mirror of https://gitee.com/openkylin/linux.git
555 lines
12 KiB
C
555 lines
12 KiB
C
/*
|
|
* net/dsa/mv88e6352.c - Marvell 88e6352 switch chip support
|
|
*
|
|
* Copyright (c) 2014 Guenter Roeck
|
|
*
|
|
* Derived from mv88e6123_61_65.c
|
|
* Copyright (c) 2008-2009 Marvell Semiconductor
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/jiffies.h>
|
|
#include <linux/list.h>
|
|
#include <linux/module.h>
|
|
#include <linux/netdevice.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/phy.h>
|
|
#include <net/dsa.h>
|
|
#include "mv88e6xxx.h"
|
|
|
|
static char *mv88e6352_probe(struct device *host_dev, int sw_addr)
|
|
{
|
|
struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
|
|
int ret;
|
|
|
|
if (bus == NULL)
|
|
return NULL;
|
|
|
|
ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), PORT_SWITCH_ID);
|
|
if (ret >= 0) {
|
|
if ((ret & 0xfff0) == PORT_SWITCH_ID_6176)
|
|
return "Marvell 88E6176";
|
|
if (ret == PORT_SWITCH_ID_6352_A0)
|
|
return "Marvell 88E6352 (A0)";
|
|
if (ret == PORT_SWITCH_ID_6352_A1)
|
|
return "Marvell 88E6352 (A1)";
|
|
if ((ret & 0xfff0) == PORT_SWITCH_ID_6352)
|
|
return "Marvell 88E6352";
|
|
}
|
|
|
|
return NULL;
|
|
}
|
|
|
|
static int mv88e6352_setup_global(struct dsa_switch *ds)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int ret;
|
|
int i;
|
|
|
|
/* Discard packets with excessive collisions,
|
|
* mask all interrupt sources, enable PPU (bit 14, undocumented).
|
|
*/
|
|
REG_WRITE(REG_GLOBAL, 0x04, 0x6000);
|
|
|
|
/* Set the default address aging time to 5 minutes, and
|
|
* enable address learn messages to be sent to all message
|
|
* ports.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
|
|
|
|
/* Configure the priority mapping registers. */
|
|
ret = mv88e6xxx_config_prio(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Configure the upstream port, and configure the upstream
|
|
* port as the port to which ingress and egress monitor frames
|
|
* are to be sent.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1110));
|
|
|
|
/* Disable remote management for now, and set the switch's
|
|
* DSA device number.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL, 0x1c, ds->index & 0x1f);
|
|
|
|
/* Send all frames with destination addresses matching
|
|
* 01:80:c2:00:00:2x to the CPU port.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL2, 0x02, 0xffff);
|
|
|
|
/* Send all frames with destination addresses matching
|
|
* 01:80:c2:00:00:0x to the CPU port.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
|
|
|
|
/* Disable the loopback filter, disable flow control
|
|
* messages, disable flood broadcast override, disable
|
|
* removing of provider tags, disable ATU age violation
|
|
* interrupts, disable tag flow control, force flow
|
|
* control priority to the highest, and send all special
|
|
* multicast frames to the CPU at the highest priority.
|
|
*/
|
|
REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
|
|
|
|
/* Program the DSA routing table. */
|
|
for (i = 0; i < 32; i++) {
|
|
int nexthop = 0x1f;
|
|
|
|
if (i != ds->index && i < ds->dst->pd->nr_chips)
|
|
nexthop = ds->pd->rtable[i] & 0x1f;
|
|
|
|
REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | nexthop);
|
|
}
|
|
|
|
/* Clear all trunk masks. */
|
|
for (i = 0; i < 8; i++)
|
|
REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0x7f);
|
|
|
|
/* Clear all trunk mappings. */
|
|
for (i = 0; i < 16; i++)
|
|
REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));
|
|
|
|
/* Disable ingress rate limiting by resetting all ingress
|
|
* rate limit registers to their initial state.
|
|
*/
|
|
for (i = 0; i < ps->num_ports; i++)
|
|
REG_WRITE(REG_GLOBAL2, 0x09, 0x9000 | (i << 8));
|
|
|
|
/* Initialise cross-chip port VLAN table to reset defaults. */
|
|
REG_WRITE(REG_GLOBAL2, 0x0b, 0x9000);
|
|
|
|
/* Clear the priority override table. */
|
|
for (i = 0; i < 16; i++)
|
|
REG_WRITE(REG_GLOBAL2, 0x0f, 0x8000 | (i << 8));
|
|
|
|
/* @@@ initialise AVB (22/23) watchdog (27) sdet (29) registers */
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6352_setup_port(struct dsa_switch *ds, int p)
|
|
{
|
|
int addr = REG_PORT(p);
|
|
u16 val;
|
|
|
|
/* MAC Forcing register: don't force link, speed, duplex
|
|
* or flow control state to any particular values on physical
|
|
* ports, but force the CPU port and all DSA ports to 1000 Mb/s
|
|
* full duplex.
