mirror of https://gitee.com/openkylin/linux.git
178 lines
7.1 KiB
C
178 lines
7.1 KiB
C
/*P:600 The x86 architecture has segments, which involve a table of descriptors
|
|
* which can be used to do funky things with virtual address interpretation.
|
|
* We originally used to use segments so the Guest couldn't alter the
|
|
* Guest<->Host Switcher, and then we had to trim Guest segments, and restore
|
|
* for userspace per-thread segments, but trim again for on userspace->kernel
|
|
* transitions... This nightmarish creation was contained within this file,
|
|
* where we knew not to tread without heavy armament and a change of underwear.
|
|
*
|
|
* In these modern times, the segment handling code consists of simple sanity
|
|
* checks, and the worst you'll experience reading this code is butterfly-rash
|
|
* from frolicking through its parklike serenity. :*/
|
|
#include "lg.h"
|
|
|
|
/*H:600
|
|
* We've almost completed the Host; there's just one file to go!
|
|
*
|
|
* Segments & The Global Descriptor Table
|
|
*
|
|
* (That title sounds like a bad Nerdcore group. Not to suggest that there are
|
|
* any good Nerdcore groups, but in high school a friend of mine had a band
|
|
* called Joe Fish and the Chips, so there are definitely worse band names).
|
|
*
|
|
* To refresh: the GDT is a table of 8-byte values describing segments. Once
|
|
* set up, these segments can be loaded into one of the 6 "segment registers".
|
|
*
|
|
* GDT entries are passed around as "struct desc_struct"s, which like IDT
|
|
* entries are split into two 32-bit members, "a" and "b". One day, someone
|
|
* will clean that up, and be declared a Hero. (No pressure, I'm just saying).
|
|
*
|
|
* Anyway, the GDT entry contains a base (the start address of the segment), a
|
|
* limit (the size of the segment - 1), and some flags. Sounds simple, and it
|
|
* would be, except those zany Intel engineers decided that it was too boring
|
|
* to put the base at one end, the limit at the other, and the flags in
|
|
* between. They decided to shotgun the bits at random throughout the 8 bytes,
|
|
* like so:
|
|
*
|
|
* 0 16 40 48 52 56 63
|
|
* [ limit part 1 ][ base part 1 ][ flags ][li][fl][base ]
|
|
* mit ags part 2
|
|
* part 2
|
|
*
|
|
* As a result, this file contains a certain amount of magic numeracy. Let's
|
|
* begin.
|
|
*/
|
|
|
|
/* There are several entries we don't let the Guest set. The TSS entry is the
|
|
* "Task State Segment" which controls all kinds of delicate things. The
|
|
* LGUEST_CS and LGUEST_DS entries are reserved for the Switcher, and the
|
|
* the Guest can't be trusted to deal with double faults. */
|
|
static int ignored_gdt(unsigned int num)
|
|
{
|
|
return (num == GDT_ENTRY_TSS
|
|
|| num == GDT_ENTRY_LGUEST_CS
|
|
|| num == GDT_ENTRY_LGUEST_DS
|
|
|| num == GDT_ENTRY_DOUBLEFAULT_TSS);
|
|
}
|
|
|
|
/*H:610 Once the GDT has been changed, we fix the new entries up a little. We
|
|
* don't care if they're invalid: the worst that can happen is a General
|
|
* Protection Fault in the Switcher when it restores a Guest segment register
|
|
* which tries to use that entry. Then we kill the Guest for causing such a
|
|
* mess: the message will be "unhandled trap 256". */
|
|
static void fixup_gdt_table(struct lguest *lg, unsigned start, unsigned end)
|
|
{
|
|
unsigned int i;
|
|
|
|
for (i = start; i < end; i++) {
|
|
/* We never copy these ones to real GDT, so we don't care what
|
|
* they say */
|
|
if (ignored_gdt(i))
|
|
continue;
|
|
|
|
/* Segment descriptors contain a privilege level: the Guest is
|
|
* sometimes careless and leaves this as 0, even though it's
|
|
* running at privilege level 1. If so, we fix it here. */
|
|
if ((lg->gdt[i].b & 0x00006000) == 0)
|
|
lg->gdt[i].b |= (GUEST_PL << 13);
|
|
|
|
/* Each descriptor has an "accessed" bit. If we don't set it
|
|
