mirror of https://gitee.com/openkylin/linux.git
82 lines
2.7 KiB
Plaintext
82 lines
2.7 KiB
Plaintext
* MSM Serial UARTDM
|
|
|
|
The MSM serial UARTDM hardware is designed for high-speed use cases where the
|
|
transmit and/or receive channels can be offloaded to a dma-engine. From a
|
|
software perspective it's mostly compatible with the MSM serial UART except
|
|
that it supports reading and writing multiple characters at a time.
|
|
|
|
Required properties:
|
|
- compatible: Should contain at least "qcom,msm-uartdm".
|
|
A more specific property should be specified as follows depending
|
|
on the version:
|
|
"qcom,msm-uartdm-v1.1"
|
|
"qcom,msm-uartdm-v1.2"
|
|
"qcom,msm-uartdm-v1.3"
|
|
"qcom,msm-uartdm-v1.4"
|
|
- reg: Should contain UART register locations and lengths. The first
|
|
register shall specify the main control registers. An optional second
|
|
register location shall specify the GSBI control region.
|
|
"qcom,msm-uartdm-v1.3" is the only compatible value that might
|
|
need the GSBI control region.
|
|
- interrupts: Should contain UART interrupt.
|
|
- clocks: Should contain the core clock and the AHB clock.
|
|
- clock-names: Should be "core" for the core clock and "iface" for the
|
|
AHB clock.
|
|
|
|
Optional properties:
|
|
- dmas: Should contain dma specifiers for transmit and receive channels
|
|
- dma-names: Should contain "tx" for transmit and "rx" for receive channels
|
|
- qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be
|
|
used with TX DMA channel. Required when using DMA for transmission
|
|
with UARTDM v1.3 and below.
|
|
- qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be
|
|
used with RX DMA channel. Required when using DMA for reception
|
|
with UARTDM v1.3 and below.
|
|
|
|
Note: Aliases may be defined to ensure the correct ordering of the UARTs.
|
|
The alias serialN will result in the UART being assigned port N. If any
|
|
serialN alias exists, then an alias must exist for each enabled UART. The
|
|
serialN aliases should be in a .dts file instead of in a .dtsi file.
|
|
|
|
Examples:
|
|
|
|
- A uartdm v1.4 device with dma capabilities.
|
|
|
|
serial@f991e000 {
|
|
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
|
|
reg = <0xf991e000 0x1000>;
|
|
interrupts = <0 108 0x0>;
|
|
clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
|
|
clock-names = "core", "iface";
|
|
dmas = <&dma0 0>, <&dma0 1>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
|
|
- A uartdm v1.3 device without dma capabilities and part of a GSBI complex.
|
|
|
|
serial@19c40000 {
|
|
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
|
|
reg = <0x19c40000 0x1000>,
|
|
<0x19c00000 0x1000>;
|
|
interrupts = <0 195 0x0>;
|
|
clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>;
|
|
clock-names = "core", "iface";
|
|
};
|
|
|
|
- serialN alias.
|
|
|
|
aliases {
|
|
serial0 = &uarta;
|
|
serial1 = &uartc;
|
|
serial2 = &uartb;
|
|
};
|
|
|
|
uarta: serial@12490000 {
|
|
};
|
|
|
|
uartb: serial@16340000 {
|
|
};
|
|
|
|
uartc: serial@1a240000 {
|
|
};
|