openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity
linux/arch/arm/boot/dts/omap5-cm-t54.dts

414 lines
10 KiB
Plaintext
Raw Blame History

/*
* Support for CompuLab CM-T54
*/
/dts-v1/;
#include "omap5.dtsi"
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
model = "CompuLab CM-T54";
compatible = "compulab,omap5-cm-t54", "ti,omap5";
memory {
device_type = "memory";
reg = <0x80000000 0x7F000000>; /* 2048 MB */
};
vmmcsd_fixed: fixed-regulator-mmcsd {
compatible = "regulator-fixed";
regulator-name = "vmmcsd_fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vwlan_pdn_fixed: fixed-regulator-vwlan-pdn {
compatible = "regulator-fixed";
regulator-name = "vwlan_pdn_fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&ldo2_reg>;
gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* gpio4_109 */
startup-delay-us = <1000>;
enable-active-high;
};
vwlan_fixed: fixed-regulator-vwlan {
compatible = "regulator-fixed";
regulator-name = "vwlan_fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vwlan_pdn_fixed>;
gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* gpio4_110 */
startup-delay-us = <1000>;
enable-active-high;
};
/* HS USB Host PHY on PORT 2 */
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
};
/* HS USB Host PHY on PORT 3 */
hsusb3_phy: hsusb3_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
};
leds {
compatible = "gpio-leds";
led@1 {
label = "Heartbeat";
gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
linux,default-trigger = "heartbeat";
default-state = "off";
};
};
};
&omap5_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&led_gpio_pins
&usbhost_pins
>;
led_gpio_pins: pinmux_led_gpio_pins {
pinctrl-single,pins = <
OMAP5_CORE_IOPAD(0x28b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
>;
};
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
OMAP5_CORE_IOPAD(0x29f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
OMAP5_CORE_IOPAD(0x29f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
>;
};
mmc1_pins: pinmux_mmc1_pins {
pinctrl-single,pins = <
OMAP5_CORE_IOPAD(0x29e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
OMAP5_CORE_IOPAD(0x29e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
OMAP5_CORE_IOPAD(0x29e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
OMAP5_CORE_IOPAD(0x29e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
OMAP5_CORE_IOPAD(0x29ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
OMAP5_CORE_IOPAD(0x29ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
>;
};
mmc2_pins: pinmux_mmc2_pins {
pinctrl-single,pins = <
OMAP5_CORE_IOPAD(0x2840, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
OMAP5_CORE_IOPAD(0x2842, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
OMAP5_CORE_IOPAD(0x2844, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
OMAP5_CORE_IOPAD(0x2846, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
OMAP5_CORE_IOPAD(0x2848, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
OMAP5_CORE_IOPAD(0x284a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
OMAP5_CORE_IOPAD(0x284c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
OMAP5_CORE_IOPAD(0x284e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
OMAP5_CORE_IOPAD(0x2850, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
OMAP5_CORE_IOPAD(0x2852, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
>;
};
mmc3_pins: pinmux_mmc3_pins {
pinctrl-single,pins = <
OMAP5_CORE_IOPAD(0x29a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
OMAP5_CORE_IOPAD(0x29a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
OMAP5_CORE_IOPAD(0x29a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
OMAP5_CORE_IOPAD(0x29aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
OMAP5_CORE_IOPAD(0x29ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
OMAP5_CORE_IOPAD(0x29ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
>;
};
wlan_gpios_pins: pinmux_wlan_gpios_pins {
pinctrl-single,pins = <
OMAP5_CORE_IOPAD(0x299c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_109 */
OMAP5_CORE_IOPAD(0x299e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_110 */
>;
};
usbhost_pins: pinmux_usbhost_pins {
pinctrl-single,pins = <
OMAP5_CORE_IOPAD(0x28c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
OMAP5_CORE_IOPAD(0x28c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
OMAP5_CORE_IOPAD(0x29dc, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
OMAP5_CORE_IOPAD(0x29de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
OMAP5_CORE_IOPAD(0x28a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
