mirror of https://gitee.com/openkylin/linux.git
320 lines
8.4 KiB
C
320 lines
8.4 KiB
C
/*
|
|
* net/dsa/mv88e6131.c - Marvell 88e6095/6095f/6131 switch chip support
|
|
* Copyright (c) 2008-2009 Marvell Semiconductor
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/jiffies.h>
|
|
#include <linux/list.h>
|
|
#include <linux/module.h>
|
|
#include <linux/netdevice.h>
|
|
#include <linux/phy.h>
|
|
#include <net/dsa.h>
|
|
#include "mv88e6xxx.h"
|
|
|
|
static char *mv88e6131_probe(struct device *host_dev, int sw_addr)
|
|
{
|
|
struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
|
|
int ret;
|
|
|
|
if (bus == NULL)
|
|
return NULL;
|
|
|
|
ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), PORT_SWITCH_ID);
|
|
if (ret >= 0) {
|
|
int ret_masked = ret & 0xfff0;
|
|
|
|
if (ret_masked == PORT_SWITCH_ID_6085)
|
|
return "Marvell 88E6085";
|
|
if (ret_masked == PORT_SWITCH_ID_6095)
|
|
return "Marvell 88E6095/88E6095F";
|
|
if (ret == PORT_SWITCH_ID_6131_B2)
|
|
return "Marvell 88E6131 (B2)";
|
|
if (ret_masked == PORT_SWITCH_ID_6131)
|
|
return "Marvell 88E6131";
|
|
}
|
|
|
|
return NULL;
|
|
}
|
|
|
|
static int mv88e6131_setup_global(struct dsa_switch *ds)
|
|
{
|
|
int ret;
|
|
int i;
|
|
|
|
/* Enable the PHY polling unit, don't discard packets with
|
|
* excessive collisions, use a weighted fair queueing scheme
|
|
* to arbitrate between packet queues, set the maximum frame
|
|
* size to 1632, and mask all interrupt sources.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL, 0x04, 0x4400);
|
|
|
|
/* Set the default address aging time to 5 minutes, and
|
|
* enable address learn messages to be sent to all message
|
|
* ports.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
|
|
|
|
/* Configure the priority mapping registers. */
|
|
ret = mv88e6xxx_config_prio(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Set the VLAN ethertype to 0x8100. */
|
|
REG_WRITE(REG_GLOBAL, 0x19, 0x8100);
|
|
|
|
/* Disable ARP mirroring, and configure the upstream port as
|
|
* the port to which ingress and egress monitor frames are to
|
|
* be sent.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1100) | 0x00f0);
|
|
|
|
/* Disable cascade port functionality unless this device
|
|
* is used in a cascade configuration, and set the switch's
|
|
* DSA device number.
|
|
*/
|
|
if (ds->dst->pd->nr_chips > 1)
|
|
REG_WRITE(REG_GLOBAL, 0x1c, 0xf000 | (ds->index & 0x1f));
|
|
else
|
|
REG_WRITE(REG_GLOBAL, 0x1c, 0xe000 | (ds->index & 0x1f));
|
|
|
|
/* Send all frames with destination addresses matching
|
|
* 01:80:c2:00:00:0x to the CPU port.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
|
|
|
|
/* Ignore removed tag data on doubly tagged packets, disable
|
|
* flow control messages, force flow control priority to the
|
|
* highest, and send all special multicast frames to the CPU
|
|
* port at the highest priority.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
|
|
|
|
/* Program the DSA routing table. */
|
|
for (i = 0; i < 32; i++) {
|
|
int nexthop;
|
|
|
|
nexthop = 0x1f;
|
|
if (ds->pd->rtable &&
|
|
i != ds->index && i < ds->dst->pd->nr_chips)
|
|
nexthop = ds->pd->rtable[i] & 0x1f;
|
|
|
|
REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | nexthop);
|
|
}
|
|
|
|
/* Clear all trunk masks. */
|
|
for (i = 0; i < 8; i++)
|
|
REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0x7ff);
|
|
|
|
/* Clear all trunk mappings. */
|
|
for (i = 0; i < 16; i++)
|
|
REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));
|
|
|
|
/* Force the priority of IGMP/MLD snoop frames and ARP frames
|
|
* to the highest setting.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL2, 0x0f, 0x00ff);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6131_setup_port(struct dsa_switch *ds, int p)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int addr = REG_PORT(p);
|
|
u16 val;
|
|
|
|
/* MAC Forcing register: don't force link, speed, duplex
|
|
* or flow control state to any particular values on physical
|
|
* ports, but force the CPU port and all DSA ports to 1000 Mb/s
|
|
* (100 Mb/s on 6085) full duplex.