* now, the CPU will try to set it when the Guest first loads
|
|
* that entry into a segment register. But the GDT isn't
|
|
* writable by the Guest, so bad things can happen. */
|
|
lg->gdt[i].b |= 0x00000100;
|
|
}
|
|
}
|
|
|
|
/* This routine is called at boot or modprobe time for each CPU to set up the
|
|
* "constant" GDT entries for Guests running on that CPU. */
|
|
void setup_default_gdt_entries(struct lguest_ro_state *state)
|
|
{
|
|
struct desc_struct *gdt = state->guest_gdt;
|
|
unsigned long tss = (unsigned long)&state->guest_tss;
|
|
|
|
/* The hypervisor segments are full 0-4G segments, privilege level 0 */
|
|
gdt[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT;
|
|
gdt[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT;
|
|
|
|
/* The TSS segment refers to the TSS entry for this CPU, so we cannot
|
|
* copy it from the Guest. Forgive the magic flags */
|
|
gdt[GDT_ENTRY_TSS].a = 0x00000067 | (tss << 16);
|
|
gdt[GDT_ENTRY_TSS].b = 0x00008900 | (tss & 0xFF000000)
|
|
| ((tss >> 16) & 0x000000FF);
|
|
}
|
|
|
|
/* This routine is called before the Guest is run for the first time. */
|
|
void setup_guest_gdt(struct lguest *lg)
|
|
{
|
|
/* Start with full 0-4G segments... */
|
|
lg->gdt[GDT_ENTRY_KERNEL_CS] = FULL_EXEC_SEGMENT;
|
|
lg->gdt[GDT_ENTRY_KERNEL_DS] = FULL_SEGMENT;
|
|
/* ...except the Guest is allowed to use them, so set the privilege
|
|
* level appropriately in the flags. */
|
|
lg->gdt[GDT_ENTRY_KERNEL_CS].b |= (GUEST_PL << 13);
|
|
lg->gdt[GDT_ENTRY_KERNEL_DS].b |= (GUEST_PL << 13);
|
|
}
|
|
|
|
/* Like the IDT, we never simply use the GDT the Guest gives us. We set up the
|
|
* GDTs for each CPU, then we copy across the entries each time we want to run
|
|
* a different Guest on that CPU. */
|
|
|
|
/* A partial GDT load, for the three "thead-local storage" entries. Otherwise
|
|
* it's just like load_guest_gdt(). So much, in fact, it would probably be
|
|
* neater to have a single hypercall to cover both. */
|
|
void copy_gdt_tls(const struct lguest *lg, struct desc_struct *gdt)
|
|
{
|
|
unsigned int i;
|
|
|
|
for (i = GDT_ENTRY_TLS_MIN; i <= GDT_ENTRY_TLS_MAX; i++)
|
|
gdt[i] = lg->gdt[i];
|
|
}
|
|
|
|
/* This is the full version */
|
|
void copy_gdt(const struct lguest *lg, struct desc_struct *gdt)
|
|
{
|
|
unsigned int i;
|
|
|
|
/* The default entries from setup_default_gdt_entries() are not
|
|
* replaced. See ignored_gdt() above. */
|
|
for (i = 0; i < GDT_ENTRIES; i++)
|
|
if (!ignored_gdt(i))
|
|
gdt[i] = lg->gdt[i];
|
|
}
|
|
|
|
/* This is where the Guest asks us to load a new GDT (LHCALL_LOAD_GDT). */
|
|
void load_guest_gdt(struct lguest *lg, unsigned long table, u32 num)
|
|
{
|
|
/* We assume the Guest has the same number of GDT entries as the
|
|
* Host, otherwise we'd have to dynamically allocate the Guest GDT. */
|
|
if (num > ARRAY_SIZE(lg->gdt))
|
|
kill_guest(lg, "too many gdt entries %i", num);
|
|
|
|
/* We read the whole thing in, then fix it up. */
|
|
lgread(lg, lg->gdt, table, num * sizeof(lg->gdt[0]));
|
|
fixup_gdt_table(lg, 0, ARRAY_SIZE(lg->gdt));
|
|
/* Mark that the GDT changed so the core knows it has to copy it again,
|
|
* even if the Guest is run on the same CPU. */
|
|
lg->changed |= CHANGED_GDT;
|
|
}
|
|
|
|
void guest_load_tls(struct lguest *lg, unsigned long gtls)
|
|
{
|
|
struct desc_struct *tls = &lg->gdt[GDT_ENTRY_TLS_MIN];
|
|
|
|
lgread(lg, tls, gtls, sizeof(*tls)*GDT_ENTRY_TLS_ENTRIES);
|
|
fixup_gdt_table(lg, GDT_ENTRY_TLS_MIN, GDT_ENTRY_TLS_MAX+1);
|
|
lg->changed |= CHANGED_GDT_TLS;
|
|
}
|
|
|
|
/*
|
|
* With this, we have finished the Host.
|
|
*
|
|
* Five of the seven parts of our task are complete. You have made it through
|
|
* the Bit of Despair (I think that's somewhere in the page table code,
|
|
* myself).
|
|
*
|
|
* Next, we examine "make Switcher". It's short, but intense.
|
|
*/
|