mirror of https://gitee.com/openkylin/linux.git
136 lines
4.7 KiB
Plaintext
136 lines
4.7 KiB
Plaintext
Faraday Technology FTPCI100 PCI Host Bridge
|
|
|
|
This PCI bridge is found inside that Cortina Systems Gemini SoC platform and
|
|
is a generic IP block from Faraday Technology. It exists in two variants:
|
|
plain and dual PCI. The plain version embeds a cascading interrupt controller
|
|
into the host bridge. The dual version routes the interrupts to the host
|
|
chips interrupt controller.
|
|
|
|
The host controller appear on the PCI bus with vendor ID 0x159b (Faraday
|
|
Technology) and product ID 0x4321.
|
|
|
|
Mandatory properties:
|
|
|
|
- compatible: ranging from specific to generic, should be one of
|
|
"cortina,gemini-pci", "faraday,ftpci100"
|
|
"cortina,gemini-pci-dual", "faraday,ftpci100-dual"
|
|
"faraday,ftpci100"
|
|
"faraday,ftpci100-dual"
|
|
- reg: memory base and size for the host bridge
|
|
- #address-cells: set to <3>
|
|
- #size-cells: set to <2>
|
|
- #interrupt-cells: set to <1>
|
|
- bus-range: set to <0x00 0xff>
|
|
- device_type, set to "pci"
|
|
- ranges: see pci.txt
|
|
- interrupt-map-mask: see pci.txt
|
|
- interrupt-map: see pci.txt
|
|
- dma-ranges: three ranges for the inbound memory region. The ranges must
|
|
be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB,
|
|
128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
|
|
pre-fetchable.
|
|
|
|
Optional properties:
|
|
- clocks: when present, this should contain the peripheral clock (PCLK) and the
|
|
PCI clock (PCICLK). If these are not present, they are assumed to be
|
|
hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz.
|
|
- clock-names: when present, this should contain "PCLK" for the peripheral
|
|
clock and "PCICLK" for the PCI-side clock.
|
|
|
|
Mandatory subnodes:
|
|
- For "faraday,ftpci100" a node representing the interrupt-controller inside the
|
|
host bridge is mandatory. It has the following mandatory properties:
|
|
- interrupt: see interrupt-controller/interrupts.txt
|
|
- interrupt-controller: see interrupt-controller/interrupts.txt
|
|
- #address-cells: set to <0>
|
|
- #interrupt-cells: set to <1>
|
|
|
|
I/O space considerations:
|
|
|
|
The plain variant has 128MiB of non-prefetchable memory space, whereas the
|
|
"dual" variant has 64MiB. Take this into account when describing the ranges.
|
|
|
|
Interrupt map considerations:
|
|
|
|
The "dual" variant will get INT A, B, C, D from the system interrupt controller
|
|
and should point to respective interrupt in that controller in its
|
|
interrupt-map.
|
|
|
|
The code which is the only documentation of how the Faraday PCI (the non-dual
|
|
variant) interrupts assigns the default interrupt mapping/swizzling has
|
|
typically been like this, doing the swizzling on the interrupt controller side
|
|
rather than in the interconnect:
|
|
|
|
interrupt-map-mask = <0xf800 0 0 7>;
|
|
interrupt-map =
|
|
<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
|
|
<0x4800 0 0 2 &pci_intc 1>,
|
|
<0x4800 0 0 3 &pci_intc 2>,
|
|
<0x4800 0 0 4 &pci_intc 3>,
|
|
<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
|
|
<0x5000 0 0 2 &pci_intc 2>,
|
|
<0x5000 0 0 3 &pci_intc 3>,
|
|
<0x5000 0 0 4 &pci_intc 0>,
|
|
<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
|
|
<0x5800 0 0 2 &pci_intc 3>,
|
|
<0x5800 0 0 3 &pci_intc 0>,
|
|
<0x5800 0 0 4 &pci_intc 1>,
|
|
<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
|
|
<0x6000 0 0 2 &pci_intc 0>,
|
|
<0x6000 0 0 3 &pci_intc 1>,
|
|
<0x6000 0 0 4 &pci_intc 2>;
|
|
|
|
Example:
|
|
|
|
pci@50000000 {
|
|
compatible = "cortina,gemini-pci", "faraday,ftpci100";
|
|
reg = <0x50000000 0x100>;
|
|
interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */
|
|
<26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */
|
|
<27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */
|
|
<28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
#interrupt-cells = <1>;
|
|
|
|
bus-range = <0x00 0xff>;
|
|
ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
|
|
<0x01000000 0 0 0x50000000 0 0x00100000>,
|
|
/* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
|
|
<0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
|
|
|
|
/* DMA ranges */
|
|
dma-ranges =
|
|
/* 128MiB at 0x00000000-0x07ffffff */
|
|
<0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
|
|
/* 64MiB at 0x00000000-0x03ffffff */
|
|
<0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
|
|
/* 64MiB at 0x00000000-0x03ffffff */
|
|
<0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
|
|
|
|
interrupt-map-mask = <0xf800 0 0 7>;
|
|
interrupt-map =
|
|
<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
|
|
<0x4800 0 0 2 &pci_intc 1>,
|
|
<0x4800 0 0 3 &pci_intc 2>,
|
|
<0x4800 0 0 4 &pci_intc 3>,
|
|
<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
|
|
<0x5000 0 0 2 &pci_intc 2>,
|
|
<0x5000 0 0 3 &pci_intc 3>,
|
|
<0x5000 0 0 4 &pci_intc 0>,
|
|
<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
|
|
<0x5800 0 0 2 &pci_intc 3>,
|
|
<0x5800 0 0 3 &pci_intc 0>,
|
|
<0x5800 0 0 4 &pci_intc 1>,
|
|
<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
|
|
<0x6000 0 0 2 &pci_intc 0>,
|
|
<0x6000 0 0 3 &pci_intc 0>,
|
|
<0x6000 0 0 4 &pci_intc 0>;
|
|
pci_intc: interrupt-controller {
|
|
interrupt-parent = <&intcon>;
|
|
interrupt-controller;
|
|
#address-cells = <0>;
|
|
#interrupt-cells = <1>;
|
|
};
|
|
};
|