openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity
linux/drivers/extcon/extcon-intel-cht-wc.c

459 lines
13 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0
/*
* Extcon charger detection driver for Intel Cherrytrail Whiskey Cove PMIC
* Copyright (C) 2017 Hans de Goede <hdegoede@redhat.com>
*
* Based on various non upstream patches to support the CHT Whiskey Cove PMIC:
* Copyright (C) 2013-2015 Intel Corporation. All rights reserved.
*/
#include <linux/extcon-provider.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/mfd/intel_soc_pmic.h>
#include <linux/module.h>
#include <linux/mod_devicetable.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/slab.h>
#include "extcon-intel.h"
#define CHT_WC_PHYCTRL 0x5e07
#define CHT_WC_CHGRCTRL0 0x5e16
#define CHT_WC_CHGRCTRL0_CHGRRESET BIT(0)
#define CHT_WC_CHGRCTRL0_EMRGCHREN BIT(1)
#define CHT_WC_CHGRCTRL0_EXTCHRDIS BIT(2)
#define CHT_WC_CHGRCTRL0_SWCONTROL BIT(3)
#define CHT_WC_CHGRCTRL0_TTLCK BIT(4)
#define CHT_WC_CHGRCTRL0_CCSM_OFF BIT(5)
#define CHT_WC_CHGRCTRL0_DBPOFF BIT(6)
#define CHT_WC_CHGRCTRL0_CHR_WDT_NOKICK BIT(7)
#define CHT_WC_CHGRCTRL1 0x5e17
#define CHT_WC_CHGRCTRL1_FUSB_INLMT_100 BIT(0)
#define CHT_WC_CHGRCTRL1_FUSB_INLMT_150 BIT(1)
#define CHT_WC_CHGRCTRL1_FUSB_INLMT_500 BIT(2)
#define CHT_WC_CHGRCTRL1_FUSB_INLMT_900 BIT(3)
#define CHT_WC_CHGRCTRL1_FUSB_INLMT_1500 BIT(4)
#define CHT_WC_CHGRCTRL1_FTEMP_EVENT BIT(5)
#define CHT_WC_CHGRCTRL1_OTGMODE BIT(6)
#define CHT_WC_CHGRCTRL1_DBPEN BIT(7)
#define CHT_WC_USBSRC 0x5e29
#define CHT_WC_USBSRC_STS_MASK GENMASK(1, 0)
#define CHT_WC_USBSRC_STS_SUCCESS 2
#define CHT_WC_USBSRC_STS_FAIL 3
#define CHT_WC_USBSRC_TYPE_SHIFT 2
#define CHT_WC_USBSRC_TYPE_MASK GENMASK(5, 2)
#define CHT_WC_USBSRC_TYPE_NONE 0
#define CHT_WC_USBSRC_TYPE_SDP 1
#define CHT_WC_USBSRC_TYPE_DCP 2
#define CHT_WC_USBSRC_TYPE_CDP 3
#define CHT_WC_USBSRC_TYPE_ACA 4
#define CHT_WC_USBSRC_TYPE_SE1 5
#define CHT_WC_USBSRC_TYPE_MHL 6
#define CHT_WC_USBSRC_TYPE_FLOATING 7
#define CHT_WC_USBSRC_TYPE_OTHER 8
#define CHT_WC_USBSRC_TYPE_DCP_EXTPHY 9
#define CHT_WC_CHGDISCTRL 0x5e2f
#define CHT_WC_CHGDISCTRL_OUT BIT(0)
/* 0 - open drain, 1 - regular push-pull output */
#define CHT_WC_CHGDISCTRL_DRV BIT(4)
/* 0 - pin is controlled by SW, 1 - by HW */
#define CHT_WC_CHGDISCTRL_FN BIT(6)
#define CHT_WC_PWRSRC_IRQ 0x6e03
#define CHT_WC_PWRSRC_IRQ_MASK 0x6e0f
#define CHT_WC_PWRSRC_STS 0x6e1e
#define CHT_WC_PWRSRC_VBUS BIT(0)
#define CHT_WC_PWRSRC_DC BIT(1)
#define CHT_WC_PWRSRC_BATT BIT(2)
#define CHT_WC_PWRSRC_USBID_MASK GENMASK(4, 3)
#define CHT_WC_PWRSRC_USBID_SHIFT 3
#define CHT_WC_PWRSRC_RID_ACA 0
#define CHT_WC_PWRSRC_RID_GND 1
#define CHT_WC_PWRSRC_RID_FLOAT 2
#define CHT_WC_VBUS_GPIO_CTLO 0x6e2d
#define CHT_WC_VBUS_GPIO_CTLO_OUTPUT BIT(0)
#define CHT_WC_VBUS_GPIO_CTLO_DRV_OD BIT(4)
#define CHT_WC_VBUS_GPIO_CTLO_DIR_OUT BIT(5)
