linux/arch/avr32/boards/merisc/setup.c

299 lines
6.7 KiB
C

/*
* Board-specific setup code for the Merisc
*
* Copyright (C) 2008 Martinsson Elektronik AB
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/clk.h>
#include <linux/etherdevice.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/linkage.h>
#include <linux/platform_device.h>
#include <linux/types.h>
#include <linux/leds.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/irq.h>
#include <linux/fb.h>
#include <linux/atmel-mci.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <asm/gpio.h>
#include <mach/at32ap700x.h>
#include <mach/board.h>
#include <mach/init.h>
#include <mach/portmux.h>
#include "merisc.h"
/* Holds the autodetected board model and revision */
static int merisc_board_id;
/* Initialized by bootloader-specific startup code. */
struct tag *bootloader_tags __initdata;
/* Oscillator frequencies. These are board specific */
unsigned long at32_board_osc_rates[3] = {
[0] = 32768, /* 32.768 kHz on RTC osc */
[1] = 20000000, /* 20 MHz on osc0 */
[2] = 12000000, /* 12 MHz on osc1 */
};
struct eth_addr {
u8 addr[6];
};
static struct eth_addr __initdata hw_addr[2];
static struct macb_platform_data __initdata eth_data[2];
static int ads7846_get_pendown_state_PB26(void)
{
return !gpio_get_value(GPIO_PIN_PB(26));
}
static int ads7846_get_pendown_state_PB28(void)
{
return !gpio_get_value(GPIO_PIN_PB(28));
}
static struct ads7846_platform_data __initdata ads7846_data = {
.model = 7846,
.vref_delay_usecs = 100,
.vref_mv = 0,
.keep_vref_on = 0,
.settle_delay_usecs = 150,
.penirq_recheck_delay_usecs = 1,
.x_plate_ohms = 800,
.debounce_rep = 4,
.debounce_max = 10,
.debounce_tol = 50,
.get_pendown_state = ads7846_get_pendown_state_PB26,
.filter_init = NULL,
.filter = NULL,
.filter_cleanup = NULL,
};
static struct spi_board_info __initdata spi0_board_info[] = {
{
.modalias = "ads7846",
.max_speed_hz = 3250000,
.chip_select = 0,
.bus_num = 0,
.platform_data = &ads7846_data,
.mode = SPI_MODE_0,
},
};
static struct mci_platform_data __initdata mci0_data = {
.slot[0] = {
.bus_width = 4,
.detect_pin = GPIO_PIN_PE(19),
.wp_pin = GPIO_PIN_PE(20),
.detect_is_active_high = true,
},
};
static int __init parse_tag_ethernet(struct tag *tag)
{
int i;
i = tag->u.ethernet.mac_index;
if (i < ARRAY_SIZE(hw_addr)) {
memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
sizeof(hw_addr[i].addr));
}
return 0;
}
__tagtable(ATAG_ETHERNET, parse_tag_ethernet);
static void __init set_hw_addr(struct platform_device *pdev)
{
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
const u8 *addr;
void __iomem *regs;
struct clk *pclk;
if (!res)
return;
if (pdev->id >= ARRAY_SIZE(hw_addr))
return;
addr = hw_addr[pdev->id].addr;
if (!is_valid_ether_addr(addr))
return;
regs = (void __iomem __force *)res->start;
pclk = clk_get(&pdev->dev, "pclk");
if (IS_ERR(pclk))
return;
clk_enable(pclk);
__raw_writel((addr[3] << 24) | (addr[2] << 16)
| (addr[1] << 8) | addr[0], regs + 0x98);
__raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
clk_disable(pclk);
clk_put(pclk);
}
static struct i2c_gpio_platform_data i2c_gpio_data = {
.sda_pin = GPIO_PIN_PA(6),
.scl_pin = GPIO_PIN_PA(7),
.sda_is_open_drain = 1,
