mirror of https://gitee.com/openkylin/linux.git
70 lines
2.4 KiB
Plaintext
70 lines
2.4 KiB
Plaintext
HiSilicon STB PCIe host bridge DT description
|
|
|
|
The HiSilicon STB PCIe host controller is based on the DesignWare PCIe core.
|
|
It shares common functions with the DesignWare PCIe core driver and inherits
|
|
common properties defined in
|
|
Documentation/devicetree/bindings/pci/designware-pcie.txt.
|
|
|
|
Additional properties are described here:
|
|
|
|
Required properties
|
|
- compatible: Should be one of the following strings:
|
|
"hisilicon,hi3798cv200-pcie"
|
|
- reg: Should contain sysctl, rc_dbi, config registers location and length.
|
|
- reg-names: Must include the following entries:
|
|
"control": control registers of PCIe controller;
|
|
"rc-dbi": configuration space of PCIe controller;
|
|
"config": configuration transaction space of PCIe controller.
|
|
- bus-range: PCI bus numbers covered.
|
|
- interrupts: MSI interrupt.
|
|
- interrupt-names: Must include "msi" entries.
|
|
- clocks: List of phandle and clock specifier pairs as listed in clock-names
|
|
property.
|
|
- clock-name: Must include the following entries:
|
|
"aux": auxiliary gate clock;
|
|
"pipe": pipe gate clock;
|
|
"sys": sys gate clock;
|
|
"bus": bus gate clock.
|
|
- resets: List of phandle and reset specifier pairs as listed in reset-names
|
|
property.
|
|
- reset-names: Must include the following entries:
|
|
"soft": soft reset;
|
|
"sys": sys reset;
|
|
"bus": bus reset.
|
|
|
|
Optional properties:
|
|
- reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal.
|
|
- vpcie-supply: The regulator in charge of PCIe port power.
|
|
- phys: List of phandle and phy mode specifier, should be 0.
|
|
- phy-names: Must be "phy".
|
|
|
|
Example:
|
|
pcie@f9860000 {
|
|
compatible = "hisilicon,hi3798cv200-pcie";
|
|
reg = <0xf9860000 0x1000>,
|
|
<0xf0000000 0x2000>,
|
|
<0xf2000000 0x01000000>;
|
|
reg-names = "control", "rc-dbi", "config";
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
device_type = "pci";
|
|
bus-range = <0 15>;
|
|
num-lanes = <1>;
|
|
ranges=<0x81000000 0 0 0xf4000000 0 0x00010000
|
|
0x82000000 0 0xf3000000 0xf3000000 0 0x01000000>;
|
|
interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "msi";
|
|
#interrupt-cells = <1>;
|
|
interrupt-map-mask = <0 0 0 0>;
|
|
interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&crg PCIE_AUX_CLK>,
|
|
<&crg PCIE_PIPE_CLK>,
|
|
<&crg PCIE_SYS_CLK>,
|
|
<&crg PCIE_BUS_CLK>;
|
|
clock-names = "aux", "pipe", "sys", "bus";
|
|
resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>;
|
|
reset-names = "soft", "sys", "bus";
|
|
phys = <&combphy1 PHY_TYPE_PCIE>;
|
|
phy-names = "phy";
|
|
};
|