enum cht_wc_mux_select {
MUX_SEL_PMIC = 0,
MUX_SEL_SOC,
};
static const unsigned int cht_wc_extcon_cables[] = {
EXTCON_USB,
EXTCON_USB_HOST,
EXTCON_CHG_USB_SDP,
EXTCON_CHG_USB_CDP,
EXTCON_CHG_USB_DCP,
EXTCON_CHG_USB_ACA,
EXTCON_NONE,
};
struct cht_wc_extcon_data {
struct device *dev;
struct regmap *regmap;
struct extcon_dev *edev;
unsigned int previous_cable;
bool usb_host;
};
static int cht_wc_extcon_get_id(struct cht_wc_extcon_data *ext, int pwrsrc_sts)
{
switch ((pwrsrc_sts & CHT_WC_PWRSRC_USBID_MASK) >> CHT_WC_PWRSRC_USBID_SHIFT) {
case CHT_WC_PWRSRC_RID_GND:
return INTEL_USB_ID_GND;
case CHT_WC_PWRSRC_RID_FLOAT:
return INTEL_USB_ID_FLOAT;
case CHT_WC_PWRSRC_RID_ACA:
default:
/*
* Once we have IIO support for the GPADC we should read
* the USBID GPADC channel here and determine ACA role
* based on that.
*/
return INTEL_USB_ID_FLOAT;
}
}
static int cht_wc_extcon_get_charger(struct cht_wc_extcon_data *ext,
bool ignore_errors)
{
int ret, usbsrc, status;
unsigned long timeout;
/* Charger detection can take upto 600ms, wait 800ms max. */
timeout = jiffies + msecs_to_jiffies(800);
do {
ret = regmap_read(ext->regmap, CHT_WC_USBSRC, &usbsrc);
if (ret) {
dev_err(ext->dev, "Error reading usbsrc: %d\n", ret);
return ret;
}
status = usbsrc & CHT_WC_USBSRC_STS_MASK;
if (status == CHT_WC_USBSRC_STS_SUCCESS ||
status == CHT_WC_USBSRC_STS_FAIL)
break;
msleep(50); /* Wait a bit before retrying */
} while (time_before(jiffies, timeout));
if (status != CHT_WC_USBSRC_STS_SUCCESS) {
if (ignore_errors)
return EXTCON_CHG_USB_SDP; /* Save fallback */
if (status == CHT_WC_USBSRC_STS_FAIL)
dev_warn(ext->dev, "Could not detect charger type\n");
else
dev_warn(ext->dev, "Timeout detecting charger type\n");
return EXTCON_CHG_USB_SDP; /* Save fallback */
}
usbsrc = (usbsrc & CHT_WC_USBSRC_TYPE_MASK) >> CHT_WC_USBSRC_TYPE_SHIFT;
switch (usbsrc) {
default:
dev_warn(ext->dev,
"Unhandled charger type %d, defaulting to SDP\n",
ret);
return EXTCON_CHG_USB_SDP;
case CHT_WC_USBSRC_TYPE_SDP:
case CHT_WC_USBSRC_TYPE_FLOATING:
case CHT_WC_USBSRC_TYPE_OTHER:
return EXTCON_CHG_USB_SDP;
case CHT_WC_USBSRC_TYPE_CDP:
return EXTCON_CHG_USB_CDP;
case CHT_WC_USBSRC_TYPE_DCP:
case CHT_WC_USBSRC_TYPE_DCP_EXTPHY:
case CHT_WC_USBSRC_TYPE_MHL: /* MHL2+ delivers upto 2A, treat as DCP */
return EXTCON_CHG_USB_DCP;
case CHT_WC_USBSRC_TYPE_ACA:
return EXTCON_CHG_USB_ACA;
}
}
static void cht_wc_extcon_set_phymux(struct cht_wc_extcon_data *ext, u8 state)
{
int ret;
ret = regmap_write(ext->regmap, CHT_WC_PHYCTRL, state);
if (ret)
dev_err(ext->dev, "Error writing phyctrl: %d\n", ret);
}
static void cht_wc_extcon_set_5v_boost(struct cht_wc_extcon_data *ext,
bool enable)
{
int ret, val;
/*
* The 5V boost converter is enabled through a gpio on the PMIC, since
* there currently is no gpio driver we access the gpio reg directly.
