mirror of https://gitee.com/openkylin/linux.git
204 lines
8.0 KiB
ReStructuredText
204 lines
8.0 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0
|
|
|
|
============
|
|
I3C protocol
|
|
============
|
|
|
|
Disclaimer
|
|
==========
|
|
|
|
This chapter will focus on aspects that matter to software developers. For
|
|
everything hardware related (like how things are transmitted on the bus, how
|
|
collisions are prevented, ...) please have a look at the I3C specification.
|
|
|
|
This document is just a brief introduction to the I3C protocol and the concepts
|
|
it brings to the table. If you need more information, please refer to the MIPI
|
|
I3C specification (can be downloaded here
|
|
http://resources.mipi.org/mipi-i3c-v1-download).
|
|
|
|
Introduction
|
|
============
|
|
|
|
The I3C (pronounced 'eye-three-see') is a MIPI standardized protocol designed
|
|
to overcome I2C limitations (limited speed, external signals needed for
|
|
interrupts, no automatic detection of the devices connected to the bus, ...)
|
|
while remaining power-efficient.
|
|
|
|
I3C Bus
|
|
=======
|
|
|
|
An I3C bus is made of several I3C devices and possibly some I2C devices as
|
|
well, but let's focus on I3C devices for now.
|
|
|
|
An I3C device on the I3C bus can have one of the following roles:
|
|
|
|
* Master: the device is driving the bus. It's the one in charge of initiating
|
|
transactions or deciding who is allowed to talk on the bus (slave generated
|
|
events are possible in I3C, see below).
|
|
* Slave: the device acts as a slave, and is not able to send frames to another
|
|
slave on the bus. The device can still send events to the master on
|
|
its own initiative if the master allowed it.
|
|
|
|
I3C is a multi-master protocol, so there might be several masters on a bus,
|
|
though only one device can act as a master at a given time. In order to gain
|
|
bus ownership, a master has to follow a specific procedure.
|
|
|
|
Each device on the I3C bus has to be assigned a dynamic address to be able to
|
|
communicate. Until this is done, the device should only respond to a limited
|
|
set of commands. If it has a static address (also called legacy I2C address),
|
|
the device can reply to I2C transfers.
|
|
|
|
In addition to these per-device addresses, the protocol defines a broadcast
|
|
address in order to address all devices on the bus.
|
|
|
|
Once a dynamic address has been assigned to a device, this address will be used
|
|
for any direct communication with the device. Note that even after being
|
|
assigned a dynamic address, the device should still process broadcast messages.
|
|
|
|
I3C Device discovery
|
|
====================
|
|
|
|
The I3C protocol defines a mechanism to automatically discover devices present
|
|
on the bus, their capabilities and the functionalities they provide. In this
|
|
regard I3C is closer to a discoverable bus like USB than it is to I2C or SPI.
|
|
|
|
The discovery mechanism is called DAA (Dynamic Address Assignment), because it
|
|
not only discovers devices but also assigns them a dynamic address.
|
|
|
|
During DAA, each I3C device reports 3 important things:
|
|
|
|
* BCR: Bus Characteristic Register. This 8-bit register describes the device bus
|
|
related capabilities
|
|
* DCR: Device Characteristic Register. This 8-bit register describes the
|
|
functionalities provided by the device
|
|
* Provisional ID: A 48-bit unique identifier. On a given bus there should be no
|
|
Provisional ID collision, otherwise the discovery mechanism may fail.
|
|
|
|
I3C slave events
|
|
================
|
|
|
|
The I3C protocol allows slaves to generate events on their own, and thus allows
|
|
them to take temporary control of the bus.
|
|
|
|
This mechanism is called IBI for In Band Interrupts, and as stated in the name,
|
|
it allows devices to generate interrupts without requiring an external signal.
|
|
|
|
During DAA, each device on the bus has been assigned an address, and this
|
|
address will serve as a priority identifier to determine who wins if 2 different
|
|
devices are generating an interrupt at the same moment on the bus (the lower the
|
|
dynamic address the higher the priority).
|
|
|
|
Masters are allowed to inhibit interrupts if they want to. This inhibition
|
|
request can be broadcast (applies to all devices) or sent to a specific
|
|
device.
|
|
|
|
I3C Hot-Join
|
|
============
|
|
|
|
The Hot-Join mechanism is similar to USB hotplug. This mechanism allows
|
|
slaves to join the bus after it has been initialized by the master.