OMAP5_CORE_IOPAD(0x28b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
>;
};
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <&ldo9_reg>;
bus-width = <4>;
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&vmmcsd_fixed>;
bus-width = <8>;
ti,non-removable;
};
&mmc3 {
pinctrl-names = "default";
pinctrl-0 = <
&mmc3_pins
&wlan_gpios_pins
>;
vmmc-supply = <&vwlan_fixed>;
bus-width = <4>;
ti,non-removable;
};
&mmc4 {
status = "disabled";
};
&mmc5 {
status = "disabled";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
at24@50 {
compatible = "at24,24c02";
pagesize = <16>;
reg = <0x50>;
};
palmas: palmas@48 {
compatible = "ti,palmas";
interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
interrupt-parent = <&gic>;
reg = <0x48>;
interrupt-controller;
#interrupt-cells = <2>;
ti,system-power-controller;
extcon_usb3: palmas_usb {
compatible = "ti,palmas-usb-vid";
ti,enable-vbus-detection;
ti,enable-id-detection;
ti,wakeup;
};
rtc {
compatible = "ti,palmas-rtc";
interrupt-parent = <&palmas>;
interrupts = <8 IRQ_TYPE_NONE>;
};
palmas_pmic {
compatible = "ti,palmas-pmic";
interrupt-parent = <&palmas>;
interrupts = <14 IRQ_TYPE_NONE>;
interrupt-name = "short-irq";
ti,ldo6-vibrator;
regulators {
smps123_reg: smps123 {
/* VDD_OPP_MPU */
regulator-name = "smps123";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
};
smps45_reg: smps45 {
/* VDD_OPP_MM */
regulator-name = "smps45";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1310000>;
regulator-always-on;
regulator-boot-on;
};
smps6_reg: smps6 {
/* VDD_DDR3 - over VDD_SMPS6 */
regulator-name = "smps6";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
};
smps7_reg: smps7 {
/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
regulator-name = "smps7";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
smps8_reg: smps8 {
/* VDD_OPP_CORE */
regulator-name = "smps8";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1310000>;
regulator-always-on;
regulator-boot-on;
};
smps9_reg: smps9 {
/* VDDA_2v1_AUD over VDD_2v1 */
regulator-name = "smps9";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
ti,smps-range = <0x80>;
regulator-always-on;
regulator-boot-on;
};
smps10_out2_reg: smps10_out2 {
/* VBUS_5V_OTG */
regulator-name = "smps10_out2";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
smps10_out1_reg: smps10_out1 {
/* VBUS_5V_OTG */
regulator-name = "smps10_out1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
ldo1_reg: ldo1 {
/* VDDAPHY_CAM: vdda_csiport */
regulator-name = "ldo1";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1800000>;
};
ldo2_reg: ldo2 {
/* VDD_3V3_WLAN */
regulator-name = "ldo2";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <1000>;
};
ldo3_reg: ldo3 {
/* VCC_1V5_AUD */
regulator-name = "ldo3";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
};
ldo4_reg: ldo4 {
/* VDDAPHY_DISP: vdda_dsiport/hdmi */
regulator-name = "ldo4";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1800000>;
};
ldo5_reg: ldo5 {
/* VDDA_1V8_PHY: usb/sata/hdmi.. */
regulator-name = "ldo5";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldo6_reg: ldo6 {
/* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
regulator-name = "ldo6";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
};
ldo7_reg: ldo7 {
/* VDD_VPP: vpp1 */
regulator-name = "ldo7";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
/* Only for efuse reprograming! */
status = "disabled";
};
ldo8_reg: ldo8 {
/* VDD_3v0: Does not go anywhere */
regulator-name = "ldo8";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-boot-on;
/* Unused */
status = "disabled";
};
ldo9_reg: ldo9 {
/* VCC_DV_SDIO: vdds_sdcard */
regulator-name = "ldo9";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3000000>;
regulator-boot-on;
};
ldoln_reg: ldoln {
/* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
regulator-name = "ldoln";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldousb_reg: ldousb {
/* VDDA_3V_USB: VDDA_USBHS33 */
regulator-name = "ldousb";
regulator-min-microvolt = <3250000>;
regulator-max-microvolt = <3250000>;
regulator-always-on;
regulator-boot-on;
};
regen3_reg: regen3 {
/* REGEN3 controls LDO9 supply to card */
regulator-name = "regen3";
regulator-always-on;
regulator-boot-on;
};
};
};
};
};
&usbhshost {
port2-mode = "ehci-hsic";
port3-mode = "ehci-hsic";
};
&usbhsehci {
phys = <0 &hsusb2_phy &hsusb3_phy>;
};
&cpu0 {
cpu0-supply = <&smps123_reg>;
};
Reference in New Issue View Git Blame Copy Permalink