linux/arch/arm/mach-spear/spear3xx.c

111 lines
2.9 KiB
C

/*
* arch/arm/mach-spear3xx/spear3xx.c
*
* SPEAr3XX machines common source file
*
* Copyright (C) 2009-2012 ST Microelectronics
* Viresh Kumar <vireshk@kernel.org>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#define pr_fmt(fmt) "SPEAr3xx: " fmt
#include <linux/amba/pl022.h>
#include <linux/amba/pl080.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <asm/mach/map.h>
#include "pl080.h"
#include "generic.h"
#include <mach/spear.h>
#include <mach/misc_regs.h>
/* ssp device registration */
struct pl022_ssp_controller pl022_plat_data = {
.bus_id = 0,
.enable_dma = 1,
.dma_filter = pl08x_filter_id,
.dma_tx_param = "ssp0_tx",
.dma_rx_param = "ssp0_rx",
/*
* This is number of spi devices that can be connected to spi. There are
* two type of chipselects on which slave devices can work. One is chip
* select provided by spi masters other is controlled through external
* gpio's. We can't use chipselect provided from spi master (because as
* soon as FIFO becomes empty, CS is disabled and transfer ends). So
* this number now depends on number of gpios available for spi. each
* slave on each master requires a separate gpio pin.
*/
.num_chipselect = 2,
};
/* dmac device registration */
struct pl08x_platform_data pl080_plat_data = {
.memcpy_burst_size = PL08X_BURST_SZ_16,
.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
.memcpy_prot_buff = true,
.memcpy_prot_cache = true,
.lli_buses = PL08X_AHB1,
.mem_buses = PL08X_AHB1,
.get_xfer_signal = pl080_get_signal,
.put_xfer_signal = pl080_put_signal,
};
/*
* Following will create 16MB static virtual/physical mappings
* PHYSICAL VIRTUAL
* 0xD0000000 0xFD000000
* 0xFC000000 0xFC000000
*/
struct map_desc spear3xx_io_desc[] __initdata = {
{
.virtual = (unsigned long)VA_SPEAR_ICM1_2_BASE,
.pfn = __phys_to_pfn(SPEAR_ICM1_2_BASE),
.length = SZ_16M,
.type = MT_DEVICE
}, {
.virtual = (unsigned long)VA_SPEAR_ICM3_SMI_CTRL_BASE,
.pfn = __phys_to_pfn(SPEAR_ICM3_SMI_CTRL_BASE),
.length = SZ_16M,
.type = MT_DEVICE
},
};
/* This will create static memory mapping for selected devices */
void __init spear3xx_map_io(void)
{
iotable_init(spear3xx_io_desc, ARRAY_SIZE(spear3xx_io_desc));
}
void __init spear3xx_timer_init(void)
{
char pclk_name[] = "pll3_clk";
struct clk *gpt_clk, *pclk;
spear3xx_clk_init(MISC_BASE, VA_SPEAR320_SOC_CONFIG_BASE);
/* get the system timer clock */
gpt_clk = clk_get_sys("gpt0", NULL);
if (IS_ERR(gpt_clk)) {
pr_err("%s:couldn't get clk for gpt\n", __func__);
BUG();
}
/* get the suitable parent clock for timer*/
pclk = clk_get(NULL, pclk_name);
if (IS_ERR(pclk)) {
pr_err("%s:couldn't get %s as parent for gpt\n",
__func__, pclk_name);
BUG();
}
clk_set_parent(gpt_clk, pclk);
clk_put(gpt_clk);
clk_put(pclk);
spear_setup_of_timer();
}