|
|
|
|
This covers the following use cases:
|
|
|
|
* the device is not powered when the bus is probed
|
|
* the device is hotplugged on the bus through an extension board
|
|
|
|
This mechanism is relying on slave events to inform the master that a new
|
|
device joined the bus and is waiting for a dynamic address.
|
|
|
|
The master is then free to address the request as it wishes: ignore it or
|
|
assign a dynamic address to the slave.
|
|
|
|
I3C transfer types
|
|
==================
|
|
|
|
If you omit SMBus (which is just a standardization on how to access registers
|
|
exposed by I2C devices), I2C has only one transfer type.
|
|
|
|
I3C defines 3 different classes of transfer in addition to I2C transfers which
|
|
are here for backward compatibility with I2C devices.
|
|
|
|
I3C CCC commands
|
|
----------------
|
|
|
|
CCC (Common Command Code) commands are meant to be used for anything that is
|
|
related to bus management and all features that are common to a set of devices.
|
|
|
|
CCC commands contain an 8-bit CCC ID describing the command that is executed.
|
|
The MSB of this ID specifies whether this is a broadcast command (bit7 = 0) or a
|
|
unicast one (bit7 = 1).
|
|
|
|
The command ID can be followed by a payload. Depending on the command, this
|
|
payload is either sent by the master sending the command (write CCC command),
|
|
or sent by the slave receiving the command (read CCC command). Of course, read
|
|
accesses only apply to unicast commands.
|
|
Note that, when sending a CCC command to a specific device, the device address
|
|
is passed in the first byte of the payload.
|
|
|
|
The payload length is not explicitly passed on the bus, and should be extracted
|
|
from the CCC ID.
|
|
|
|
Note that vendors can use a dedicated range of CCC IDs for their own commands
|
|
(0x61-0x7f and 0xe0-0xef).
|
|
|
|
I3C Private SDR transfers
|
|
-------------------------
|
|
|
|
Private SDR (Single Data Rate) transfers should be used for anything that is
|
|
device specific and does not require high transfer speed.
|
|
|
|
It is the equivalent of I2C transfers but in the I3C world. Each transfer is
|
|
passed the device address (dynamic address assigned during DAA), a payload
|
|
and a direction.
|
|
|
|
The only difference with I2C is that the transfer is much faster (typical clock
|
|
frequency is 12.5MHz).
|
|
|
|
I3C HDR commands
|
|
----------------
|
|
|
|
HDR commands should be used for anything that is device specific and requires
|
|
high transfer speed.
|
|
|
|
The first thing attached to an HDR command is the HDR mode. There are currently
|
|
3 different modes defined by the I3C specification (refer to the specification
|
|
for more details):
|
|
|
|
* HDR-DDR: Double Data Rate mode
|
|
* HDR-TSP: Ternary Symbol Pure. Only usable on busses with no I2C devices
|
|
* HDR-TSL: Ternary Symbol Legacy. Usable on busses with I2C devices
|
|
|
|
When sending an HDR command, the whole bus has to enter HDR mode, which is done
|
|
using a broadcast CCC command.
|
|
Once the bus has entered a specific HDR mode, the master sends the HDR command.
|
|
An HDR command is made of:
|
|
|
|
* one 16-bits command word in big endian
|
|
* N 16-bits data words in big endian
|
|
|
|
Those words may be wrapped with specific preambles/post-ambles which depend on
|
|
the chosen HDR mode and are detailed here (see the specification for more
|
|
details).
|
|
|
|
The 16-bits command word is made of:
|
|
|
|
* bit[15]: direction bit, read is 1, write is 0
|
|
* bit[14:8]: command code. Identifies the command being executed, the amount of
|
|
data words and their meaning
|
|
* bit[7:1]: I3C address of the device this command is addressed to
|
|
* bit[0]: reserved/parity-bit
|
|
|
|
Backward compatibility with I2C devices
|
|
=======================================
|
|
|
|
The I3C protocol has been designed to be backward compatible with I2C devices.
|
|
This backward compatibility allows one to connect a mix of I2C and I3C devices
|
|
on the same bus, though, in order to be really efficient, I2C devices should
|
|
be equipped with 50 ns spike filters.
|
|
|
|
I2C devices can't be discovered like I3C ones and have to be statically
|
|
declared. In order to let the master know what these devices are capable of
|
|
(both in terms of bus related limitations and functionalities), the software
|
|
has to provide some information, which is done through the LVR (Legacy I2C
|
|
Virtual Register).
|