.scl_is_open_drain = 1,
.udelay = 2,
};
static struct platform_device i2c_gpio_device = {
.name = "i2c-gpio",
.id = 0,
.dev = {
.platform_data = &i2c_gpio_data,
},
};
static struct i2c_board_info __initdata i2c_info[] = {
{
I2C_BOARD_INFO("pcf8563", 0x51)
},
};
#ifdef CONFIG_LEDS_ATMEL_PWM
static struct gpio_led stk_pwm_led[] = {
{
.name = "backlight",
.gpio = 0, /* PWM channel 0 (LCD backlight) */
},
};
static struct gpio_led_platform_data stk_pwm_led_data = {
.num_leds = ARRAY_SIZE(stk_pwm_led),
.leds = stk_pwm_led,
};
static struct platform_device stk_pwm_led_dev = {
.name = "leds-atmel-pwm",
.id = -1,
.dev = {
.platform_data = &stk_pwm_led_data,
},
};
#endif
const char *merisc_model(void)
{
switch (merisc_board_id) {
case 0:
case 1:
return "500-01";
case 2:
return "BT";
default:
return "Unknown";
}
}
const char *merisc_revision(void)
{
switch (merisc_board_id) {
case 0:
return "B";
case 1:
return "D";
case 2:
return "A";
default:
return "Unknown";
}
}
static void detect_merisc_board_id(void)
{
/* Board ID pins MUST be set as input or the board may be damaged */
at32_select_gpio(GPIO_PIN_PA(24), AT32_GPIOF_PULLUP);
at32_select_gpio(GPIO_PIN_PA(25), AT32_GPIOF_PULLUP);
at32_select_gpio(GPIO_PIN_PA(26), AT32_GPIOF_PULLUP);
at32_select_gpio(GPIO_PIN_PA(27), AT32_GPIOF_PULLUP);
merisc_board_id = !gpio_get_value(GPIO_PIN_PA(24)) +
!gpio_get_value(GPIO_PIN_PA(25)) * 2 +
!gpio_get_value(GPIO_PIN_PA(26)) * 4 +
!gpio_get_value(GPIO_PIN_PA(27)) * 8;
}
void __init setup_board(void)
{
at32_map_usart(0, 0, 0);
at32_map_usart(1, 1, 0);
at32_map_usart(3, 3, 0);
at32_setup_serial_console(1);
}
static int __init merisc_init(void)
{
detect_merisc_board_id();
printk(KERN_NOTICE "BOARD: Merisc %s revision %s\n", merisc_model(),
merisc_revision());
/* Reserve pins for SDRAM */
at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL | (1 << 26));
if (merisc_board_id >= 1)
at32_map_usart(2, 2, 0);
at32_add_device_usart(0);
at32_add_device_usart(1);
if (merisc_board_id >= 1)
at32_add_device_usart(2);
at32_add_device_usart(3);
set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
/* ADS7846 PENIRQ */
if (merisc_board_id == 0) {
ads7846_data.get_pendown_state = ads7846_get_pendown_state_PB26;
at32_select_periph(GPIO_PIOB_BASE, 1 << 26,
GPIO_PERIPH_A, AT32_GPIOF_PULLUP);
spi0_board_info[0].irq = AT32_EXTINT(1);
} else {
ads7846_data.get_pendown_state = ads7846_get_pendown_state_PB28;
at32_select_periph(GPIO_PIOB_BASE, 1 << 28, GPIO_PERIPH_A,
AT32_GPIOF_PULLUP);
spi0_board_info[0].irq = AT32_EXTINT(3);
}
/* ADS7846 busy pin */
at32_select_gpio(GPIO_PIN_PA(4), AT32_GPIOF_PULLUP);
at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
at32_add_device_mci(0, &mci0_data);
#ifdef CONFIG_LEDS_ATMEL_PWM
at32_add_device_pwm((1 << 0) | (1 << 2));
platform_device_register(&stk_pwm_led_dev);
#else
at32_add_device_pwm((1 << 2));
#endif
at32_select_gpio(i2c_gpio_data.sda_pin,
AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
at32_select_gpio(i2c_gpio_data.scl_pin,
AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
platform_device_register(&i2c_gpio_device);
i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
return 0;
}
postcore_initcall(merisc_init);