*/
val = CHT_WC_VBUS_GPIO_CTLO_DRV_OD | CHT_WC_VBUS_GPIO_CTLO_DIR_OUT;
if (enable)
val |= CHT_WC_VBUS_GPIO_CTLO_OUTPUT;
ret = regmap_write(ext->regmap, CHT_WC_VBUS_GPIO_CTLO, val);
if (ret)
dev_err(ext->dev, "Error writing Vbus GPIO CTLO: %d\n", ret);
}
static void cht_wc_extcon_set_otgmode(struct cht_wc_extcon_data *ext,
bool enable)
{
unsigned int val = enable ? CHT_WC_CHGRCTRL1_OTGMODE : 0;
int ret;
ret = regmap_update_bits(ext->regmap, CHT_WC_CHGRCTRL1,
CHT_WC_CHGRCTRL1_OTGMODE, val);
if (ret)
dev_err(ext->dev, "Error updating CHGRCTRL1 reg: %d\n", ret);
}
static void cht_wc_extcon_enable_charging(struct cht_wc_extcon_data *ext,
bool enable)
{
unsigned int val = enable ? 0 : CHT_WC_CHGDISCTRL_OUT;
int ret;
ret = regmap_update_bits(ext->regmap, CHT_WC_CHGDISCTRL,
CHT_WC_CHGDISCTRL_OUT, val);
if (ret)
dev_err(ext->dev, "Error updating CHGDISCTRL reg: %d\n", ret);
}
/* Small helper to sync EXTCON_CHG_USB_SDP and EXTCON_USB state */
static void cht_wc_extcon_set_state(struct cht_wc_extcon_data *ext,
unsigned int cable, bool state)
{
extcon_set_state_sync(ext->edev, cable, state);
if (cable == EXTCON_CHG_USB_SDP)
extcon_set_state_sync(ext->edev, EXTCON_USB, state);
}
static void cht_wc_extcon_pwrsrc_event(struct cht_wc_extcon_data *ext)
{
int ret, pwrsrc_sts, id;
unsigned int cable = EXTCON_NONE;
/* Ignore errors in host mode, as the 5v boost converter is on then */
bool ignore_get_charger_errors = ext->usb_host;
ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_STS, &pwrsrc_sts);
if (ret) {
dev_err(ext->dev, "Error reading pwrsrc status: %d\n", ret);
return;
}
id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
if (id == INTEL_USB_ID_GND) {
cht_wc_extcon_enable_charging(ext, false);
cht_wc_extcon_set_otgmode(ext, true);
/* The 5v boost causes a false VBUS / SDP detect, skip */
goto charger_det_done;
}
cht_wc_extcon_set_otgmode(ext, false);
cht_wc_extcon_enable_charging(ext, true);
/* Plugged into a host/charger or not connected? */
if (!(pwrsrc_sts & CHT_WC_PWRSRC_VBUS)) {
/* Route D+ and D- to PMIC for future charger detection */
cht_wc_extcon_set_phymux(ext, MUX_SEL_PMIC);
goto set_state;
}
ret = cht_wc_extcon_get_charger(ext, ignore_get_charger_errors);
if (ret >= 0)
cable = ret;
charger_det_done:
/* Route D+ and D- to SoC for the host or gadget controller */
cht_wc_extcon_set_phymux(ext, MUX_SEL_SOC);
set_state:
if (cable != ext->previous_cable) {
cht_wc_extcon_set_state(ext, cable, true);
cht_wc_extcon_set_state(ext, ext->previous_cable, false);
ext->previous_cable = cable;
}
ext->usb_host = ((id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A));
extcon_set_state_sync(ext->edev, EXTCON_USB_HOST, ext->usb_host);
}
static irqreturn_t cht_wc_extcon_isr(int irq, void *data)
{
struct cht_wc_extcon_data *ext = data;
int ret, irqs;
ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_IRQ, &irqs);
if (ret) {
dev_err(ext->dev, "Error reading irqs: %d\n", ret);
return IRQ_NONE;
}
cht_wc_extcon_pwrsrc_event(ext);
ret = regmap_write(ext->regmap, CHT_WC_PWRSRC_IRQ, irqs);
if (ret) {
dev_err(ext->dev, "Error writing irqs: %d\n", ret);
return IRQ_NONE;
}
return IRQ_HANDLED;
}
static int cht_wc_extcon_sw_control(struct cht_wc_extcon_data *ext, bool enable)
{
int ret, mask, val;
val = enable ? 0 : CHT_WC_CHGDISCTRL_FN;
ret = regmap_update_bits(ext->regmap, CHT_WC_CHGDISCTRL,
CHT_WC_CHGDISCTRL_FN, val);
if (ret)
dev_err(ext->dev,
"Error setting sw control for CHGDIS pin: %d\n",
ret);
mask = CHT_WC_CHGRCTRL0_SWCONTROL | CHT_WC_CHGRCTRL0_CCSM_OFF;
val = enable ? mask : 0;
ret = regmap_update_bits(ext->regmap, CHT_WC_CHGRCTRL0, mask, val);