|
|
*/
|
|
if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
|
|
if (ps->id == PORT_SWITCH_ID_6085)
|
|
REG_WRITE(addr, 0x01, 0x003d); /* 100 Mb/s */
|
|
else
|
|
REG_WRITE(addr, 0x01, 0x003e); /* 1000 Mb/s */
|
|
else
|
|
REG_WRITE(addr, 0x01, 0x0003);
|
|
|
|
/* Port Control: disable Core Tag, disable Drop-on-Lock,
|
|
* transmit frames unmodified, disable Header mode,
|
|
* enable IGMP/MLD snoop, disable DoubleTag, disable VLAN
|
|
* tunneling, determine priority by looking at 802.1p and
|
|
* IP priority fields (IP prio has precedence), and set STP
|
|
* state to Forwarding.
|
|
*
|
|
* If this is the upstream port for this switch, enable
|
|
* forwarding of unknown unicasts, and enable DSA tagging
|
|
* mode.
|
|
*
|
|
* If this is the link to another switch, use DSA tagging
|
|
* mode, but do not enable forwarding of unknown unicasts.
|
|
*/
|
|
val = 0x0433;
|
|
if (p == dsa_upstream_port(ds)) {
|
|
val |= 0x0104;
|
|
/* On 6085, unknown multicast forward is controlled
|
|
* here rather than in Port Control 2 register.
|
|
*/
|
|
if (ps->id == PORT_SWITCH_ID_6085)
|
|
val |= 0x0008;
|
|
}
|
|
if (ds->dsa_port_mask & (1 << p))
|
|
val |= 0x0100;
|
|
REG_WRITE(addr, 0x04, val);
|
|
|
|
/* Port Control 2: don't force a good FCS, don't use
|
|
* VLAN-based, source address-based or destination
|
|
* address-based priority overrides, don't let the switch
|
|
* add or strip 802.1q tags, don't discard tagged or
|
|
* untagged frames on this port, do a destination address
|
|
* lookup on received packets as usual, don't send a copy
|
|
* of all transmitted/received frames on this port to the
|
|
* CPU, and configure the upstream port number.
|
|
*
|
|
* If this is the upstream port for this switch, enable
|
|
* forwarding of unknown multicast addresses.
|
|
*/
|
|
if (ps->id == PORT_SWITCH_ID_6085)
|
|
/* on 6085, bits 3:0 are reserved, bit 6 control ARP
|
|
* mirroring, and multicast forward is handled in
|
|
* Port Control register.
|
|
*/
|
|
REG_WRITE(addr, 0x08, 0x0080);
|
|
else {
|
|
val = 0x0080 | dsa_upstream_port(ds);
|
|
if (p == dsa_upstream_port(ds))
|
|
val |= 0x0040;
|
|
REG_WRITE(addr, 0x08, val);
|
|
}
|
|
|
|
/* Rate Control: disable ingress rate limiting. */
|
|
REG_WRITE(addr, 0x09, 0x0000);
|
|
|
|
/* Rate Control 2: disable egress rate limiting. */
|
|
REG_WRITE(addr, 0x0a, 0x0000);
|
|
|
|
/* Port Association Vector: when learning source addresses
|
|
* of packets, add the address to the address database using
|
|
* a port bitmap that has only the bit for this port set and
|
|
* the other bits clear.