|
|
*/
|
|
if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
|
|
REG_WRITE(addr, 0x01, 0x003e);
|
|
else
|
|
REG_WRITE(addr, 0x01, 0x0003);
|
|
|
|
/* Do not limit the period of time that this port can be
|
|
* paused for by the remote end or the period of time that
|
|
* this port can pause the remote end.
|
|
*/
|
|
REG_WRITE(addr, 0x02, 0x0000);
|
|
|
|
/* Port Control: disable Drop-on-Unlock, disable Drop-on-Lock,
|
|
* disable Header mode, enable IGMP/MLD snooping, disable VLAN
|
|
* tunneling, determine priority by looking at 802.1p and IP
|
|
* priority fields (IP prio has precedence), and set STP state
|
|
* to Forwarding.
|
|
*
|
|
* If this is the CPU link, use DSA or EDSA tagging depending
|
|
* on which tagging mode was configured.
|
|
*
|
|
* If this is a link to another switch, use DSA tagging mode.
|
|
*
|
|
* If this is the upstream port for this switch, enable
|
|
* forwarding of unknown unicasts and multicasts.
|
|
*/
|
|
val = 0x0433;
|
|
if (dsa_is_cpu_port(ds, p)) {
|
|
if (ds->dst->tag_protocol == DSA_TAG_PROTO_EDSA)
|
|
val |= 0x3300;
|
|
else
|
|
val |= 0x0100;
|
|
}
|
|
if (ds->dsa_port_mask & (1 << p))
|
|
val |= 0x0100;
|
|
if (p == dsa_upstream_port(ds))
|
|
val |= 0x000c;
|
|
REG_WRITE(addr, 0x04, val);
|
|
|
|
/* Port Control 2: don't force a good FCS, set the maximum
|
|
* frame size to 10240 bytes, don't let the switch add or
|
|
* strip 802.1q tags, don't discard tagged or untagged frames
|
|
* on this port, do a destination address lookup on all
|
|
* received packets as usual, disable ARP mirroring and don't
|
|
* send a copy of all transmitted/received frames on this port
|
|
* to the CPU.
|
|
*/
|
|
REG_WRITE(addr, 0x08, 0x2080);
|
|
|
|
/* Egress rate control: disable egress rate control. */
|
|
REG_WRITE(addr, 0x09, 0x0001);
|
|
|
|
/* Egress rate control 2: disable egress rate control. */
|
|
REG_WRITE(addr, 0x0a, 0x0000);
|
|
|
|
/* Port Association Vector: when learning source addresses
|
|
* of packets, add the address to the address database using
|
|
* a port bitmap that has only the bit for this port set and
|
|
* the other bits clear.
|
|
*/
|
|
REG_WRITE(addr, 0x0b, 1 << p);
|
|
|
|
/* Port ATU control: disable limiting the number of address
|
|
* database entries that this port is allowed to use.
|
|
*/
|
|
REG_WRITE(addr, 0x0c, 0x0000);
|
|
|
|
/* Priority Override: disable DA, SA and VTU priority override. */
|
|
REG_WRITE(addr, 0x0d, 0x0000);
|
|
|
|
/* Port Ethertype: use the Ethertype DSA Ethertype value. */
|
|
REG_WRITE(addr, 0x0f, ETH_P_EDSA);
|
|
|
|
/* Tag Remap: use an identity 802.1p prio -> switch prio
|
|
* mapping.
|
|
*/
|
|
REG_WRITE(addr, 0x18, 0x3210);
|
|
|
|
/* Tag Remap 2: use an identity 802.1p prio -> switch prio
|
|
* mapping.
