clock specifier pairs.
|
|
- In case of "renesas,rcar-gen3-usbhs", two clocks are required.
|
|
First clock should be peripheral and second one should be host.
|
|
- In case of except above, one clock is required. First clock
|
|
should be peripheral.
|
|
|
|
Optional properties:
|
|
- renesas,buswait: Integer to use BUSWAIT register
|
|
- renesas,enable-gpio: A gpio specifier to check GPIO determining if USB
|
|
function should be enabled
|
|
- phys: phandle + phy specifier pair
|
|
- phy-names: must be "usb"
|
|
- dmas: Must contain a list of references to DMA specifiers.
|
|
- dma-names : named "ch%d", where %d is the channel number ranging from zero
|
|
to the number of channels (DnFIFOs) minus one.
|
|
|
|
Example:
|
|
usbhs: usb@e6590000 {
|
|
compatible = "renesas,usbhs-r8a7790", "renesas,rcar-gen2-usbhs";
|
|
reg = <0 0xe6590000 0 0x100>;
|
|
interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
|
|
};
|