|
|
*/
|
|
REG_WRITE(addr, 0x0b, 1 << p);
|
|
|
|
/* Tag Remap: use an identity 802.1p prio -> switch prio
|
|
* mapping.
|
|
*/
|
|
REG_WRITE(addr, 0x18, 0x3210);
|
|
|
|
/* Tag Remap 2: use an identity 802.1p prio -> switch prio
|
|
* mapping.
|
|
*/
|
|
REG_WRITE(addr, 0x19, 0x7654);
|
|
|
|
return mv88e6xxx_setup_port_common(ds, p);
|
|
}
|
|
|
|
static int mv88e6131_setup(struct dsa_switch *ds)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int i;
|
|
int ret;
|
|
|
|
ret = mv88e6xxx_setup_common(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
mv88e6xxx_ppu_state_init(ds);
|
|
|
|
switch (ps->id) {
|
|
case PORT_SWITCH_ID_6085:
|
|
ps->num_ports = 10;
|
|
break;
|
|
case PORT_SWITCH_ID_6095:
|
|
ps->num_ports = 11;
|
|
break;
|
|
case PORT_SWITCH_ID_6131:
|
|
case PORT_SWITCH_ID_6131_B2:
|
|
ps->num_ports = 8;
|
|
break;
|
|
default:
|
|
return -ENODEV;
|
|
}
|
|
|
|
ret = mv88e6xxx_switch_reset(ds, false);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* @@@ initialise vtu and atu */
|
|
|
|
ret = mv88e6131_setup_global(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
for (i = 0; i < ps->num_ports; i++) {
|
|
ret = mv88e6131_setup_port(ds, i);
|
|
if (ret < 0)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6131_port_to_phy_addr(struct dsa_switch *ds, int port)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
|
|
if (port >= 0 && port < ps->num_ports)
|
|
return port;
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
static int
|
|
mv88e6131_phy_read(struct dsa_switch *ds, int port, int regnum)
|
|
{
|
|
int addr = mv88e6131_port_to_phy_addr(ds, port);
|
|
|
|
if (addr < 0)
|
|
return addr;
|
|
|
|
return mv88e6xxx_phy_read_ppu(ds, addr, regnum);
|
|
}
|
|
|
|
static int
|
|
mv88e6131_phy_write(struct dsa_switch *ds,
|
|
int port, int regnum, u16 val)
|
|
{
|
|
int addr = mv88e6131_port_to_phy_addr(ds, port);
|
|
|
|
if (addr < 0)
|
|
return addr;
|
|
|
|
return mv88e6xxx_phy_write_ppu(ds, addr, regnum, val);
|
|
}
|
|
|
|
struct dsa_switch_driver mv88e6131_switch_driver = {
|
|
.tag_protocol = DSA_TAG_PROTO_DSA,
|
|
.priv_size = sizeof(struct mv88e6xxx_priv_state),
|
|
.probe = mv88e6131_probe,
|
|
.setup = mv88e6131_setup,
|
|
.set_addr = mv88e6xxx_set_addr_direct,
|
|
.phy_read = mv88e6131_phy_read,
|
|
.phy_write = mv88e6131_phy_write,
|
|
.poll_link = mv88e6xxx_poll_link,
|
|
.get_strings = mv88e6xxx_get_strings,
|
|
.get_ethtool_stats = mv88e6xxx_get_ethtool_stats,
|
|
.get_sset_count = mv88e6xxx_get_sset_count,
|
|
};
|
|
|
|
MODULE_ALIAS("platform:mv88e6085");
|
|
MODULE_ALIAS("platform:mv88e6095");
|
|
MODULE_ALIAS("platform:mv88e6095f");
|
|
MODULE_ALIAS("platform:mv88e6131");
|