mirror of https://gitee.com/openkylin/linux.git
114 lines
3.4 KiB
Plaintext
114 lines
3.4 KiB
Plaintext
Kernel driver w83791d
|
|
=====================
|
|
|
|
Supported chips:
|
|
* Winbond W83791D
|
|
Prefix: 'w83791d'
|
|
Addresses scanned: I2C 0x2c - 0x2f
|
|
Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791Da.pdf
|
|
|
|
Author: Charles Spirakis <bezaur@gmail.com>
|
|
|
|
This driver was derived from the w83781d.c and w83792d.c source files.
|
|
|
|
Credits:
|
|
w83781d.c:
|
|
Frodo Looijaard <frodol@dds.nl>,
|
|
Philip Edelbrock <phil@netroedge.com>,
|
|
and Mark Studebaker <mdsxyz123@yahoo.com>
|
|
w83792d.c:
|
|
Chunhao Huang <DZShen@Winbond.com.tw>,
|
|
Rudolf Marek <r.marek@sh.cvut.cz>
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
* init boolean
|
|
(default 0)
|
|
Use 'init=1' to have the driver do extra software initializations.
|
|
The default behavior is to do the minimum initialization possible
|
|
and depend on the BIOS to properly setup the chip. If you know you
|
|
have a w83791d and you're having problems, try init=1 before trying
|
|
reset=1.
|
|
|
|
* reset boolean
|
|
(default 0)
|
|
Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default
|
|
behavior is no chip reset to preserve BIOS settings.
|
|
|
|
* force_subclients=bus,caddr,saddr,saddr
|
|
This is used to force the i2c addresses for subclients of
|
|
a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b'
|
|
to force the subclients of chip 0x2f on bus 0 to i2c addresses
|
|
0x4a and 0x4b.
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
This driver implements support for the Winbond W83791D chip.
|
|
|
|
Detection of the chip can sometimes be foiled because it can be in an
|
|
internal state that allows no clean access (Bank with ID register is not
|
|
currently selected). If you know the address of the chip, use a 'force'
|
|
parameter; this will put it into a more well-behaved state first.
|
|
|
|
The driver implements three temperature sensors, five fan rotation speed
|
|
sensors, and ten voltage sensors.
|
|
|
|
Temperatures are measured in degrees Celsius and measurement resolution is 1
|
|
degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
|
|
the temperature gets higher than the Overtemperature Shutdown value; it stays
|
|
on until the temperature falls below the Hysteresis value.
|
|
|
|
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
|
|
triggered if the rotation speed has dropped below a programmable limit. Fan
|
|
readings can be divided by a programmable divider (1, 2, 4, 8 for fan 1/2/3
|
|
and 1, 2, 4, 8, 16, 32, 64 or 128 for fan 4/5) to give the readings more
|
|
range or accuracy.
|
|
|
|
Voltage sensors (also known as IN sensors) report their values in millivolts.
|
|
An alarm is triggered if the voltage has crossed a programmable minimum
|
|
or maximum limit.
|
|
|
|
Alarms are provided as output from a "realtime status register". The
|
|
following bits are defined:
|
|
|
|
bit - alarm on:
|
|
0 - Vcore
|
|
1 - VINR0
|
|
2 - +3.3VIN
|
|
3 - 5VDD
|
|
4 - temp1
|
|
5 - temp2
|
|
6 - fan1
|
|
7 - fan2
|
|
8 - +12VIN
|
|
9 - -12VIN
|
|
10 - -5VIN
|
|
11 - fan3
|
|
12 - chassis
|
|
13 - temp3
|
|
14 - VINR1
|
|
15 - reserved
|
|
16 - tart1
|
|
17 - tart2
|
|
18 - tart3
|
|
19 - VSB
|
|
20 - VBAT
|
|
21 - fan4
|
|
22 - fan5
|
|
23 - reserved
|
|
|
|
When an alarm goes off, you can be warned by a beeping signal through your
|
|
computer speaker. It is possible to enable all beeping globally, or only
|
|
the beeping for some alarms.
|
|
|
|
The driver only reads the chip values each 3 seconds; reading them more
|
|
often will do no harm, but will return 'old' values.
|
|
|
|
W83791D TODO:
|
|
---------------
|
|
Provide a patch for per-file alarms as discussed on the mailing list
|
|
Provide a patch for smart-fan control (still need appropriate motherboard/fans)
|