mirror of https://gitee.com/openkylin/linux.git
99 lines
3.7 KiB
Plaintext
99 lines
3.7 KiB
Plaintext
* Renesas R-Car GyroADC device driver
|
|
|
|
The GyroADC block is a reduced SPI block with up to 8 chipselect lines,
|
|
which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs
|
|
are sampled by the GyroADC block in a round-robin fashion and the result
|
|
presented in the GyroADC registers.
|
|
|
|
Required properties:
|
|
- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc".
|
|
The <soc-specific> should be one of:
|
|
renesas,r8a7791-gyroadc - for the GyroADC block present
|
|
in r8a7791 SoC
|
|
renesas,r8a7792-gyroadc - for the GyroADC with interrupt
|
|
block present in r8a7792 SoC
|
|
- reg: Address and length of the register set for the device
|
|
- clocks: References to all the clocks specified in the clock-names
|
|
property as specified in
|
|
Documentation/devicetree/bindings/clock/clock-bindings.txt.
|
|
- clock-names: Shall contain "fck". The "fck" is the GyroADC block clock.
|
|
- power-domains: Must contain a reference to the PM domain, if available.
|
|
- #address-cells: Should be <1> (setting for the subnodes) for all ADCs
|
|
except for "fujitsu,mb88101a". Should be <0> (setting for
|
|
only subnode) for "fujitsu,mb88101a".
|
|
- #size-cells: Should be <0> (setting for the subnodes)
|
|
|
|
Sub-nodes:
|
|
You must define subnode(s) which select the connected ADC type and reference
|
|
voltage for the GyroADC channels.
|
|
|
|
Required properties for subnodes:
|
|
- compatible: Should be either of:
|
|
"fujitsu,mb88101a"
|
|
- Fujitsu MB88101A compatible mode,
|
|
12bit sampling, up to 4 channels can be sampled in
|
|
round-robin fashion. One Fujitsu chip supplies four
|
|
GyroADC channels with data as it contains four ADCs
|
|
on the chip and thus for 4-channel operation, single
|
|
MB88101A is required. The Cx chipselect lines of the
|
|
MB88101A connect directly to two CHS lines of the
|
|
GyroADC, no demuxer is required. The data out line
|
|
of each MB88101A connects to a shared input pin of
|
|
the GyroADC.
|
|
"ti,adcs7476" or "ti,adc121" or "adi,ad7476"
|
|
- TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode,
|
|
15bit sampling, up to 8 channels can be sampled in
|
|
round-robin fashion. One TI/ADI chip supplies single
|
|
ADC channel with data, thus for 8-channel operation,
|
|
8 chips are required. A 3:8 chipselect demuxer is
|
|
required to connect the nCS line of the TI/ADI chips
|
|
to the GyroADC, while MISO line of each TI/ADI ADC
|
|
connects to a shared input pin of the GyroADC.
|
|
"maxim,max1162" or "maxim,max11100"
|
|
- Maxim MAX1162 / Maxim MAX11100 compatible mode,
|
|
16bit sampling, up to 8 channels can be sampled in
|
|
round-robin fashion. One Maxim chip supplies single
|
|
ADC channel with data, thus for 8-channel operation,
|
|
8 chips are required. A 3:8 chipselect demuxer is
|
|
required to connect the nCS line of the MAX chips
|
|
to the GyroADC, while MISO line of each Maxim ADC
|
|
connects to a shared input pin of the GyroADC.
|
|
- reg: Should be the number of the analog input. Should be present
|
|
for all ADCs except "fujitsu,mb88101a".
|
|
- vref-supply: Reference to the channel reference voltage regulator.
|
|
|
|
Example:
|
|
vref_max1162: regulator-vref-max1162 {
|
|
compatible = "regulator-fixed";
|
|
|
|
regulator-name = "MAX1162 Vref";
|
|
regulator-min-microvolt = <4096000>;
|
|
regulator-max-microvolt = <4096000>;
|
|
};
|
|
|
|
adc@e6e54000 {
|
|
compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc";
|
|
reg = <0 0xe6e54000 0 64>;
|
|
clocks = <&mstp9_clks R8A7791_CLK_GYROADC>;
|
|
clock-names = "fck";
|
|
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
|
|
|
|
pinctrl-0 = <&adc_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
adc@0 {
|
|
reg = <0>;
|
|
compatible = "maxim,max1162";
|
|
vref-supply = <&vref_max1162>;
|
|
};
|
|
|
|
adc@1 {
|
|
reg = <1>;
|
|
compatible = "maxim,max1162";
|
|
vref-supply = <&vref_max1162>;
|
|
};
|
|
};
|