mirror of https://gitee.com/openkylin/linux.git
75 lines
2.7 KiB
Plaintext
75 lines
2.7 KiB
Plaintext
Device tree configuration for i2c-ocores
|
|
|
|
Required properties:
|
|
- compatible : "opencores,i2c-ocores"
|
|
"aeroflexgaisler,i2cmst"
|
|
"sifive,fu540-c000-i2c", "sifive,i2c0"
|
|
For Opencore based I2C IP block reimplemented in
|
|
FU540-C000 SoC. Please refer to sifive-blocks-ip-versioning.txt
|
|
for additional details.
|
|
- reg : bus address start and address range size of device
|
|
- clocks : handle to the controller clock; see the note below.
|
|
Mutually exclusive with opencores,ip-clock-frequency
|
|
- opencores,ip-clock-frequency: frequency of the controller clock in Hz;
|
|
see the note below. Mutually exclusive with clocks
|
|
- #address-cells : should be <1>
|
|
- #size-cells : should be <0>
|
|
|
|
Optional properties:
|
|
- interrupts : interrupt number.
|
|
- clock-frequency : frequency of bus clock in Hz; see the note below.
|
|
Defaults to 100 KHz when the property is not specified
|
|
- reg-shift : device register offsets are shifted by this value
|
|
- reg-io-width : io register width in bytes (1, 2 or 4)
|
|
- regstep : deprecated, use reg-shift above
|
|
|
|
Note
|
|
clock-frequency property is meant to control the bus frequency for i2c bus
|
|
drivers, but it was incorrectly used to specify i2c controller input clock
|
|
frequency. So the following rules are set to fix this situation:
|
|
- if clock-frequency is present and neither opencores,ip-clock-frequency nor
|
|
clocks are, then clock-frequency specifies i2c controller clock frequency.
|
|
This is to keep backwards compatibility with setups using old DTB. i2c bus
|
|
frequency is fixed at 100 KHz.
|
|
- if clocks is present it specifies i2c controller clock. clock-frequency
|
|
property specifies i2c bus frequency.
|
|
- if opencores,ip-clock-frequency is present it specifies i2c controller
|
|
clock frequency. clock-frequency property specifies i2c bus frequency.
|
|
|
|
Examples:
|
|
|
|
i2c0: ocores@a0000000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "opencores,i2c-ocores";
|
|
reg = <0xa0000000 0x8>;
|
|
interrupts = <10>;
|
|
opencores,ip-clock-frequency = <20000000>;
|
|
|
|
reg-shift = <0>; /* 8 bit registers */
|
|
reg-io-width = <1>; /* 8 bit read/write */
|
|
|
|
dummy@60 {
|
|
compatible = "dummy";
|
|
reg = <0x60>;
|
|
};
|
|
};
|
|
or
|
|
i2c0: ocores@a0000000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "opencores,i2c-ocores";
|
|
reg = <0xa0000000 0x8>;
|
|
interrupts = <10>;
|
|
clocks = <&osc>;
|
|
clock-frequency = <400000>; /* i2c bus frequency 400 KHz */
|
|
|
|
reg-shift = <0>; /* 8 bit registers */
|
|
reg-io-width = <1>; /* 8 bit read/write */
|
|
|
|
dummy@60 {
|
|
compatible = "dummy";
|
|
reg = <0x60>;
|
|
};
|
|
};
|