mirror of https://gitee.com/openkylin/linux.git
117 lines
3.4 KiB
ArmAsm
117 lines
3.4 KiB
ArmAsm
/*
|
|
* DRAM/SDRAM initialization - alter with care
|
|
* This file is intended to be included from other assembler files
|
|
*
|
|
* Note: This file may not modify r8 or r9 because they are used to
|
|
* carry information from the decompresser to the kernel
|
|
*
|
|
* Copyright (C) 2000-2007 Axis Communications AB
|
|
*
|
|
* Authors: Mikael Starvik <starvik@axis.com>
|
|
*/
|
|
|
|
/* Just to be certain the config file is included, we include it here
|
|
* explicitly instead of depending on it being included in the file that
|
|
* uses this code.
|
|
*/
|
|
|
|
#include <hwregs/asm/reg_map_asm.h>
|
|
#include <hwregs/asm/bif_core_defs_asm.h>
|
|
|
|
;; WARNING! The registers r8 and r9 are used as parameters carrying
|
|
;; information from the decompressor (if the kernel was compressed).
|
|
;; They should not be used in the code below.
|
|
|
|
; Refer to BIF MDS for a description of SDRAM initialization
|
|
|
|
; Bank configuration
|
|
move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_cfg_grp0), $r0
|
|
move.d CONFIG_ETRAX_SDRAM_GRP0_CONFIG, $r1
|
|
move.d $r1, [$r0]
|
|
move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_cfg_grp1), $r0
|
|
move.d CONFIG_ETRAX_SDRAM_GRP1_CONFIG, $r1
|
|
move.d $r1, [$r0]
|
|
|
|
; Calculate value of mrs_data
|
|
; CAS latency = 2 && bus_width = 32 => 0x40
|
|
; CAS latency = 3 && bus_width = 32 => 0x60
|
|
; CAS latency = 2 && bus_width = 16 => 0x20
|
|
; CAS latency = 3 && bus_width = 16 => 0x30
|
|
|
|
; Check if value is already supplied in kernel config
|
|
move.d CONFIG_ETRAX_SDRAM_COMMAND, $r2
|
|
bne _set_timing
|
|
nop
|
|
|
|
move.d 0x40, $r4 ; Assume 32 bits and CAS latency = 2
|
|
move.d CONFIG_ETRAX_SDRAM_TIMING, $r1
|
|
and.d 0x07, $r1 ; Get CAS latency
|
|
cmpq 2, $r1 ; CL = 2 ?
|
|
beq _bw_check
|
|
nop
|
|
move.d 0x60, $r4
|
|
|
|
_bw_check:
|
|
; Assume that group 0 width is equal to group 1. This assumption
|
|
; is wrong for a group 1 only hardware (such as the grand old
|
|
; StorPoint+).
|
|
move.d CONFIG_ETRAX_SDRAM_GRP0_CONFIG, $r1
|
|
and.d 0x200, $r1 ; DRAM width is bit 9
|
|
beq _set_timing
|
|
lslq 2, $r4 ; mrs_data starts at bit 2
|
|
lsrq 1, $r4 ; 16 bits. Shift down value.
|
|
|
|
; Set timing parameters (refresh off to avoid Guinness TR 83)
|
|
_set_timing:
|
|
move.d CONFIG_ETRAX_SDRAM_TIMING, $r1
|
|
and.d ~(3 << reg_bif_core_rw_sdram_timing___ref___lsb), $r1
|
|
move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_timing), $r0
|
|
move.d $r1, [$r0]
|
|
|
|
; Issue NOP command
|
|
move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_cmd), $r5
|
|
moveq regk_bif_core_nop, $r1
|
|
move.d $r1, [$r5]
|
|
|
|
; Wait 200us
|
|
move.d 10000, $r2
|
|
1: bne 1b
|
|
subq 1, $r2
|
|
|
|
; Issue initialization command sequence
|
|
lapc _sdram_commands_start, $r2
|
|
lapc _sdram_commands_end, $r3
|
|
1: clear.d $r6
|
|
move.b [$r2+], $r6 ; Load command
|
|
or.d $r4, $r6 ; Add calculated mrs
|
|
move.d $r6, [$r5] ; Write rw_sdram_cmd
|
|
; Wait 80 ns between each command
|
|
move.d 4000, $r7
|
|
2: bne 2b
|
|
subq 1, $r7
|
|
cmp.d $r2, $r3 ; Last command?
|
|
bne 1b
|
|
nop
|
|
|
|
; Start refresh
|
|
move.d CONFIG_ETRAX_SDRAM_TIMING, $r1
|
|
move.d REG_ADDR(bif_core, regi_bif_core, rw_sdram_timing), $r0
|
|
move.d $r1, [$r0]
|
|
|
|
; Initialization finished
|
|
ba _sdram_commands_end
|
|
nop
|
|
|
|
_sdram_commands_start:
|
|
.byte regk_bif_core_pre ; Precharge
|
|
.byte regk_bif_core_ref ; refresh
|
|
.byte regk_bif_core_ref ; refresh
|
|
.byte regk_bif_core_ref ; refresh
|
|
.byte regk_bif_core_ref ; refresh
|
|
.byte regk_bif_core_ref ; refresh
|
|
.byte regk_bif_core_ref ; refresh
|
|
.byte regk_bif_core_ref ; refresh
|
|
.byte regk_bif_core_ref ; refresh
|
|
.byte regk_bif_core_mrs ; mrs
|
|
_sdram_commands_end:
|