mirror of https://gitee.com/openkylin/linux.git
127 lines
5.0 KiB
Plaintext
127 lines
5.0 KiB
Plaintext
dm-switch
|
||
=========
|
||
|
||
The device-mapper switch target creates a device that supports an
|
||
arbitrary mapping of fixed-size regions of I/O across a fixed set of
|
||
paths. The path used for any specific region can be switched
|
||
dynamically by sending the target a message.
|
||
|
||
It maps I/O to underlying block devices efficiently when there is a large
|
||
number of fixed-sized address regions but there is no simple pattern
|
||
that would allow for a compact representation of the mapping such as
|
||
dm-stripe.
|
||
|
||
Background
|
||
----------
|
||
|
||
Dell EqualLogic and some other iSCSI storage arrays use a distributed
|
||
frameless architecture. In this architecture, the storage group
|
||
consists of a number of distinct storage arrays ("members") each having
|
||
independent controllers, disk storage and network adapters. When a LUN
|
||
is created it is spread across multiple members. The details of the
|
||
spreading are hidden from initiators connected to this storage system.
|
||
The storage group exposes a single target discovery portal, no matter
|
||
how many members are being used. When iSCSI sessions are created, each
|
||
session is connected to an eth port on a single member. Data to a LUN
|
||
can be sent on any iSCSI session, and if the blocks being accessed are
|
||
stored on another member the I/O will be forwarded as required. This
|
||
forwarding is invisible to the initiator. The storage layout is also
|
||
dynamic, and the blocks stored on disk may be moved from member to
|
||
member as needed to balance the load.
|
||
|
||
This architecture simplifies the management and configuration of both
|
||
the storage group and initiators. In a multipathing configuration, it
|
||
is possible to set up multiple iSCSI sessions to use multiple network
|
||
interfaces on both the host and target to take advantage of the
|
||
increased network bandwidth. An initiator could use a simple round
|
||
robin algorithm to send I/O across all paths and let the storage array
|
||
members forward it as necessary, but there is a performance advantage to
|
||
sending data directly to the correct member.
|
||
|
||
A device-mapper table already lets you map different regions of a
|
||
device onto different targets. However in this architecture the LUN is
|
||
spread with an address region size on the order of 10s of MBs, which
|
||
means the resulting table could have more than a million entries and
|
||
consume far too much memory.
|
||
|
||
Using this device-mapper switch target we can now build a two-layer
|
||
device hierarchy:
|
||
|
||
Upper Tier – Determine which array member the I/O should be sent to.
|
||
Lower Tier – Load balance amongst paths to a particular member.
|
||
|
||
The lower tier consists of a single dm multipath device for each member.
|
||
Each of these multipath devices contains the set of paths directly to
|
||
the array member in one priority group, and leverages existing path
|
||
selectors to load balance amongst these paths. We also build a
|
||
non-preferred priority group containing paths to other array members for
|
||
failover reasons.
|
||
|
||
The upper tier consists of a single dm-switch device. This device uses
|
||
a bitmap to look up the location of the I/O and choose the appropriate
|
||
lower tier device to route the I/O. By using a bitmap we are able to
|
||
use 4 bits for each address range in a 16 member group (which is very
|
||
large for us). This is a much denser representation than the dm table
|
||
b-tree can achieve.
|
||
|
||
Construction Parameters
|
||
=======================
|
||
|
||
<num_paths> <region_size> <num_optional_args> [<optional_args>...]
|
||
[<dev_path> <offset>]+
|
||
|
||
<num_paths>
|
||
The number of paths across which to distribute the I/O.
|
||
|
||
<region_size>
|
||
The number of 512-byte sectors in a region. Each region can be redirected
|
||
to any of the available paths.
|
||
|
||
<num_optional_args>
|
||
The number of optional arguments. Currently, no optional arguments
|
||
are supported and so this must be zero.
|
||
|
||
<dev_path>
|
||
The block device that represents a specific path to the device.
|
||
|
||
<offset>
|
||
The offset of the start of data on the specific <dev_path> (in units
|
||
of 512-byte sectors). This number is added to the sector number when
|
||
forwarding the request to the specific path. Typically it is zero.
|
||
|
||
Messages
|
||
========
|
||
|
||
set_region_mappings <index>:<path_nr> [<index>]:<path_nr> [<index>]:<path_nr>...
|
||
|
||
Modify the region table by specifying which regions are redirected to
|
||
which paths.
|
||
|
||
<index>
|
||
The region number (region size was specified in constructor parameters).
|
||
If index is omitted, the next region (previous index + 1) is used.
|
||
Expressed in hexadecimal (WITHOUT any prefix like 0x).
|
||
|
||
<path_nr>
|
||
The path number in the range 0 ... (<num_paths> - 1).
|
||
Expressed in hexadecimal (WITHOUT any prefix like 0x).
|
||
|
||
Status
|
||
======
|
||
|
||
No status line is reported.
|
||
|
||
Example
|
||
=======
|
||
|
||
Assume that you have volumes vg1/switch0 vg1/switch1 vg1/switch2 with
|
||
the same size.
|
||
|
||
Create a switch device with 64kB region size:
|
||
dmsetup create switch --table "0 `blockdev --getsize /dev/vg1/switch0`
|
||
switch 3 128 0 /dev/vg1/switch0 0 /dev/vg1/switch1 0 /dev/vg1/switch2 0"
|
||
|
||
Set mappings for the first 7 entries to point to devices switch0, switch1,
|
||
switch2, switch0, switch1, switch2, switch1:
|
||
dmsetup message switch 0 set_region_mappings 0:0 :1 :2 :0 :1 :2 :1
|