|
|
*/
|
|
REG_WRITE(addr, 0x19, 0x7654);
|
|
|
|
return mv88e6xxx_setup_port_common(ds, p);
|
|
}
|
|
|
|
#ifdef CONFIG_NET_DSA_HWMON
|
|
|
|
static int mv88e6352_get_temp(struct dsa_switch *ds, int *temp)
|
|
{
|
|
int ret;
|
|
|
|
*temp = 0;
|
|
|
|
ret = mv88e6xxx_phy_page_read(ds, 0, 6, 27);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
*temp = (ret & 0xff) - 25;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6352_get_temp_limit(struct dsa_switch *ds, int *temp)
|
|
{
|
|
int ret;
|
|
|
|
*temp = 0;
|
|
|
|
ret = mv88e6xxx_phy_page_read(ds, 0, 6, 26);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
*temp = (((ret >> 8) & 0x1f) * 5) - 25;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6352_set_temp_limit(struct dsa_switch *ds, int temp)
|
|
{
|
|
int ret;
|
|
|
|
ret = mv88e6xxx_phy_page_read(ds, 0, 6, 26);
|
|
if (ret < 0)
|
|
return ret;
|
|
temp = clamp_val(DIV_ROUND_CLOSEST(temp, 5) + 5, 0, 0x1f);
|
|
return mv88e6xxx_phy_page_write(ds, 0, 6, 26,
|
|
(ret & 0xe0ff) | (temp << 8));
|
|
}
|
|
|
|
static int mv88e6352_get_temp_alarm(struct dsa_switch *ds, bool *alarm)
|
|
{
|
|
int ret;
|
|
|
|
*alarm = false;
|
|
|
|
ret = mv88e6xxx_phy_page_read(ds, 0, 6, 26);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
*alarm = !!(ret & 0x40);
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_NET_DSA_HWMON */
|
|
|
|
static int mv88e6352_setup(struct dsa_switch *ds)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int ret;
|
|
int i;
|
|
|
|
ret = mv88e6xxx_setup_common(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ps->num_ports = 7;
|
|
|
|
mutex_init(&ps->eeprom_mutex);
|
|
|
|
ret = mv88e6xxx_switch_reset(ds, true);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* @@@ initialise vtu and atu */
|
|
|
|
ret = mv88e6352_setup_global(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
for (i = 0; i < ps->num_ports; i++) {
|
|
ret = mv88e6352_setup_port(ds, i);
|
|
if (ret < 0)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6352_read_eeprom_word(struct dsa_switch *ds, int addr)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int ret;
|
|
|
|
mutex_lock(&ps->eeprom_mutex);
|
|
|
|
ret = mv88e6xxx_reg_write(ds, REG_GLOBAL2, 0x14,
|
|
0xc000 | (addr & 0xff));
|
|
if (ret < 0)
|
|
goto error;
|
|
|
|
ret = mv88e6xxx_eeprom_busy_wait(ds);
|
|
if (ret < 0)
|
|
goto error;
|
|
|
|
ret = mv88e6xxx_reg_read(ds, REG_GLOBAL2, 0x15);
|
|
error:
|
|
mutex_unlock(&ps->eeprom_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int mv88e6352_get_eeprom(struct dsa_switch *ds,
|
|
struct ethtool_eeprom *eeprom, u8 *data)
|
|
{
|
|
int offset;
|
|
int len;
|
|
int ret;
|
|
|
|
offset = eeprom->offset;
|
|
len = eeprom->len;
|
|
eeprom->len = 0;
|
|
|
|
eeprom->magic = 0xc3ec4951;
|
|
|
|
ret = mv88e6xxx_eeprom_load_wait(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (offset & 1) {
|
|
int word;
|
|
|
|
word = mv88e6352_read_eeprom_word(ds, offset >> 1);
|
|
if (word < 0)
|
|
return word;
|
|
|
|
*data++ = (word >> 8) & 0xff;
|
|
|
|
offset++;
|
|
len--;
|
|
eeprom->len++;
|
|
}
|
|
|
|
while (len >= 2) {
|
|
int word;
|
|
|
|
word = mv88e6352_read_eeprom_word(ds, offset >> 1);
|
|
if (word < 0)
|
|
return word;
|
|
|
|
*data++ = word & 0xff;
|
|
*data++ = (word >> 8) & 0xff;
|
|
|
|
offset += 2;
|
|
len -= 2;
|
|
eeprom->len += 2;
|
|
}
|
|
|
|
if (len) {
|
|
int word;
|
|
|
|
word = mv88e6352_read_eeprom_word(ds, offset >> 1);
|
|
if (word < 0)
|
|
return word;
|
|
|
|
*data++ = word & 0xff;
|
|
|
|
offset++;
|
|
len--;
|
|