if (ret)
dev_err(ext->dev, "Error setting sw control: %d\n", ret);
return ret;
}
static int cht_wc_extcon_probe(struct platform_device *pdev)
{
struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
struct cht_wc_extcon_data *ext;
unsigned long mask = ~(CHT_WC_PWRSRC_VBUS | CHT_WC_PWRSRC_USBID_MASK);
int pwrsrc_sts, id;
int irq, ret;
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
ext = devm_kzalloc(&pdev->dev, sizeof(*ext), GFP_KERNEL);
if (!ext)
return -ENOMEM;
ext->dev = &pdev->dev;
ext->regmap = pmic->regmap;
ext->previous_cable = EXTCON_NONE;
/* Initialize extcon device */
ext->edev = devm_extcon_dev_allocate(ext->dev, cht_wc_extcon_cables);
if (IS_ERR(ext->edev))
return PTR_ERR(ext->edev);
/*
* When a host-cable is detected the BIOS enables an external 5v boost
* converter to power connected devices there are 2 problems with this:
* 1) This gets seen by the external battery charger as a valid Vbus
* supply and it then tries to feed Vsys from this creating a
* feedback loop which causes aprox. 300 mA extra battery drain
* (and unless we drive the external-charger-disable pin high it
* also tries to charge the battery causing even more feedback).
* 2) This gets seen by the pwrsrc block as a SDP USB Vbus supply
* Since the external battery charger has its own 5v boost converter
* which does not have these issues, we simply turn the separate
* external 5v boost converter off and leave it off entirely.
*/
cht_wc_extcon_set_5v_boost(ext, false);
/* Enable sw control */
ret = cht_wc_extcon_sw_control(ext, true);
if (ret)
goto disable_sw_control;
/* Disable charging by external battery charger */
cht_wc_extcon_enable_charging(ext, false);
/* Register extcon device */
ret = devm_extcon_dev_register(ext->dev, ext->edev);
if (ret) {
dev_err(ext->dev, "Error registering extcon device: %d\n", ret);
goto disable_sw_control;
}
ret = regmap_read(ext->regmap, CHT_WC_PWRSRC_STS, &pwrsrc_sts);
if (ret) {
dev_err(ext->dev, "Error reading pwrsrc status: %d\n", ret);
goto disable_sw_control;
}
/*
* If no USB host or device connected, route D+ and D- to PMIC for
* initial charger detection
*/
id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
if (id != INTEL_USB_ID_GND)
cht_wc_extcon_set_phymux(ext, MUX_SEL_PMIC);
/* Get initial state */
cht_wc_extcon_pwrsrc_event(ext);
ret = devm_request_threaded_irq(ext->dev, irq, NULL, cht_wc_extcon_isr,
IRQF_ONESHOT, pdev->name, ext);
if (ret) {
dev_err(ext->dev, "Error requesting interrupt: %d\n", ret);
goto disable_sw_control;
}
/* Unmask irqs */
ret = regmap_write(ext->regmap, CHT_WC_PWRSRC_IRQ_MASK, mask);
if (ret) {
dev_err(ext->dev, "Error writing irq-mask: %d\n", ret);
goto disable_sw_control;
}
platform_set_drvdata(pdev, ext);
return 0;
disable_sw_control:
cht_wc_extcon_sw_control(ext, false);
return ret;
}
static int cht_wc_extcon_remove(struct platform_device *pdev)
{
struct cht_wc_extcon_data *ext = platform_get_drvdata(pdev);
cht_wc_extcon_sw_control(ext, false);
return 0;
}
static const struct platform_device_id cht_wc_extcon_table[] = {
{ .name = "cht_wcove_pwrsrc" },
{},
};
MODULE_DEVICE_TABLE(platform, cht_wc_extcon_table);
static struct platform_driver cht_wc_extcon_driver = {
.probe = cht_wc_extcon_probe,
.remove = cht_wc_extcon_remove,
.id_table = cht_wc_extcon_table,
.driver = {
.name = "cht_wcove_pwrsrc",
},
};
module_platform_driver(cht_wc_extcon_driver);
MODULE_DESCRIPTION("Intel Cherrytrail Whiskey Cove PMIC extcon driver");
MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
MODULE_LICENSE("GPL v2");
Reference in New Issue View Git Blame Copy Permalink