mirror of https://gitee.com/openkylin/linux.git
134 lines
4.3 KiB
ReStructuredText
134 lines
4.3 KiB
ReStructuredText
.. -*- coding: utf-8; mode: rst -*-
|
|
|
|
.. _lirc_dev_intro:
|
|
|
|
************
|
|
Introduction
|
|
************
|
|
|
|
LIRC stands for Linux Infrared Remote Control. The LIRC device interface is
|
|
a bi-directional interface for transporting raw IR and decoded scancodes
|
|
data between userspace and kernelspace. Fundamentally, it is just a chardev
|
|
(/dev/lircX, for X = 0, 1, 2, ...), with a number of standard struct
|
|
file_operations defined on it. With respect to transporting raw IR and
|
|
decoded scancodes to and fro, the essential fops are read, write and ioctl.
|
|
|
|
Example dmesg output upon a driver registering w/LIRC:
|
|
|
|
.. code-block:: none
|
|
|
|
$ dmesg |grep lirc_dev
|
|
rc rc0: lirc_dev: driver mceusb registered at minor = 0, raw IR receiver, raw IR transmitter
|
|
|
|
What you should see for a chardev:
|
|
|
|
.. code-block:: none
|
|
|
|
$ ls -l /dev/lirc*
|
|
crw-rw---- 1 root root 248, 0 Jul 2 22:20 /dev/lirc0
|
|
|
|
.. _lirc_modes:
|
|
|
|
**********
|
|
LIRC modes
|
|
**********
|
|
|
|
LIRC supports some modes of receiving and sending IR codes, as shown
|
|
on the following table.
|
|
|
|
.. _lirc-mode-scancode:
|
|
.. _lirc-scancode-flag-toggle:
|
|
.. _lirc-scancode-flag-repeat:
|
|
|
|
``LIRC_MODE_SCANCODE``
|
|
|
|
This mode is for both sending and receiving IR.
|
|
|
|
For transmitting (aka sending), create a ``struct lirc_scancode`` with
|
|
the desired scancode set in the ``scancode`` member, :c:type:`rc_proto`
|
|
set the IR protocol, and all other members set to 0. Write this struct to
|
|
the lirc device.
|
|
|
|
For receiving, you read ``struct lirc_scancode`` from the lirc device,
|
|
with ``scancode`` set to the received scancode and the IR protocol
|
|
:c:type:`rc_proto`. If the scancode maps to a valid key code, this is set
|
|
in the ``keycode`` field, else it is set to ``KEY_RESERVED``.
|
|
|
|
The ``flags`` can have ``LIRC_SCANCODE_FLAG_TOGGLE`` set if the toggle
|
|
bit is set in protocols that support it (e.g. rc-5 and rc-6), or
|
|
``LIRC_SCANCODE_FLAG_REPEAT`` for when a repeat is received for protocols
|
|
that support it (e.g. nec).
|
|
|
|
In the Sanyo and NEC protocol, if you hold a button on remote, rather than
|
|
repeating the entire scancode, the remote sends a shorter message with
|
|
no scancode, which just means button is held, a "repeat". When this is
|
|
received, the ``LIRC_SCANCODE_FLAG_REPEAT`` is set and the scancode and
|
|
keycode is repeated.
|
|
|
|
With nec, there is no way to distinguish "button hold" from "repeatedly
|
|
pressing the same button". The rc-5 and rc-6 protocols have a toggle bit.
|
|
When a button is released and pressed again, the toggle bit is inverted.
|
|
If the toggle bit is set, the ``LIRC_SCANCODE_FLAG_TOGGLE`` is set.
|
|
|
|
The ``timestamp`` field is filled with the time nanoseconds
|
|
(in ``CLOCK_MONOTONIC``) when the scancode was decoded.
|
|
|
|
.. _lirc-mode-mode2:
|
|
|
|
``LIRC_MODE_MODE2``
|
|
|
|
The driver returns a sequence of pulse and space codes to userspace,
|
|
as a series of u32 values.
|
|
|
|
This mode is used only for IR receive.
|
|
|
|
The upper 8 bits determine the packet type, and the lower 24 bits
|
|
the payload. Use ``LIRC_VALUE()`` macro to get the payload, and
|
|
the macro ``LIRC_MODE2()`` will give you the type, which
|
|
is one of:
|
|
|
|
``LIRC_MODE2_PULSE``
|
|
|
|
Signifies the presence of IR in microseconds.
|
|
|
|
``LIRC_MODE2_SPACE``
|
|
|
|
Signifies absence of IR in microseconds.
|
|
|
|
``LIRC_MODE2_FREQUENCY``
|
|
|
|
If measurement of the carrier frequency was enabled with
|
|
:ref:`lirc_set_measure_carrier_mode` then this packet gives you
|
|
the carrier frequency in Hertz.
|
|
|
|
``LIRC_MODE2_TIMEOUT``
|
|
|
|
If timeout reports are enabled with
|
|
:ref:`lirc_set_rec_timeout_reports`, when the timeout set with
|
|
:ref:`lirc_set_rec_timeout` expires due to no IR being detected,
|
|
this packet will be sent, with the number of microseconds with
|
|
no IR.
|
|
|
|
.. _lirc-mode-pulse:
|
|
|
|
``LIRC_MODE_PULSE``
|
|
|
|
In pulse mode, a sequence of pulse/space integer values are written to the
|
|
lirc device using :ref:`lirc-write`.
|
|
|
|
The values are alternating pulse and space lengths, in microseconds. The
|
|
first and last entry must be a pulse, so there must be an odd number
|
|
of entries.
|
|
|
|
This mode is used only for IR send.
|
|
|
|
|
|
**************************
|
|
Remote Controller protocol
|
|
**************************
|
|
|
|
An enum :c:type:`rc_proto` in the :ref:`lirc_header` lists all the
|
|
supported IR protocols:
|
|
|
|
.. kernel-doc:: include/uapi/linux/lirc.h
|