mirror of https://gitee.com/openkylin/linux.git
128 lines
5.0 KiB
Plaintext
128 lines
5.0 KiB
Plaintext
* Freescale MXS Pin Controller
|
|
|
|
The pins controlled by mxs pin controller are organized in banks, each bank
|
|
has 32 pins. Each pin has 4 multiplexing functions, and generally, the 4th
|
|
function is GPIO. The configuration on the pins includes drive strength,
|
|
voltage and pull-up.
|
|
|
|
Required properties:
|
|
- compatible: "fsl,imx23-pinctrl" or "fsl,imx28-pinctrl"
|
|
- reg: Should contain the register physical address and length for the
|
|
pin controller.
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices.
|
|
|
|
The node of mxs pin controller acts as a container for an arbitrary number of
|
|
subnodes. Each of these subnodes represents some desired configuration for
|
|
a group of pins, and only affects those parameters that are explicitly listed.
|
|
In other words, a subnode that describes a drive strength parameter implies no
|
|
information about pull-up. For this reason, even seemingly boolean values are
|
|
actually tristates in this binding: unspecified, off, or on. Unspecified is
|
|
represented as an absent property, and off/on are represented as integer
|
|
values 0 and 1.
|
|
|
|
Those subnodes under mxs pin controller node will fall into two categories.
|
|
One is to set up a group of pins for a function, both mux selection and pin
|
|
configurations, and it's called group node in the binding document. The other
|
|
one is to adjust the pin configuration for some particular pins that need a
|
|
different configuration than what is defined in group node. The binding
|
|
document calls this type of node config node.
|
|
|
|
On mxs, there is no hardware pin group. The pin group in this binding only
|
|
means a group of pins put together for particular peripheral to work in
|
|
particular function, like SSP0 functioning as mmc0-8bit. That said, the
|
|
group node should include all the pins needed for one function rather than
|
|
having these pins defined in several group nodes. It also means each of
|
|
"pinctrl-*" phandle in client device node should only have one group node
|
|
pointed in there, while the phandle can have multiple config node referenced
|
|
there to adjust configurations for some pins in the group.
|
|
|
|
Required subnode-properties:
|
|
- fsl,pinmux-ids: An integer array. Each integer in the array specify a pin
|
|
with given mux function, with bank, pin and mux packed as below.
|
|
|
|
[15..12] : bank number
|
|
[11..4] : pin number
|
|
[3..0] : mux selection
|
|
|
|
This integer with mux selection packed is used as an entity by both group
|
|
and config nodes to identify a pin. The mux selection in the integer takes
|
|
effects only on group node, and will get ignored by driver with config node,
|
|
since config node is only meant to set up pin configurations.
|
|
|
|
Valid values for these integers are listed below.
|
|
|
|
- reg: Should be the index of the group nodes for same function. This property
|
|
is required only for group nodes, and should not be present in any config
|
|
nodes.
|
|
|
|
Optional subnode-properties:
|
|
- fsl,drive-strength: Integer.
|
|
0: MXS_DRIVE_4mA
|
|
1: MXS_DRIVE_8mA
|
|
2: MXS_DRIVE_12mA
|
|
3: MXS_DRIVE_16mA
|
|
- fsl,voltage: Integer.
|
|
0: MXS_VOLTAGE_LOW - 1.8 V
|
|
1: MXS_VOLTAGE_HIGH - 3.3 V
|
|
- fsl,pull-up: Integer.
|
|
0: MXS_PULL_DISABLE - Disable the internal pull-up
|
|
1: MXS_PULL_ENABLE - Enable the internal pull-up
|
|
|
|
Note that when enabling the pull-up, the internal pad keeper gets disabled.
|
|
Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up
|
|
will only disable the internal pad keeper.
|
|
|
|
Examples:
|
|
|
|
pinctrl@80018000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,imx28-pinctrl";
|
|
reg = <0x80018000 2000>;
|
|
|
|
mmc0_8bit_pins_a: mmc0-8bit@0 {
|
|
reg = <0>;
|
|
fsl,pinmux-ids = <
|
|
MX28_PAD_SSP0_DATA0__SSP0_D0
|
|
MX28_PAD_SSP0_DATA1__SSP0_D1
|
|
MX28_PAD_SSP0_DATA2__SSP0_D2
|
|
MX28_PAD_SSP0_DATA3__SSP0_D3
|
|
MX28_PAD_SSP0_DATA4__SSP0_D4
|
|
MX28_PAD_SSP0_DATA5__SSP0_D5
|
|
MX28_PAD_SSP0_DATA6__SSP0_D6
|
|
MX28_PAD_SSP0_DATA7__SSP0_D7
|
|
MX28_PAD_SSP0_CMD__SSP0_CMD
|
|
MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
|
|
MX28_PAD_SSP0_SCK__SSP0_SCK
|
|
>;
|
|
fsl,drive-strength = <MXS_DRIVE_4mA>;
|
|
fsl,voltage = <MXS_VOLTAGE_HIGH>;
|
|
fsl,pull-up = <MXS_PULL_ENABLE>;
|
|
};
|
|
|
|
mmc_cd_cfg: mmc-cd-cfg {
|
|
fsl,pinmux-ids = <MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT>;
|
|
fsl,pull-up = <MXS_PULL_DISABLE>;
|
|
};
|
|
|
|
mmc_sck_cfg: mmc-sck-cfg {
|
|
fsl,pinmux-ids = <MX28_PAD_SSP0_SCK__SSP0_SCK>;
|
|
fsl,drive-strength = <MXS_DRIVE_12mA>;
|
|
fsl,pull-up = <MXS_PULL_DISABLE>;
|
|
};
|
|
};
|
|
|
|
In this example, group node mmc0-8bit defines a group of pins for mxs SSP0
|
|
to function as a 8-bit mmc device, with 8mA, 3.3V and pull-up configurations
|
|
applied on all these pins. And config nodes mmc-cd-cfg and mmc-sck-cfg are
|
|
adjusting the configuration for pins card-detection and clock from what group
|
|
node mmc0-8bit defines. Only the configuration properties to be adjusted need
|
|
to be listed in the config nodes.
|
|
|
|
Valid values for i.MX28/i.MX23 pinmux-id are defined in
|
|
arch/arm/boot/dts/imx28-pinfunc.h and arch/arm/boot/dts/imx23-pinfunc.h.
|
|
The definitions for the padconfig properties can be found in
|
|
arch/arm/boot/dts/mxs-pinfunc.h.
|