mirror of https://gitee.com/openkylin/linux.git
163 lines
4.6 KiB
Plaintext
163 lines
4.6 KiB
Plaintext
Qualcomm PMIC Multi-Purpose Pin (MPP) block
|
|
|
|
This binding describes the MPP block(s) found in the 8xxx series
|
|
of PMIC's from Qualcomm.
|
|
|
|
- compatible:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: Should contain one of:
|
|
"qcom,pm8841-mpp",
|
|
"qcom,pm8941-mpp",
|
|
"qcom,pma8084-mpp",
|
|
|
|
- reg:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: Register base of the MPP block and length.
|
|
|
|
- interrupts:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: Must contain an array of encoded interrupt specifiers for
|
|
each available MPP
|
|
|
|
- gpio-controller:
|
|
Usage: required
|
|
Value type: <none>
|
|
Definition: Mark the device node as a GPIO controller
|
|
|
|
- #gpio-cells:
|
|
Usage: required
|
|
Value type: <u32>
|
|
Definition: Must be 2;
|
|
the first cell will be used to define MPP number and the
|
|
second denotes the flags for this MPP
|
|
|
|
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
|
|
a general description of GPIO and interrupt bindings.
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices, including the meaning of the
|
|
phrase "pin configuration node".
|
|
|
|
The pin configuration nodes act as a container for an arbitrary number of
|
|
subnodes. Each of these subnodes represents some desired configuration for a
|
|
pin or a list of pins. This configuration can include the
|
|
mux function to select on those pin(s), and various pin configuration
|
|
parameters, as listed below.
|
|
|
|
SUBNODES:
|
|
|
|
The name of each subnode is not important; all subnodes should be enumerated
|
|
and processed purely based on their content.
|
|
|
|
Each subnode only affects those parameters that are explicitly listed. In
|
|
other words, a subnode that lists a mux function but no pin configuration
|
|
parameters implies no information about any pin configuration parameters.
|
|
Similarly, a pin subnode that describes a pullup parameter implies no
|
|
information about e.g. the mux function.
|
|
|
|
The following generic properties as defined in pinctrl-bindings.txt are valid
|
|
to specify in a pin configuration subnode:
|
|
|
|
- pins:
|
|
Usage: required
|
|
Value type: <string-array>
|
|
Definition: List of MPP pins affected by the properties specified in
|
|
this subnode. Valid pins are:
|
|
mpp1-mpp4 for pm8841
|
|
mpp1-mpp8 for pm8941
|
|
mpp1-mpp4 for pma8084
|
|
|
|
- function:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: Specify the alternative function to be configured for the
|
|
specified pins. Valid values are:
|
|
"normal",
|
|
"paired",
|
|
"dtest1",
|
|
"dtest2",
|
|
"dtest3",
|
|
"dtest4"
|
|
|
|
- bias-disable:
|
|
Usage: optional
|
|
Value type: <none>
|
|
Definition: The specified pins should be configured as no pull.
|
|
|
|
- bias-pull-up:
|
|
Usage: optional
|
|
Value type: <u32>
|
|
Definition: The specified pins should be configured as pull up.
|
|
Valid values are 600, 10000 and 30000 in bidirectional mode
|
|
only, i.e. when operating in qcom,analog-mode and input and
|
|
outputs are enabled. The hardware ignores the configuration
|
|
when operating in other modes.
|
|
|
|
- bias-high-impedance:
|
|
Usage: optional
|
|
Value type: <none>
|
|
Definition: The specified pins will put in high-Z mode and disabled.
|
|
|
|
- input-enable:
|
|
Usage: optional
|
|
Value type: <none>
|
|
Definition: The specified pins are put in input mode, i.e. their input
|
|
buffer is enabled
|
|
|
|
- output-high:
|
|
Usage: optional
|
|
Value type: <none>
|
|
Definition: The specified pins are configured in output mode, driven
|
|
high.
|
|
|
|
- output-low:
|
|
Usage: optional
|
|
Value type: <none>
|
|
Definition: The specified pins are configured in output mode, driven
|
|
low.
|
|
|
|
- power-source:
|
|
Usage: optional
|
|
Value type: <u32>
|
|
Definition: Selects the power source for the specified pins. Valid power
|
|
sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
|
|
|
|
- qcom,analog-mode:
|
|
Usage: optional
|
|
Value type: <none>
|
|
Definition: Selects Analog mode of operation: combined with input-enable
|
|
and/or output-high, output-low MPP could operate as
|
|
Bidirectional Logic, Analog Input, Analog Output.
|
|
|
|
- qcom,amux-route:
|
|
Usage: optional
|
|
Value type: <u32>
|
|
Definition: Selects the source for analog input. Valid values are
|
|
defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
|
|
PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6...
|
|
|
|
Example:
|
|
|
|
mpps@a000 {
|
|
compatible = "qcom,pm8841-mpp";
|
|
reg = <0xa000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pm8841_default>;
|
|
|
|
pm8841_default: default {
|
|
gpio {
|
|
pins = "mpp1", "mpp2", "mpp3", "mpp4";
|
|
function = "normal";
|
|
input-enable;
|
|
power-source = <PM8841_MPP_S3>;
|
|
};
|
|
};
|
|
};
|