eeprom->len++;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6352_eeprom_is_readonly(struct dsa_switch *ds)
|
|
{
|
|
int ret;
|
|
|
|
ret = mv88e6xxx_reg_read(ds, REG_GLOBAL2, 0x14);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (!(ret & 0x0400))
|
|
return -EROFS;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6352_write_eeprom_word(struct dsa_switch *ds, int addr,
|
|
u16 data)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int ret;
|
|
|
|
mutex_lock(&ps->eeprom_mutex);
|
|
|
|
ret = mv88e6xxx_reg_write(ds, REG_GLOBAL2, 0x15, data);
|
|
if (ret < 0)
|
|
goto error;
|
|
|
|
ret = mv88e6xxx_reg_write(ds, REG_GLOBAL2, 0x14,
|
|
0xb000 | (addr & 0xff));
|
|
if (ret < 0)
|
|
goto error;
|
|
|
|
ret = mv88e6xxx_eeprom_busy_wait(ds);
|
|
error:
|
|
mutex_unlock(&ps->eeprom_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int mv88e6352_set_eeprom(struct dsa_switch *ds,
|
|
struct ethtool_eeprom *eeprom, u8 *data)
|
|
{
|
|
int offset;
|
|
int ret;
|
|
int len;
|
|
|
|
if (eeprom->magic != 0xc3ec4951)
|
|
return -EINVAL;
|
|
|
|
ret = mv88e6352_eeprom_is_readonly(ds);
|
|
if (ret)
|
|
return ret;
|
|
|
|
offset = eeprom->offset;
|
|
len = eeprom->len;
|
|
eeprom->len = 0;
|
|
|
|
ret = mv88e6xxx_eeprom_load_wait(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (offset & 1) {
|
|
int word;
|
|
|
|
word = mv88e6352_read_eeprom_word(ds, offset >> 1);
|
|
if (word < 0)
|
|
return word;
|
|
|
|
word = (*data++ << 8) | (word & 0xff);
|
|
|
|
ret = mv88e6352_write_eeprom_word(ds, offset >> 1, word);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
offset++;
|
|
len--;
|
|
eeprom->len++;
|
|
}
|
|
|
|
while (len >= 2) {
|
|
int word;
|
|
|
|
word = *data++;
|
|
word |= *data++ << 8;
|
|
|
|
ret = mv88e6352_write_eeprom_word(ds, offset >> 1, word);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
offset += 2;
|
|
len -= 2;
|
|
eeprom->len += 2;
|
|
}
|
|
|
|
if (len) {
|
|
int word;
|
|
|
|
word = mv88e6352_read_eeprom_word(ds, offset >> 1);
|
|
if (word < 0)
|
|
return word;
|
|
|
|
word = (word & 0xff00) | *data++;
|
|
|
|
ret = mv88e6352_write_eeprom_word(ds, offset >> 1, word);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
offset++;
|
|
len--;
|
|
eeprom->len++;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
struct dsa_switch_driver mv88e6352_switch_driver = {
|
|
.tag_protocol = DSA_TAG_PROTO_EDSA,
|
|
.priv_size = sizeof(struct mv88e6xxx_priv_state),
|
|
.probe = mv88e6352_probe,
|
|
.setup = mv88e6352_setup,
|
|
.set_addr = mv88e6xxx_set_addr_indirect,
|
|
.phy_read = mv88e6xxx_phy_read_indirect,
|
|
.phy_write = mv88e6xxx_phy_write_indirect,
|
|
.poll_link = mv88e6xxx_poll_link,
|
|
.get_strings = mv88e6xxx_get_strings,
|
|
.get_ethtool_stats = mv88e6xxx_get_ethtool_stats,
|
|
.get_sset_count = mv88e6xxx_get_sset_count,
|
|
.set_eee = mv88e6xxx_set_eee,
|
|
.get_eee = mv88e6xxx_get_eee,
|
|
#ifdef CONFIG_NET_DSA_HWMON
|
|
.get_temp = mv88e6352_get_temp,
|
|
.get_temp_limit = mv88e6352_get_temp_limit,
|
|
.set_temp_limit = mv88e6352_set_temp_limit,
|
|
.get_temp_alarm = mv88e6352_get_temp_alarm,
|
|
#endif
|
|
.get_eeprom = mv88e6352_get_eeprom,
|
|
.set_eeprom = mv88e6352_set_eeprom,
|
|
.get_regs_len = mv88e6xxx_get_regs_len,
|
|
.get_regs = mv88e6xxx_get_regs,
|
|
.port_join_bridge = mv88e6xxx_join_bridge,
|
|
.port_leave_bridge = mv88e6xxx_leave_bridge,
|
|
.port_stp_update = mv88e6xxx_port_stp_update,
|
|
.fdb_add = mv88e6xxx_port_fdb_add,
|
|
.fdb_del = mv88e6xxx_port_fdb_del,
|
|
.fdb_getnext = mv88e6xxx_port_fdb_getnext,
|
|
};
|
|
|
|
MODULE_ALIAS("platform:mv88e6352");
|