mirror of https://gitee.com/openkylin/linux.git
76 lines
2.2 KiB
Plaintext
76 lines
2.2 KiB
Plaintext
* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
|
|
|
|
The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
|
|
HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
|
|
input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
|
|
similar to the 7611 but has 2 HDMI inputs.
|
|
|
|
These device tree bindings support the ADV7611/12 only at the moment.
|
|
|
|
Required Properties:
|
|
|
|
- compatible: Must contain one of the following
|
|
- "adi,adv7611" for the ADV7611
|
|
- "adi,adv7612" for the ADV7612
|
|
|
|
- reg: I2C slave address
|
|
|
|
- hpd-gpios: References to the GPIOs that control the HDMI hot-plug
|
|
detection pins, one per HDMI input. The active flag indicates the GPIO
|
|
level that enables hot-plug detection.
|
|
|
|
The device node must contain one 'port' child node per device input and output
|
|
port, in accordance with the video interface bindings defined in
|
|
Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
|
|
are numbered as follows.
|
|
|
|
Port ADV7611 ADV7612
|
|
------------------------------------------------------------
|
|
HDMI 0 0, 1
|
|
Digital output 1 2
|
|
|
|
The digital output port node must contain at least one endpoint.
|
|
|
|
Optional Properties:
|
|
|
|
- reset-gpios: Reference to the GPIO connected to the device's reset pin.
|
|
|
|
Optional Endpoint Properties:
|
|
|
|
The following three properties are defined in video-interfaces.txt and are
|
|
valid for source endpoints only.
|
|
|
|
- hsync-active: Horizontal synchronization polarity. Defaults to active low.
|
|
- vsync-active: Vertical synchronization polarity. Defaults to active low.
|
|
- pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
|
|
|
|
If none of hsync-active, vsync-active and pclk-sample is specified the
|
|
endpoint will use embedded BT.656 synchronization.
|
|
|
|
- default-input: Select which input is selected after reset.
|
|
|
|
Example:
|
|
|
|
hdmi_receiver@4c {
|
|
compatible = "adi,adv7611";
|
|
reg = <0x4c>;
|
|
|
|
reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
|
|
hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
default-input = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
};
|
|
port@1 {
|
|
reg = <1>;
|
|
hdmi_in: endpoint {
|
|
remote-endpoint = <&ccdc_in>;
|
|
};
|
|
};
|
|
};
|